HP StorageWorks XP Audit Log reference guide: HP XP12000 Disk Array, HP XP10000 Disk Array, HP 200 Storage Virtualization System (5697-8004, March 2009)

ManualsBrandsHP ManualsStorageHP StorageWorks XP12000 Disk Array SSP

HP StorageWorks

XP Audit Log reference guide

HP XP12000 Disk Array

HP XP10000 Disk Array

HP 200 Storage Virtualization System

This guide provides information about using the audit log feature on the disk arrays, the format of the audit logs,

and details about the audit log functions and operations.

Part number: 5697-8004

Eighth edition: February 2009

Summary of content (332 pages)

PAGE 1
HP StorageWorks XP Audit Log reference guide HP XP12000 Disk Array HP XP10000 Disk Array HP 200 Storage Virtualization System nl nl This guide provides information about using the audit log feature on the disk arrays, the format of the audit logs, and details about the audit log functions and operations.
PAGE 2
Legal and notice information © Copyright 1999, 2009 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
PAGE 3
Contents 1 Introduction ..................................................................................... 21 Introduction to audit log ............................................................................................................. Increasing data security ...................................................................................................... Providing an audit trail for regulatory compliance ...................................................................
PAGE 4
Delete M/F DCR operation ........................................................................................................ Delete Open DCR operation ...................................................................................................... Set M/F DCR operation ............................................................................................................. Set Open DCR operation ..................................................................................................
PAGE 5
Delete Host Group operation ...................................................................................................... 94 Delete iSCSI Name operation ..................................................................................................... 95 Delete iSCSI Target operation ..................................................................................................... 95 Delete LU Path operation .....................................................................................
PAGE 6
17 LUN Manager (LUNM) function ..................................................... 141 Add Host Group operation ...................................................................................................... Add iSCSI Name operation ..................................................................................................... Add iSCSI Target operation ...................................................................................................... Add LU Path operation ................
PAGE 7
Transfer Config operation ........................................................................................................ Type Change operation ........................................................................................................... Verify operation ...................................................................................................................... Verify Stop operation .............................................................................................
PAGE 8
Initialize operation .................................................................................................................. Option operation .................................................................................................................... Resync Pair operation .............................................................................................................. Set SCP Time operation ......................................................................................
PAGE 9
32 Continuous Access XP Journal function ............................................ 249 Journal-Option operation ......................................................................................................... Journal-Vol operation ............................................................................................................... Journal-Vol operation ............................................................................................................... Paircreate operation ..
PAGE 10
Set Plan Condition operation .................................................................................................... 292 Set Reserved Vol operation ....................................................................................................... 293 37 HP Disk/Cache Partition function .................................................... 295 Set operation .........................................................................................................................
PAGE 11
Figures 1 Examples of syslog architecture ................................................................................. 22 2 Functions that generate audit log output ..................................................................... 23 3 Audit button ........................................................................................................... 24 4 Syslog tab ..............................................................................................................
PAGE 12
Tables 1 Audit log file components ........................................................................................ 29 2 Function names and event names output when audit log file is reproduced ..................... 30 3 Items in the audit log file .......................................................................................... 32 4 Symbols used in detailed information ......................................................................... 33 5 Items in the syslog file ...................
PAGE 13
33 Parameters for Delete Log operation .......................................................................... 79 34 Parameters for ORM Value operation ......................................................................... 80 35 Detailed information for ORM Value operation ........................................................... 80 36 Detailed information for SIM Complete operation ........................................................
PAGE 14
69 Detailed information for Install CV operation ............................................................ 108 70 Detailed information for Machine Install Date operation ............................................. 109 71 Detailed information for Make LUSE operation .......................................................... 109 72 Parameters for Make Vol./Vol. Init operation ............................................................ 110 73 Detailed information for Make Vol./Vol. Init operation .......
PAGE 15
105 Detailed information for Release Cache operation ..................................................... 135 106 Detailed information for Release Cache/CLPR operation ............................................ 136 107 Detailed information for Release LUN operation ........................................................ 136 108 Detailed information for Volume-Blockade operation .................................................. 137 109 Detailed information for Volume-Format operation ...................
PAGE 16
142 Values of option and host mode option .................................................................... 161 143 Detailed information for Set IP Address operation ...................................................... 162 144 Detailed information for Set iSNS operation ............................................................. 162 145 Detailed information for Set Security Switch operation ................................................ 163 146 Detailed information for Set Speed Mode operation ....
PAGE 17
9 Detailed information for Suspend Shredding operation .............................................. 197 180 Detailed information for Change Reserve operation ................................................... 199 181 Detailed information for Option operation ................................................................ 200 182 Detailed information for Pair Create operation .......................................................... 201 183 Detailed information for Pairresync operation ...............
PAGE 18
216 Detailed information for Pairsplit-r operation ............................................................. 234 217 Detailed information for Pairsplit-S operation ............................................................ 235 218 Detailed information for Add CTG operation ............................................................ 237 219 Detailed information for Add Pair operation .............................................................
PAGE 19
253 Detailed information for Add-Lu2 operation .............................................................. 271 254 Detailed information for Add-Wwn operation ........................................................... 273 255 Detailed information for Alternate-Path operation ....................................................... 273 256 Detailed information for Check-Paths operation ......................................................... 274 257 Detailed information for ChkPath-RestoreVol operation ..
PAGE 20
290 Audit log file output by program option button .......................................................... 312 291 LUN Manager operation and priority of audit log output ............................................
PAGE 21
1 Introduction This chapter introduces you to the audit logs created by XP Remote Web Console. It describes the purpose of the logs, how to download them, and descriptions of the audit logs. Introduction to audit log The practice of logging and log management using syslog has been used for many years, but using storage technology as part of the process is relatively new. The audit log function allows you to record the access, activity, and configuration changes made to your storage system.
PAGE 22
• In the United States, the Sarbanes-Oxley (SOX) Act establishes corporate accountability for all public companies, requiring strict IT controls and processes. Specifically, Sarbanes-Oxley requires companies to “Audit unauthorized access, misuse and fraud, in order to ensure the accuracy of corporate financial and business information” and “maintain financial records for seven years.
PAGE 23
itself with plugging into this infrastructure and then transmitting the log events. In addition to the syslog server, audit log also allows you to maintain a duplicate copy of the log inside the hard disk of the SVP as a backup. In the storage system, a log message is output to the audit log in two types of cases: • A configuration change that is made either from an XP Remote Web Console computer or the SVP. • Powering up and shutting down the storage system.
PAGE 24
NOTE: Only the storage administrator can download the audit log file, and the Audit Log Administrator role needs to be set to Modify or View. 1. Log on as a storage administrator and open the XP Remote Web Console's main pane. 2. Click the Audit button in the top right corner of the main pane: Figure 3 Audit button 3. • Audit:Normal displays when the number of saved lines in the audit log file is below the threshold.
PAGE 25
Figure 4 Syslog tab The Syslog tab has the following features: • Output to Primary Server allows you to specify whether to transfer the audit log to the syslog server. • Click Enable to transfer the audit log to the primary syslog server. • Click Disable if you do not want to transfer the audit log to the primary syslog server.
PAGE 26
• Output Detailed Information allows you to specify whether to transfer the detailed information as well as the audit log file. NOTE: This information is always maintained on the array, regardless of the settings made in this pane. • Click Enable to transfer the detailed information to the syslog server. • Click Disable to not transfer the detailed information to the syslog server. • Download Syslog allows you to download the syslog information file component to the XP Remote Web Console computer.
PAGE 27
4. Click the Audit Log tab to open the Audit Log pane. Figure 5 Audit Log tab 5. 6. Set the primary FTP server according to the following procedure: a. Click Enable in Output to Primary Server. b. Enter the IP address in the Primary Server Setting. You do not have to enter the periods. c. Enter the User ID and Password you use to login the primary FTP server. d. Enter the folder to which the audit log information file will be output.
PAGE 28
2. Click the Audit Log tab to open the Audit Log pane. 3. Click Transfer in the Audit Log pane. A message will display to indicate that the transfer has completed. NOTE: If you change the configuration in the Audit Log pane (when the items set in the pane are displayed in blue italic letters), click Apply to apply the configuration in the pane to the storage system, and then click Transfer.
PAGE 29
Description of the audit log file The audit log file includes the following components: Table 1 Audit log file components Component Login audit log file Settings audit log file Syslog information file File name login.log audit.log syslog.log AuditYYYYMMDD.tgz AuditYYYYMMDD.tgz syslogYYYYMMDD.tgz YYYY = year YYYY = year YYYY = year MM = month MM = month MM = month DD = day DD = day DD = day AuditSSSSSYYYYMMDDHHMMSS.tgz AuditSSSSSYYYYMMDDHHMMSS.
PAGE 30
Component Threshold Login audit log file Settings audit log file Once the information stored in the audit log information file reaches its maximum capacity, the starting line of the oldest data begins to be overwritten with the starting line of the newest data (wrap around). When you reach 70% of this threshold, the yellow Audit:Warning button displays on the XP Remote Web Console main pane.
PAGE 31
2 Audit log file format This chapter describes the three types of audit log file components. Login audit log file component The login audit log file component includes user ID, SLPR number, date, time, function, operation (login or logout), IP address, result, and serial number. Each item is separated by a comma (see Table 3 for a description of each item). The following figure shows an example.
PAGE 32
Figure 7 Settings audit log file component The audit log file includes the following items, listed in the following table: Table 3 Items in the audit log file Number Item Explanation User ID NOTE: 1 Login user ID When the operation name is AuditLog and the event name is Create File, system is output. SLPR number. For storage administrators, 99 displays. NOTE: 2 SLPR number Not output when the operation name is AuditLog and the event name is Create File.
PAGE 33
Number Item Explanation Login audit log file components display the IP address of the XP Remote Web Console (web client) computer used for logging on. No information is output for the logoff operation. 8 Parameters Settings audit log file components display parameters for certain functions, such as Modify for the ChangeMode operation. For some operations, such as Paircreate, parameters display as detailed information on the following line or lines.
PAGE 34
Syslog information file component The syslog information file component includes information from the login audit log file and settings audit log file components, including detailed information from the settings file. The following figure shows an example. Figure 8 Syslog audit log file The syslog files include the following items, listed in the following table. Table 5 Items in the syslog file No.
PAGE 35
No. Item Explanation 5 Unified specification identification information The Unified specification identification character (CELFSS). 6 7 8 Message identification information The revision number of the Unified specification document (1.1). The sequence number of the syslog header information. Message ID. Not displayed because it is not used. The date, time and the time difference between UTC (Coordinated Universal Time) in the format of YYYY-MM-DD-Thh:mm:ss.
PAGE 36
No. Item Explanation The location identification name set by the user in the Syslog pane. NOTE: 17 Related information See HP StorageWorks XP Remote Web Console User's Guide for more information. 18 FQDN. Not displayed because it is not used. 19 Redundant identification information. Not displayed because it is not used. 20 Agent information Not displayed because it is not used. 21 Host sending the request. Not displayed because it is not used. 22 Port sending the request.
PAGE 37
No. Item 30 Explanation The detailed information from the settings information file is displayed. For more information, see Table 2. Syslog information file monitoring threshold Only the function and event names are output to the syslog file and are described in the following table. Event names are output only once. NOTE: The information described in the following table is not output to the setting information file.
PAGE 38
Audit log file format
PAGE 39
3 Audit log functions, operations, and products This chapter provides a listing of the audit log functions and relationships to the XP Command View program products. It describes audit log functions and operations and includes sample audit logs. Audit Log functions and operations The following lists the audit log functions, operations, and program products.
PAGE 40
Function Name Operation Name Page Option Name Flex Copy XP Delete Pair 71 Flex Copy XP Pair Create 71 Attribute 73 Expiration Lock 74 Release All Extents 74 Retention-Term 75 VMA 76 Boot Management 77 LUN Security XP Extension ENAS LUN Security XP Extension NAS Blade Manager PCR of Cache Residency Manager Information Install 40 Set Cache Color 77 Delete Log 79 ORM Value 80 SIM Complete 81 SIM Reporting Option 81 Threshold Value 82 Add Host Group 85 Add iSCSI name
PAGE 41
Function Name Install Operation Name Page Change iSCSI Target 92 Change WWN 92 DCR Prestaging 93 Define Config. 93 Delete DKC WWN 94 Delete Host Group 94 Delete iSCSI name 95 Delete iSCSI Target 95 Delete LU Path 96 Delete WWN 97 DKU Emulation 97 Force Reset 98 Format 99 Format Stop 100 Init DKC iSCSI name 100 Initialize ORM Value 101 Install 101 Install CV 107 Machine Install Date 108 Make LUSE 109 Make Vol./Vol.
