HP SureStore 300mx / 600mx / 700mx Optical Jukebox User’s Guide Edition 1 HP Part No.
Notice This document contains information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. The information contained in this document is subject to change without notice.
Typographical Conventions The following typographical conventions are used in this manual: Emphasis: Denotes important information. Keycap: Keys on the library. Computer Output: Information displayed in the display window and screen menu items that you can select. WARNING Warnings call attention to a procedure or practice that could result in personal injury if not correctly performed. Do not proceed until you fully understand an meet the required conditions.
In This Manual This user’s guide includes: Chapter 1 set-up information for this optical jukebox Chapter 2 information about choosing and using optical disks Chapter 3 features description, operating instructions, and troubleshooting information Appendix A supplies and customer support Appendix B operating this jukebox on a SCSI bus Appendix C safety and regulatory information Glossary of Terms Index iv
Contents 1. Setting Up the Jukebox Overview of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 What you need to set up the jukebox: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Choosing a Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 System Components Needed for Operation of This Jukebox . . . . . . . . . . . . . . . . 1-3 Standard Configuration . . . . . . . . . . . . . .
Contents 3. Operating the Jukebox Overview of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Operating the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Using Selection Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Understanding Display Window Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Top Level Menus . . . . . . .
Contents Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-7 B. Operating This Jukebox on a SCSI Bus A Brief Overview of SCSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2 The SCSI Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents English Translation of Finland Regulatory Information . . . . . . . . . . . . . . . . . . . . C-9 Japanese VCCI Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures Figure 1-1 . Right Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Figure 1-2 . Left Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Figure 1-3 . Connecting the Jukebox as the Only Peripheral. . . . . . . . . . . . . . . . 1-10 Figure 2-1 . Recommended Placement of Cartridge Labels . . . . . . . . . . . . . . . . . 2-4 Figure 2-2 . Write-Protect Button Location . . . . . . . . . . . . . . . . .
Figures x
Tables Table 1-1. Maximum SCSI External Cable Lengths (Assuming no devices internal to the host computer) . . . . . . . . . . . . . . . . . . . . 1-8 Table 3-1. Configuration Choices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20 Table 3-2. Information Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22 Table 3-3. Internal Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27 Table 3-4.
Tables xii
Chapter 1: Setting up Setting the DiskupDrive the Jukebox Setting Up the Jukebox 1
Setting Up the Jukebox Overview of This Chapter Overview of This Chapter This chapter gives information on the following topics: • what you need to set up the jukebox • choosing a proper environment for the jukebox • identifying features on the jukebox side panels • connecting the jukebox to your computer • connecting power • moving and shipping the jukebox What you need to set up the jukebox: • power cord (included) • single-ended and differential SCSI terminators (included) • SCSI cable
System Components Needed for Operation of This Jukebox This jukebox requires application software to operate it as a single storage device composed of multiple SCSI devices. Consult with your sales representative to chose the application software you need. Standard Configuration The following list shows the hierarchy of the system components needed to operate this jukebox in a standard configuration.
Setting Up the Jukebox Identifying Controls and Features Identifying Controls and Features Figure 1-1 Right Side 1-4 Chapter 1
The numbers below correspond to the numbers in Figure 1-1 on the previous page: 1 Control panel Used to manually control and monitor operation of the jukebox. A full description of the controls and indicators on the control panel are in Chapter 3. 2 Mailslot Used to load and eject optical disks. 3 Power switch Used to power the jukebox on and off. 4 Right service access panel A service panel that should be removed only by your service representative.
Setting Up the Jukebox Identifying Controls and Features Figure 1-2 Left Side 1-6 Chapter 1
5 Active bus indicator Lit when the SCSI bus is active. There is an indicator for the single-ended interface and an indicator for the differential interface 6 SCSI interface selection switch Used to select either the single-ended or differential SCSI interface. 7 SCSI ports Used for attaching the SCSI cable from the jukebox to the host computer. Select either the single-ended or the differential pair of connectors (see item 5 in this list). Both ports of a selected interface must be used.
Setting Up the Jukebox Connecting the SCSI Cables to the Jukebox Connecting the SCSI Cables to the Jukebox The following is general cabling information. Interface types available Single-ended or differential SCSI, selected by the interface selection switch on the top of the interface module (see “6” on Figure 1-2). Number of hosts This jukebox may be used in high availability environments. High availability environments can be complex and are not described in this guide.
Choosing Your Cabling Configurations Pick the configuration that applies to your plans below. You will be shown the page for the proper procedures.
Setting Up the Jukebox Connecting the Jukebox as the Only Peripheral Connecting the Jukebox as the Only Peripheral NOTE This following configuration is the recommended configuration for this jukebox. Figure 1-3 Connecting the Jukebox as the Only Peripheral Refer to Figure 1-1 and 1-2 for the locations of the following switches and connectors. 1. Ensure the power to the host computer is turned off. 2.
