HP Retail Integrated Barcode Scanner Programming Reference Guide
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Table of Contents INTRODUCTION ................................................................................................................................................................................ 1 About this Manual .......................................................................................................................................................................................... 1 Overview ......................................................................................
Contents Label ID Control ...............................................................................................................................................................................................................34 Label ID Symbology Selection − 1D Symbologies ..............................................................................................................................................35 Label ID Symbology Selection − 2D Symbologies .......................................
Contents EAN 8 Check Character Transmission ......................................................................................................................................................................69 Expand EAN 8 to EAN 13 ..............................................................................................................................................................................................70 EAN 8 2D Component ................................................................
Contents Standard 2 of 5 Set Length 1 ................................................................................................................................................................................... 106 Standard 2 of 5 Set Length 2 ................................................................................................................................................................................... 107 INDUSTRIAL 2 OF 5 ...........................................................
Contents MSI Length Control ..................................................................................................................................................................................................... 140 MSI Set Length 1 .......................................................................................................................................................................................................... 141 MSI Set Length 2 .........................................
Contents Postnet BB Control ............................................................................................................................................................................................................................ 177 REFERENCES................................................................................................................................................................................. 179 USB-COM Parameters ...............................................
Chapter 1 Introduction About this Manual This Programming Reference Guide (PRG) is provided for users seeking advanced technical information, including connection, programming, maintenance and specifications. The HP Retail Integrated Barcode Scanner User Guide and other publications associated with this product are downloadable free of charge from the HP website. Overview Chapter 1, (this chapter) presents information about manual conventions, and an overview of the scanner, its features and operation.
Introduction References Manual Conventions The following conventions are used in this document: The symbols listed below are used in this manual to notify the reader of key issues or procedures that must be observed when using the scanner: Notes contain information necessary for properly diagnosing, repairing and operating the scanner. The CAUTION symbol advises you of actions that could damage equipment or property.
About the Scanner Introduction About the Scanner Typically, units are factory-programmed for the most common terminal and communications settings. If you need to modify any programmable settings, custom configuration can be accomplished by scanning the programming barcodes within this guide. The HP barcode scanner is covered in this manual. Programming can alternatively be performed using the Configuration application that can be installed from the CD included with the scanner.
Introduction Programming the Scanner running on a PC. These commands are sent to the scanner over the USB host interface, or they can be printed as barcodes to be scanned. The utility also provides the ability to perform a software upgrade for the connected device.
Chapter 2 Setup Unpacking Check carefully to ensure the scanner and any accessories ordered are present and undamaged. If any damage occurred during shipment, contact HP Technical Support. Information is shown on page 2. KEEP THE PACKAGING. Should the unit ever require service, it should be returned in its original shipping container. Setting Up the Scanner Follow the steps provided in this section to connect and get the scanner up and communicating with its host. 1.
Setup Interface Selection Interface Selection Upon completing the physical connection between the scanner and its host, proceed to Table 1 below if you wish to change the default USB interface type for your application. Scan the appropriate barcode in that section to configure your system’s interface type. The scanner supports the USB host interface, with the following types available: Keyboard (default), Alternate Keyboard, and COM.
Customizing Configuration Settings Setup Customizing Configuration Settings Configure Interface Settings If after scanning the interface barcode from the previous table your installation requires you to select options to further customize the scanner, turn to the appropriate section for your interface type in "Configuration Parameters" starting on page 9.
Setup Customizing Configuration Settings Resetting the Product Configuration to Defaults Restore Custom Defaults If you aren’t sure what programming options are in the scanner, or you’ve changed some options and want to restore the Custom Default Configuration that may have been saved in the scanner, scan the Restore Custom Default Configuration barcode below. This will restore the custom configuration for the currently active interface. Custom defaults are based on the interface type.
Chapter 3 Configuration Using Barcodes This and following sections provide programming barcodes to configure the scanner by changing the default settings. For details about additional methods of programming, see "Configuration Methods" on page 3. You must first enable the scanner to read barcodes in order to use this section. If you have not done this, go to "Setup" starting on page 5 and complete the appropriate procedure.
Enter/Exit Programming Mode You must first enable the scanner to read barcodes in order to use this section. If you have not done this, go to "Setup" starting on page 5 and complete the appropriate procedure. To program features: 1. Scan the ENTER/EXIT PROGRAMMING barcode, available at the top of each programming page, when applicable. 2. Scan the barcode to set the desired programming feature.