PAGE 42
Function Name On Demand LDEV LUNM 42 Operation Name Page Set Battery Life 117 Set Channel Speed 118 Set CommandDev 118 Set CommandDevSec 119 Set Fibre Address 120 Set Fibre Topology 120 Set Host Mode 121 Set IP Address 122 Set Security Switch 123 Set Speed Mode 123 Set Subsystem Time 124 System Option 125 System Tuning 127 Uninstall 129 Update Config 133 Volume to Space 134 Release Cache 135 Release Cache/CLPR 135 Release LUN 136 Volume-Blockade 137 Volume-Form
PAGE 43
Function Name Operation Name Page Add iSCSI Target 142 Add LU Path 143 Add WWN 143 Auth Info (Host) 144 Auth Info (Target) 145 Change Host Group 145 Change iSCSI name 146 Change iSCSI Target 147 Change WWN 147 Delete DKC WWN 148 Delete Host Group 149 Delete iSCSI name 149 Delete iSCSI Target 150 Delete LU Path 151 Delete WWN 151 Init DKC iSCSI name 152 Set Authentication 152 Set Channel Speed 153 Set CommandDev 153 Set CommandDevSec 154 Set FCSP Host 155 Set FCSP
PAGE 44
Function Name LUSE Maintenance PFM 44 Operation Name Page Set Host Mode 160 Set IP Address 161 Set iSNS 162 Set Security Switch 163 Set Speed Mode 163 Set TCP/IP Port 164 Make LUSE 165 Release LUSE 165 Blockade 167 Correction Copy 168 Drive Interrupt 168 Format 169 Format Stop 170 Recover 170 Replace 171 Restore 173 Restore Data 173 Size Change 174 Spare Disk 175 Switch SVP 175 Transfer Config 176 Type Change 176 Verify 177 Verify Stop 178 Monitoring S/
PAGE 45
Function Name Operation Name Page Option Name PORT Change Port 181 Changing port attribute operation from TrueCopy, TrueCopy for z/OS, Universal Replicator, Universal Replicator for z/OS, Serverless Backup Enabler, or Universal Volume Manager PP KEY File 183 License Key File Install 183 Install 184 Uninstall 184 Add Path 187 Add RCU 188 Change RCU Option 189 Delete Path 190 Delete RCU 191 Port-Group(Forced) 193 Port-Group(Normal) 193 End Shredding 195 Set Shredding 195 Su
PAGE 46
Function Name Operation Name Page Change Reserve 208 CTG 208 Delete Pair 209 Exp R_TBL(Disable) 210 Exp R_TBL(Enable) 210 Initialize 210 Option 211 Resync Pair 212 Set SCP Time 212 Split Pair 213 Suspend Pair 214 SNMP Set SNMP Agent 215 SNMP Information, SNMP Performance Control Change PPCGrp 217 HP Performance Control XP Clear PPC Info 217 Default Set 218 PPCGrp Del/Chg 218 Set All Prio Port 219 Set All Prio WWN 220 Set Ctrl Kind 220 Set Prio Port 221 Set Prio
PAGE 47
Function Name TC z/OS Continuous Access XP Journal Operation Name Page Change Async Option 228 Change CTG Option 228 Change Option 229 Change Pair Option 230 Delete CTG 231 Paircreate 231 Pairresync 233 Pairsplit-r 234 Pairsplit-S 235 Start Pair 236 Add CTG 237 Add Pair 238 Change Async Option 239 Change CTG Option 240 Change Option 241 Change Pair Option 241 Clear SIM 242 Delete Cmd Dev 243 Delete CTG 243 Delete Pair 244 Resume Pair 245 Script Operation 246
PAGE 48
Function Name UR z/OS External Storage XP 48 Operation Name Page Journal-Vol 250 Journal-Vol 251 Paircreate 252 Pairresync 253 Pairsplit-r 254 Pairsplit-S 255 Pair-Option 256 System-Option 257 Add-Pair 259 Clear-SIM 260 Delete-Pair 260 Edit-EXCTG 261 Journal-Option 262 Journal-Vol 264 Journal-Vol 265 Pair-Option 265 Resume-Pair 266 Suspend-Pair 267 System-Option 268 Add-Lu2 271 Add-Wwn 272 Alternate-Path 273 Check-Paths 274 ChkPath-RestoreVol 275 Delete-
PAGE 49
Function Name Operation Name Page Disconnect-Paths 277 Disconnect Volume 278 WwnTimer 278 Install CV 281 Make Volume 282 Set SSID 283 Volume Initialize 284 Volume to Space 285 Create Auto Plan 287 Del Auto Plan Log 287 Delete Auto Plan 287 Del Migration Log 288 Set Auto Plan Param 288 Set Class Threshold 289 Set Fixed PG 290 Set Migration Vol 291 Set Plan Condition 292 Set Reserved Vol 293 HP Disk/Cache Partition Set 295 Virtual Partition Manager VRM Attribute 29
PAGE 50
Function Name XRCR Operation Name Page Pool Change/Delete 302 Pool Initialize 303 Pool Restore 304 Pool SIM Comp Req 304 Set Pool 305 Set XRC Option 307 Option Name Compatible Replication for IBM XRC Sample audit logs Sections “Audit Log function” on page 53 through “XRCR function” on page 307 contain sample audit logs for each function and operation performed by XP Remote Web Console. The individual items in each sample log are described, starting with function name.
PAGE 51
HH:MM:SS:xxx Hour, minute and millisecond audit log was created (HH:MM:SS:000). 00.00 Time difference in hours and minutes between Universal Time and local time (± HH:MM). Acronyms in examples In some output examples, acronyms are used to refer to the product names. For example, in the “Virtual LVI / Virtual LUN (VLL) function” on page 281, under the “Install Customized Volume (CV) operation” on page 281 VLL refers to LUN Configuration Manager XP (see Figure 11).
PAGE 52
Audit log functions, operations, and products
PAGE 53
4 Audit Log function Create File This information is output to the login information file, the setting information file, and the syslog information file components. See “Audit log file output” on page 30. Example 1 (Login information file component) ,,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[AuditLog],Create File,LoginLog,Warning,Seq.=xxxxx Example 2 (Setting information file component) ,,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[AuditLog],Create File,AuditLog,Warning,Seq.
PAGE 54
The operation has ended normally. Over Threshold event <14> Jan 4 06:25:18 SVP Storage: CELFSS,1.1,250001,,2006-01-04T06:25:18.3Z,Storage,SVP, AnomalyEvent,Success,,R500:65307,,Japan-Tokyo,,,,,,,,,,,,,[AuditLog],Over Threshold,,Normal end This information is displayed in the Syslog Information file component only. No parameters display for this event. [Audit Log] Audit Log function Over Threshold Over Threshold event Normal end The operation has ended normally.
PAGE 55
Item Description Whether to transfer the settings audit log file component (audit.log) to the FTP server. OutFlg Enable: Transfer settings audit log file component. Disable: Do not settings audit log file component. SrvAddr The IP address to which the settings audit log file component is sent. A hyphen (-) is displayed if you do not change the setting. UserName The user name to login to the FTP server. A hyphen (-) is displayed if you do not change the setting.
PAGE 56
NOTE: The detailed information is not displayed if you do not change settings. Table 12 Detailed information for Set Syslog Server operation Item Description DetailFlg Locationinfo ServerType IPAddrVer Indicates whether to output detailed information to the syslog server. Enable: Output detailed information. Disable: Do not output detailed information. The location identification information of the storage system. The syslog server to which syslog information is output. Primary: Primary syslog server.
PAGE 57
Detailed information for this operation is shown in the following table. Table 13 Detailed information for Set Syslog Server operation Item Description Reference Code The SIM reference code of the error and service request. Num. of Reference Codes The number of SIM reference codes.
PAGE 58
Audit Log function
PAGE 59
5 Account function Set User Account operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[Account],Set User Account,,Normal end, Seq=xxxxx +Operation=Change +{UserID,Authority,SLPRNo,WritePermission,ReadPermission}=-[{use001,Administrator,65535, FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF,-},{use002,User,1,-,-}] Num.
PAGE 60
Item Description Num of Users The number of users.
PAGE 61
6 BASE function ChangeMode operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[Base],ChangeMode,Modify,Normal end,Seq.=xxxxxx [Base] BASE function ChangeMode ChangeMode operation Modify Modify is the selected parameter. This operation uses the following parameters, as shown in the following table.
PAGE 62
Set System Info Set System Information operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 16 Detailed information for Set System Info operation Item Description Name Nickname of the device Contact Name of the system administrator. Location Installation location of the device. Num of SystemInfo Number of system information.
PAGE 63
7 Cache function DCR Prestaging operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Cache],DCR Prestaging,, Normal end,Seq.=xxxxx [Cache] Cache function DCR Prestaging DCR Prestaging operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Delete M/F DCR operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[Cache],Delete M/F DCR,,Normal end,Seq.
PAGE 64
Item Description Start CC-HH The starting cylinder number (CC) and the starting head number (HH) of the cancelled data. End CC-HH The ending cylinder number (CC) and the ending head number (HH). This number is output when the ending cylinder and ending head are specified for the cancelled data. Num. of LDEVs The number of logical volumes (for a mainframe system) where the setting information of Cache Residency cache was cancelled.
PAGE 65
[Cache] Cache function Set M/F DCR Set M/F DCR operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 19 Detailed information for Set M/F DCR operation Item Description CU:LDEV The CU and LDEV numbers of the logical volume (for a mainframe system) where the setting information of Cache Residency cache is added or changed.
PAGE 66
Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 20 Detailed information for Set Open DCR operation Item Description CU:LDEV The CU and LDEV numbers of the logical volume (for a mainframe system) where the setting information of Cache Residency cache was added or changed. The setting mode of Cache Residency cache. Mode Bind: Bind, Priority: Priority The prestaging target.
PAGE 67
8 CFL function LUNM operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[CFL],LUNM Operation,Start,Normal end,Seq.=xxxxxx +{Operation, Sheet Name}={LUNM,ADT_1.CSV} Num of Sheets=1 [CFL] CFL function LUNM Operation LUNM operation Start Start is the selected parameter. The Start parameter is the start of the CFL, The End parameter is the end of the CFL. Normal end The operation has ended normally. Seq.
PAGE 68
CFL function
PAGE 69
9 CPAV function Add Alias operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[CPAV],Add Alias,,Normal end,Seq.=xxxxx +CU=0x00 ++{Alias LDEV,Base LDEV}=[{0xFD,0x00},{0xFE,0x00},{0xFF,0x01}],Num. of Alias LDEVs=3 +CU=0x01 ++{Alias LDEV,Base LDEV}=[{0xFF,0x00}],Num. of Alias LDEVs=1 +Num. of Alias LDEVs=4 [CPAV] CPAV function Add Alias Add Alias operation Normal end The operation has ended normally. Seq.
PAGE 70
++{Alias LDEV,Base LDEV}=[{0xFD,0x00},{0xFE,0x00},{0xFF,0x01}],Num. of Alias LDEVs=3 +CU=0x01 ++{Alias LDEV,Base LDEV}=[{0xFF,0x00}],Num. of Alias LDEVs=1 +Num. of Alias LDEVs=4 [CPAV] Compatible PAV for IBM z/OS function Delete Alias Delete Alias operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 71
10 Flex Copy XP function Delete Pair operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[FC],Delete Pair,,Normal end,Seq.=xxxxx +{P-VOL(CU:LDEV),S-VOL(CU:LDEV),Result}=[{0xAA:0xBB,0xCC:0xDD,Normal end}, {0xAA:0xBB,0xCC:0xDD,Error(xxxx-yyyy)}],Num. of Pairs=2 [FC] Flex Copy function Delete Pair Delete Pair operation Normal end The operation has ended normally. Seq.
PAGE 72
Flex Copy function Pair Create Pair Create operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 25 Detailed information for Pair Create operation Item Description Copy Pace Copy Type The set copy speed. Faster: high speed, Medium: medium speed, Slow: slow speed The set copy type.
PAGE 73
11 LUN Security XP Extension function Attribute operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LSE],Attribute,,Normal end,Seq.=xxxxx +{CU:LDEV,Attribute,Result}=[{0x00:0x01,0x80,Normal end},{0x00:0x02,0x82,Error(9605-8122)}, {0x00:0x03,0x81,Normal end},{0x00:0x03,0x81,Normal end}],Num. of LDEVs=XXX [LSE] LUN Security Extension function Attribute Attribute operation Normal end The operation has ended normally. Seq.
PAGE 74
Item Description Num. of LDEVs The number of the logical volume(s) where the attribute has been set. * When bit 5, 6, and 7 are all 0 (zero), Read/Write has been set. Expiration Lock operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[LSE],Expiration Lock,SLPR#xx:Enable, Normal end,Seq.=xxxxx [LSE] LUN Security Extension function Expiration Lock Expiration Lock operation SLPR#xx:Enable SLPR#xx: Enable is selected as the parameter.
PAGE 75
Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 28 Detailed information for Release All Extents operation Item Description CU:LDEV The CU number and the LDEV number of the volume where the Extent operation is executed. Operation The content of the operation. 0x80: Delete Extent The result of the operation.
PAGE 76
Item Description The result of operation. Normal end: Normal end Result Error(xxxx-yyyyy): Abnormal end xxxx: Part codeyyyyy: Error code Num. of LDEVs The number of the volumes where the Extent operation is executed. VMA operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00, [LSE],VMA,,Normal end,Seq.=xxxxx +{CU:LDEV,Result}=[{0x00:0x01,Normal end},{0x00:0x02,Error(9605-8122)},{0x00:0x03,Normal end}, {0x00:0x03,Normal end},{0x00:0x03,Normal end}],Num.
PAGE 77
12 ENAS function Boot Management operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[ENAS],Boot Management,,Normal end,Seq.=xxxxx +{CHN,Operation}=[{CHA-1E,Shutdown},{CHA-2Q,Boot},{CHA-1F,Reboot},{CHA-2R,Shutdown}, {CHA-1G,Boot},{CHA-2T,Reboot},{CHA-1H,Shutdown},{CHA-2U,Boot}, -{CHA-1A,Reboot},{CHA-2M,Shutdown},{CHA-1B,Boot},{CHA-2N,Reboot},{CHA-1L,Shutdown}, {CHA-2X,Boot},{CHA-1K,Reboot},{CHA-2W,Shutdown}],Num.
PAGE 78
[ENAS] Network Area Storage function Set Cache Color Set Cache Color operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 32 Detailed information for Set Cache Color operation Item Description CLPR The Cache Logical Partition (CLPR) number. This number is output when CLPR is used only.
PAGE 79
13 Information function Delete Log operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xx, 00:00,[Information],Delete Log,SIM,Normal end, Seq.=xxxxx [Information] Information Function Delete Log Delete Log operation SIM SIM is the selected parameter. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) This operation uses the following parameters, as shown in the following table.
PAGE 80
ORM Value operation Example 1 (Changing the threshold) user-name,xx,YYYY/MM/DD,HH:MM:SS:xx, 00:00,[Information],ORM Value,Alter,Normal end, Seq.=xxxxx +Type=7days ++PDEV=[HDDR00-01,HDDR00-02,(snip)],Num. of PDEVs=1152 Example 2 (Error Reset) user-name,xx,YYYY/MM/DD,HH:MM:SS:xx, 00:00,[Information],ORM Value,Error Reset,Normal end, Seq.
PAGE 81
SIM Complete operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xx, 00:00,[Information],SIM Complete,,Normal end, Seq.=xxxxx +Reference Code=[XXXXXX,XXXXXX,(snip)],Num. of Reference Codes=256 [Information] Information function SIM Complete Service Information Message (SIM) Complete operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table.
PAGE 82
Detailed Information Detailed information displays for this operation, as shown in the following table. Table 37 Detailed information for SIM Reporting Option operation Item Description The type of SIM. Type DKC SIM: SIM related to storage system, Cache SIM: SIM related to cache, Media SIM: SIM related to recording media, Device SIM: SIM related to disk device Report acute level information as SIM. Acute ON: Report, OFF: Do not report Serious Moderate Service Num.
PAGE 83
Alter is the selected parameter for example 1 and Error Reset is the selected parameter for example 2. This operation uses the following parameters, as shown in the following table. Table 38 Alter and Error Reset Parameters for Threshold Value operation Parameter Description Alter Change the threshold of failed PDEV (physical device). Error Reset Indicates Error Reset. Normal end The operation has ended normally. Seq.
PAGE 84
Information function
PAGE 85
14 Install function Add Host Group operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Add Host Group,,Normal end,Seq.=xxxxx +{Port,HostGrpID,HostGrpName,Mode,Option}={XX,0xXXX,XXXXXXXXXXXXXXXX,0xXX,0xXXXXXXXX} ++{WWN,Nickname}=[{0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX},{0xXXXXXXXXXXXXXXXX, XXXXXXXXXXXXXXXX}],Num. of WWNs=2 +{Port,HostGrpID,HostGrpName,Mode,Option}={XX,0xXXX,XXXXXXXXXXXXXXXX,0xXX,0xXXXXXXXX} +Num.
