FibrChanl-03 (fcoc) B.11.31.1109.01 Fibre Channel Mass Storage Driver for HP-UX 11i v3 Release Notes

ManualsBrandsHP ManualsNetwork HardwareHP-UX 11i v3 I/O Cards

FibrChanl-03 (fcoc) Fibre Channel Mass

Storage Driver for HP-UX 11i v3 Release

Notes

Version Number B.11.31.1109.01

HP Part Number: 5900-1861

Published: September 2011

Edition: 1.1

Summary of content (7 pages)

PAGE 1
FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 Release Notes Version Number B.11.31.1109.01 HP Part Number: 5900-1861 Published: September 2011 Edition: 1.
PAGE 2
Contents FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview............................3 New and changed features in this release...................................................................................3 New features......................................................................................................................3 Known problems fixed in this version...........................................................................................
PAGE 3
This document provides information about the B.11.31.1109.01 release of the FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3. FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview This release of the document for the FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 (version B.11.31.1109.01) documents defect fixes and version changes. New and changed features in this release New features This feature is new with the B.11.31.1109.
PAGE 4
Table 4 HP-UX November 2010 (WEB1011) Fixes Defect ID N/A Description There are no known problems fixed in this version. NOTE: 11i v3. WEB1011 is the initial controlled availability release of FibrChanl-03 (fcoc) on HP-UX Known problems and limitations This section provides a list of known problems and limitations as known to HP at time of publication. If workarounds are available, they are included. • Up to eight NC551m HBAs are supported in a BL890c i2 system.
PAGE 5
2. 3. Select Emulex Configuration Utility Ver:X.XXXXX and press Enter. When the Emulex Configuration Utility screen is displayed with Emulex Configuration Setup Utility selected, press Enter. 4. A list of all the adapters in the system is displayed. Your list may vary depending on the installed adapters. Locate the adapter you want to configure. Use the up/down arrows on your keyboard to select it, and press Enter.
PAGE 6
5. The Emulex Adapter Configuration Main Menu screen comes up. Select Set Boot From SAN. A Disable Enable menu is displayed. Use the arrow keys to select the Enable option and press Enter. The selection is updated to NVRAM and the current setting is displayed. 6. On the same Emulex Adapter Configuration Main Menu screen, select Back to Display Adapters and RECONNECT DEVICES and press Enter. Type s to save the changes. Exit the Emulex utility. Control B to go into cm and type rs to reset the system. 7.
PAGE 7
• VCSU FW 1.6.0 or higher • VC-Enet FW Version 3.15 or higher (for profile migration, 3.17 or higher is required) • NC551m Firmware version 2.702.517.703 or higher • HP-UX 11i v3 OS Fusion version B.11.31.1103 or higher • HP-UX CommonIO 11.31.1103 (B.11.31.1103) or higher NOTE: The FC-COMMON.FC-SNIA fileset is part of the CommonIO bundle. If FC-COMMON.FC-SNIA (1103 or later) is not present on a system, swinstall of the FC-FCOC product will display errors.