FibrChanl-02 (fclp) B.11.31.1003.01 Fibre Channel Mass Storage Driver for HP-UX 11i v3 Release Notes

ManualsBrandsHP ManualsNetwork HardwareHP-UX 11i v3 I/O Cards

FibrChanl-02 (fclp) Fibre Channel Mass

Storage Driver for HP-UX 11i v3 Release

Notes

Version Number B.11.31.1003.01

HP Part Number: 5900-0486

Published: March 2010

Edition: 1.0

Summary of content (13 pages)

PAGE 1
FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 Release Notes Version Number B.11.31.1003.01 HP Part Number: 5900-0486 Published: March 2010 Edition: 1.
PAGE 2
PAGE 3
Table of Contents FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview...........................5 New and changed features in this release..............................................................................................5 New features.....................................................................................................................................5 Known problems fixed in this version...................................................................
PAGE 4
List of Tables 1 2 3 4 5 6 7 8 4 HP-UX March 2010 (AR1003) Fixes................................................................................................5 HP-UX November 2009 Fixes..........................................................................................................5 HP-UX September 2009 Fixes..........................................................................................................5 HP-UX June 2009 Fixes............................................................
PAGE 5
This document provides information about the B.11.31.1003.01 release of the FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3. FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview This release of the FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 (version B.11.31.1003.01) documents defect fixes and version changes. New and changed features in this release New features The following feature is new with the B.11.31.1003.
PAGE 6
Table 6 HP-UX December 2008 Fixes Defect ID Description QXCR1000867632 The fix delivers the SNIA API HBA_GetFcpTargetMappingV2(), which is used to oormation about the targets mapped through a port on a multiport Fibre Channel card.btain inf QXCR1000841117 vPars boot panic with AD222 HBA has been fixed. QXCR1000869847 System panic due to spinlock being held too long in a tracing loop has been fixed.
PAGE 7
Using EFI boot partition (no HPUX partition on boot media) (C) Copyright 1999-2006 Hewlett-Packard Development Company, L.P. All rights reserved HP-UX Boot Loader for IPF -- Revision 2.029 Press Any Key to interrupt Autoboot \EFI\HPUX\AUTO ==> boot vmunix Seconds left till autoboot 0 AUTOBOOTING...Could not open file vmunix to check for a directory Could not open vmunix loading failed HPUX> This issue is addressed in system firmware version 3.01 for rx2660, rx3600, and rx6600.
PAGE 8
• Host bus adapters using the fclp HP-UX driver stay in AWAITING LINK UP state when connected to a DS2500 device The solution to this issue is to set the speed of the adapter port to 2 Gb, by using the drvcfg -s command at the EFI shell prompt, to configure the port speed: 1. 2. 3. 4. 5. 6. 7. 8. 9. • To view the Emulex driver handle information, type Shell> drivers at the EFI shell prompt - - a list of drivers is displayed. Write down the driver handle associated with the Emulex SCSI Pass Thru Driver.
PAGE 9
NOTE: The FC-COMMON.FC-SNIA fileset is part of the CommonIO bundle. If FC-COMMON.FC-SNIA (1003 or later) is not present on a system, swinstall of the FC-FCLP product will display errors. If you ignore the errors and proceed with the swinstall, the FC-FCLP.FC-FCLP-RUN fileset will not be installed. The following patch is required only if your system is missing the March 2008 HP-UX 11.
PAGE 10
• • • • • • AD355A PCIe Dual Port 4Gb Fibre Channel Adapter AD299A PCIe Single Port 4Gb Fibre Channel Adapter AD221A HP PCIe Single Port 4Gb Fibre Channel and Single Port 1000 BT Adapter AD222A HP PCIe Dual Port 4Gb Fibre Channel and Dual Port 1000BT Adapter AD393A HP PCIe Dual Port 4Gb Fibre Channel and Dual Port 1000SX Adapter 403621-B21 Emulex LPe1105–HP 4Gb Fibre Channel Adapter for HP c-Class BladeSystem NOTE: Please note the following slot limitations on rx3600 and rx6600 servers: • Slots 5 and 6 ar
PAGE 11
On HP-UX, the fcmsutil /dev/fclpX vpd command displays the VPD: # fcmsutil /dev/fclp5 vpd V I T A L --------- P R O D U C T ------------- D A T A ------- Product Description : "HP BLc Emulex LPe1105-HP FC Mezz Option Kit" Part number : "404987-001" Part Serial number : "MY18071ZYV" Engineering Date Code : "B-4813" Mfd. Date : "4807" Misc. Information : "PW=6.5W; PCIe x4 Gen1" ROM Firmware version : "2.72A2 SLI-3 (Z3F2.72A2)" EFI version : "ZU6.
PAGE 12
Card revision Although EDC is the primary way to identify changes in recipe for Integrity systems, it is also possible to use the card “Rev”, which is printed on a label on the box containing the card, and on a label on the card. CAUTION: There are at least three different “Rev” identifiers on the card. The correct one to use is printed on the SKU label — Integrity-supported versions have a “REV” of 0C or later.
PAGE 13
• • Support Matrix: includes a matrix of Fibre Channel adapters, supported hardware platforms, operating systems, driver bundle versions, and minimum PDC/firmware requirements. White Paper: white papers can also be found in this section. Software availability in native languages This product is available only in the English language.