PAGE 86
Add iSCSI Name operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Add iSCSI name,,Normal end,Seq.=xxxxx +{Port,HostGrpID,iSCSI name,Name}=[{1E,0x01,iqn.xxxxxxxxxxxxxxxxxxxx,aaaaaaaaaa}, {3E,0x01,iqn.yyyyyyyyyyyyyyyyyyyy,bbbbbbbbbb}],Num. of iSCSI names=2 [Install] Install function Add iSCSI name Add iSCSI name operation Normal end The operation has ended normally. Seq.
PAGE 87
Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 42 Detailed information for Add iSCSI Target operation Item Description Port The name of the port where the iSCSI Target has been added. HostGrpID The host group number where the iSCSI Target has been added. Target name The iSCSI Target name added. Alias The alias of the iSCSI Target name added. Mode The host mode set.
PAGE 88
Item Description LUN Indicates LUN of the logical volume linked to the host group. CU:LDEV The CU and LDEV numbers of the logical volume linked to the host group. Num. of Paths The number of LU paths set. Add WWN operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Add WWN,,Normal end,Seq.=xxxxx +{Port,HostGrpID,WWN,Nickname }=[{XX,0xXXX,0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}, {XX,0xXXX,0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}],Num.
PAGE 89
All Config operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 45 Detailed information for All Config operation Item Description Old Ver. The old version number of the configuration information. New Ver. The new version number of the configuration information.
PAGE 90
Install function Backup Backup operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Backup Config operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,GMT,[Install],Backup Config,,Normal end,Seq.=xxxxx +Ver.=xx-xx-xx/xx [Install] Install function Backup Config Backup Config operation Normal end The operation has ended normally. Seq.
PAGE 91
Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 48 Detailed information for Change Host Group operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number where the name or host modes have been changed. HostGrpName The name of the host group. If the name is changed, the name after change is indicated. Num.
PAGE 92
Change iSCSI Target operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Change iSCSI Target,,Normal end, Seq.=xxxxx +{Port,HostGrpID,Target name,Alias}=[{1E,0x05,iqn.xxxxxxxxxxxxxxxxxxxx,aaaaaaaaaa}, {3E,0x05,iqn.yyyyyyyyyyyyyyyyyyyy,bbbbbbbbbb}],Num. of iSCSI Targets=2 [Install] Install function Change iSCSI Target Change iSCSI Target operation Normal end The operation has ended normally. Seq.
PAGE 93
Detailed Information Detailed information displays for this operation, as shown in the following table. Table 51 Detailed information for Change WWN operation Item Description Port The name of the port where the host is connected. HostGrpID The host group number on which the host with WWN or nickname of the host bus adapter being changed is registered. WWN Indicates WWN of the host bus adapter before change. Change WWN Indicates WWN of the host bus adapter after change.
PAGE 94
Delete DKC WWN operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Delete DKC WWN,,Normal end,Seq.=xxxxx +{Port,Delete WWN}=[{XX,0xXXXXXXXXXXXXXXXX},{XX,0xXXXXXXXXXXXXXXXX}],Num. of WWNs=2 [Install] Install function Delete DKC WWN Delete Disk Controller (DKC) World Wide Name (WWN) operation Normal end The operation has ended normally. Seq.
PAGE 95
Detailed information displays for this operation, as shown in the following table. Table 53 Detailed information for Delete Host Group operation Item Description Port The name of the port where the host group deleted or initialized was created. HostGrpID The host group number deleted or initialized. Num. of Host Groups The number of host groups deleted or initialized. Delete iSCSI Name operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Delete iSCSI name,,Normal end, Seq.
PAGE 96
Delete iSCSI Target Delete iSCSI Target operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 55 Detailed information for Delete iSCSI Target operation Item Description Port The name of the port where the iSCSI Target has been deleted. HostGrpID The host group number where the iSCSI Target has been deleted. Num.
PAGE 97
Item Description Num. of Paths The number of LU paths deleted. Delete WWN operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Delete WWN,,Normal end,Seq.=xxxxx +{Port,HostGrpID,WWN}=[{XX,0xXXX,0xXXXXXXXXXXXXXXXX},{XX,0xXXX,0xXXXXXXXXXXXXXXXX}], Num. of WWNs=2 [Install] Install function Delete WWN Delete World Wide Name (WWN) operation Normal end The operation has ended normally. Seq.
PAGE 98
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 58 Detailed information for DKU Emulation operation Item Description Type The emulation type. LDEV(CU:LDEV) The CU and LDEV numbers where the emulation type is changed. Num. of LDEVs The number of logical volumes where the emulation type is changed. Num.
PAGE 99
Format operation NOTE: This log information indicates the completion of Format operation and does not indicate the completion of Format processing. The Format processing requires some time. The status of the LDEV will change when the Format Processing is completed. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Format,,Normal end,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num. of PGs=1 –> in case of an external volume +PG=[V1-1],Num. of PGs=1 –> in case of a vertual volume +LDEV=[0x00-0x01],Num.
PAGE 100
Format Stop operation NOTE: This log information is output when the format process is suspended. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Format Stop,,Normal end,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num. of PGs=1 –> in case of an external volume +PG=[V1-1],Num. of PGs=1 –> in case of a virtual volume +LDEV=[0x00-0x01],Num. of LDEVs=1 [Install] Install function Format Stop Format Stop operation Normal end The operation has ended normally. Seq.
PAGE 101
Seq.=xxxxxx Sequence number of log information (000000 to 999999) Initialize ORM Value operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Initialize ORM Value,,Normal end, Seq.=xxxxx [Install] Install function Initialize ORM Value Initialize Online Read Margin (ORM) Value operation Normal end The operation has ended normally. Seq.
PAGE 102
Install Install operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 62 Detailed information for Install operation (installing additional channel adapters) Item Description Channel Adapter (CHA) The channel adapter (CHA). mounting location. Kind The kind of PCB mounted.
PAGE 103
+Num. of PGs=3 ++{B4,SPARE,Dreve Type}={1,1,DKR2F-J300FC},Num. of SPAREs=1 [Install] Install function Install Install operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table.
PAGE 104
Item Description Num. of PGs The number of parity groups. B4 The B4 number. SPARE The spare drive number. Num. of SPAREs The number of spare drives. NOTE: Only the changed items will be output. In the recovery process, the detailed information of the process is not output when the setting of the installation before the process has completed. However, the setting of the recovery process is output as the detailed information when the setting of the installation before the process has not completed.
PAGE 105
Item Description DCR available size The capacity of Cache Residency. PCR available size The capacity of PCR. CLPR The CLPR number. Cache size The capacity of the cache memory allocated to CLPR. DCR size The capacity of Cache Residency allocated to CLPR. Extent Number The number of extents allocated to CLPR. PCR size The capacity of the PCR allocated to CLPR. Num. of CLPRs The number of CLPR. SM The mounting location of the shared memory.
PAGE 106
Detailed information displays for this operation, as shown in the following table. Table 65 Detailed information for Install operation (installing additional shared memory) Item Description SM The mounting location of the PCB for shared memory. Slot The slot position of the shared memory module. Size The capacity of the cache memory module. Num of SMMs The number of shared memory modules. PP Flag The option flags. Num of PP Flags The number of option flags. VFS SYS Area The area of VFS SYS.
PAGE 107
Detailed information displays for this operation, as shown in the following table. Table 66 Detailed information for Install operation (installing additional power supply) Item Redundant Description The status of additional cluster power supply. EQUIP: Installed, NOT EQUIP: Not installed. Example 6 (Installing additional battery) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Install,,Normal end,Seq.=xxxxx +Battery=[BATTERY13/BATTERY23],Num.
PAGE 108
No parameter is selected. This operation uses the following parameters, as shown in the following table. Table 68 Parameters for Install CV operation Parameter Description No parameter Formatted Install CV. Non Format Unformatted Install CV. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information If enabled, detailed information displays for this operation, as shown in the following table.
PAGE 109
Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 70 Detailed information for Machine Install Date operation Item Description Date Indicates the date and the time of the setting in YYYY/MM/DD HH: mm format (YYYY: year, MM: month, DD: day, HH: hour, mm: minute). Make LUSE operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Make LUSE,,Normal end,Seq.
PAGE 110
Make Vol./Vol. Init operation No parameter or Non Format No parameter is selected. This operation uses the following parameters, as shown in the following table. Table 72 Parameters for Make Vol./Vol. Init operation Parameter Description No parameter Formatted Make Volume or Volume Initialize. Non Format Unformatted Make Volume or Volume Initialize. Normal end The operation has ended normally. Seq.
PAGE 111
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 74 Detailed information for Micro Program operation Item Description Micro Media The media which the microprogram to be exchanged is stored (Floppy disk, CDROM, SVP HDD, HDD Backup or remote transfer). Exchange How The method to exchange the microprogram.
PAGE 112
Detailed information displays for this operation, as shown in the following table. Table 75 Detailed information for MP Install operation Item Description Micro Program The kind of microprogram installed (Minimum Config, DKCMAIN, RAMBOOT, LCP, HTP, LCDG, FCDG, PCDG, or NASBIOS). Num. of Kind The number of the kind of the installed microprogram. Target MP The mounting location of the installed microprogram. Num. of MP The number of microprogram installed.
PAGE 113
Item Description End CC-HH The ending cylinder number (CC) and the ending head number (HH) which the Cache Residency is set or canceled. Num of DCR Settings The number of Cache Residency which has been set or canceled. New Installation operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,GMT,[Install],New Installation,,Normal end,Seq.=xxxxx +Micro Program={Minimum Config,DKCMAIN,RAMBOOT,LCP,HTP,LCDG,FCDG,PCDG,NASBIOS}, Num.
PAGE 114
Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 78 Detailed information for Open DCR operation Item Description CU:LDEV The CU number and the LDEV number of the logical volume (for an open system) where Cache Residency is set. The setting status of Cache Residency. Define Set: set, Delete: cancel The setting mode of Cache Residency. Indicates a dash (-) when Define is Delete.
PAGE 115
Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 79 Detailed information for Patch Edit operation Item Description Block The block number. File Entry Ctl. The file information. Old: old data, New: new data. The entry number. The control information. 00: Invalid, 20: End in sector, 40: End of patch, 80: Valid Address The address. Old Data The old data. New Data The new data.
PAGE 116
Detailed information displays for this operation, as shown in the following table. Table 80 Detailed information for Release LUSE operation Item Description LUSE(CU:LDEV) The CU and LDEV numbers of several LDEVs that were combined into the released LUSE volume. The number indicated at the beginning represents the CU and LDEV numbers of the top LDEV. Num. of LUSEs The number of LUSE volumes released. Restore operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Restore,,Normal end,Seq.
PAGE 117
user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Restore Config.,,Normal end, Seq.=xxxxx +{Old Ver.,New Ver.}={xx-xx-xx/xx,xx-xx-xx/xx} [Install] Install function Restore Config. Restore Config. operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 81 Detailed information for Restore Config.
PAGE 118
Item Description Date Indicates the date of the setting in YYYY/MM/DD format (YYYY: year, MM: month, DD: day). A hyphen (-) is indicated when the information is not set. Remained Life The remaining date of the battery shelf life. A hyphen (-) is indicated when the information is not set. Set Channel Speed operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Set Channel Speed,,Normal end, Seq.=xxxxx +{Port,Speed(Gbps)}=[{XX,1},{XX,2},{XX,Auto}],Num.
PAGE 119
The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 84 Detailed information for Set CommandDev operation Item Description CU:LDEV The CU and LDEV numbers of the logical volume where the command device is set. CommandDev Num. of LDEVs Indicates whether the command device setting is enabled or disabled. Disable or Enable is output.
PAGE 120
Set Fibre Address operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Set Fibre Address,,Normal end, Seq.=xxxxx +{Port,Fibre Addr.}=[{XX,1},{XX,126}],Num. of Ports=2 [Install] Install function Set Fibre Address Set Fibre Address operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table.
PAGE 121
Detailed information displays for this operation, as shown in the following table. Table 87 Detailed information for Set Fibre Topology operation Item Description Port The name of the port where the topology of Fibre Channel is set. Fabric Connection Num. of Ports Indicates whether the Fabric switch is enabled or disabled. Enable: Enabled, Disable: Disabled The connecting mode of the Fabric switch selected.
PAGE 122
Set IP Address operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Set IP Address,SVP&DKC,Normal end, Seq.=xxxxx +{IPAdd,Subnet,Use Duplex,SVP Kind,M-SVP IPAdd,M-SVP Sunbet,S-SVP IPAdd,S-SVP Subnet}= {(123.456.789.123),(255.255.255.255),Valid,Master SVP,(111.222.333.444),(255.255.255.255), (555.666.777.888),(255.255.255.255)} [Install] Install function Set IP Address Set IP Address operation SVP&DKC SVP&DKC is the selected parameter.
PAGE 123
Item Description S-SVP Subnet The subnet mask of Standby SVP. Set Security Switch operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Set Security Switch,,Normal end, Seq.=xxxxx +{Port,Switch}=[{XX,Disable},{XX,Enable}],Num. of Ports=2 [Install] Install function Set Security Switch Set Security Switch operation Normal end The operation has ended normally. Seq.
PAGE 124
Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 92 Detailed information for Set Speed Mode operation Item Description Channel Adapter (CHA) The Channel Adapter (CHA) name (name of channel adapter). Port Block The port block. Port blocks A, B, C, and D are output in case of a 16-port channel adapter. In case of an 8-port channel adapter, port blocks A and B are output.
PAGE 125
TOD Change is the selected parameter for example 1, Synchro. Infor is the selected parameter for example 2, and NAS Time Zone is selected for example 3. This operation uses the following parameters, as shown in the following table. Table 93 Parameters for Set Subsystem Time operation Parameter Description TOD Change The date and the time. Synchro. Infor. The setting of time correction function. NAS Time Zone The time zone of NAS PCB. Normal end The operation has ended normally. Seq.
PAGE 126
+{LPR,Mode,Set}=[{System,154,ON},{LPR00,165,OFF}],Num of Modes=2 +Debug Mode=Set [Install] Install function System Option System Option operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 95 Detailed information for System Option operation Item Description Indicates the setting status of Spare Disk Recover.
PAGE 127
Item Description Power Supply Type The type of AC-BOX. Disk Unit (DKU) The DKU mounting location. AC-BOX The type of AC-BOX. Num. of AC-BOXs The number of AC-BOX. PDU The type of PDU. Num. of PDUs The number of PDUs. CU: LDEV The CU and LDEV numbers. Indicates the setting status of Destage. Destage ON: Execute write through operation (report the completion of the writing to the host after the writing to the disk drive has completed).