4. Connect a cable between the host computer and one of the jukebox SCSI connectors of your selected interface type. You may connect the SCSI cable to either port of the jukebox. NOTE Plug a terminator into the unused port of the interface type you are using. Also, put a terminator on one of the port connectors of the other interface type. The single-ended terminator has 50 pins, the differential terminator has 68 pins. NOTE Go to “Connecting Power” and then to “Write Verify” to finish installation.
Setting Up the Jukebox Connecting the Jukebox with Other SCSI Devices Connecting the Jukebox with Other SCSI Devices NOTE Operating this jukebox with other peripherals on the same bus is supported, but not recommended. In most circumstances, the recommended configuration for this jukebox is as the only device on a SCSI bus. However, your use of the jukebox may be such that other devices could be connected to the bus without a loss of performance.
Connecting Power 1. Ensure the power switch on the jukebox is OFF (see Figure 1-1).) NOTE Use the power cord shipped with the jukebox. 2. Plug the socket end of the power cord into the power port on the bottom of the interface enclosure (see “8” on Figure 1-2). 3. Plug the other end of the power cord into a power outlet. 4. (After the jukebox is moved to its operating location) Lower the leveler feet and tighten the 1/2-inch nut on each foot. 5. Turn the power on.
Setting Up the Jukebox Configuring Write Verify Configuring Write Verify The write verify configuration ensures that data is written reliably to an optical disk. The jukebox ships with write verify enabled. Many software applications also default to this method of writing. Writing data on a magneto-optical disk requires two passes. The first pass erases the data in the sector to which data will be written. The second pass writes new data to that sector.
Moving or Shipping the Jukebox If you want to move the jukebox a short distance, such as to another office or to another floor in your building, see “Moving the Jukebox a Short Distance.” If you want to ship the jukebox to another location, see “Shipping the Jukebox.” Moving the Jukebox a Short Distance 1.
Setting Up the Jukebox Moving or Shipping the Jukebox Shipping the Jukebox 1. Follow your jukebox application software instructions for unmounting and ejecting disks. Ensure that there are no disks in the drives. CAUTION Failure to eject a disk from the optical drive prior to moving the jukebox could result in damage to the optical drive mechanism. Failure to remove all disks from the storage slots in the jukebox could result in damage to the jukebox.
Using Optical Disks 2 Using Optical Disks
Using Optical Disks Overview of This Chapter Overview of This Chapter Using Optical Disks The optical disks that you use with your jukebox are an integral part of the storage process.
Using Optical Disks Choosing an Optical Disk Type Choosing an Optical Disk Type To choose which type of disks to use, consider these points: NOTE • Rewritable optical disks--data can be repeatedly written and erased. • Write-Once optical disks--data can be written only once, and the data cannot be altered or erased. If you have a need for data security and audit trails, write-once disks may be a good disk choice.
Using Optical Disks Labeling an Optical Disk Cartridge Labeling an Optical Disk Cartridge Make it a practice to label your optical disk cartridges. You are provided adhesive labels with each disk for this purpose. Here are some suggestions for labeling: NOTE Your jukebox application software may label your optical disk slot locations differently. Use your application to check disk locations prior to labeling the disks. • storage slot location (1, 2, 3, ...
Using Optical Disks Write-Protecting an Optical Disk Write-Protecting an Optical Disk Using Optical Disks Each side of an optical disk can be write-protected by sliding the write-protect button in the direction of the arrow on the cartridge (see Figure 2-2). With rewritable optical disks, write-protecting the disk prevents overwriting existing files and prevents any additional file being written to the disk.
Using Optical Disks Caring for Optical Disks Caring for Optical Disks Follow these guidelines to ensure that your optical disks remain in good condition: • Do not expose disks to extreme magnetic fields. • Do not expose disks to dust particles. • Do not expose disks to extreme temperatures or extreme humidity. • Do not drop the disks. • Do not open a disk's metal shutter and touch the disk surface. • Do not take disks apart. • Do not insert disks with loosely-attached labels into the jukebox.
Operating the Jukebox 3 Operating the Jukebox
Operating the Jukebox Overview of This Chapter Overview of This Chapter This chapter gives information on the following topics: • operating the control panel • using the selection buttons • interpreting messages which appear in the display window • loading optical disks into the jukebox • ejecting optical disks from the jukebox • entering the administration menu password • changing the administration menu password • setting SCSI IDs or logical unit numbers (LUNs) • setting configurations
Operating the Jukebox Operating the Control Panel Operating the Control Panel The control panel enables manual control of all jukebox operations using four buttons and an LED display. The SCSI IDs of the jukebox and its optical drives can be set and changed, disks may be loaded and ejected, configurations can be monitored and changed, performance information can be viewed, internal tests can be run, and the jukebox can be secured from unauthorized use.
