AB378B Fibre Channel Mass Storage Adapter Installation Guide HP-UX and OpenVMS Storage Manufacturing Part Number: AB378-96002 December, 2006 Printed in the US © Copyright 2006 Hewlett Packard Development Company L.P.
Legal Notices The information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents 1. Fibre Channel Adapter Installation for HP-UX Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Important Patches and Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing Driver Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4
1 Fibre Channel Adapter Installation for HP-UX This chapter contains installation prerequisites, guidelines, and procedures for the AB378B host bus adapter.
Fibre Channel Adapter Installation for HP-UX Important Patches and Updates — Fibre Channel driver software media (included with the OS or application CD) — Fibre Channel host bus adapter with an optical port protector attached (not included with all adapters) • Verify that you have the following cabling items: — Fiber optic cable terminated with a duplex LC connector.
Fibre Channel Adapter Installation for HP-UX Installing Adapter Hardware Step 7. Select Mark for Install from the Actions menu. Step 8. Select Install from the Actions menu. Installation begins and the Install Analysis window opens. Step 9. Click OK in the Install Analysis window to confirm that you want to install the software. The Install window opens. View the Install window to read processing data while the software installs. When the Status field indicates Ready, the Confirmation window opens. Step 10.
Fibre Channel Adapter Installation for HP-UX Installing Adapter Hardware Installing the Fibre Channel Adapter CAUTION Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD safety precautions could result in damage to equipment. NOTE The optical port protector is used only to protect the adapter port when it is not in use. Do not use the protector as a diagnostic tool. Install OnlineDiag, which is available at: http://www.software.hp.
Fibre Channel Adapter Installation for HP-UX Attaching the Adapter to Other Fibre Channel Devices Figure 1-1 AB378B Single Port Fibre Channel Adapter and Port WWN Attaching the Adapter to Other Fibre Channel Devices To attach the adapter to other Fibre Channel devices, follow these steps: 1. Remove the Fibre Channel host bus adapter’s optical port protector (if included). 2. Attach a connector cable to the Fibre Channel host bus adapter. a. Align the slotted plug with the keyed connector. b.
Fibre Channel Adapter Installation for HP-UX Verifying the Fibre Channel Adapter Installation Be sure to use LC-LC or LC-SC cables for the Fibre Channel host bus adapters which use the FCD driver.
Fibre Channel Adapter Installation for HP-UX LED Interpretation LED Interpretation Table 1-3 AB378B LED Interpretation Table Yellow LED (4 Gbps) Green LED (2 Gbps) Amber LED (1 Gbps) Power OFF OFF OFF OFF Card doesn’t have power Power ON ON ON ON Card powered on and not initialized Power ON 1 Flash/s 1 Flash/s 1 Flash/s After firmware initialization AWAITING LINK-UP All flashing at the same time Firmware Fault 2 Flash/s 2 Flash/s 2 Flash/s All three LEDs flash in continuous sequence
Fibre Channel Adapter Installation for HP-UX Obtaining Card Information after Installation Hardware Path is = 0/0/6/1/0 Maximum Frame Size = 2048 Driver-Firmware Dump Available = NO Driver-Firmware Dump Timestamp = N/A Driver Version = @(#) libfcd.a HP Fibre Channel ISP 23xx & 24xx Driver B.11.23.06 /ux/core/isu/FCD/kern/src/common/wsio/fcd_init.c:Sep 5 2006,19:57:2 This card is capable of running at higher bus speeds, up to 266Mhz. The speed of the server slot determines the maximum speed.
Fibre Channel Adapter Installation for HP-UX Verifying Connectivity Verifying Connectivity Once your HP Fibre Channel Mass Storage software and hardware is installed and running, follow these steps to verify connectivity: Step 1. Check the state of all Fibre Channel hardware and interfaces. Enter the ioscan command and verify that the Hardware State and the HW-Interface State are CLAIMED. If the Fibre Channel device file has not been created, enter the following commands: # insf -e # ioscan -f Step 2.
Fibre Channel Adapter Installation for HP-UX Interpreting Hardware Paths Table 1-4 describes each field in the hardware path. Table 1-4 Hardware Path Field Descriptions Fibre Channel Topology of HBA Field Value Fabric Topologies Private Loop Adapter The hardware path of the Fibre Channel adapter through which the Logical Unit Number (LUN) is seen. For multiport adapters, this field describes a specific port on the adapter. Domain Dependent on the Fibre Channel topology of the HBA.