PAGE 128
+{Port,CU Number,Emulation}=[{1E,00-3F,I-2105-F20},{3E,-,I-2105-F20}, {5E,00-3F,I-2105-F20}],Num of Ports=3 +{CU,LDEV,SSID}={0x00,0x00-0xFF,0x0004},Num of SSIDs=1 [Install] Install function System Tuning System tuning operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table.
PAGE 129
Item Description Num of SSIDs The number of storage system IDs. Uninstall operation Example 1 (Uninstalling a channel adapter (CHA)) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Install],Uninstall,,Normal end,Seq.=xxxxx +{CHA,Kind}=[{CHA-1A,32HS Fibre 16ch-8mp},{CHA-2M,32HS Fibre 16ch-8mp}],Num of CHAs=2 [Install] Uninstall operation Normal end The operation has ended normally. Seq.
PAGE 130
Detailed information displays for this operation, as shown in the following table. Table 98 Detailed information for Uninstall operation (uninstalling a DKA, ECC group, or LDEV) Item Description Disk Adapter (DKA) The DKA mounting location. Num. of Disk Adapter (DKA)s The number of DKAs. Disk Unit (DKU) The DKU mounting location. Num. of Disk Unit (DKU)s The number of DKUs. FSW The fibre switch mounting location. Num. of FSWs The number of fibre switches. PG The parity group number. Num.
PAGE 131
Detailed information displays for this operation, as shown in the following table. Table 99 Detailed information for Uninstall operation (uninstalling a cache memory module) Item Description CM The mounting location of the PCB for cache memory. CMG The capacity of CMG. Size The capacity of cache memory. On-Demand The capacity of On-Demand. Num. of CMs The number of cache memory. DCR available size The capacity of Cache Residency. PCR available size The capacity of PCR. CLPR The CLPR number.
PAGE 132
[Install] Install function Uninstall Uninstall operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 100 Detailed information for Uninstall operation (uninstalling a shared memory module) Item Description SM The mounting location of the PCB for shared memory. Slot The slot position of the shared memory module.
PAGE 133
Uninstall operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 101 Detailed information for Uninstall operation (uninstalling a power supply) Item Redundant Description The status of additional cluster power supply. EQUIP: Installed, NOT EQUIP: Not installed.
PAGE 134
Update Config Update Config operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 103 Detailed information Update Config operation Item Description Old Ver. The old version number of the configuration information. New Ver. The new version number of the configuration information.
PAGE 135
15 On Demand function Release Cache operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[OND],Release Cache,,Normal end,Seq.=xxxxx +Cache(MB)=258048 [OND] On Demand function Release Cache Release Cache operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 136
Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 106 Detailed information for Release Cache/CLPR operation Item Description Cache(MB) The capacity of the cache memory cancelled. The unit is megabyte (MB). CLPR The CLPR number. Cache(MB) The capacity of the cache memory assigned to CLPR. The unit is megabyte (MB). Num. of CLPRs The number of CLPRs that expansion of cache memory is set.
PAGE 137
16 Logical Device (LDEV) function Volume-Blockade operation NOTE: This log information indicates the completion of Format operation and does not indicate the completion of Format process. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LDEV],Volume-Blockade,,Normal end,Seq.=xxxxx +CU:LDEV=[0x00:0x01,0x00:0x02,0x00:0x03,0x00:0x04,0x00:0x05,0x00:0x06,0x00:0x07,0x00:0x08, 0x00:0x09,0x00:0x0A],Num.
PAGE 138
Volume-Format operation This log information indicates the completion of Format operation and does not indicate the completion of Format processing. The Format processing requires some time. The status of the LDEV will change when the Format Processing is completed. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LDEV],Volume-Format,,Normal end,Seq.=xxxxx +CU:LDEV=[0x00:0x01,0x00:0x02,0x00:0x03,0x00:0x04,0x00:0x05,0x00:0x06,0x00:0x07,0x00:0x08, 0x00:0x09,0x00:0x0A],Num.
PAGE 139
Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 110 Detailed information for Volume-Format (H) operation Item Description CU:LDEV The CU number and the LDEV number. Num. of LDEVs The number of LDEVs being set. NOTE: The status does not change immediately after you execute an LDEV operation command. As a result, errors may occur after you execute the command.
PAGE 140
[LDEV] Logical Device function Volume-Restore(N) Volume Restore(N) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 112 Detailed information for Volume-Format (N) operation Item Description CU:LDEV The CU number and the LDEV number. Num. of LDEVs The number of LDEVs being set.
PAGE 141
17 LUN Manager (LUNM) function Add Host Group operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[LUNM],Add Host Group,,Normal end,Seq.=xxxxx +{Port,HostGrpID,HostGrpName}=[{XX,0xXXX,XXXXXXXXXXXXXXXX},{XX,0xXXX,XXXXXXXXXXXXXXXX}], Num.of Host Groups=2 [LUMN] LUN Manager function Add Host Group Add Host Group operation Normal end The operation has ended normally. Seq.
PAGE 142
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 114 Detailed information for Add iSCSI Name operation Item Description Port The name of the port where the host group has been added. HostGrpID The host group number newly added. iSCSI Name The iSCSI Name added. Name The iSCSI nickname added. Num.
PAGE 143
Item Description Num. of iSCSI Target The number of iSCSI Target added. Add LU Path operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Add LU Path,,Normal end,Seq.=xxxxx +{Port,HostGrpID,LUN,CU:LDEV}=[{XX,0xXXX,XX,0xXX:0xXX},{XX,0xXXX,XX,0xXX:0xXX}, {XX,0xXXX,XX,0xXX:0xXX}],Num. of Paths=3 [LUNM] LUN Manager function Add LU Path Add Logical Unit (LU) Path operation Normal end The operation has ended normally. Seq.
PAGE 144
Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 117 Detailed information for Add WWN operation Item Description Port The name of the port where the host group has been added. HostGrpID The host group number newly added. WWN Indicates WWN of the host bus adapter for the host registered in the host group. WWN is a 16-digit number in the hexadecimal format.
PAGE 145
Item Description UserName The user name where user authentication information has been set. The user name before change is indicated when Kind is set to Change. Change UserName The user name after change is indicated when Kind is set to Change. A hyphen () is indicated when Kind is set to Add or delete. Protocol The authentication type which is CHAP (Challenge Handshake Authentication Protocol). Num. of Info The number of user authentication information set.
PAGE 146
LUN Manager function Change Host Group Change Host Group operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 120 Detailed information for Change Host Group operation Item Description Port The name of the port where the host group is created. HostGrpID The host group number where the name or host modes have been changed.
PAGE 147
Item Description iSCSI name The iSCSI name before change. Change iSCSI name The iSCSI name after change. Name The iSCSI nickname after change. Num. of iSCSI name The number of iSCSI name changed. Change iSCSI Target operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[LUNM],Change iSCSI Target,,Normal end,Seq.=xxxxx +{Port,HostGrpID,Target name,Alias}=[{1E,0x05,iqn.xxxxxxxxxxxxxxxxxxxx,aaaaaaaaaa}, {3E,0x05,iqn.yyyyyyyyyyyyyyyyyyyy,bbbbbbbbbb}],Num.
PAGE 148
LUN Manager function Change WWN Change World Wide Name (WWN) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 123 Detailed information for Change WWN operation Item Description Port The name of the port where the host is connected.
PAGE 149
Detailed information for this operation is shown in the following table. Table 124 Detailed information for Delete DKC WWN operation Item Description Port The port name where the host of WWN deleted from WWN list was connected. Delete WWN Indicates WWN deleted from WWN list. WWN is a 16-digit number in the hexadecimal format. Num. of WWNs The number of WWNs deleted. Delete Host Group operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Delete Host Group,,Normal end,Seq.
PAGE 150
Delete iSCSI name Delete iSCSI name operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 126 Detailed information for Delete iSCSI name operation Item Description Port The name of the port where the iSCSI name has been deleted. HostGrpID The host group number where the iSCSI name has been deleted. iSCSI name The iSCSI name deleted. Num.
PAGE 151
Delete LU Path operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Delete LU Path,,Normal end,Seq.=xxxxx +{Port,HostGrpID,LUN}=[{XX,0xXXX,XX},{XX,0xXXX,XX},{XX,0xXXX,XX}],Num.of Paths=3 [LUNM] LUN Manager function Delete LU Path Delete Logical Unit (LU) Path operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 152
Detailed information for this operation is shown in the following table. Table 129 Detailed information for Delete WWN operation Item Description Port The name of the port where the host deleted from host group was connected. HostGrpID The host group number where the host is deleted. WWN Indicates WWN of the host deleted from the host group. Num. of WWNs The number of hosts (WWN) deleted from the host group.
PAGE 153
Detailed information for this operation is shown in the following table. Table 130 Detailed information for Set Authentication operation Item Description Port The name of the port where the host deleted from host group was connected. HostGrpID The host group number where the host is deleted. The setting status of user authentication. Authentication Enable: user authentication enabled, Disable: user authentication disabled Num. of Authentication The number of user authentication set.
PAGE 154
Set CommandDev Set Command Device (CommandDev) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 132 Detailed information for Set CommandDev operation Item Description CU:LDEV The CU and LDEV numbers of the logical volume where the command device setting is changed. CommandDev Num.
PAGE 155
Item Description Num. of LDEVs The number of logical volumes where the command device setting is changed. Set FCSP Host operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Set FCSP Host,,Normal end,Seq.=xxxxx +{Port,HostGrpID,Kind,UserName,Change UserName}=[{1E,0x01,Add,1111111111111111,-}, {3E,0x01,Change,2222222222222222,3333333333333333},{5E,0x01,Delete,4444444444444444,-}], Num.
PAGE 156
Set FCSP Port Info Set Fibre-Channel Security Protocol (FCSP) Port Information operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 135 Detailed information for Set FCSP Port Info operation Item Description Port The name of the port where authentication parameter has been set.
PAGE 157
Item Switch DH Group Description The setting status whether to execute authentication by port. Disable: Do not authenticate, Enable: Authenticate Not used. (fixed to 0) The setting status of authentication method. Auth bi-directional: bi-directional authentication, unidirectional: unidirectional authentication UserName The user name of the port. Num. of Ports The number of ports where authentication parameter has been set.
PAGE 158
Set Fibre Address operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUNM],Set Fibre Address,,Normal end,Seq.=xxxxx +{Port,Fibre Addr.}=[{XX,1},{XX,126}],Num.of Ports=2 [LUNM] LUN Manager function Set Fibre Address Set Fibre Address operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 159
Value Address* Value Address* Value Address* Value Address* 12 D4 (11) 44 A3 (43) 76 63 (75) 108 2B(107) 13 D3 (12) 45 9F (44) 77 5C (76) 109 2A(108) 14 D2 (13) 46 9E (45) 78 5A (77) 110 29(109) 15 D1 (14) 47 9D (46) 79 59 (78) 111 27(110) 16 CE (15) 48 9B (47) 80 56 (79) 112 26(111) 17 CD (16) 49 98 (48) 81 55 (80) 113 25(112) 18 CC (17) 50 97 (49) 82 54 (81) 114 23(113) 19 CB (18) 51 90 (50) 83 53 (82) 115 1F(114) 20 CA (19) 52 8F
PAGE 160
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 140 Detailed information for Set Fibre Topology operation Item Description Port The name of the port where the topology of Fibre Channel is changed. Fabric Indicates whether the Fabric switch is enabled or disabled. Connection Num. of Ports The connecting mode of the Fabric switch selected.
PAGE 161
Item Description Option The host mode option set. Hexadecimal values are output. See Table 142 for the relation of output values and host mode option. Num. of Host Groups The number of host groups that the host mode setting is changed.
PAGE 162
Detailed information for this operation is shown in the following table. Table 143 Detailed information for Set IP Address operation Item Description Port The name of the port where the IP address has been set. IPVersion The Internet Protocol Version which is IPv4 (Internet Protocol Version 4). IPAddr The IP address set. SubNetMask The subnet mask set. GateWayAddr The gateway address set. DNSAddr The DNS server address set. Num. of Ports The number of ports where the IP address is set.
PAGE 163
Set Security Switch operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[LUNM],Set Security Switch,,Normal end, Seq.=xxxxx +{Port,Switch}=[{XX,Disable},{XX,Enable}],Num.of Ports=2 [LUNM] LUN Manager function Set Security Switch Set Security Switch operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 164
Detailed Information Detailed information for this operation is shown in the following table. Table 146 Detailed information for Set Speed Mode operation Item Description Channel Adapter (CHA) The Channel Adapter (CHA) name (name of channel adapter). Port Block The port block. Port block A, B, C, and D are output in case of a 16-port channel adapter. In case of an 8-port channel adapter, port block A and B are output. The mode set to the port.
PAGE 165
18 Logical Unit Number Expansion (LUSE) function Make LUSE operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[LUSE],Make LUSE,,Normal end,Seq.=xxxxx +LUSE(CU:LDEV)=[[0x00:0x00,0x00:0x01,0x00:0x02,0x00:0x03],[0x01:0x00,0x01:0x01,0x01:0x02, 0x01:0x03]],Num. of LUSEs=2 [LUSE] Logical Unit Number Expansion (LUSE) function Make LUSE Make Logical Unit Number Expansion (LUSE) operation Normal end The operation has ended normally. Seq.
PAGE 166
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 149 Detailed information for Release LUSE operation Item Description LUSE(CU:LDEV) The CU and LDEV numbers of the top LDEV. Num. of LUSEs The number of LUSE volumes cancelled.
PAGE 167
19 Maintenance function Blockade operation Example 1 (Blocking a cluster) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Blockade,,Normal end,Seq.=xxxxx +Location=Cluster-1 Example 2 (Blocking a PCB) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Blockade,,Normal end,Seq.=xxxxx +PCB=[CHA-1P],Num. of PCBs=1 +PDEV=HDD00-01 Example 3 (Blocking an LDEV) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Blockade,,Normal end,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num.
PAGE 168
Item Description PDEV The mounting location of the PDEV (physical device) to be blocked. PG The parity group number. Num. of PGs The number of parity groups. LDEV The LDEV number. Num. of LDEVs The number of LDEVs. Correction Copy operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Correction Copy,,Normal end, Seq.=xxxxx +PDEV=HDD00-01 [Maintenance] Maintenance function Correction Copy Correction Copy operation Normal end The operation has ended normally. Seq.
PAGE 169
Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 152 Detailed information for Drive Interrupt operation Item Description PDEV PDEV Format operation NOTE: This log information indicates the completion of Format operation and does not indicate the completion of Format processing. The Format processing requires some time.
PAGE 170
Format Stop operation NOTE: This log information is output when the format process is suspended. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Format Stop,,Normal end,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num. of PGs=1 –> in case of an external volume +PG=[V1-1],Num. of PGs=1 –> in case of a virtual volume +LDEV=[0x00-0x01],Num. of LDEVs=1 [Maintenance] Maintenance function Format Stop Format Stop operation Normal end The operation has ended normally. Seq.