Enter/Exit Programming Mode GLOBAL INTERFACE FEATURES The following interface features are configurable by all interface types. Host Commands — Obey/Ignore This option specifies whether the scanner will obey or ignore host commands. When set to ignore, the scanner will ignore all host commands except for those necessary for: • service mode • flash programming mode • keeping the interface active • transmission of labels.
Enter/Exit Programming Mode NOTES 12 HP Retail Integrated Barcode Scanner
USB-COM INTERFACES INTERCHARACTER DELAY on page 14 BEEP ON ASCII BEL on page 15 BEEP UPON NOT ON FILE on page 15 ACK NAK OPTIONS on page 16 ACK CHARACTER on page 17 NAK CHARACTER on page 17 ACK NAK TIMEOUT VALUE on page 18 ACK NAK RETRY COUNT on page 18 ACK NAK ERROR HANDLING on page 19 INDICATE TRANSMISSION FAILURE on page 19 DISABLE CHARACTER on page 20 ENABLE CHARACTER on page 20 The programming barcodes in this chapter allow modifications to the standard USB-COM interface.
Enter/Exit Programming Mode USB-COM Interfaces Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. See page 180 for more information.
USB-COM Interfaces Enter/Exit Programming Mode Beep On ASCII BEL When this parameter is enabled, the scanner issues a beep when a character is detected on the serial line. is issued to gain a user's attention to an illegal entry or other important event.
Enter/Exit Programming Mode USB-COM Interfaces ACK NAK Options This enables/disables the ability of the scanner to support the ACK/NAK protocol. See page 181 for more information.
USB-COM Interfaces Enter/Exit Programming Mode ACK Character This setting specifies an ASCII character or hex value to be used as the ACK character. ASCII characters or any hex value from 0 to 0xFF can be selected. See page 181 for more information. $CR2AC Select ACK Character Setting DEFAULT 0x06 ‘ACK’ Character NAK Character This setting specifies an ASCII character or hex value to be used as the NAK character. ASCII characters or any hex value from 0 to 0xFF can be selected.
Enter/Exit Programming Mode USB-COM Interfaces ACK NAK Timeout Value This option specifies the amount of time the scanner waits for an ACK character from the host following label transmission. The selectable timeout range is 200 milliseconds to 15,000ms (15 seconds) in 200ms increments. A selection of 0 disables the timeout. See page 183 for more information on setting this feature.
USB-COM Interfaces Enter/Exit Programming Mode ACK NAK Error Handling This feature specifies the method the scanner uses to handle receive errors detected while waiting for an ACK character from the host.
Enter/Exit Programming Mode USB-COM Interfaces Disable Character Specifies the value within the host command used to disable the scanner. ASCII characters or any hex value from 0 to 0xFF can be selected. See page 185 for more information on setting this feature. $CR2DC Select Disable Character Setting DEFAULT 0x44 = Disable Character is ‘D’ Enable Character Specifies the value within the host command used to enable the scanner. ASCII characters or any hex value from 0 to 0xFF can be selected.
USB KEYBOARD SETTINGS COUNTRY MODE on page 22 SEND CONTROL CHARACTERS on page 25 INTERCODE DELAY on page 26 CAPS LOCK STATE on page 26 USB KEYBOARD SPEED on page 27 USB KEYBOARD NUMERIC KEYPAD on page 28 Use the programming barcodes in this chapter to select options for USB Keyboard Interface. Reference Appendix B, Standard Defaults for a listing of standard factory settings. Information about control character emulation which applies to keyboard interfaces is listed in Appendix E, Scancode Tables.
Enter/Exit Programming Mode USB Keyboard Settings Country Mode This feature specifies the country/language supported by the USB keyboard. $CKBCO00(CR) DEFAULT Country Mode = U.S. $CKBCO01(CR) Country Mode = Belgium $CKBCO02(CR) Country Mode = Britain $CKBCO11(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Croatia $CKBCO0E(CR) Supports only the interfaces listed in the Country Mode feature description.
USB Keyboard Settings Enter/Exit Programming Mode Country Mode (continued) Supports only the interfaces listed in the Country Mode feature description. $CKBCO13(CR) Country Mode = French Canadian $CKBCO05(CR) Country Mode = Germany $CKBCO0D(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Hungary $CKBCO06(CR) Country Mode = Italy $CKBCO0C(CR) Supports only the interfaces listed in the Country Mode feature description.