Fibre Channel Adapter Installation for HP-UX Interpreting Hardware Paths Table 1-4 Hardware Path Field Descriptions (Continued) Fibre Channel Topology of HBA Field Target Value Depends on the Fibre Channel topology and the LUN addressing method used. Fabric Topologies Private Loop For LUNs with Peripheral Device Addressing, the value of this field is the lower 4-bits of the third byte of the N_Port ID of the target device.
Fibre Channel Adapter Installation for HP-UX Interpreting Hardware Paths 16 Chapter 1
2 Fibre Channel Adapter Installation for OpenVMS This chapter contains installation prerequisites, guidelines, and procedures for the AB378B host bus adapter.
Fibre Channel Adapter Installation for OpenVMS Installing Driver Software Installing Driver Software The driver for the AB378B Fibre Channel Host Bus Adapter is included in the installation of OpenVMS Version 8.3 and later OpenVMS releases. To check for the latest software patches, search for OpenVMS at: http://www.itrc.hp.com. Installing Adapter Hardware The Online Addition and Replacement feature is not supported in OpenVMS.
Fibre Channel Adapter Installation for OpenVMS Installing Adapter Hardware Figure 2-1 AB378B Single Port Fibre Channel Adapter and Port WWN The N_Port Port World Wide Name (WWN) is printed on the bulkhead.
Fibre Channel Adapter Installation for OpenVMS Attaching the Adapter to Other Fibre Channel Devices Attaching the Adapter to Other Fibre Channel Devices To attach the adapter to other Fibre Channel devices, follow these steps: 1. Remove the Fibre Channel host bus adapter’s optical port protector (if included). 2. Attach a connector cable to the Fibre Channel host bus adapter. a. Align the slotted plug with the keyed connector. b. Push the connector in until you hear it click. 3.
Fibre Channel Adapter Installation for OpenVMS Verifying the Fibre Channel Adapter Installation Verifying the Fibre Channel Adapter Installation 1. Boot OpenVMS and log in to a privileged account. 2. Confirm that all of the AB378B Fibre Channel Adapter ports have been configured. A fibre channel port is represented by devices named FGA0:, FGB0:, etc. There is one port per adapter, and there should be one device per port. The device type should be QLogic ISP24xx FibreChannel, as shown below. 3.
Fibre Channel Adapter Installation for OpenVMS Additional Configuration Information SDA> FC SHOW STDT SYS$PGQDRIVER - QLogic ISP24xx - FGA0 - SPDT 8272B100 - STDTs ------------------------------------------------------------| STDT Cred STDT FC-LA Port Name LID PortID | Stat I/Os -------- ----- ------------------- --- ------ + ---- ---82B84BC0 00010 5000.1FE1.5001.A3EC 091 013200 | 0001 0000 82B88E80 00015 5000.1FE1.0015.2D08 097 020800 | 0001 0000 82B7CE00 00006 5000.1FE1.0015.
A Technical Specifications and Regulatory Information AB378B Technical Specifications Performance Characteristics Local bus mode and speed PCI-X 266MHz, PCI-X 133MHz, PCI-X 66MHz, PCI 66MHz, PCI 33MHz Connectivity Single port Fibre Channel, multi-mode short-wave optical link Link Speed 4Gbps / 2Gbps / 1Gbps Link Distance 4Gbps : 150m; 2Gbps : 300m; 1Gbps : 500m Over 50/125um multi-mode fiber optic cable Connector One LC Duplex Connector Bus Slot 3.
Technical Specifications and Regulatory Information FCC Statement (For U.S.A.) FCC Statement (For U.S.A.) Federal Communications Commission Radio Frequency Interference Statement WARNING This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that might cause undesired operation.
Technical Specifications and Regulatory Information VCCI (Japan) (PCI Card Only) VCCI (Japan) (PCI Card Only) This equipment complies with the Class A category for information technology equipment based on the rules of Voluntary Control Council for Interference by Information Technology Equipment. When used in a residential area, radio interference may be caused. In this case, the user may be required to take appropriate corrective actions.
Technical Specifications and Regulatory Information Laser Safety Statements CAUTION The optical transceiver provided on the network interface card contains a laser system and is classified as a “Class 1 Laser Product” per EN 60825-1, Safety of Laser products. Class 1 laser products are considered safe and do not pose a biological hazard if used within the data sheet limits and instructions.
Technical Specifications and Regulatory Information AB378B Declaration of Conformity AB378B Declaration of Conformity Appendix A 27