PAGE 171
Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 155 Detailed information for Recover operation Item Location Description The cluster to be recovered. Cluster-1: Recover Cluster 1, Cluster-2: Recover Cluster 2 Replace operation Example 1 (Replacing parts) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance], Replace,,Normal end,Seq.
PAGE 172
Maintenance function Replace Replace operation Easy-Replace Easy-Replace is the parameter output when easy replacing a PDEV. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table.
PAGE 173
Restore operation Example 1 (Restoring a PCB) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Restore,,Normal end,Seq.=xxxxx +PCB=[CHA-1P],Num. of PCBs=1 +PDEV=HDD00-01 Example 2 (Restoring an LDEV) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Restore,,Normal end,Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +PG=[E1-1],Num. of PGs=1 –> in case of an external volume +PG=[V1-1],Num. of PGs=1 –> in case of a vertual volume +LDEV=[0x00-0x01],Num.
PAGE 174
[Maintenance] Maintenance function Restore Data Restore Data operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 158 Detailed information for Restore Data operation Item Description PDEV The mounting location of the PDEV.
PAGE 175
Item Description Battery The mounting location of the battery to be replaced. Not output when no batteries are installed or uninstalled. Define Indicates the installation or uninstallation of a battery. Not output when no batteries are installed or uninstalled. Install: Installation of a battery, Uninstall: Uninstallation of a battery Num. of Battery Pairs The number of batteries to be installed or uninstalled.
PAGE 176
Sequence number of log information (000000 to 999999) Transfer Config operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Transfer Config,,Normal end, Seq.=xxxxx [Maintenance] Maintenance function Transfer Config Transfer Config operation Normal end The operation has ended normally. Seq.
PAGE 177
Detailed information displays for this operation, as shown in the following table. Table 161 Detailed information for Type Change operation Item Description SFP The port which SFPs are inserted.. Type The type of the SFP or the PCB. Short Wave: Short wave, Long Wave: Long wave Num of SFPs The number of inserted SFPs. PCB The mounting location of the PCB to be replaced. Num. of PCBs The number of PCBs to be replaced.
PAGE 178
Verify Stop operation NOTE: Log information is output when the format process is suspended. user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[Maintenance],Verify Stop,,Normal end, Seq.=xxxxx +PG=[1-1],Num. of PGs=1 +LDEV=[0x00-0x01],Num. of LDEVs=2 [Maintenance] Maintenance function Verify Stop Verify Stop operation Normal end The operation has ended normally. Seq.
PAGE 179
20 Performance Control Base Monitor function Monitoring S/W operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[PCBM],Monitoring S/W,Enable 60sec,,Normal end, Seq.=xxxxx [PCBM] Performance Control Base Monitor function Monitoring S/W Monitoring Switch (S/W) operation Enable 60sec Enable 60 sec is selected as the parameter. The operation uses the following parameters, as shown in the following table.
PAGE 180
Performance Control Base Monitor function
PAGE 181
21 PORT function Change Port operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[PORT],Change Port,,Normal end,Seq.=xxxxx +Attribute=RCU Target ++Port=[1E,3E,5E,7E], Num.of Ports=4 [PORT] PORT function Change Port Change Port operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 182
PORT function
PAGE 183
22 Optional Product (PP) KEY function File operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[PP KEY],File,,Normal end,Seq.=xxxxx +File Name=C:\Dkc200\Home\Sample.plk ++{P.P. Name,Key Code}=[{JAVA API,XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX}, -{JAVA API,XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX}],Num. of PPs=2 [PP KEY] Optional License Key function File File operation Normal end The operation has ended normally. Seq.
PAGE 184
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 167 Detailed information for File Install operation Item Description P.P. Name The name of the program installed option. SLPR# The SLPR number of the SLPR where the option is installed. License Capa(GB) The licensed capacity of the installed option. The unit is GB (gigabyte). Num.
PAGE 185
[PP KEY] Option License Key function Uninstall Uninstall operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 169 Detailed information for Uninstall operation Item Description P.P. Name The name of the installed option.
PAGE 186
Optional Product (PP) KEY function
PAGE 187
23 Remote Control Unit (RCU) function Add Path operation Example 1 (CU Free is used) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[RCU],Add Path,,Normal end,Seq.=xxxxx +{S/N,Path Gr. ID,Controller ID}={99999,Default,4} ++{MCU Port,RCU Port}=[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H},{5H,7H}], Num. of Port Pairs=8 Example 2 (CU Free is not used) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[RCU],Add Path,,Normal end,Seq.
PAGE 188
Item Description Num. of Port Pairs The number of port pairs set. Add RCU operation Example 1 (CU Free is used) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[RCU],Add RCU,,Normal end,Seq.=xxxxx +{S/N,Path Gr. ID,Controller ID,Min. Path,MIH Time(s),Round Trip Time(ms),Incident,FREEZE}= {99999,Default,4,08,015,001,only to RCU host,Disable} ++{MCU Port,RCU Port}=[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H},{5H,7H}], Num.
PAGE 189
Item Description Min. Path The number of set minimum paths. MIH Time(s) The value of set RIO MIH (Remote I/O Missing Interrupt Handler) timer (wait time until data copy from MCU to RCU is completed). The unit is second. Round Trip Time(ms) The round-trip response time set (delay time for round-trip remote I/O). The unit is millisecond. This value is output when Continuous Access XP or TrueCopy for z/OS is used. Incident The set incident of the RCU.
PAGE 190
Detailed information for this operation is shown in the following table. Table 172 Detailed information for Change RCU Option operation Item Description S/N Indicates a serial number of the RCU device where the RCU option setting is changed. Path Gr. ID The RCU path group ID where the RCU optional setting is changed. When the path group ID is default setting, Default is output. Controller ID The controller ID of the RCU where the optional setting is changed.
PAGE 191
The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 173 Detailed information for Delete Path operation Item Description S/N The serial number of the device of RCU where the path has been deleted. Path Gr. ID The path group ID of the path deleted. When the path group is a default setting, Default is output.
PAGE 192
Detailed information for this operation is shown in the following table. Table 174 Detailed information for Delete RCU operation Item Description S/N The serial number of the device of RCU deleted. Path Gr. ID The path group ID of the RCU deleted. When the path group ID is a default setting, Default is output. Controller ID The controller ID of the RCU deleted. SSID The SSID of the RCU deleted.
PAGE 193
24 Serverless Backup Enabler (SBE) function Port-Group (Forced) operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SBE],Port-Group(Forced),,Normal end,Seq.=xxxxx +{Port Group#,Port Name,Host Group#,Time out(sec.),Result}=[{Free Port,1A,0,50,Normal End}, {1,1A,1,50,Normal End},{2,1A,2,50,Normal End}],Num. of Port Groups=XXX [SBE] Serverless Backup Enabler function Port-Group (Forced) Port-Group (Forced) operation Normal end The operation has ended normally. Seq.
PAGE 194
[SBE] Serverless Backup Enabler function Port-Group (Normal) Port-Group (Normal) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table. Table 176 Detailed information for Port-Group (Normal) operation Item Description Port Group# The port group number specified (1 to 128). For free ports, Free Port is output.
PAGE 195
25 Volume Shredder (SHRED) function End Shredding operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SHRED],End Shredding,,Normal end,Seq.=xxxxx +{Times,Result}=[{1,Nomal},{2,Nomal},{3,Error}],Num. of Data=3 [SHRED] SHRED function End Shredding End Shredding operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Detailed Information Detailed information displays for this operation, as shown in the following table.
PAGE 196
SHRED function Set Shredding Set Shredding operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 178 Detailed information for Set Shredding operation Item Description The owner ID. OwnerID 0: Indicates XP Remote Web Console 0xXX: Owner ID is expressed in two digits of the hexadecimal format The data type.
PAGE 197
Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 179 Detailed information for Suspend Shredding operation Item Description The owner ID.
PAGE 198
Volume Shredder (SHRED) function
PAGE 199
26 Business Copy XP function Change Reserve operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[BC],Change Reserve,,Normal end,Seq.=xxxxx +Attribute=Set ++{VOL(CU:LDEV),Result}=[{0xXX:0xYY,Normal end},{0xXX:0xYY, Error(xxxx-yyyy)}],Num. of Vols=2 [BC] Business Copy function Change Reserve Change Reserve operation Normal end The operation has ended normally. Seq.
PAGE 200
Initialize Initialize operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Option operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[BC],Option,,Normal end,Seq.=xxxxx +Swap & Freeze=Enable,HOST I/O Performance=Enable,Reserve03=Enable,(snip),Reserve32=Disable [BC] Business Copy function Option Option operation Normal end The operation has ended normally. Seq.
PAGE 201
Paircreate operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 182 Detailed information for Pair Create operation Item Description Copy Pace The set copy speed. Faster: High speed, Medium: Medium speed, Slower: Low speed P-VOL(CU:LDEV) The CU number and the LDEV number of the primary volume in the created pair.
PAGE 202
Detailed information for this operation is shown in the following table. Table 183 Detailed information for Pairresync operation Item Description Copy Pace The set copy speed.Faster: High speed, Medium: Medium speed, Slower: Low speed The type of resynchronization.
PAGE 203
Detailed information for this operation is shown in the following table. Table 184 Detailed information for Pairsplit operation Item Description The set copy speed. Copy Pace Faster: High speed Medium: medium speed Slower: Low speed The split type. Split Type Quick Split: Pair split by background copy Steady Split: Pair split by update copy P-VOL(CU:LDEV) The CU number and the LDEV number of the primary volume in the split pair.
PAGE 204
Item Description S-VOL(CU:LDEV) The CU number and the LDEV number of the primary volume in the suspended pair. The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Result xxxx: Part code, yyyyy: Error code Num. of Pairs The number of suspended pairs. Pairsplit-S operation Example 1 (When Business Copy is used) user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[BC],Pairsplit-S,,Normal end,Seq.
PAGE 205
Item Description S-VOL(CU:LDEV) The CU number and the LDEV number of the primary volume in the deleted pair. MU The Snapshot ID of the deleted pair, enabled when Kind=1 and Option=Pair. The result of operation. Result Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of deleted pairs.
PAGE 206
Business Copy XP function
PAGE 207
27 ShadowImage (SI) z/OS function Add Pair operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SI z/OS(R)],Add Pair,,Normal end,Seq.=xxxxx +Copy Pace=Faster ++{S-VOL(CU:LDEV),T-VOL(CU:LDEV),Result}=[{0xAA:0xBB,0xCC:0xDD,0,Normal end}, {0xAA:0xBB,0xCC:0xDD,1,Error(xxxx-yyyy)}],Num. of Pairs=2 [SI z/OS] ShadowImage z/OS function (for the IBM z/OS) Add Pair Add Pair operation Normal end The operation has ended normally. Seq.
PAGE 208
Change Reserve operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[SI z/OS(R)],Change Reserve,,Normal end, Seq.=xxxxx +Attribute=Set ++{VOL(CU:LDEV),Result}=[{0xXX:0xYY,Normal end},{0xXX:0xYY, Error(xxxx-yyyy)}], Num.of Vols=2 [SI z/OS] ShadowImage z/OS function (for the IBM z/OS) Change Reserve Change Reserve operation Normal end The operation has ended normally. Seq.
PAGE 209
Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 189 Detailed information for CTG operation Item Description CTG The consistency group number. Command Indicates whether the CT group (consistency group) is newly registered or the existing CT group is deleted. Add: Registration of CT group, Delete: deletion of CT group The result of operation.
PAGE 210
Item Description The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Result xxxx: Part code, yyyyy: Error code Num. of Pairs The number of deleted pairs. Exp R_TBL(Disable) operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[SI z/OS(R)],Exp R_TBL(Disable),,Normal end, Seq.=xxxxx [SI z/OS] ShadowImage z/OS function (for the IBM z/OS) Exp R_TBL(Disable) Disable Relationship Expansion operation Normal end The operation has ended normally. Seq.
PAGE 211
Initialize Initialize operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of log information (000000 to 999999) Option operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SI z/OS(R)],Option,,Normal end,Seq.
PAGE 212
Resync Pair operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SI z/OS(R)],Resync Pair,,Normal end,Seq.=xxxxx +Copy pace=Faster,Resync Type=Normal Copy ++{S-VOL(CU:LDEV),T-VOL(CU:LDEV),Result}=[{0xAA:0xBB,0xCC:0xDD,Normal end}, {0xAA:0xBB,0xCC:0xDD,Error(xxxx-yyyy)}],Num. of Pairs=2 [SI z/OS] ShadowImage z/OS function (for the IBM z/OS) Resync Pair Resync Pair operation Normal end The operation has ended normally. Seq.
PAGE 213
ShadowImage z/OS function (for the IBM z/OS) Set SCP Time Set State Change Pending (SCP) Time operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 193 Detailed information for Set SCP Time operation Item Description CU The CU number. SCP Delay Time(s) The State Change Pending (SCP) delay time in seconds. Num.
PAGE 214
Item Description The split type. Split Type Quick Split: Pair split by background copy, Steady Split: Pair split by update copy S-VOL(CU:LDEV) The CU number and the LDEV number of the source volume in the split pair. T-VOL(CU:LDEV) The CU number and the LDEV number of the target volume in the split pair. The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Result xxxx: Part code, yyyyy: Error code Num. of Pairs The number of split pairs.
PAGE 215
28 SNMP function Set SNMP Agent operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[SNMP],Set SNMP Agent,,Normal end,Seq.=xxxxx +Install=Disable +Manager=[(158.214.133.001),(158.214.133.002),(158.214.133.003),(158.214.133.004), (158.214.133.005),(158.214.133.006),(158.214.133.007),(158.214.133.008),(158.214.133.009), -(158.214.133.010),(158.214.133.011),(158.214.133.012),(158.214.133.013),(158.214.133.014), (158.214.133.015),(158.214.133.016),(158.214.133.017),(158.214.133.018),(158.214.133.
PAGE 216
Item Description Num. of Managers The number of the registered SNMP managers. Community The registered community name. Trap The IP address where the trap of community is reported. Num. of Traps The number of traps reported. Num. of Communities The number of registered communities. System Group The setting of system group information (Name, Contact, and Location). Name The nickname of the device set. Contact The setting name of the system administrator.
PAGE 217
29 Performance Control function Change PPCGrp operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[PFC],Change PPCGrp,,Normal end,Seq.=xxxxx +{PPC Group,Priority,UpperLimit,Mode}=[{XXXXXXXXXXXXXXXX,Non-Prio,XXXXXXXX,IOPS}], Num. of PPC Groups=1 [PFC] Performance Control function Change PPCGrp Change Prioritized Port Control Group (PPCGrp) operation Normal end The operation has ended normally. Seq.
PAGE 218
Performance Control function Clear PPC Info Clear Prioritized Port Control (PPC) Information operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Default Set operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx,00:00,[PFC],Default Set,Kind=WWN,,Normal end,Seq.=xxxxx [PFC] Performance Control function Default Set Default Set operation Kind=WWN WWN is selected as the default.