Enter/Exit Programming Mode USB Keyboard Settings Country Mode (continued) $CKBCO12(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Poland Supports only the interfaces listed in the Country Mode feature description. $CKBCO08(CR) Country Mode = Portugal $CKBCO10(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Romania Supports only the interfaces listed in the Country Mode feature description.
USB Keyboard Settings Enter/Exit Programming Mode Send Control Characters This feature specifies how the scanner transmits ASCII control characters to the host. Reference Appendix E, Scancode Tables for more information about control characters. Options are as follows: Control Character 00 : Characters from 00 to 0x1F are sent as control character Ctrl+Keys, special keys are located from 0x80 to 0xA1.
Enter/Exit Programming Mode USB Keyboard Settings Intercode Delay Specifies the delay between labels transmitted to the host for this interface. The selectable range for this feature is from 0 to 99 seconds. See page 187 in “References” for detailed information and examples for setting this feature. $CKBID Set Intercode Delay Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
USB Keyboard Settings Enter/Exit Programming Mode USB Keyboard Speed This option specifies the USB poll rate for a USB keyboard. This feature applies ONLY to the USB Keyboard interface.
Enter/Exit Programming Mode USB Keyboard Settings USB Keyboard Speed (continued) $CKBSP07(CR) USB Keyboard Speed = 7ms $CKBSP08(CR) USB Keyboard Speed = 8ms $CKBSP09(CR) USB Keyboard Speed = 9ms $CKBSP0A(CR) USB Keyboard Speed = 10ms USB Keyboard Numeric Keypad This option Controls whether numeric characters will be sent using standard keys or the numeric keypad.
DATA FORMAT GLOBAL PREFIX/SUFFIX starting on page 30 GLOBAL AIM ID starting on page 30 SET AIM ID INDIVIDUALLY FOR GS1-128 starting on page 33 LABEL ID starting on page 34 •Individually Set Label ID •Label ID Control •Label ID Symbology Selection − •Label ID Symbology Selection − 1D Symbologies 2D Symbologies CASE CONVERSION starting on page 40 CHARACTER CONVERSION starting on page 40 The features in this chapter can be used to build specific user-defined data into a message string.
Enter/Exit Programming Mode Data Format Global Prefix/Suffix This option sets up to 20 characters each from the set of ASCII characters or any hex value from 00 to FF. The characters may be added as a prefix (in a position before the barcode data, also called a header) and/or as a suffix (in a position following the barcode data, also called a footer). See page 190 for more detailed instructions on setting this feature.
Data Format Enter/Exit Programming Mode • • A code character (see some samples in the table below), followed by... A modifier character (the modifier character is symbol dependent). $CAIEN00(CR) DEFAULT Global AIM ID = Disable $CAIEN01(CR) Global AIM ID = Enable Table 2.
Enter/Exit Programming Mode FOLLET 2OF5 I2OF5 IATA INDUSTRIAL 2OF5 INDUSTRIAL 2OF5 ISBN ISBT128 CONCAT ISSN MAXICODE MICRO QR MICRO PDF MSI PDF417 PLESSEY POSTAL AUSTRALIAN POSTAL IMB POSTAL JAPANESE POSTAL KIX POSTAL PLANET POSTAL PORTUGAL POSTAL POSTNET BB POSTAL ROYAL MAIL POSTAL SWEDISH POSTNET QR CODE S25 TRIOPTIC UPCA UPCA P2 UPCA P5 UPCA COMPOSITE UPCE UPCE P2 UPCE P5 UPCE COMPOSITE Data Format X I X X Xb X X U Q L M L P X X X X X X X X X X Q S X Ea E E E E E E E 58 49 58 58 58 58 58 55 51 4C 4D 4C
Data Format Enter/Exit Programming Mode Set AIM ID Individually for GS1-128 This feature configures a Label ID individually for the GS1-128 symbology and the programming for this works the same way as Label ID. See "Label ID: Set Individually Per Symbology" starting on page 195 for detailed instructions on setting this feature.
Enter/Exit Programming Mode Data Format Label ID A Label ID is a customizable code of up to three ASCII characters (each can be one of hex 0x01-0xFF), used to identify a barcode symbology type. It can be appended previous to or following the transmitted barcode data, depending upon how this option is enabled. This feature provides options for configuring custom Label IDs or individually per symbology (see “Individually Set Label ID” below).
Data Format Enter/Exit Programming Mode Label ID Symbology Selection − 1D Symbologies This option selects the symbology for which a Label ID is to be configured. See "Label ID" on page 34 or page "Label ID: Set Individually Per Symbology" on page 195 for more detailed instructions. If less than the expected string of 3 characters are selected, scan the ENTER/ EXIT barcode twice to accept the selection and exit Programming Mode.