Operating the Jukebox Operating the Control Panel Figure 3-1 The Jukebox Control Panel 3-4 Chapter 3
Operating the Jukebox Operating the Control Panel The numbers below refer to the numbers in Figure 3-1 on the previous page. 1 Swivel feature The control panel assembly may be rotated to face the display (#3 below) toward the front or right side of the jukebox. The front has the vertical window, the right side has the mailslot.
Operating the Jukebox Operating the Control Panel Figure 3-2 Jukebox Display Menu Tree 3-6 Chapter 3
Operating the Jukebox Using Selection Buttons Using Selection Buttons Use the CANCEL, PREV, NEXT, and ENTER buttons to select tasks you want the jukebox to perform. When you push these buttons, the message in the display window changes. See the next section for a list of messages. NOTE You can get back to READY at any time by pressing CANCEL. (You may have to press CANCEL more than once in some cases.
Operating the Jukebox Understanding Display Window Messages Understanding Display Window Messages The display window shows the operations you may select. Instructions for selecting or changing choices follows the explanation of the messages. Top Level Menus NOTE READY The jukebox is ready for operation. ADMIN * Select to access second-level choices. You must enter a security code to access these choices. A * indicates that there are multiple selections available for that choice currently displayed.
Operating the Jukebox Understanding Display Window Messages In Figure 3-2, you can display the selections listed in boxes below the shaded choices by pressing ENTER when one of the shaded choices displays. Press PREV or NEXT to scroll through the list. To perform the displayed operation, press ENTER.
Operating the Jukebox Loading a Disk into the Jukebox Loading a Disk into the Jukebox NOTE Label all disks before loading them into the jukebox. (See “Labeling an Optical Disk Cartridge” in Chapter 2 for instructions.) Some software packages require that you load and eject disks by using instructions in the software. If you use a software package to manage files in the jukebox, check the software documentation before proceeding with these steps. Start with READY or LOAD in the display.
Operating the Jukebox Loading a Disk into the Jukebox 3. LOADING displays as the jukebox moves the disk to the slot. After the disk is loaded into the selected storage slot, the display returns to LOAD *. You may now load additional disks by inserting the disks into the mailslot and repeating step 3 until you are finished loading disks. 4. Press CANCEL to return to the READY state.
Operating the Jukebox Ejecting a Disk From the Jukebox Ejecting a Disk From the Jukebox NOTE Some software packages require that you load and eject disks by following the instructions in the software. If you use a software package to manage files in the jukebox, check the software documentation before proceeding with these steps. Start with READY in the display. 1. Press NEXT until EJECT * displays and then press ENTER. 2. EJECT SLOT # displays.
Operating the Jukebox Entering the Administration Menu Password Entering the Administration Menu Password READY > ADMIN * > PSWD 000 000 000 A numeric password is required to access menu choices beneath the ADMIN * menu of the jukebox (see Figure 3-2). A three-part password, 000-000-000, was set at the factory. Consider changing this default password to your own password so that only authorized persons can access the choices under the ADMIN * menu. NOTE Follow these steps to enter the password.
Operating the Jukebox Changing the Administration Menu Password Changing the Administration Menu Password READY > ADMIN * > PSWD 000 000 000 >CONFIG * 1. Follow the steps on the previous page to enter your password (or the default, factory-set password 000 000 000). 2. TEST * displays. Press NEXT until CONFIG * displays, and then press ENTER. 3. Press NEXT or PREV or until NEW PASSWORD displays and then press ENTER. 4. NEW 000 000 000 displays and the first set of three zeros flashes.
Operating the Jukebox Setting the SCSI IDs Setting the SCSI IDs NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B. First, determine if you are using basic SCSI addressing or logical unit numbering (LUN). Setting the LUN mode is explained below. Tables showing default SCSI IDs for basic SCSI addressing and LUN addressing are in Appendix B.
Operating the Jukebox Setting the SCSI IDs You may now view the SCSI ID and LUN numbers using VIEW ID’S, or set a new SCSI ID number using SET ID’S. (See the following two sections.) Viewing the Current SCSI IDs READY > ADMIN * > SCSI ID’S * > VIEW ID’S * > NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B. Start with READY in the display. 1. Press NEXT until ADMIN * displays, and then press ENTER. 2. Enter the administration password.