PAGE 219
Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 199 Detailed information for PPCGrp Del/Chg operation Item Description The operation executed. Mode Delete: Deletion of SPM group, Update: Change of the SPM group name PPC Group The SPM group name to be operated. Change Name The SPM group name after change. This value is output only when the SPM group name is changed. Num.
PAGE 220
Set All Prio WWN operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[PFC],Set All Prio WWN,,Normal end,Seq.=xxxxx +{AllPriority,Threshold,Mode}={Enable,XXXXXXXX,IOPS} [PFC] Performance Control function Set All Prio WWN Set All Priority (Prio) World Wide Name (WWN) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 221
WWN is selected as the parameter. The operation uses the following parameters, as shown in the following table. Table 202 Parameters for Set Ctrl Kind operation Parameter Description Port Port Control is applied without the All Thresholds value being set. All Port Port Control is applied with the All Thresholds value being set. WWN WWN Control is applied. This value is output whether the All Thresholds value is set or not. Normal end The operation has ended normally. Seq.
PAGE 222
Item Description Threshold/Upper Limit The threshold in case of prioritized port and the upper limit value in case of nonprioritized port. This value is output only when the threshold or the upper limit value is set. The type of rate used for upper limit control and threshold control. IOPS: I/O rate, KB/s: Transfer rate Mode This value is output when the threshold or the upper limit value is set. Num. of Ports The number of ports that the setting is changed.
PAGE 223
Update Port WWN operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[PFC],Update Port WWN,,Normal end,Seq.=xxxxx +{Mode,WWN, Name,Priority}=[{Add ,0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX,Non-Prio}, ++Port=[1A,3A],Num. of Ports=2],Num of WWNs=1 [PFC] Performance Control function Update Port WWN Update Port World Wide Name (WWN) operation Normal end The operation has ended normally. Seq.
PAGE 224
Performance Control function Update PPCGrp Update Prioritized Port Control Group (PPCGrp) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 206 Detailed information for Update PPCGrp operation Item Description The operation executed.
PAGE 225
Update WWN Update World Wide Name (WWN) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 207 Detailed information for Update WWN operation Item Description The operation executed. Update Mode Change WWN: Change of host bus adapter Change Nickname: Change of SPM name of the host bus adapter WWN Indicates WWN of the host bus adapter.
PAGE 226
Performance Control function
PAGE 227
30 Continuous Access XP function Add CTG operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXP],Add CTG,,Normal end,Seq.=xxxxx +{CTG,Path,Offloading(s),Inflow Control,Copy Pending(min.),RCU Ready(min.)}= {0x00,Fibre,090,Enable,05,05} [CAXP] Continuous Access XP function Add CTG Add Consistency Group (CTG) operation Normal end The operation has ended normally. Seq.
PAGE 228
Change Async Option operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXP],Change Async Option,,Normal end,Seq.=xxxxx +{CLPR,Rate(%),Delay Start(%),Delay Increase(%)}={00,050,030,040} [CAXP] Continuous Access XP function Change Async Option Change Async Option operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 229
Detailed information for this operation is shown in the following table. Table 210 Detailed information for Change CTG Option operation Item Description CTG The consistency group number of the consistency group (CT group) where the option is changed. Offloading(s) The value set to the monitoring time of transfer to the side file. The unit is second. Inflow Control Indicates whether the inflow control to the cache is enabled or disabled.
PAGE 230
Item Description Indicates whether to report the remote copy-related SIM. Service SIM Report, Not Report Indicates whether the host supports PPRC. PPRC Support Yes: support, No: not support SCP Delay Time(s) The SCP delay time when the pair is suspended. The unit is second. Num. of CUs The number of CUs set. Change Pair Option operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXP],Change Pair Option,,Normal end,Seq.
PAGE 231
Item Description The result of operation. Result Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of changed pairs. Delete CTG operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[CAXP],Delete CTG,0x00,,Normal end,Seq.=xxxxxx [CAXP] Continuous Access XP function Delete CTG Delete Consistency Group (CTG) operation 0x00 This operation uses the following parameters, as shown in the following table.
PAGE 232
Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 214 Detailed information for Paircreate operation Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the volume specified to the primary volume when the pair is created sequentially.
PAGE 233
Pairresync operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXP],Pairresync,,Normal end,Seq.=xxxxxx +{P-VOL(Port-G-ID-LUN), S-VOL(Port-G-ID-LUN),Fence Level,Copy Pace,Priority,Range, Error Level,Result}= -{1A-0x00-0x000, 1B-0x00-0x000,Never,15,256,Group,Group,Normal End}, {1A-0x00-0x001,Never,15,256,Group,Group,Normal End},(snip) -(snip), Num. of Pairs=xx [CAXP] Continuous Access XP function Pairresync Pairresync operation Normal end The operation has ended normally. Seq.
PAGE 234
Item Description Num. of Pairs The number of restored pairs. Pairsplit-r operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXP],Pairsplit-r,,Normal end,Seq.=xxxxxx +{P-VOL(Port-G-ID-LUN), S-VOL(Port-G-ID-LUN),Type, S-VOL Write,Kind,Range,Mode, Result}= -{1A-0x00-0x000, 1B-0x00-0x000,P-VOL,Disable,S-VOL,Group,Drain,Normal End}, {1A-0x00-0x001,Disable,S-VOL,Group,Drain,Normal End},(snip) -(snip), Num.
PAGE 235
Item Description The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Result xxxx: Part code, yyyyy: Error code Num. of Pairs The number of split pairs. Pairsplit-S operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXP],Pairsplit-S,,Normal end,Seq.
PAGE 236
Item Description The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Result xxxx: Part code, yyyyy: Error code Num. of Pairs The number of deleted pairs. Start Pair operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[CAXP], Start Pair,,Normal end,Seq.
PAGE 237
31 TrueCopy (TC) z/OS function Add CTG operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[TC z/OS(R)],Add CTG,,Normal end,Seq.=xxxxxx +{CTG,Path,Offloading(min.),Inflow Control,Copy Pending(min.),RCU Ready(min.),Timer Type}= {0x00,Fibre,005,Enable,05,05,System} [TC z/OS] TrueCopy z/OS function (for IBM z/OS) Add CTG Add Consistency Group (CTG) operation Normal end The operation has ended normally. Seq.
PAGE 238
Add Pair operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00, [TC z/OS(R)],Add Pair,,Normal end,Seq.=xxxxxx +{M-VOL(CU:LDEV),R-VOL(LDEV),S/N,SSID,ControllerID,Type, Initial Copy, Fence Level, Copy Pace, Priority,Diff,CFW,DFW,TS,CTG, Error Level,Result}= -{0x00:0x00,0xFF,99999,0x0004,4,Async,Entire,Never,15,032,Auto,Only M-VOL,-,–,0x00,Group, Normal End}, (snip) -(snip), Num.of Pairs=xx [TC z/OS] TrueCopy z/OS function (for IBM z/OS) Add Pair Add Pair operation Normal end The operation has ended normally.
PAGE 239
Item Description DFW Indicates whether DFW use to the remote volume is set or not. This value is output when the synchronous pair is created only. When the asynchronous pair is created, a hyphen (-) is output. Not required: DFW not required, Required: DFW required TS Indicates whether to transfer timestamp of the host to the remote volume when the pair is created. This value is output when the asynchronous pair is created only. When the asynchronous pair is created, a hyphen (-) is output.
PAGE 240
Item Description The PPRC TSO command. PPRC Command 16CT Compatible: Format compatible to 16 CT group is used, Native: Native Change CTG Option operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[TC z/OS(R)], Change CTG Option,,Normal end, Seq.=xxxxx +{CTG, Offloading(min.),Inflow Control,Copy Pending(min.),RCU Ready(min.
PAGE 241
Change Option operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[TC z/OS(R)],Change Option,,Normal end, Seq.=xxxxxx +{ Max Initial Copy,Path Blockade Watch(s),Path Blockade SIM Watch(s) }={128,45,70} +{CU,Service SIM,PPRC Support,SCP Delay Time(s)}= -{0x00,Not Report,Yes,600},{0x01,Not Report,Yes,600},{0x02,Not Report,Yes,600}, {0x03,Not Report,Yes,600},{0x04,Not Report,Yes,600},(snip) -(snip), Num.
PAGE 242
[TC z/OS] TrueCopy z/OS function (for IBM z/OS) Change Pair Option Change Pair Option operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 223 Detailed information for Change Pair Option operation Item Description M-VOL(CU:LDEV) The CU number and the LDEV number of the main volume where the pair option is changed.
PAGE 243
The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Delete Command Device operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[TC z/OS(R)], Delete Cmd.Dev,,Normal end, Seq.=xxxxxx +{VOL(CU:LDEV),Result}= -{0x3C:0xEF,Normal end}, (snip) -(snip),Num of Volumes=xx Abstract [TC z/OS] TrueCopy z/OS function (for IBM z/OS) Delete Cmd.Dev Delete Command Device operation Normal end The operation has ended normally. Seq.
PAGE 244
0x00 The operation uses the following parameters, as shown in the following table. Table 225 Parameters for Delete CTG operation Item Description 0x00 to 0x7F The number of the deleted consistency group. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Delete Pair operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[TC z/OS(R)],Delete Pair,,Normal end,Seq.
PAGE 245
Item Description The delete range set. This value is output when the asynchronous pair is deleted only. Volume: Volume (appropriate TrueCopy for z/OS(R) Asynchronous pairs only) Range Group: Group (all suspended TrueCopy for z/OS(R) Asynchronous pairs in the consistency group) The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Result xxxx: Part code, yyyyy: Error code Num. of Pairs The number of deleted pairs.
PAGE 246
Item Description TS Indicates whether to transfer timestamp of the host to the remote volume when the pair is created. This value is output when the asynchronous pair is created only. When the asynchronous pair is created, a hyphen (-) is output. Enable: Transfer, Disable: Do not transfer. The resume range set (the range to restore the asynchronous pair). This value is output when the asynchronous pair is restored only.
PAGE 247
Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 229 Detailed information for Script operation Item Description FileName The file name of the executed script. Start Pair operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[TC z/OS(R)], Start Pair,,Normal end,Seq.=xxxxxx [TC z/OS] TrueCopy z/OS function (for IBM z/OS) Start Pair Start Pair operation.
PAGE 248
Detailed Information Detailed information for this operation is shown in the following table. Table 230 Detailed information for Suspend Pair operation Item Description VOL(CU:LDEV) The CU and LDEV numbers of the connected volume in the split (suspended) pair. PairVOL(LDEV) The LDEV number of the paired volume in the split (suspended) pair. Type The volume type of the connected volume. M-VOL: Main volume, R-VOL: Remote volume SSB The SSB[F/M=FB] option setting.
PAGE 249
32 Continuous Access XP Journal function Journal-Option operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXJ],Journal-Option,,Normal end,Seq.=xxxxx +{JNLG,MetaData Ratio,Extent,Data Overflow Watch(s),Inflow Control,Copy Pace, Path Watch Time,Forward Path Watch Time,Use of Cache,Speed of Line(Mbps), Delta resync Failure,Result}= -{0x01,32,32,20,No,150,30(min.),Yes,Not Use,256,Entire,Normal end},(snip), {0x02,32,32,20,No,150,12(hour),No,Use,256,Entire,Normal end},Num.
PAGE 250
Item Description Forward Path Watch Time Indicates whether to transfer the path blockade watch period set to the master journal group to the restore journal group. Yes: transfer, No: do not transfer. Whether to store the journal data in the restore journal group in cache. Use of Cache Use: Store the journal data in cache. Not used: Store the journal data in journal volume Speed of Line(Mbps) The transfer speed of the communication line. The unit is megabits per second (Mbps).
PAGE 251
Detailed information Detailed information for this operation is shown in the following table. Table 233 Detailed information for Journal-Vol operation Item Description JNLG The journal group number. CU:LDEV The CU and LDEV numbers. The result of operation. Result Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of JNL Grps The number of journal groups.
PAGE 252
Paircreate operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00, [CAXJ],Paircreate,,Normal end,Seq.=xxxxxx +{P-VOL(Port-G-ID-LUN),S-VOL(Port-G-ID-LUN),MirrorID,S/N,CTRLID,Priority,CTG,Initial Copy, M-JNLG,R-JNLG,Path Gr.ID,Error Level,Result}=[{1A-0x00-0x000,5A-0x00-0x000,0x00,65432,4,32, 0x05,Entire,0x02,0x00,Default,Group,Normal end} (snip) -{1A-0x00-0x001,5A-0x00-0x001,0x00,65432,4,32,0x05,Entire,0x02,0x00,Default,Group, Normal end}], Num.
PAGE 253
Item Description Num. of Pairs The number of pairs. Pairresync operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXJ],Pairresync,,Normal end,Seq.=xxxxx +{P-VOL(Port-G-ID-LUN),S-VOL(Port-G-ID-LUN),MirrorID,S/N,CTRLID,Priority,CTG,Range,M-JNLG, R-JNLG,Error Level,Resync Mode,Result}=[{1A-0x00-0x000,5A-0x00-0x000,0x00,65432,4,32,0x05, Group,Normal end}, (snip) -{1A-0x00-0x001,5A-0x00-0x001,0x00,65432,4,32,0x05,Group,0x02,0x00,Group,Normal, Normal end}],Num.
PAGE 254
Item Description Resync Mode Indicates the Resync Mode. Normal: normal resync, Delta: delta resync Return to standby: return to standby status The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Result xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs. Pairsplit-r operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00, [CAXJ],Pairsplit-r,,Normal end,Seq.
PAGE 255
Item Range Suspend Mode Description The split range. LU: LU range, Group: Group range The suspend mode. Purge: Purge mode, Flush: Flush mode The result of operation. Result Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs. Pairsplit-S operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00, [CAXJ],Pairsplit-S,,Normal end,Seq.
PAGE 256
Item Description The split range. Range LU: LU range, Group: Group range Delete Mode The delete mode. Normal: Normal mode, Force: Force mode The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Result xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs. Pair-Option operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXJ],Pair-Option,,Normal end,Seq.
PAGE 257
Item Description The result of operation. Result Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs. System-Option operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[CAXJ],System-Option,,Normal end,Seq.=xxxxx +Max Initial Copy=64 [CAXJ] Universal Replicator function System-Option System-Option operation Normal end The operation has ended normally. Seq.
PAGE 258
Continuous Access XP Journal function
PAGE 259
33 Universal Replicator (UR) z/OS function Add Pair operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[UR z/OS(R)],Add-Pair,,Normal end,Seq.=xxxxxx +{P-VOL(CU:LDEV),S-VOL(CU:LDEV),MirrorID,S/N,CTRLID,Priority,Initial Copy,M-JNLG,R-JNLG, Path Gr.ID,Error Level,CFW,Result}=[{0x00:0x00,0x20:0x00,0x00,65432,4,32,Entire,0x02,0x00, Default,Group,Copy to S-VOL,Normal end}(snip) -{0x00:0x01,0x20:0x01,0x00,65432,4,32,Entire,0x02,0x00,Default,Group,Copy to S-VOL, Normal end}],Num.
