AB291A Fabric Clustering System Support Guide (12-port Switch), April 2004
Table Of Contents
- About This Document
- 1 Introduction to Technology
- 2 Hardware Overview
- 3 Installation Planning
- 4 Installing HP Fabric Clustering System
- 5 Administration and Management
- HP-UX Host Administration and Management
- Switch Administration and Management
- CLI Overview
- Using the CLI
- Advanced Switch Setup
- Configuration, Image, and Log Files
- Configuration, Image, and Log File Overview
- File Management
- Listing Configuration, Image, and Log Files
- Viewing Configuration Files
- Viewing Log Files
- Saving Configuration Files
- Saving for System Reboot
- Saving the Backup Configuration
- Specifying the Configuration to Use at
- Saving and Copying Files
- Downloading Files to the System
- Deleting Configuration, Image, and Log Files
- Managing Log Files
- Understanding the Log Format
- Uploading Log Files
- Administering the System
- 6 Monitoring and Troubleshooting
- A Specifications
- B HP 12-Port 4X Fabric Copper Switch Commands
- Show Commands
- show arp ethernet
- show arp IB
- show authentication
- show backplane
- show boot-config
- show card
- show card-inventory
- show clock
- show config
- show fan
- show host
- show ib
- show ib sm configuration
- show ib sm multicast
- show ib sm neighbor
- show ib sm node subnet-prefix
- show ib sm partition
- show ib sm port
- show ib sm service
- show ib sm switch
- show ib-agent channel-adapter
- show ib-agent summary
- show ib-agent switch
- show ib-agent switch linear-frd-info
- show ib-agent switch all mcast-info lid
- show ib-agent switch all node-info
- show ib-agent switch all pkey-info
- show ib-agent switch port-info
- show ib-agent switch sl-vl-map
- show ib-agent switch switch-info
- show interface ib
- show interface ib sm
- show interface ib sm statistics
- show interface mgmt-ethernet
- show interface mgmt-ib
- show interface mgmt-serial
- show ip
- show location
- show logging
- show ntp
- show power-supply
- show running-status
- show sensor
- show snmp
- show system-services
- show terminal
- show trace
- show user
- show version
- IP Commands
- HP Fabric Clustering System Commands
- Administrative Commands
- action
- boot-config
- broadcast
- card
- clock
- configure
- copy
- delete
- dir
- disable
- enable
- exec
- exit
- ftp-server enable
- gateway
- help
- history
- hostname
- install
- interface
- interface mgmt-ethernet
- interface mgmt-ib
- ip
- location
- login
- logging
- logout
- more
- ntp
- ping
- radius-server
- reload
- shutdown
- snmp-server
- telnet
- terminal length
- terminal time-out
- trace
- type
- username
- who
- write
- Show Commands
- C How to Use Windows HyperTerminal
- Glossary
Chapter 5
Administration and Management
Switch Administration and Management
74
Step 7.
Reboot the system.
1. Set-Up the Hardware Connection For detailed information about the HP Fabric Clustering System Switch
hardware, refer to “Switch Setup” on page 35.
There are two types of hardware connections that can be used to download a new image to the system.
• Out-of-Band connection
Connect the server to the switch ethernet management port, if a connection does not already exist.
• In-Band connection
Use a 4x copper cable to connect from an HP Fabric Clustering System-enabled host to a Fabric port on the HP Fabric
Clustering System Switch system.
2. Check the Image Version This section describes how to use the Command Line Interface (CLI) to copy the software
that runs the system.
Refer to “Deleting Images Through the CLI” on page 78
Step 1. Enter the privileged-execute mode.
HP-IB> enable
HP-IB#
Step 2. Enter the dir image command.
Note the names of the installed system-images and image files displayed in the file-name column.
If there are already three images installed, there will not enough space for the new image to copy and install.
Delete an existing older image before copying the new image (refer to “Deleting System Images and Image
Files” on page 78).
HP-IB# dir image
================================================================================
Existing Boot-Images on System
================================================================================
slot date-created size file-name
--------------------------------------------------------------------------------
1 Tue Jan 13 10:24:35 2004 18905824 HP-AB291A-Release-1.1.3hp-build023.img
1 Sun Feb 22 10:24:44 2004 18932637 HP-AB291A-Release-1.1.3hp-build025.img
1 Sun Feb 22 10:29:45 2004 13085184 Release-1.1.3hp/build025
HP-IB#
Step 3. Check the installed system-image used to boot the system with the show boot-config command.
HP-IB# show boot-config
===============================================================================
System Boot Configuration
================================================================================
slot-id : 1
sw-version : Release-1.1.3hp/build025
last-image-source : Release-1.1.3hp/build025
primary-image-source : Release-1.1.3hp/build025
HP-IB#