FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 Release Notes Version Number B.11.31.1109.01 HP Part Number: 5900-2046 Published: November 2011 Edition: 1.
Contents FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview.............................3 New and changed features in this release...................................................................................3 New features......................................................................................................................3 Known problems fixed in this version...........................................................................................
This document provides information about the B.11.31.1109.01 release of the FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3. FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview This release of the document for the FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 (version B.11.31.1109.01) documents defect fixes and version changes. New and changed features in this release New features This feature is new with the B.11.31.1109.
Table 3 HP-UX April 2011 (WEB1104) Fixes Defect ID Description QXCR1001118460 SNIA library has been modified to not to use invalid target entries that caused core dumps. Table 4 HP-UX March 2011 (AR1103) Fixes Defect ID Description QXCR1001065388 SNIA: Model for AH402A/AH403A is displayed as AD222A in SMH. QXCR1001065578 SNIA: SMH displays 4G speed for 8G Emulex HBAs (AH402A/AH403A). QXCR1001020559 SNIA: FC Instance Enumeration FCPortControllerCollection fails if port disabled.
Table 7 HP-UX March 2010 (AR1003) Fixes Defect ID QXCR1000931979 Description This fixes the issue where snia_demo ouputs an error message: /dev/fclp* not found, when run on a system with the fclp driver installed and no fclp adapters connected. QXCR1000969594 This fixes the issue where SNIA: HBA_OpenAdapter API fails with the HBA_STATUS_ERROR. QXCR1000976833 This fixes the issue where SNIA does not report more than 500 luns per HBA.
Known problems and limitations This section provides a list of known problems and limitations as known to HP at time of publication. If workarounds are available, they are included. • After a host system is booted, if a private loop configuration is connected, the target is not detected Corrective action: Execute a probing ioscan to discover the new target. To run a probing scan, run ioscan without the -k option.
HPUX> This issue is addressed in system firmware version 3.01 for rx2660, rx3600, and rx6600. There are three workarounds for this issue: 1. Return to the Boot Manager, enter and exit the EFI shell a second time, and retry the boot; or, 2. Reset the system and retry the boot; or, 3. Configure the EFI driver to always map the boot devices using the drvcfg -s at the EFI shell prompt.
5. 6. 7. 8. 9. • Select (highlight) the Setup Utility option and press Enter. Select (highlight) the Configure HBA Parameters option and press Enter. Select (highlight) the Force Link Speed option and press Enter. Select (highlight) the 2Gb/s link speed option from the list presented, and press Enter. After completing your selection, use the ESC key to exit the EFI configuration menus.
Table 14 Recommended firmware/EFI versions (November 2011) Fibre Channel Adapter EFI Driver Version Firmware Version Universal Boot Code AH403A 4.00a8 or later 2.00a4 or later 5.03a10 AH402A 4.00a8 or later 2.00a4 or later 5.03a10 456972-B21 4.00a8 or later 2.00a4 or later 6.03a11 AD355A, AD299A 4.00a8 or later 2.82x4 or later 5.03a10 AD221A, AD222A, AD393A 4.00a8 or later 2.82x4 or later 5.03a10 403621-B21 4.00a8 or later 2.82x4 or later 6.03a11 AT094A 4.00a8 or later 2.
Hardware Requirements This version of the FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 runs on HP Integrity servers with the HP-UX 11i v3 (11.31) operating system.
On HP-UX, the fcmsutil /dev/fclpX vpd command displays the VPD: # fcmsutil /dev/fclp5 vpd V I T A L --------- P R O D U C T ------------- D A T A ------- Product Description : "HP BLc Emulex LPe1105-HP FC Mezz Option Kit" Part number : "404987-001" Part Serial number : "MY18071ZYV" Engineering Date Code : "B-4813" Mfd. Date : "4807" Misc. Information : "PW=6.5W; PCIe x4 Gen1" ROM Firmware version : "2.72A2 SLI-3 (Z3F2.72A2)" EFI version : "ZU6.
Card revision Although EDC is the primary way to identify changes in recipe for Integrity systems, it is also possible to use the card “Rev”, which is printed on a label on the box containing the card, and on a label on the card. CAUTION: There are at least three different “Rev” identifiers on the card. The correct one to use is printed on the SKU label — Integrity-supported versions have a “REV” of 0C or later. Firmware and EFI HP Integrity blades require this minimum firmware and EFI: • Firmware: 2.
• Support Matrix: includes a matrix of Fibre Channel adapters, supported hardware platforms, operating systems, driver bundle versions, and minimum PDC/firmware requirements. • White Paper: white papers can also be found in this section. Software availability in native languages This product is available only in the English language.
