HP Z Workstations - 22-in-1 Media Card Reader Installation

ManualsBrandsHP ManualsDesktopHP Z800 Workstation

HP 22-in-1 Media Card Reader

Introduction

This document describes how to install the HP 22-in-1 Media Card Reader into an HP Workstations

adapter bracket, and then install the media card reader and bracket into an HP computer. Basic

troubleshooting information for the HP 22-in-1 Media Card Reader is also included.

Kit contents

●

3.5-inch media card reader with integrated USB cable

●

HP Workstations adapter for 5.25-inch drive bays

● Four M3 guide screws

●

Documentation CD

●

Warranty information

Microsoft, Windows, and Windows Vista are either trademarks or registered

trademarks of Microsoft Corporation in the United States and/or other countries.

ENWW Introduction 1

Summary of content (8 pages)

PAGE 1
HP 22-in-1 Media Card Reader Introduction This document describes how to install the HP 22-in-1 Media Card Reader into an HP Workstations adapter bracket, and then install the media card reader and bracket into an HP computer. Basic troubleshooting information for the HP 22-in-1 Media Card Reader is also included. Kit contents ● 3.5-inch media card reader with integrated USB cable ● HP Workstations adapter for 5.
PAGE 2
Warnings and cautions WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, enable the surface to cool before touching. WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard.
PAGE 3
Installing the media card reader Installing the 5.25-inch bay adapter To install the 3.5-inch media card reader into a 5.25-inch drive bay, you must first install the reader into the 5.25-inch bay adapter. 1. If installing the media reader in an HP Z200 or Z400 Workstation, install four black M3 guide screws in the four lower holes of the bay adapter. Figure 1 Installing the guide screws in the bay adapter for HP Z200 and Z400 Workstations 2. To install the media reader in the 5.
PAGE 4
f. The green carrier latch (5) snaps into place when fully seated. Figure 3 Installing the media reader in the bay adapter Preparing the computer NOTE: Computer models vary. All illustrations are examples only. Accessing the internal components of the computer 1. If you need help preparing the computer for this installation, consult the removal and replacement procedures in the service guide for your computer at http://www.hp.com/support/ manuals. 2.
PAGE 5
Installing the media card reader in the computer 1. Install the media card reader into an optical drive bay. 2. Ensure that the adapter snaps securely into place. Figure 4 Installing the media card reader in the optical bay Connecting the media card reader NOTE: See the service label on the side access panel to locate connectors on the system board. 1. Connect the USB cable from the media card reader directly to a keyed, two-row, 9-pin USB connector on the system board. 2.
PAGE 6
Reassembling the computer To reassemble the computer after installation: 1. Reinstall the card support, if removed. 2. Reinstall the airflow guide, if removed. 3. Reinstall the side access panel. 4. Reconnect power to the computer and all external devices. 5. Restore power to the computer and all external devices.
PAGE 7
Slot ID Media ● CompactFlash Card Type I ● CompactFlash Card Type II ● MicroDrive ● Memory Stick (MS) ● MagicGate Memory Stick (MG) ● MagicGate Memory Stick Duo ● Memory Stick Select ● Memory Stick Duo (MS Duo) ● Memory Stick PRO (MS PRO) ● Memory Stick PRO Duo (MS PRO Duo) ● Memory Stick PRO-HG Duo ● Memory Stick Micro (M2) (adapter required) Compatible media cards For a list of supported USB media cards for the HP 22-in-1 (USB) Media Card Reader, see the “Compatible Media Cards” d
PAGE 8
Table 1 Solving Common Problems (continued) Problem Possible Cause Solution Media card reader cannot write to the media card. The media card is a read-only memory (ROM) card. Check the manufacturer’s documentation included with your card to see if it writable. See the “Compatible Media Cards” document available on the CD included with your reader. Media card reader cannot access data on the media card after inserting it into a slot.