Enter/Exit Programming Mode Data Format Label ID Symbology Selection − 1D Symbologies (continued) $C8BID Set EAN 8 Label ID Character(s) $C8MID Set EAN 8 Composite Label ID Character(s) $C82ID Set EAN 8 P2 Label ID Character(s) $C85ID Set EAN 8 P5 Label ID Character(s) $C4BID Set GS1 DataBar 14 Label ID Character(s) $C4CID Set GS1 DataBar 14 Composite Label ID Character(s) $CXBID Set GS1 DataBar Expanded Label ID Character(s) $CIAID Set IATA Industrial 2 of 5 Label ID Character(s) 36 $C35ID S
Data Format Enter/Exit Programming Mode Label ID Symbology Selection − 1D Symbologies (continued) $CU2ID Set Industrial 2 of 5 Label ID Character(s) $CI2ID Set Interleaved 2 of 5 Label ID Character(s) $CISID Set ISBN Label ID Character(s) $CINID Set ISSN Label ID Character(s) $CPZID Set PZN Code Label ID Character(s) $CS2ID Set Standard 2 of 5 Label ID Character(s) $CCTID Set Trioptic Code Label ID Character(s) Programming Reference Guide $CGBID Set GTIN 8 Label ID Character(s) $CMSID Set MSI L
Enter/Exit Programming Mode Data Format Label ID Symbology Selection − 1D Symbologies (continued) $CABID Set UPC-A Label ID Character(s) $CE5ID Set UPC-E P5 Label ID Character(s) $CLPID Set LaPoste Code 39 Label ID Character(s) 38 HP Retail Integrated Barcode Scanner
Data Format Label ID Symbology Selection − 2D Symbologies $CAZID Set Aztec Label ID Character(s) $CCSID Set China Sensible Label ID Character(s) $CDMID Set Data Matrix Label ID Character(s) $CPNID Set Postnet Label ID Character(s) $CMXID Set Maxicode Label ID Character(s) $CP4ID Set PDF 417 Label ID Character(s) $CMIID Set Micro PDF 417 Label ID Character(s) $CQRID Set QR Code Label ID Character(s) $CPPID $CPJID Set Planet Postal Code Label ID Character(s) Set Japan Postal Code Label ID Charac
Data Format Case Conversion This feature allows conversion of the case of all alphabetic characters to upper or lower case. Case conversion affects ONLY scanned barcode data, and does not affect Label ID, Prefix, Suffix, or other appended data. $CLFCA00(CR) DEFAULT Case Conversion = Disable (no case conversion) $CLFCA01(CR) Case Conversion = Convert to upper case $CLFCA02(CR) Case Conversion = Convert to lower case Character Conversion Character conversion is an eight byte configuration item.
READING PARAMETERS DOUBLE READ TIMEOUT starting on page 42 LED AND BEEPER INDICATORS starting on page 44 •Power On Alert •Good Read: When to Indicate •Good Read Beep Type •Good Read Beep Frequency •Good Read Beep Length •Good Read Beep Volume •Good Read LED Duration SCANNING FEATURES starting on page 49 •Operating Mode •Scanning Active Time •Green Spot Duration •Mobile Phone Mode •Mobile Bias •Illumination Off Time •Illumination On Time •Presentation Illumination Control •Aiming Pointer •Aiming Duration T
Enter/Exit Programming Mode Reading Parameters Double Read Timeout Double Read Timeout prevents a double read of the same label by setting the minimum time allowed between reads of labels of the same symbology and data. If the unit reads a label and sees the same label again within the specified timeout, the second read is ignored. Double Read Timeout does not apply to scan modes that require a trigger pull for each label read. $CSNDR0A(CR) Double Read Timeout = 0.
Reading Parameters Enter/Exit Programming Mode Double Read Timeout (continued) $CSNDR50(CR) Double Read Timeout = 0.8 Second $CSNDR5A(CR) Double Read Timeout = 0.
Enter/Exit Programming Mode Reading Parameters LED AND BEEPER INDICATORS Power On Alert Disables or enables the indication (from the Beeper) that the scanner is receiving power. $CBPPU00(CR) Power On Alert = Disable (No Audible Indication) $CBPPU01(CR) DEFAULT Power On Alert = Power-up Beep Good Read: When to Indicate This feature specifies when the scanner will provide indication (beep and/or flash its green LED) upon successfully reading a barcode.