Operating the Jukebox Setting the SCSI IDs Changing the Current SCSI IDs READY > ADMIN * > SCSI ID’S * > SET ID’S * NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B. Start with READY in the display. 1. Press NEXT until ADMIN * displays, and then press ENTER. 2. Enter the administration password. 3. Press NEXT until SCSI ID’S displays, and then press ENTER. 4. VIEW ID’S displays. Press NEXT until SET ID’S displays and then press ENTER.
Operating the Jukebox Setting the SCSI IDs If your host computer system does not support multiple types at the same ID and you want to use LUN mode, you must select different IDs for the jukebox controller (JKBX ID #) and the drives (DRV #). Tables in Appendix B show jukebox default settings and an example of setting the jukebox controller and drives to different IDs (one digit apart). If another device ID is placed between the jukebox controller and the drives, problems can result.
Operating the Jukebox Setting an Operating Configuration Setting an Operating Configuration READY > ADMIN * > CONFIG * You can set configurations to customize the way the jukebox operates. Start with READY in the display. 1. Press NEXT until ADMIN * displays. 2. Enter the administration password. 3. TEST * displays. Press NEXT until CONFIG * displays, and then press ENTER. 4. Press NEXT or PREV until the name of the configuration you wish to set displays and then press ENTER.
Operating the Jukebox Setting an Operating Configuration Table 3-1 Configuration Choices Configuration Name Description RECOVERY ON/OFF Toggles between ON and OFF. If the configuration is set to ON, the jukebox attempts to recover from errors; if the configuration is set to OFF, the jukebox immediately stops moving if an error condition occurs. The default configuration is RECOVERY ON, and recovery should remain ON under normal conditions.
Operating the Jukebox Setting an Operating Configuration Configuration Name Description Toggles between ON and OFF. The ON configuration disables loading and ejecting disks. The OFF configuration enables loading and ejecting disks (the default state of the jukebox). SECURE MAIL OUT/IN Toggles between OUT and IN. Determines the orientation of the mailslot when the SECURE configuration is set to ON. When set to OUT, the mailslot remains in its normal orientation.
Operating the Jukebox Retrieving Log History Retrieving Log History > READY ADMIN * > INFO * You can display information stored in the jukebox operating logs by using the INFO * menu. Start with READY in the display. 1. Press NEXT until ADMIN * displays. 2. Enter the administration password. Instructions for entering this password are in “Entering the Administration Menu Password” in this chapter. 3. TEST * displays. Press NEXT until INFO * displays, and then press ENTER. 4.
Operating the Jukebox Retrieving Log History Log Name Description JKBX ODOMETERS * Press ENTER to select the odometer logs described in the next five rows. HOURS MOVES Number of operation hours (time the power was on). Some of the time may be while in power reduction mode. Total moves and move attempts by the disk transport mechanism. Total disk transport mechanism flips. XLATES Total disk transport mechanism horizontal moves. ROTATES Total mailslot rotations.
Operating the Jukebox Retrieving Log History Log Name SOFT ERROR * Description Log of recovered errors (commands that complete successfully). Returns either NO SOFT ENTRIES or ENTRY #. (There may be multiple soft error numbers.) Press ENTER to view the log for the currently displayed error, or press NEXT to select the next error. (Log entries are described in the rows following RECOVERY ERROR * in this table.) RECOVERY ERROR * Log of errors during the most recent move.
Operating the Jukebox Retrieving Log History Log Name Description Element number to which the source refers. (This information is valid for MOVE, EXCHANGE, and POSITION movements only.) DESTINATION 1 Element to which the first destination refers. (This information is valid for MOVE and EXCHANGE movements only.) DESTINATION 2 Element to which the second destination refers. (This information is valid for the EXCHANGE movement only.) ODOMETER # Move number in which the error occurred.
Operating the Jukebox Running an Internal Test Running an Internal Test READY > ADMIN * >TEST * The optical jukebox can run self-diagnostic tests. See the Caution note below. CAUTION Some of the internal diagnostic tests of this jukebox can corrupt your file system if not properly completed (for example, disks can be placed in unexpected locations). In almost all cases, these tests should be run only by authorized service personnel.
Operating the Jukebox Running an Internal Test Table 3-3 Internal Tests Test Name Description Internal Tests are normally for service use only. Some of the following tests can corrupt your data if not completed properly. Those tests are noted with a “Used by service...” alert. Do not run these tests. EXCHANGE DEMO Used by service personnel only. Do not run this test if the jukebox contains disks with file system data on them.
Operating the Jukebox Running an Internal Test Test Name Description MAGAZINE IO Makes a combination of moves with a PASS/FAIL result. It moves an optical disk from a randomly-chosen full slot to a randomly-chosen empty slot with a random flip. It then moves the disk back to its original storage slot with its original orientation. This test displays FAIL if there are no disks in the jukebox or if all storage slots are full. The drives and mailslot must be empty.
