HP-UX vPars and Integrity VM V6.3 Administrator Guide

# olrad -f -r 10-0-1-0-2-3
Activity: Start of Prepare Replace
Target slot: 10-0-1-0-2-3
Critical Resource Analysis(CRA) in progress...
[NOTE: The CRA may take a few minutes to complete on large
configurations. It is recommended not to disrupt this operation.]
CRA REPORT SUMMARY: CRA detected DATA CRITICAL usages.
Detailed CRA report is available in /var/adm/cra.log file.
CRA Error : resources associated with possible data loss
Target slot : 10-0-1-0-2-3
Activity : CRA being forced using -f option
Target slot : 10-0-1-0-2-3
Activity : End of Prepare Replace
Target slot : 10-0-1-0-2-3
Activity : Target slot powered off, drivers suspended, OK to replace the card
Target slot : 10-0-1-0-2-3
To verify that the DLA NIC is successfully suspended, you can use the following options of the
olrad(1M) command and ioscan(1M) command.
# olrad –q
Slot Path Link Max Max Link Pwr Occu Susp OLAR OLD Mode
Spd Link Link Width
Spd Width
10-0-1-0-2-3 42/0/0/2/0/0 5.0 5.0 x8 x8 On Yes Yes Yes Yes PCIe
# ioscan -kfnC hpvmdio
Class I H/W Path Driver S/W State H/W Type Description
======= == ============== ======= ========== ========= ========================
hpvmdio 0 42/0/0/2/0/0/0 hpvmdio SUSPENDED INTERFACE HP AM225-60001 PCIe 2-p 10GbE-SFP+ Adapter
/dev/hpvmdio0
hpvmdio 1 42/0/0/2/0/0/1 hpvmdio SUSPENDED INTERFACE HP AM225-60001 PCIe 2-p 10GbE-SFP+ Adapter
/dev/hpvmdio1
Further, ioscan output inside the guest will also show the DLA NIC port in SUSPENDED state.
# ioscan -kfnC lan
Class I H/W Path Driver S/W State H/W Type Description
===== === ======== ======= ========= ========= ==========================================
lan 8 0/1/5/0 iexgbe SUSPENDED INTERFACE HP AM225-60001 PCIe 2-p 10GbE-SFP+ Adapter
lan 17 0/2/2/0 iexgbe SUSPENDED INTERFACE HP AM225-60001 PCIe 2-p 10GbE-SFP+ Adapter
After the DLA NIC is replaced with a new one, you can use the Post Replace option of the
olrad(1M) command (olrad –R) to resume usage of the card. The following is the sample
output of the olrad -R command.
# olrad -R 10-0-1-0-2-3
Activity: Start of Post Replace
Target slot: 10-0-1-0-2-3
Activity: End of Post Replace
Target slot: 10-0-1-0-2-3
Activity: Target slot powered on, drivers resumed, OK to start using the card
Target slot: 10-0-1-0-2-3
To verify that the DLA NIC is successfully resumed, you can use the following options of the
olrad(1M) command and ioscan(1M) command.
# olrad -q
Slot Path Link Max Max Link Pwr Occu Susp OLAR OLD Mode
Spd Link Link Width
Spd Width
10-0-1-0-2-3 42/0/0/2/0/0 5.0 5.0 x8 x8 On Yes No Yes Yes PCIe
178 PCI OLR support on VSPs