PAGE 260
Item Description Error Level The error level. LU: volume level, Group: group level Indicates whether the cache-fast-write data is copied to the primary data volume is enabled or not. CFW Only P-VOL: Not copied, Copy to S-VOL: Copied The result of operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Result xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs. Clear-SIM operation name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[UR z/OS(R)],Clear-SIM,,Normal end,Seq.
PAGE 261
Detailed information Detailed information for this operation is shown in the following table. Table 242 Detailed information for Delete-Pair operation Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary data volume. S-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary data volume. MirrorID The mirror ID. S/N The serial number of the device (storage system). CTRLID The controller ID.
PAGE 262
Add is selected as the parameter. This operation uses the following parameters: Table 243 Parameters for Edit-EXCTG operation Item Description Add Add journal groups to the extended consistency group. Remove Remove journal groups from the extended consistency group. Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 263
Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 245 Detailed information for Journal-Option operation Item Description JNLG The journal group number. MetaData Ratio The ratio of the metadata to the journal data. When the ratio is 1:32, the number for MetaData Ratio is 32. Extent The number of extents.
PAGE 264
Journal-Vol operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[UR z/OS(R)],Journal-Vol,Add,,Normal end, Seq.=xxxxxx +JNLG=0x00 ++{CU:LDEV,Result}=[{0x00:0x01,Normal end},{0x00:0x02,Normal end}],{0x00:0x03,Normal end}] +JNLG=0x01 ++{CU:LDEV,Result}=[{0x01:0x01,Normal end},{0x01:0x02,Normal end},{0x01:0x03,Normal end}, {0x01:0x04,Normal end},{0x01:0x05,Normal end},{0x01:0x06,Normal end}, {0x01:0x07,Normal end}, (snip) -{0x01,0x0,Normal end}] +Num.
PAGE 265
Journal-Vol operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[UR z/OS(R)],Journal-Vol,Group-Delete,, Normal end,Seq.=xxxxx +{JNLG,Result}={0x80,Normal end},{0x81,Normal end},Num. of JNL Grps=2 [UR z/OS] Universal Replicator z/OS function (for IBM z/OS) Journal-Vol Journal-Vol operation Group-Delete Group-Delete is selected as the parameter. The journal group is deleted. Normal end The operation has ended normally. Seq.
PAGE 266
Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 249 Detailed information for Pair-Option operation Parameter Description P-VOL(CU:LDEV) The CU and LDEV numbers of the primary data volume. S-VOL(CU:LDEV) The CU and LDEV numbers of the secondary data volume. MirrorID The mirror ID. M-JNLG The master journal group number. R-JNLG The restore journal group number.
PAGE 267
Detailed information for this operation is shown in the following table. Table 250 Detailed information for Resume-Pair operation Parameter Description P-VOL(CU:LDEV) The CU and LDEV numbers of the primary data volume. S-VOL(CU:LDEV) The CU and LDEV numbers of the secondary data volume. MirrorID The mirror ID. S/N The serial number of the device (storage system). CTRLID The controller ID. Priority The priority of copy. Range The range to restore the pair.
PAGE 268
Detailed Information Detailed information for this operation is shown in the following table. Table 251 Detailed information for Suspend-Pair operation Parameter Description P-VOL(CU:LDEV) The CU and LDEV numbers of the primary data volume. S-VOL(CU:LDEV) The CU and LDEV numbers of the secondary data volume. MirrorID The mirror ID. S/N The serial number of the device (storage system). CTRLID The controller ID. Indicates whether the split data volume is a primary or primary data volume.
PAGE 269
Detailed Information Detailed information for this operation is shown in the following table. Table 252 Detailed information for System-Option operation Item Description Max Initial Copy The number of volumes you can copy at a time during an initial copy operation. CU The CU numbers. Change SIM Report Whether to report SIM to the host or not. Report. Not report. Num of CUs The number of CUs (fixed to 64).
PAGE 270
Universal Replicator (UR) z/OS function
PAGE 271
34 External Storage XP function Add-Lu2 operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[EXS],Add-Lu2,,Normal end,Seq.=xxxxxx +{Vendor,Product,Serial,Dev,Dev-Name,D-Type,Capa(blocks),Group,IOSup,CM,CLPR,Type, UsedCapa(blocks),Result}= {{HITACHI,9970V,28528,0001,DF600,0x0000,4294967296,E1-1,Enable,Disable,0,OPEN-V, 4294967296, Normal end}, ++{CU:LDEV,Capa(MB),SSID}={0x03:0x00,3287040,0x20},Num.
PAGE 272
Item Description CM Indicates whether the cache mode is enabled or disabled; Enable: Mode is enabled, Disable: Mode is disabled. CLPR The CLPR number of the CLPR set to be used to access the mapped external volume. Type The emulation type of the mapped external volume. UsedCapa(blocks) The capacity of the volume used by Data Retention Utility. The result of operation.
PAGE 273
Detailed information for this operation is shown in the following table. Table 254 Detailed information for Add-Wwn operation Item Description WWN The newly registered WWN of the port in the external storage system. The result of operation. Result Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of WWNs The number of registered WWNs. Alternate-Path operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[EXS],Alternate-Path,,Normal end,Seq.
PAGE 274
Item Description LUN The LUN of the external volume that the alternate path is set. Num. of Groups The number of external volume groups set. NOTE: The status does not change immediately after you perform the Alternate-Path operation. As a result, errors may occur after you perform the operation. Check-Paths operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[EXS],Check-Paths,,Normal end,Seq.
PAGE 275
NOTE: The status does not change immediately after you perform the Check-Paths operation. As a result, errors may occur after you perform the operation. ChkPath-RestoreVol operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[EXS],ChkPath-RestoreVol,,Normal end, Seq.=xxxxxx +{Group,Result}=[{E1-1,Normal End},{E1-2,Error(605-3003)},{E1-3,Normal End}, {E1-4,Normal End}],Num.
PAGE 276
[EXS] External Storage function Delete-Lu (Force) Delete Logical Unit (LU) (Force) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed Information isplays for this operation, as shown in the following table. Table 258 Detailed information for Delete-Lu (Force) operation Item Description Group The group number of the external volume that the path is restored. The result of operation.
PAGE 277
Item Description The result of operation. Result Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Groups The number of external volumes resumed. Disconnect-Paths operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[EXS],Disconnect-Paths,,Normal end,Seq.=xxxxxx +{Group,Port,WWN,LUN,Result}=[{E1-1,1A,50060E8000C3E214,0x1111,Normal end}, {E1-2,1A,50060E8000C3E214,0x1111,Error(605-8122)}, -{E1-4,1A, 50060E8000C3E214,0x1111,Normal end}],Num.
PAGE 278
Disconnect-Volume operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[EXS],Disconnect-Volume,,Normal end,Seq.=xxxxxx +{Group,Result}=[{E1-1,Normal End},{E1-2,Error(605-3003)},{E1-3,Normal End}, {E1-4,Normal End}],Num of Groups=XXX [EXS] External Storage function Disconnect-Volume Disconnect-Volume operation Normal end The operation has ended normally. Seq.
PAGE 279
The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 262 Detailed information for WwnTimer operation Item Description WWN The WWN of the external storage system. I/O-TOV The I/O time over value set. Quedepth The Quedepth value (the number of commands issuable). LinkDown The Path Blockade watch value. The result of operation.
PAGE 280
External Storage XP function
PAGE 281
35 Virtual LVI / Virtual LUN (VLL) function Install CV operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VLL],Install CV,,Normal end,Seq.=xxxxxx +{PG,CU:LDEV,SLOT,Emulation,Size,Unit}=[{XX-XX-(X),0xXX-0xXX,0xXXXX,OPEN-V,XXXXXXXX,KB}, {X-X-(X),0xXX-0xXX,0xXXXX,OPEN-V,XXXXXXXX,KB}],Num. of LDEVs=2 [VLL] Virtual LVI / Virtual LUN function Install CV Install Customized Volume (CV) operation No parameter or Non Format No parameter is selected.
PAGE 282
Item Description The slot number. NOTE: SLOT A hyphen (-) is output when not specified. Emulation The emulation type. Size The user-specified capacity. The unit of the CV capacity. NOTE: The output unit is different according to the setting. Unit KB: For open-system volume Cyl: For mainframe volume LBA: For external volume Num. of LDEVs The number of LDEVs. Make Volume operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VLL],Make Volume,,Normal end,Seq.
PAGE 283
Detailed information for this operation is shown in the following table. Table 266 Detailed information for Make Volume operation Item Description The parity group number. NOTE: PG The parity group number whose first letter is E indicates that an external volume is present in the parity group. CU:LDEV The CU and LDEV numbers. Emulation The emulation type. Size The user-specified capacity. The unit of the CV capacity. NOTE: Unit The output unit is different according to the setting.
PAGE 284
Detailed information for this operation is shown in the following table. Table 267 Detailed information for Set SSID operation Item Description The SSID number. NOTE: SSID The SSID specified when Volume Initialize or Make Volume is executed is also output. Start CU:LDEV The starting CU number and LDEV numbers. Num. of SSIDs The number of SSID Volume Initialize operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[VLL],Volume Initialize,,Normal end,Seq.
PAGE 285
Detailed information for this operation is shown in the following table. Table 269 Detailed information for Volume Initialize operation Item Description The parity group numbers. NOTE: PG The parity group number whose first letter is E indicates that an external volume is present in the parity group. The CU and LDEV numbers. CU:LDEV NOTE: None is output when the CU and LDEV numbers are not specified. Num. of PGs The number of parity groups.
PAGE 286
Virtual LVI / Virtual LUN (VLL) function
PAGE 287
36 Auto LUN (ALUN) function Create Auto Plan operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[ALUN],Create Auto Plan,,Normal end,Seq.=xxxxxx [ALUN] Auto LUN function Create Auto Plan Create Auto Plan operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Del Auto Plan Log operation user-name,xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,[ALUN],Del Auto Plan Log,,Normal end,Seq.
PAGE 288
Delete Auto Plan operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 271 Detailed information for Delete Auto Plan operation Item Description The operation executed. PlanNo • Number: The number is output when one auto migration plan is deleted.
PAGE 289
The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 272 Detailed information for Set Auto Plan Param operation Item Description The operation executed. SetType PlanSwitch • Default: A default auto migration plan is applied. (Click Set after clicking Default.) • Customize: A customized auto migration plan is applied.
PAGE 290
[ALUN] Auto LUN function Set Class Threshold Set Class Threshold operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 273 Detailed information for Set Class Threshold operation Item Description ClassName The name of HDD class which the threshold is changed. The class name is indicated by the alphabet from A to J.
PAGE 291
Detailed information for this operation is shown in the following table. Table 274 Detailed information for Set Fixed PG operation Item Description The operation executed to the parity group. Type Set: Fixed parity group setting Release: Normal parity group setting PG The ID of the parity group whose setting has been changed. Num. of PGs The number of parity groups whose setting has been changed.
PAGE 292
Item Description Num. of LDEVs The number of manual migration plans set and deleted. Set Plan Condition operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VM],Set Plan Condition,,Normal end,Seq.=xxxxxx +{SetType,StartTime,TimeRequiredMax(min.),AvailablityMax(%),VolumeMax}= [{Default,24:00,120,100,65535}] Num. of Data = 1 [ALUN] Auto LUN function Set Plan Condition Set Plan Condition operation Normal end The operation has ended normally. Seq.
PAGE 293
Set Reserved Vol operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VM],Set Reserved Vol,,Normal end,Seq.=xxxxxx +{Set,CU:LDEV,Result}=[{Reserved,0x00:0x00,Normal end},{ Reserved,0x00:0x01,Normal end}, { Reserved,0x00:0x02,Normal end},{ Reserved,0x00:0x03,Normal end}, { Reserved,0x00:0x04,Normal end},{ Reserved,0x00:0x05,Normal end}, { Reserved,0x00:0x06,Normal end}] Num. of LDEVs = 7 [ALUN] Auto LUN function Set Reserved Vol Set Reserved Vol operation Normal end The operation has ended normally. Seq.
PAGE 294
Auto LUN (ALUN) function
PAGE 295
37 HP Disk/Cache Partition function Set operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[D/C PR],Set,,Normal end,Seq.=xxxxxx +Delete SLPR=[xx,xx],Num. of SLPRs=xx +Delete CLPR=[xx,xx],Num. of CLPRs=xx +SLPR=xx:xxxxxxxxxxxxxx,Operation=xxxxx ++Port=[CLx-x,CLx-x],Num. of Ports=xx ++CU=[0xXX,0xXX] ,Num. of CUs=xx ++SSID=[0xXXXX,0xXXXX],Num. of SSIDs=xx ++CLPR=xx:xxxxxxxxxxxxxx,Cache(MB)=xxxxx,Cache Residency(MB)=xxxx, Num.
PAGE 296
Item Description CU The CU number belonging to SLPR. Num. of CUs The number of CUs belonging to SLPR. SSID Indicates SSID belonging to SLPR. A space is output in case of SLPR0. Num. of SSIDs The number of SSIDs belonging to SLPR.0 (zero) is output in case of SLPR0. CLPR The CLPR number and the CLPR name belonging to SLPR. Cache(MB) The cache capacity set. The unit is megabyte (MB). Cache Residency(MB) The Cache Residency capacity set. The unit is megabyte (MB). Num.
PAGE 297
38 Volume Retention Manager (VRM) function Attribute operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VRM],Attribute,,Normal end,Seq.=xxxxxx +{CU:LDEV,Attribute,Result}=[{0x00:0x01,0x80,Normal end},{0x00:0x02,0x82,Error(9205-8122), {0x00:0x03,0x81,Normal end},{0x00:0x03,0x81,Normal end}],Num. of LDEVs=XXX [VRM] Volume Retention Manager function Attribute Attribute operation Normal end The operation has ended normally. Seq.
PAGE 298
{0x00:0x02,xxxxx,Error(9205-8122)},{0x00:0x03,xxxxx,Normal end}, {0x00:0x03,xxxxx,Normal end}],Num. of LDEVs=XXX [VRM] Volume Retention Manager function VTOC Volume Table of Contents (VTOC) operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 299
39 Volume Security (VSEC) function Set Group operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx,00:00,[VSEC],Set Group,,Normal end,Seq.
PAGE 300
Detailed information for this operation is shown in the following table. Table 281 Detailed information for Set Group operation Item Description Security Group The security group name. Host Group The host group name. LDEV Group The LDEV group name. Security The setting status of the security set to the security group. Enable, Disable The attribute of the security group.