Operating the Jukebox Running an Internal Test Test Name Description Calibrates the disk transport mechanism, establishes the mechanism’s orientation, and determines the reference points in the picker travel path. Assumes that the mechanics and servo system are functional. No disks are required. FIND VERT HOME Recalibrates the vertical position of the disk transport mechanism and verifies that the vertical path is clear. No disks are required.
Operating the Jukebox Running an Internal Test Test Name Description EXERCISE MECH Runs the VERTICAL TEST, TRANSLATE TEST, FLIP TEST, MAGAZINE IO, DRIVE IO, and MAILSLOT IO tests. Each test runs one time per test loop. WELLNESS TEST Checks the general capability of the jukebox. Requires one loaded disk. The drives, transport, and mailslot must be empty. Runs INIT MECHANICS and EXERCISE MECHANICS. Each test runs one time per test loop. CLEAR SOFT LOG Sets the soft error log to zero.
Operating the Jukebox Running an Internal Test Description BOTTOM THUMB Used by service personnel only. Reports THUMB A, THUMB B, or NO THUMB. Looks at the top and bottom thumb sensors and reports whether the thumbs on the disk transport mechanism are in the forward or back position. If THUMB A or THUMB B is returned, the specified thumb is the forward position. If NO THUMB is returned, both thumbs are in the back position. TOP THUMB Used by service personnel only.Reports ON or OFF.
Operating the Jukebox Using Online Repair Using Online Repair The online repair selection allows an authorized service representative to replace a faulty drive while the jukebox remains online and active. This feature is available only if enabled by your jukebox application software. CAUTION Selecting online repair should be done only by an authorized service representative. This procedure could cause the jukebox optical drives to become inactive.
Operating the Jukebox Troubleshooting Troubleshooting This section provides steps you can take when problems occur during operation. If the troubleshooting procedures do not resolve the problem, call your service provider. If you do not have a service provider, you can locate one by going to ww.hp.com. Look under “HP Services and Support.
Operating the Jukebox Troubleshooting Table 3-4 Troubleshooting Problem Jukebox won’t power on. Poweron selftest failed and DEVICE FAILED displays What to do • Ensure that power cord connections are tight. • Ensure that the power switch is ON (located on the lower right side of the jukebox rear panel). • Ensure that the power outlet is operating. • Replace the power cord with a known good one. • If steps above are unsuccessful, call your service representative. • Power cycle the jukebox.
Operating the Jukebox Troubleshooting Problem No display messages. What to do • Ensure that the power cord is connected. • Ensure that the power switch is ON. • Power cycle the jukebox.* • If steps above are unsuccessful, call your service representative. Some computers require a restart to recognize new SCSI IDs. • Ensure the SCSI bus is inactive and restart your host computer. Forgot your password. • Enter the default password (000 000 000).
Operating the Jukebox Troubleshooting Problem What to do Disk inserted in the mailslot but MAILSLOT EMPTY displays The mailslot sensors do not detect a disk in the mailslot. Disk inserted in the mailslot but DEST NOW FULL displays The jukebox moved a disk into the slot you chose before your load command executed. Disk inserted in the mailslot but TRANSPORT FULL displays The disk transport mechanism already contains a disk.
Operating the Jukebox Troubleshooting Problem Disk eject attempted but RESERVED displays. What to do The jukebox application software reserved the element for its use or a security configuration was set to prevent disk ejection. • If appropriate, change this setting See “Setting an Operating Configuration” in this chapter. The current administration password is required. This is not an error. There are no disks in the jukebox. Disk eject attempted but TRANSPORT FULL displays.
Operating the Jukebox Troubleshooting Problem RUN ISTAT TEST displays (this initializes the element status) Can't write to the disk. What to do • Power cycle the jukebox.* • Run the INIT ELEM STATUS test under the TEST * menu • If steps above do not result in a READY display, call your service representative. • Check the host file system access permissions. • Eject the disk and check that the write-protect tab on each side of the disk is in the write-enabled position.
Supplies and Customer Support A Supplies and Customer Support
Supplies and Customer Support Overview of This Appendix Overview of This Appendix This appendix provides information on the following topics: • supplies and accessories • shipping screw specifications • HP customer support A-2 Appendix A
Supplies and Customer Support Supplies and Accessories Supplies and Accessories A full range of computer supplies may be ordered through a Hewlett-Packard authorized dealer, sales office, or online through the Business Store at www.bstore.hp.com. You may also access the “Business Store” web site by selecting “Other Ways to Buy” from the main HP shopping site, www.shopping.hp.com. Authorized dealers and sales offices can be found at www.hp.com under “HP Service and Support.
Supplies and Customer Support Supplies and Accessories Item HP Part Number Rewritable optical disk (1,024 bytes/sector, 4.7 Gbytes, single disk) 88143J Write-once optical disk (1,024 bytes/sector, 4.7 Gbytes, single disk) 88145J 2.6- and 2.3-Gbyte Optical Disks Rewritable optical disk (1,024 bytes/sector, 2.6 Gbytes, single disk) 92280F Write-once optical disk (1,024 bytes/sector, 2.6 Gbytes, single disk) 92290F Rewritable optical disk (512 bytes/sector, 2.
Supplies and Customer Support Supplies and Accessories Item HP Part Number 68-Pin High-Density to 50-Pin Low-Density 1.0 (3.3 ft) bail to thumb screw C2915A 2.0 m (6.5 ft) thumb screw to thumb screw C2906A 5.0 m (16.5 ft) thumb screw to thumb screw C2907A 20.0 m (65.6 ft) thumb screw to thumb screw C2916A 68-Pin High-Density to 68-Pin High-Density C2911A 2.5m (8.2 ft) thumb screw to thumb screw C2924A 10.0 m (32.8 ft) thumb screw to thumb screw C2925A 20.0 m (65.
Supplies and Customer Support Hewlett-Packard Customer Support Hewlett-Packard Customer Support If your jukebox fails and the suggestions in this user’s guide and accompanying documentation do not solve your problem: NOTE • If you have a service contract with HP, contact your local HP Response Center. Response Centers are found at www.hp.com under the “HP Services and Support” tab. • If you do not have a service contract with HP, contact your nearest HP dealer or sales office.
Supplies and Customer Support Warranty Warranty HP PRODUCT C1150M/P, C1160M/P, C1170M/P DURATION OF WARRANTY One Year 1. HP warrants HP hardware, accessories and supplies against defects in materials and workmanship for the period specified above. If HP receives notice of such defects during the warranty period, HP will, at its option, either repair or replace products which prove to be defective. Replacement products may be either new or like-new. 2.
Supplies and Customer Support Warranty 8. HP will be liable for damage to tangible property per incident up to the greater of $300,000 or the actual amount paid for the product that is the subject of the claim, and for damages for bodily injury or death, to the extent that all such damages are determined by a court of competent jurisdiction to have been directly caused by a defective HP product. 9.
Supplies and Customer Support Warranty Supplies and Customer Support Appendix A A-9
Operation on a SCSI Bus B Operating This Jukebox on a SCSI Bus
Operating This Jukebox on a SCSI Bus A Brief Overview of SCSI A Brief Overview of SCSI General The Small Computer System Interface (SCSI), is a contention-based bus that accommodates different speed devices without impacting the devices with faster transfer speeds. This specification was defined by the American National Standards Institute (ANSI) in 1986. The specification defines both the physical medium and the command set used to transfer information.
Operating This Jukebox on a SCSI Bus A Brief Overview of SCSI an ID greater than 7, would always assume it won the contention and would attempt to talk, perhaps at the same time as a device with an ID above 7 that was contending for the bus. The following diagram shows the priority scale of IDs when the priority of the two blocks of eight are reversed.
Operating This Jukebox on a SCSI Bus A Brief Overview of SCSI To use this form of addressing, however, the jukebox application software, the SCSI bus drivers and the host adapter firmware all have to support this mode of addressing. The following diagram shows LUNs assigned to devices within the device at ID 6. Transfer Rates on the Bus Termination To keep signals on the SCSI bus from being reflected, “terminators” must be placed at each end of the physical bus.
Operating This Jukebox on a SCSI Bus A Brief Overview of SCSI Termination is always at both physical ends of the bus. Single-ended and Differential Interfaces The SCSI bus is electrically implemented in two ways: single-ended and differential. These terms come from the way the signals are asserted on the bus. Single-ended buses use a 5-volt signal that is referenced to ground. This method makes the bus somewhat susceptible to noise and loss of signal quality over distance.
Operating This Jukebox on a SCSI Bus A Brief Overview of SCSI • This connector is similar to a D-type connector, but smaller and with smaller pin holes placed closer together. • 50-pin low-density ribbon (usually internal to the host) Wide devices (68- pin) use the following connectors: • 68-pin high density Micro D connector (external) This connector is similar to a D-type connector, but longer and slimmer and with smaller pin holes placed closer together. This connector is becoming the most common.
Operating This Jukebox on a SCSI Bus The SCSI Bus and This Jukebox The SCSI Bus and This Jukebox This jukebox is a “fast and narrow” SCSI device with the capability to connect to either a narrow single-ended bus or a wide differential bus. In the diagram below, note that the single-ended (50-line) bus is brought directly onto the jukebox internal narrow bus.
Operating This Jukebox on a SCSI Bus The SCSI Bus and This Jukebox Adding Devices to the Bus When considering adding other devices to the jukebox bus, you should consider the following: • Will adding a device onto a bus with this jukebox interfere or degrade the performance of the jukebox or the device that is added? • If the decision is made to add other devices to the jukebox bus, what SCSI requirements must be observed to make sure the bus will work? Before addressing some questions involved in deci
Operating This Jukebox on a SCSI Bus The SCSI Bus and This Jukebox This method should only be implemented by an experienced systems integrator who is highly knowledgeable about SCSI. Since the wide (68-pin) buses need more data lines on the bus for their data transfer, it’s necessary that the cables connecting the devices are 68 pin. The data would be lost if the devices were set up as depicted in the figure below.
Operating This Jukebox on a SCSI Bus The SCSI Bus and This Jukebox It is very important that the 68-pin to 50-pin cable is properly configured to assure that the eighteen truncated lines are properly terminated. Cable Lengths Observe SCSI cable maximum lengths; - 3 meters (9.8 feet) for the single-ended bus (remember, this is a fast device) - 25 meters (82 feet) for the differential bus. Termination Refer to the documentation that comes with your particular adapter to see how to apply termination.
Operating This Jukebox on a SCSI Bus The SCSI Bus and This Jukebox General • Do not connect a single-ended bus to a differential bus. Damage can occur.
Operating This Jukebox on a SCSI Bus Default SCSI IDs in the Jukebox When Using Basic SCSI Addressing and When Using LUN Mode Default SCSI IDs in the Jukebox When Using Basic SCSI Addressing and When Using LUN Mode Table B-1 Default SCSI and LUN Settings LUN Mode OFF LUN Mode ON ID LUN ID LUN JKBX ID 6 0 6 0 DRV 1 ID 5 0 6 1 DRV 2 ID 4 0 6 2 DRV 3 ID* 3* 0* 6* 3* DRV 4 ID* 2* 0* 6* 4* * 600mx models only Operation on a SCSI Bus Appendix B B-12
Operating This Jukebox on a SCSI Bus Default SCSI IDs in the Jukebox When Using Basic SCSI Addressing and When Using LUN Mode Table B-2 LUN Mapping if “DRVs” SCSI ID is Changed to an ID Different Than the Jukebox (IDs used here are an example) LUN Mode ON ID LUN JKBX ID 5 0 DRV 1 ID 6 0 DRV 2 ID 6 1 DRV 3 ID* 6* 2* DRV 4 ID* 6* 3* * 600mx models only B-13 Appendix B
Operating This Jukebox on a SCSI Bus Default SCSI IDs in the Jukebox When Using Basic SCSI Addressing and When Using LUN Mode Figure B-2 Two or Four Drives, Basic SCSI Addressing Displays on the Control Panel Operation on a SCSI Bus Under CHOOSE LUN MODE * menu >> LUN MODE OFF Under SCSI IDs * menu >> JXBX ID 6 LUN 0 DRV 1 ID 5 LUN 0 DRV 2 ID 4 LUN 0 DRV 3 ID 3 LUN 0 (if installed) DRV 4 ID 2 LUN 0 (if installed) Appendix B B-14
Operating This Jukebox on a SCSI Bus Default SCSI IDs in the Jukebox When Using Basic SCSI Addressing and When Using LUN Mode Figure B-3 Two or Four Drives, LUN Addressing, Controller/Drives Use Same ID Displays on the Control Panel Under CHOOSE LUN MODE * menu >> LUN MODE OFF Under SCSI IDs * menu >> JXBX ID 6 LUN 0 DRV 1 ID 6 LUN 1 DRV 2 ID 6 LUN 2 DRV 3 ID 6 LUN 3 (if installed) DRV 4 ID 6 LUN 4 (if installed) B-15 Appendix B
Operating This Jukebox on a SCSI Bus Default SCSI IDs in the Jukebox When Using Basic SCSI Addressing and When Using LUN Mode Figure B-4 Two or Four Drives, LUN Addressing, Controller/Drives Use Different IDs Displays on the Control Panel Under SCSI IDs * menu Operation on a SCSI Bus Under CHOOSE LUN MODE * menu >> LUN MODE OFF >> JXBX ID 6 LUN 0 DRV 1 ID 5 LUN 0 DRV 2 ID 5 LUN 1 DRV 3 ID 5 LUN 2 (if installed) DRV 4 ID 5 LUN 3 (if installed) Appendix B B-16
Operating This Jukebox on a SCSI Bus Default SCSI IDs in the Jukebox When Using Basic SCSI Addressing and When Using LUN Mode Table B-3 Possible Additional SCSI Addresses Available No. of Drives LUN mode OFF (Basic SCSI Addressing) 2 4 IDs are available for connecting other devices. 4 2 IDs are available for connecting other devices.
Safety and Regulatory Information Safety and Regulatory Information C
Safety and Regulatory Information Overview of this Appendix Overview of this Appendix This appendix contains important safety and regulatory information for the United States, Finland, Sweden, Germany, United Kingdom, European Union, and Japan.
Safety and Regulatory Information CDRH Regulations (USA Only) CDRH Regulations (USA Only) The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States.
Safety and Regulatory Information EC Radio Frequency Interference Statement (Europe Only) EC Radio Frequency Interference Statement (Europe Only) WARNING This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Safety and Regulatory Information United Kingdom Telecommunications Act 1984 United Kingdom Telecommunications Act 1984 The Hewlett-Packard 300mx, 600mx and 700mx jukeboxes are approved under Approval Number NS/G/1234/J/100003 for indirect connection to Public Telecommunication Systems within the United Kingdom.
Safety and Regulatory Information Declaration of Conformity Declaration of Conformity C-6
Safety and Regulatory Information Herstellerbescheinigung Herstellerbescheinigung Diese Information steht im Zusammenhang mit den Anforderungen der Maschinenlärn information sverordnung vom 18 Januar 1991. Schalldruckpegel Lp < 70 dB(A) • am arbeitsplatz • normaler betrieb • nach ISO 7779:1988/EN 27779:1991 (Typprüfung) English Translation of German Sound Emission Directive This statement is provided to comply with the requirements of the German Sound Emission Directive, from 18 January 1991.
Safety and Regulatory Information Turvallisuusyhteenveto Turvallisuusyhteenveto Laserturvallisuus LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT Hewlett-Packard 300mx, 600mx, 700mx optiset levymuistiasemat ovat käyttäjänmx kannalta turvallisia luokan 1 laserlaitteita. Normaalissa käytössä levymuistiaseman kotelointi estää lasersäteen pääsyn laitteen ulkopuolelle. Laitteen turvallisuusluokka on määritetty standardin EN 60825 mukaisesti.
Safety and Regulatory Information English Translation of Finland Regulatory Information English Translation of Finland Regulatory Information LASER SAFETY SUMMARY LASER SAFETY CLASS 1 LASER PRODUCT (The same in Swedish.) Hewlett-Packard 300mx, 600mx and 700mx jukeboxes are for user safe class 1 laser products. In normal use the enclosure of the optical drives prevents the laser beam from escaping outside of the product.
Safety and Regulatory Information Japanese VCCI Statement Japanese VCCI Statement This equipment is in the Class A category information technology equipment based on the rules of Voluntary Control Council For Interference by Information Technology Equipment (VCCI). When used in a residential area, radio interference may be caused. In this case, user may be required to take appropriate corrective actions.
Glossary C-D cartridge A plastic enclosure that contains an optical disk. The cartridge is labeled "A" or "B" to denote separate sides of the optical disk. The optical disk is never removed from the cartridge. jukebox controller The part of the jukebox that controls the sending and receiving of SCSI commands and controls the disk transport mechanism. LAN Local area network. A group of computers and peripherals physically connected so users can share hardware and software resources. disk See optical disk.
Glossary optical disk A term synonymous with the 5.25-inch magneto-optical disk. There are two types of optical disks used in jukeboxes: rewritable and write-once. inserted, the drive will write data, but will not write over data that has been previously written. This feature is useful for applications that need permanent data security and audit trails. optical disk library See jukebox.
Index A addresses HP Direct, supplies A-3 C changing the administration password 3-14 changing the SCSI IDs 3-17 choosing a location 1-2 configurations listing of 3-20 setting 3-19 connecting power 1-13 connecting the jukebox issues with multiple devices 1-12 only peripheral 1-10 with other devices 1-12 connecting the SCSI cables 1-8 control panel 16-character display 3-5 activity light 3-5 selection buttons 3-5 swivel feature 3-5 customer support A-6 D disk labels jamming shutter 2-4 disks care of 2-6 cho
Index must be one digit apart 3-18 setting LUN mode 3-15 settting 3-15 viewing 3-16 when in LUN mode 3-18 selection buttons CANCEL 3-7 ENTER 3-7 NEXT 3-7 PREV 3-7 using 3-7 setting an operating configuration 319 setting SCSI IDs 3-15 setting the LUN mode 3-15 setting up the jukebox 1-2 shipping the jukebox 1-15 supplies ordering information A-3 supplies and accessories A-3 system components needed 1-3 T tests internal 3-26 troubleshooting 3-33 procedures 3-34 Typographical iii U Use 3-7 using optical disks
