HP Virtual Connect Flex-10 & FlexFabric Cisco Nexus 5000 & 2000 series Integration

15
(*) - local vPC is down, forwarding via vPC peer-link
vPC domain id : 1000
Peer status :peer adjacency formed ok
vPC keep-alive status : peer is alive
Configuration consistency status : success
vPC role : secondary
Number of vPCs configured : 0
Peer Gateway :Disabled
Dual-active excluded VLANs : -
vPC Peer-link status
--------------------------------------------------------------------------------------------
id Port Status Active vlans
-- ---- ------ -----------------------------------------------------------------------------
1 Po1000 up -
Step 4. Configuring vPC EtherChannel Host Interface
! Create Po11 and add it to vPC 11 on Nexus 5020-1 and Nexus 5020-2
Nexus-5020-1(config)# interface port-channel11
Nexus-5020-1(config-if)# description Connection to Enc1-Flex10-Bay1
Nexus-5020-1(config-if)# switchport mode trunk
Nexus-5020-1(config-if)# switchport trunk allowed vlan 101-109
 Create EtherChannel 11
Nexus-5020-1(config-if)# spanning-tree port type edge trunk
 Consider the interface as edge port
Nexus-5020-1(config-if)# vpc 11
 Create vPC 11
Nexus-5020-1(config-if)# interface Ethernet100/1/1

A
dd Eth100/1/1 interface to Po11
Nexus-5020-1(config-if)# description Connection to Enc1-Flex10-Bay1
Nexus-5020-1(config-if)# lacp rate fast
 Enable LACP Fast Timeout
Nexus-5020-1(config-if)# switchport mode trunk
Nexus-5020-1(config-if)# switchport trunk allowed vlan 101-109
Nexus-5020-1(config-if)# spanning-tree port type edge trunk
Nexus-5020-1(config-if)# channel-group 11 mode active
Nexus-5020-2(config)# interface port-channel11
Nexus-5020-2(config-if)# description Connection to Enc1-Flex10-Bay1
Nexus-5020-2(config-if)# switchport mode trunk
Nexus-5020-2(config-if)# switchport trunk allowed vlan 101-109
Nexus-5020-2(config-if)# spanning-tree port type edge trunk
Nexus-5020-2(config-if)# vpc 11
Nexus-5020-2(config-if)# interface Ethernet101/1/1
Nexus-5020-2(config-if)# description Connection to Enc1-Flex10-Bay1
Nexus-5020-2(config-if)# lacp rate fast
Nexus-5020-2(config-if)# switchport mode trunk
Nexus-5020-2(config-if)# switchport trunk allowed vlan 101-109
Nexus-5020-2(config-if)# spanning-tree port type edge trunk
Nexus-5020-2(config-if)# channel-group 11 mode active
 Configure Nexus 5020-2
! Create Po12 and add it to vPC 12 on Nexus 5020-1 and Nexus 5020-2
Nexus-5020-1(config)# interface port-channel12
Nexus-5020-1(config-if)# description Connection to Enc1-Flex10-Bay2
Nexus-5020-1(config-if)# switchport mode trunk
Nexus-5020-1(config-if)# switchport trunk allowed vlan 101-109
 Create EtherChannel 12
Nexus-5020-1(config-if)# spanning-tree port type edge trunk
 Consider the interface as edge Port
Nexus-5020-1(config-if)# vpc 12
 Create vPC 12
Nexus-5020-1(config-if)# interface Ethernet100/1/2
Nexus-5020-1(config-if)# description Connection to Enc1-Flex10-Bay2

A
dd Eth100/1/2 interface to Po12
Nexus-5020-1(config-if)# lacp rate fast
 Enable LACP Fast Timeout
Nexus-5020-1(config-if)# switchport mode trunk
Nexus-5020-1(config-if)# switchport trunk allowed vlan 101-109
Nexus-5020-1(config-if)# spanning-tree port type edge trunk
Nexus-5020-1(config-if)# channel-group 12 mode active