Reading Parameters Enter/Exit Programming Mode Good Read Beep Type Specifies whether the good read beep has a mono or bitonal beep sound. $CBPTY00(CR) DEFAULT Good Read Beep Type = Mono $CBPTY01(CR) Good Read Beep Type = Bitonal Good Read Beep Frequency Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.
Enter/Exit Programming Mode Reading Parameters Good Read Beep Length $CBPLE06(CR) Good Read Beep Length = 60 msec $CBPLE08(CR) DEFAULT Good Read Beep Length = 80 msec $CBPLE0A(CR) Good Read Beep Length = 100 msec $CBPLE0C(CR) Good Read Beep Length = 120 msec $CBPLE0E(CR) Good Read Beep Length = 140 msec $CBPLE10(CR) Good Read Beep Length = 160 msec $CBPLE12(CR) Good Read Beep Length = 180 msec $CBPLE14(CR) Good Read Beep Length = 200 msec 46 HP Retail Integrated Barcode Scanner
Reading Parameters Enter/Exit Programming Mode Good Read Beep Volume Selects the beeper volume (loudness) upon a good read beep. There are three selectable volume levels.
Enter/Exit Programming Mode Reading Parameters Good Read LED Duration This feature specifies the amount of time that the Good Read LED remains on following a good read. The good read LED on time can be set within a range of 100 milliseconds to 25,500 milliseconds (0.1 to 25.5 seconds) in 100ms increments. A setting of 00 keeps the LED on until the next trigger pull. See page 198 in “References” for detailed instructions and examples for setting this feature.
Reading Parameters Enter/Exit Programming Mode SCANNING FEATURES Operating Mode Selects the scanner’s scan operating mode. See page 199 in “References” for descriptions. $CSNRM02\r Automatic (Always On) $CSNRM03\r DEFAULT Automatic (Object Sense) Scanning Active Time This setting specifies the amount of time that the scanner stays in scan ON state once the state is entered. The range for this setting is from 1 to 255 seconds in 1-second increments.
Enter/Exit Programming Mode Reading Parameters Green Spot Duration Specifies the duration of the good read pointer beam after a good read. $CLSSP00(CR) Green Spot Duration = Disable (Green Spot is Off ) $CLSSP01(CR) DEFAULT Green Spot Duration = Short (300 msec) $CLSSP02(CR) Green Spot Duration = Medium (500 msec) $CLSSP03(CR) Green Spot Duration = Long (800 msec) Mobile Phone Mode This mode is useful for scanning barcodes displayed on a mobile phone.
Reading Parameters Enter/Exit Programming Mode Mobile Bias This variable mode alters scan module operation, optimizing barcode scanning for reading from mobile device displays rather than standard labels. The range for this setting is from 0 to 255. $CSILF00\r DEFAULT No Mobile Bias $CSILF Set Mobile Bias Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
Enter/Exit Programming Mode Reading Parameters Illumination On Time Defines the amount of time illumination is kept ON after a label is decoded. If an object is detected before Illumination ON expires, the timer is refreshed with the Object Gone timeout value. Range is 0 millisecond to 25.5 milliseconds in 100 millisecond intervals. This configuration is available in Automatic (Object Sense) only.
Reading Parameters Enter/Exit Programming Mode Aiming Pointer Enables/disables the aiming pointer for all symbologies. $CTAAP00(CR) Aiming Pointer = Disable $CTAAP01(CR) DEFAULT Aiming Pointer = Enable Aiming Duration Timer Specifies the frame of time the aiming pointer remains on after decoding a label, when in On Line or Serial On Line mode.The range for this setting is from 1 to 255 seconds in 1-second increments. See page 200 in “References” for a description of this feature.
Enter/Exit Programming Mode Reading Parameters Decode Negative Image Enable/Disable the ability to decode a negative image for all symbologies. When this feature is enabled, you will be unable to read normally-printed labels or programming labels in this manual. Scan the “Disable” barcode below to return the scanner to its default for this feature. To set decoding for only 2D codes, go to "2D Normal/Inverse Symbol Control" on page 149. For additional options, see the HP Configuration application.
Reading Parameters Enter/Exit Programming Mode MULTIPLE LABEL READING In standard (default) mode, when the scanner’s aiming system is activated by motion, it then acquires and processes each image in the area in front of it (the Volume). In this case, the scanner stops processing the image once it decodes a label. If several labels are present in the volume, only the first label encountered is decoded and sent.
