Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(4) (OL-14116-12, July 2009)
Table Of Contents
- Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(4)
- Contents
- Introduction
- Components Supported
- Software Download Process
- Determining the Software Version
- Downloading Software
- Selecting the Correct Software Image for an MDS 9100 Series Switch
- Selecting the Correct Software Image for an MDS 9200 Series Switch
- Selecting the Correct Software Image for an MDS 9500 Series Switch
- Migrating from Supervisor-1 Modules to Supervisor-2 Modules
- Configuring Generation 2 Switching Modules
- Upgrading Your Cisco MDS SAN-OS Software Image
- Upgrading Your Version of Cisco Fabric Manager
- General Upgrading Guidelines
- FICON Supported Releases and Upgrade Paths
- Upgrading with IVR Enabled
- Reconfiguring SSM Ports Before Upgrading to SAN-OS Release 3.3(4)
- Upgrading the SSI Image on Your SSM
- Upgrading a Switch with Insufficient Space for Two Images on the Bootflash
- Upgrading a Cisco MDS 9124 Switch
- Performing a Disruptive Upgrade on a Single Supervisor MDS Family Switch
- Upgrading an MDS 9222i Switch
- Downgrading Your Cisco MDS SAN-OS Software Image
- New Features in Cisco MDS SAN-OS Release 3.3(4)
- Limitations and Restrictions
- Upgrading to Recover Loss of Performance Manager Data
- Maximum Number of Zones Supported in Interop Mode 4
- Upgrading the SAN-OS Software on the MDS 9222i Switch
- Java Web Start
- Cisco Storage Media Encryption
- Cisco MDS 9222i Module Upgrade
- SANTap
- Deleting SANTap Configurations Is Required Before Downgrade
- FCIP Interoperability
- Applying Zone Configurations to VSAN 1
- Running Storage Applications on the MSM-18/4
- Compatibility of Fabric Manager and Data Mobility Manager
- A Supervisor-2 Module Might Reset in Switches Running SAN-OS Release 3.2(x)
- Limited ISSU Support on the MDS 9222i Switch
- Caveats
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
Send documentation comments to mdsfeedback-doc@cisco.com
13
Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(4)
OL-14116-12
Upgrading Your Cisco MDS SAN-OS Software Image
java -Xms512m -Xmx512m -jar m9000-fm-3.3.4.jar
Step 5 Follow the onscreen instructions provided in the Fabric Manager management software setup wizard.
Installing Fabric Manager on Windows
This section describes how to install Fabric Manager on Windows.
Note Fabric Manager Server can not be installed on an Active Directory Server when using PostgreSQL,
Fabric Manager servers are domain controllers and can not create local PostgreSQL user accounts.
If your server is running Terminal Services in Application mode, or if you are running Citrix Metaframe
or any variation thereof, you need to issue the following command on the DOS prompt before installing
Fabric Manager Server.
1. Open a command-line prompt: Start > Run, then type cmd and press Return.
2. At the command prompt type: user /install.
Note Do not close the command line window. This must remain open for the entire duration of the
install.
The following is an example of the output of this command:
C:\Documents and Settings\user.domain>USER /INSTALL
User session is ready to install applications.
3. Follow all steps needed to install Fabric Manager, Fabric Manager Server, and Device Manager. See
the instructions later in this section.
4. When the installation is complete, at the command prompt, type user /execute and press Return.
Then type exit and press Return.
The following is an example of the output of this command:
C:\Documents and Settings\user.domain>USER /execute
User session is ready to execute applications.
To install Fabric Manager on Windows, follow these steps:
Step 1 Click the Install Management Software link.
Step 2 Choose Management Software > Cisco Fabric Manager.
Step 3 Click the Installing Fabric Manager link.
Step 4 Select the drive for your CD-ROM.
Step 5 Click the FM Installer link.
Step 6 Follow the onscreen instructions provided in the Fabric Manager Installer 3.3(4).
To install Device Manager on your workstation, follow these steps: