AB291A Fabric Clustering System Support Guide (12-port Switch), April 2004
Table Of Contents
- About This Document
- 1 Introduction to Technology
- 2 Hardware Overview
- 3 Installation Planning
- 4 Installing HP Fabric Clustering System
- 5 Administration and Management
- HP-UX Host Administration and Management
- Switch Administration and Management
- CLI Overview
- Using the CLI
- Advanced Switch Setup
- Configuration, Image, and Log Files
- Configuration, Image, and Log File Overview
- File Management
- Listing Configuration, Image, and Log Files
- Viewing Configuration Files
- Viewing Log Files
- Saving Configuration Files
- Saving for System Reboot
- Saving the Backup Configuration
- Specifying the Configuration to Use at
- Saving and Copying Files
- Downloading Files to the System
- Deleting Configuration, Image, and Log Files
- Managing Log Files
- Understanding the Log Format
- Uploading Log Files
- Administering the System
- 6 Monitoring and Troubleshooting
- A Specifications
- B HP 12-Port 4X Fabric Copper Switch Commands
- Show Commands
- show arp ethernet
- show arp IB
- show authentication
- show backplane
- show boot-config
- show card
- show card-inventory
- show clock
- show config
- show fan
- show host
- show ib
- show ib sm configuration
- show ib sm multicast
- show ib sm neighbor
- show ib sm node subnet-prefix
- show ib sm partition
- show ib sm port
- show ib sm service
- show ib sm switch
- show ib-agent channel-adapter
- show ib-agent summary
- show ib-agent switch
- show ib-agent switch linear-frd-info
- show ib-agent switch all mcast-info lid
- show ib-agent switch all node-info
- show ib-agent switch all pkey-info
- show ib-agent switch port-info
- show ib-agent switch sl-vl-map
- show ib-agent switch switch-info
- show interface ib
- show interface ib sm
- show interface ib sm statistics
- show interface mgmt-ethernet
- show interface mgmt-ib
- show interface mgmt-serial
- show ip
- show location
- show logging
- show ntp
- show power-supply
- show running-status
- show sensor
- show snmp
- show system-services
- show terminal
- show trace
- show user
- show version
- IP Commands
- HP Fabric Clustering System Commands
- Administrative Commands
- action
- boot-config
- broadcast
- card
- clock
- configure
- copy
- delete
- dir
- disable
- enable
- exec
- exit
- ftp-server enable
- gateway
- help
- history
- hostname
- install
- interface
- interface mgmt-ethernet
- interface mgmt-ib
- ip
- location
- login
- logging
- logout
- more
- ntp
- ping
- radius-server
- reload
- shutdown
- snmp-server
- telnet
- terminal length
- terminal time-out
- trace
- type
- username
- who
- write
- Show Commands
- C How to Use Windows HyperTerminal
- Glossary
HP 12-Port 4X Fabric Copper Switch Commands
Show Commands
Appendix B
134
show boot-config
Synopsis:
The show boot-config command lists the image and configuration files that are used to initialize chassis
firmware and configure the interfaces.
Syntax:
show boot-config
Command Modes:
User-execute and privileged-execute modes.
Privilege Level:
General read-only user.
Usage Guidelines:
This command lists the files that were used to bring-up the system, the files to use the next time the system
is rebooted, and the backup files to use in the event that the primary boot files are not available.
The fields in the show boot-config output are described in the table below.
Examples:
HP-IB# show boot-config
============================================================================
System Boot Configuration
============================================================================
slot-id : 1
sw-version : HP-IBOS-1.1.3/build255
Table B-3 show boot-config Command Field Descriptions
Field Description
slot-id Slot identifier of the controller card in use. This value is either 1 or 14.
sw-version Version of the software-image used to initialize chassis components.
last-image-source Directory name of the system-image used to initialize chassis components.
last-config-source Name of the file used to configure chassis interface cards and set system parameters.
primary-image-source Name and directory location of the system-image to use to initialize chassis components the next
time the system reboots.
primary-config-source Name of the configuration file to use to restore the system configuration the next time the system
reboots. This field is affected by the save running-config command.
secondary-image-source Alternate image directory to use to initialize the system. This file is used if the file specified in
primary-image-source is not available.
secondary-config-source Alternate configuration file to use to restore the system configuration. This file is used if the file
specified in primary-config-source is not available.