PAGE 301
40 V Volume (VVOL) function Add V-Vol operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VVOL],Add V-Vol,,Normal end,Seq.=xxxxx +{V-VOL Group,Capa(blocks),CLPR,Type,Result}={{V1-1,4294967296,0,OPEN-V,Normal end}, ++{CU:LDEV,Capa(MB),SSID}={0x03:0x00,3287040,0x20},Num. of LDEVs=xxx +Num. of V-VOL Groups=xxx [VVOL] V Volume function Add V-Vol Add V-Vol operation Normal end The operation has ended normally. Seq.
PAGE 302
Item Description Num. of LDEVs The number of the created virtual volume. Num. of V-VOL Groups The number of created V-VOL group. Delete V-Vol operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VVOL],Delete V-Vol,,Normal end,Seq.=xxxxx +{V-VOL Group,Result}=[{V1-1,Normal End},{V1-2,Error(3205-3003)},{V1-3,Normal End}, {V1-4,Normal End}],Num. of V-VOL Groups=XXX [VVOL] V Volume function Delete-V-Vol Delete V-Vol operation Normal end The operation has ended normally. Seq.
PAGE 303
The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table. Table 284 Detailed information for Pool Change/Delete operation Item Description The operation to the pool. Command Change: Changing pool information Delete: Delete pool Pool ID Pool Type The pool ID of the pool where the settings have been changed or the number of the pool that have been deleted. The pool type.
PAGE 304
Pool Restore operation user-name,xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,[VVOL],Pool Restore,,Normal end,Seq.=xxxxx +{Pool ID, Result}=[{1,Normal end}, {2,Normal end },{2,Normal end},{128,Normal end}] Num. of Pools = 3 [VVOL] V Volume function Pool Restore Pool Restore operation Normal end The operation has ended normally. Seq.=xxxxxx Sequence number of the log entry (000000 to 999999) Detailed Information Detailed information for this operation is shown in the following table.
PAGE 305
Detailed information displays for this operation, as shown in the following table. Table 286 Detailed information for Pool SIM Comp Req operation Item Description SIM The reference code of the Service Information Message (SIM) generated in the storage system with resolved errors or service request status. 0xXXXXXX: Reference code of the SIM Num. of SIMs The number of SIMs with resolved errors and service request status.
PAGE 306
Item Description The result of the pool volume creation. LDEV Result Normal end: Normal end, Error(xxxx-yyyy): Abnormal end, Not Execute: Not Executed xxxx: Part code, yyyy: Error code Num. of LDEVs 306 The number of the created pool volume.
PAGE 307
41 XRCR function Set XRC Option operation root,99,2004/12/02,17:51:17:468,+09:00,[XRCR],Set XRC Option,,Normal End,Seq.=00020 +{CLPR,LV2THD(%),Block Option,Donot Block,LV1 Sleep,SleepTime(ms),LV1 SIM,LV2 Suspend}= [{00,50,Cache,Disable,Disable,100,Disable,Disable}, -{01,70,Cache,Enable ,Disable,10,Disable,Disable}, -{02,60,Cache,Disable,Disable, 10,Enable ,Enable }],Num. of CLPRs=32 [XRCR] XRCR function Set XRC Option Set XRC Option operation Normal end The operation has ended normally. Seq.
PAGE 308
Item Description LV2 Suspend Num. of CLPRs 308 XRCR function The status of the specified Level 2 Suspend. Enable, Disable The number of CLPRs.
PAGE 309
42 Support and other resources Related documentation The following documents provide related information: • HP StorageWorks XP glossary • HP StorageWorks External Storage user guide • HP StorageWorks LUN Configuration and Security Manager XP user guide for the XP12000/XP10000/SVS 200 • HP StorageWorks Data Integrity Check XP user guide You can find these documents on the HP Manuals website: http://www.hp.com/support/manuals In the Storage section, click Storage software and then select a product.
PAGE 310
• http://www.hp.com/go/storage • http://www.hp.com/support/manuals • http://www.hp.com/storage/spock Documentation feedback HP welcomes your feedback. To make comments and suggestions about product documentation, send a message to storagedocs.Feedback@hp.com. All submissions become the property of HP.
PAGE 311
A Audit log file output by function This appendix includes more detailed information about audit log file output. Table 289 lists audit log file output for operations that are common to all XP Command View functions. Table 290 lists audit log file output for each program option button on the XP Command View main pane.
PAGE 312
Table 290 Audit log file output by program option button Program product operation Buttons for launching options Tab Output of audit log file Operation Information Function name Operation name BASE Set System Info Set FTP Server Information / Status Audit Log Apply Audit Log SIM Complete Syslog Set Syslog Server Account LUNM LUNM (Note 3) LUN Sec 312 Audit log file output by function Command Device: Disable –> Enable Account Set User Account LUNM Set CommandDev Command Device: Enable
PAGE 313
Program product operation Buttons for launching options Tab Output of audit log file Operation Function name Operation name Clear Host Group Delete Host Group (Note 1) Paste (Host Group) Add Host Group (Note 1) Set Host Mode (Note 1) Add WWN (Note 1) Add LU Path (Note 1) Delete DKC WWN Delete DKC WWN (Note 1) “Drag & Drop” WWN node Add WWN (Note 1) Delete WWN (Note 1) Port (Note 4) Paste (LU Path) Add LU Path (Note 1) Add New iSCSI Target Add iSCSI Target (Note 1) (Note 2) Delete iSCSI Tar
PAGE 314
Program product operation Buttons for launching options Tab Output of audit log file Operation Operation name High Speed (2Port) Mode Set Speed Mode (Note 1) Fibre Addr.
PAGE 315
Program product operation Buttons for launching options LUSE Output of audit log file Tab Operation (Fibre) (Note 8) Specify Authentication Information Set FCSP Target (Note 1) (Note 2) Clear Authentication Information Set FCSP Target (Note 1) (Note 2) Authentication (Host Group): Disable –> Enable Set FCSP Target (Note 1) (Note 2) Authentication (Host Group): Enable –> Disable Set FCSP Target (Note 1) (Note 2) Add New Authentication Information Set FCSP Host (Note 1) (Note 2) Change Authent
PAGE 316
Program product operation Buttons for launching options Tab Output of audit log file Operation Function name Release LUSE (Note 1) Release LUSE VLL VLL Install CV VLL Install CV (Note 1) Volume to Space Volume to Space (Note 1) Volume Initialize Volume Initialize (Note 1) Make Volume Make Volume (Note 1) Blockade LDEV Volume-Blockade (Note 1) Restore Volume-Restore(N) (Note 1) Format Volume-Format (Note 1) Write to Control Blocks Volume-Format (H) (Note 1) Shredding SHRED Suspend
PAGE 317
Program product operation Buttons for launching options Performance Monitor Tab Output of audit log file Operation Function name Set Cache Residency (M/F Volume) Set M/F DCR (Note 1) (Note 2) Release Cache Residency (Open Volume) Delete Open DCR (Note 1) (Note 2) Release Cache Residency (M/F Volume) Delete M/F DCR (Note 1) (Note 1) Prestaging ON DCR Prestaging (Note 1) (Note 6) PCR PCR Set / Clear ENAS Set Cache Color (Note 1) Monitoring Options CurrentStatus Enable Gathering Interval PFM
PAGE 318
Program product operation Buttons for launching options Tab Output of audit log file Operation Function name Erase Migration History Port All Thresholds Operation name Del Migration Log SPM Set All Prior Port (Note 1) (Note 2) Set Ctrl Kind Set Prio Port (Attribute / Threshold / Upper) WWN Set Prior Port (Note 1) (Note 2) Set All Prior Port Initialize Default Set (Note 1) (Note 2) Delete ports if CHA is removed Clear PPC Info Set Ctrl Kind (Port Control) Set Ctrl Kind All Thresholds Set
PAGE 319
Program product operation Buttons for launching options Tab Output of audit log file Operation Function name PPCGrp Del/Chg (Note 1) (Note 2) SPM Group Change (ReName) Continuous Access XP Pair Operations Set All Prior WWN Set Ctrl Kind (WWN Control) Set Ctrl Kind (Note 1) (Note 2) Port-WWN Add Update Port WWN (Note 1) (Note 2) Port-WWN Delete Update Port WWN (Note 1) (Note 2) Initialize Default Set (Note 2) Delete ports if CHA is removed Clear PPC Info (Note 2) Paircreate CA Paircreate
PAGE 320
Program product operation Buttons for launching options Continuous Access XP Journal Tab Operation Function name Operation name Port Change (Target, Initiator, RCU Target) PORT Change Port Asynchronous Add CT Group CA Add CTG Operations CT Group Option Change CTG Option Delete CT Group Delete CTG Async Option Change Async Option Other Operations Option Change Option JNL Operation Edit JNL Volumes DKC Operation Pair Operation 320 Output of audit log file Audit log file output by
PAGE 321
Program product operation Buttons for launching options Business Copy XP TrueCopy - z/OS (R) Output of audit log file Tab Operation Optional Operation Change System Option Main Paircreate Function name Operation name System-Option (Note 1) BC Paircreate (Note 1) Pairsplit Pairsplit (Note 1) Pairresync Pairresync (Note 1) Pairsplit-E Pairsplit-E (Note 1) Pairsplit-S Pairsplit-S (Note 1) Change Reserve Change Reserve (Note 1) Initialize Initialize Option Option Option (Note 1) XP
PAGE 322
Program product operation Buttons for launching options Tab Output of audit log file Operation Function name Delete SSID Operation name Delete RCU Port Change (Target, Initiator, RCU Target) PORT Change Port Asynchronous Add CT Group TC z/OS (R) Add CTG Operations CT Group Option Change CTG Option Delete CT Group Delete CTG Async Option Change Async Option Run Script Operation Script Operations Stop Other Operations Universal Replicator - z/OS (R) JNL Operation DKC Operation 322
PAGE 323
Program product operation Buttons for launching options Tab Pair Operation Operation Function name Operation name Port Change (Target, Initiator, RCU Target) PORT Change Port Add Pair UR z/OS (R) Add-Pair (Note 1) Suspend Pair Suspend-Pair (Note 1) Resume Pair Resume-Pair (Note 1) Delete Pair Delete-Pair (Note 1) Change Pair Option Pair-Option (Note 1) Change System Option System-Option (Note 1) Clear SIM Clear-SIM (Note 1) EXCTG Operation Add JNLG to EXCTG, Remove JNLG from EXCTG
PAGE 324
Program product operation Buttons for launching options Mainframe Connection Tab Output of audit log file Operation Function name Delete CTG CTG (Note 1) FCv2 Set SCP Delay Time Set SCP Time (Note 1) Compatible PAV Add CPAV Add Alias (Note 1) Delete Alias (Note 1) Delete Volume Security Set Group VSEC Set Group (Note 1) Volume Retention z/OS (R) Attribute VRM Attribute (Note 1) Volume Table of Contents (VTOC) Serverless Backup Operation name VTOC (Note 1) XRC XRC Option XRCR Set
PAGE 325
Program product operation Buttons for launching options Tab Output of audit log file Operation Function name Operation name Delete-Lu (Force) (Note 1) Alternate Path (ADD / Delete / Priority UP / Priority Down) Alternate-Path (Note 1) Check Paths & Restore Vol.
PAGE 326
Program product operation Buttons for launching options Virtual Partition Manager Output of audit log file Tab Operation Function name Operation name Extend Release Cache (Note 1) Extend Release Cache/CLPR (Note 1) Partition Definition Apply (Create SLPR / Delete SLPR / Create CLPR / Delete CLPR / Paste CLPR, Port / Paste PG / SLPR Parameter / CLPR Parameter) VPM Set License Key Partition Definition Apply PP KEY SLPR PP Change Note 1 When you apply two or more settings of the same type to
PAGE 327
Operation Target of operation Priority Change Host Group 3 WWN 3 Changing Host Mode 3 Command Device 4 Command Dev. Security 4 LUN Security OFF: 3 ON: 1 If the priority is the same, the log information is output in the order of the operations performed. If you perform the following operations at the same time, the following happens: • • • • Add –> Delete: The operations cancel each other and no log information is output. Change –> Delete: Log information is output for the Delete operation.
PAGE 328
• Create LUSE volume 1 –> Create LUSE volume 2 –> Create LUSE volume 3 using LUSE volume 1 and LUSE volume 2 –> Delete LUSE volume 3: Log information is output only for the Create LUSE volume 1 operation and Create LUSE volume 2 operation. Note 6 The log information is output at the end, no matter when you perform the Cache Residency Manager operation. Note 7 Indicates the operation when iSCSI port is selected on the Authentication tab.
PAGE 329
Index A Add Alias, 69 Add CTG, 227, 237 Add Host Group, 85, 141 Add iSCSI Name, 86, 141 Add iSCSI Target, 86, 142 Add LU Path, 87, 143 Add Pair, 207, 238, 259 Add Path, 187 Add RCU, 188 Add V-Vol, 301 Add WWN, 88, 143 Add-Lu2, 271 Add-WWN, 272 All Config, 88 Alternate-Path, 273 Assist Config, 89 Attribute, 73, 297 audit logs acronyms, 51 Audit button, 23 downloading, 23 functions and operations, 39 introduction, 21 items, 32 purpose, 23 sample, 50 symbols, 33 Syslog tab, 24 types, 31 Auth Info (Host), 144 A
PAGE 330
Delete-Pair, 260 Disconnect-Paths, 277 Disconnect-Volume, 278 DKC WWN, 94 DKU Emulation, 97 document related documentation, 309 documentation HP website, 309 providing feedback, 310 Drive Interrupt, 168 E Edit-EXCTG, 261 End Shredding, 195 events Over MaxLine, 53 Over Threshold, 54 Exp R_TBL(Disable), 210 Exp R_TBL(Enable), 210 Expiration Lock, 74 F File, 183 File Install, 183 Force Reset, 98 Format, 99, 169 Format Stop, 100, 170 functions Account, 59 Audit Log, 53 Auto LUN (ALUN), 287 BASE, 61 Business
PAGE 331
J Journal-Option, 249, 262 Journal-Vol, 250, 251, 264, 265 L LUNM, 67 M M/F DCR, 112 Machine Install Date, 108 Make LUSE, 109, 165 Make Vol./Vol.
PAGE 332
Set Syslog Server, 55 Set System Info, 61 Set System Option, 125 Set TCP/IP Port, 164 Set User Account, 59 Set XRC, 307 SIM Complete, 56, 81 SIM Reporting Option, 81 Size Change, 174 Spare Disk, 175 Split Pair, 213 Start Pair, 247 Start Pair , 236 Subscriber's Choice, HP, 309 Suspend Pair, 214, 247 Suspend Shredding, 196 Suspend-Pair, 267 Switch SVP, 175 syslog items, 34 syslog information file component, 37 syslog server, 22 Syslog tab features, 25 System Tuning, 127 System-Option, 257, 268 T technical su