Enter/Exit Programming Mode Reading Parameters Multiple Labels Ordering by Code Symbology This feature allows you to specify the order multiple labels are transmitted by symbology type, when Multiple Labels per Frame is enabled. See page 201 in “References” for detailed information on setting this feature. $CSNMS Select Symbologies for Multiple Labels Ordering Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
1D SYMBOLOGIES 1D Code Selection The scanner supports the following 1D symbologies (barcode types). See "2D Symbologies" starting on page 147 for 2D barcodes. Symbology-dependent options are included in each chapter.
Enter/Exit Programming Mode 1D Symbologies DISABLE ALL SYMBOLOGIES Use this feature to disable all symbologies. 1. Scan the ENTER/EXIT PROGRAMMING Mode barcode. 2. Scan the Disable All Symbologies barcode. 3. Complete the programming sequence by scanning the ENTER/EXIT PROGRAMMING barcode. $AD(CR) Disable All Symbologies This does not disable the reading of programming labels.
1D Symbologies Enter/Exit Programming Mode CODE EAN/UPC Coupon Control This feature is used to control the scanner’s method of processing coupon labels.
Enter/Exit Programming Mode 1D Symbologies UPC-A The following options apply to the UPC-A symbology. UPC-A Enable/Disable When disabled, the scanner will not read UPC-A barcodes. $CABEN00(CR) UPC-A = Disable $CABEN01(CR) DEFAULT UPC-A = Enable UPC-A Check Character Transmission Enable this option to transmit the check character along with UPC-A barcode data.
1D Symbologies Enter/Exit Programming Mode Expand UPC-A to EAN-13 Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. $CAB3B00(CR) DEFAULT UPC-A to EAN-13 = Don’t Expand $CAB3B01(CR) UPC-A to EAN-13 = Expand UPC-A Number System Character Transmission This feature enables/disables transmission of the UPC-A number system character.
Enter/Exit Programming Mode 1D Symbologies UPC-A 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded. $CAB2D00(CR) DEFAULT EAN-13 2D Component = Disable (2D component not required) $CAB2D01(CR) EAN-13 2D Component = 2D component must be decoded UPC-E The following options apply to the UPC-E symbology. UPC-E Enable/Disable When disabled, the scanner will not read UPC-E barcodes.
1D Symbologies Enter/Exit Programming Mode UPC-E Check Character Transmission Enable this option to transmit the check character along with UPC-E barcode data. $CEBCT00(CR) UPC-E Check Character Transmission = Don’t Send $CEBCT01(CR) DEFAULT UPC-E Check Character Transmission = Send UPC-E 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label for this symbology is decoded.
Enter/Exit Programming Mode 1D Symbologies Expand UPC-E to EAN-13 Expands UPC-E data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. $CEB3B00(CR) DEFAULT UPC-E to EAN-13 = Don’t Expand $CEB3B01(CR) UPC-E to EAN-13 = Expand Expand UPC-E to UPC-A Expands UPC-E data to the UPC-A data format.
1D Symbologies Enter/Exit Programming Mode UPC-E Number System Character Transmission This feature enables/disables transmission of the UPC-E system number character. $CEBNS00(CR) UPC-E Number System Character = Do not transmit $CEBNS01(CR) DEFAULT UPC-E Number System Character = Transmit GTIN FORMATTING This feature enables/disables the ability to convert UPC-E, UPC-A, EAN 8, and EAN 13 labels into the GTIN 14-character format.
Enter/Exit Programming Mode 1D Symbologies EAN 13 (JAN 13) The following options apply to the EAN 13 (Jan 13) symbology. EAN 13 Enable/Disable When disabled, the scanner will not read EAN 13/JAN 13 barcodes. $C3BEN00(CR) EAN 13 = Disable $C3BEN01(CR) DEFAULT EAN 13 = Enable EAN 13 Check Character Transmission Enable this option to transmit the check character along with EAN 13 barcode data.
1D Symbologies Enter/Exit Programming Mode EAN-13 Flag 1 Character Enables/disables transmission of an EAN/JAN13 Flag1 character. The Flag 1 character is the first character of the label. $C3BF100(CR) EAN-13 Flag 1 Char= Don’t transmit $C3BF101(CR) DEFAULT EAN-13 Flag 1 Char= Transmit EAN-13 ISBN Conversion This option enables/disables conversion of EAN 13/JAN 13 Bookland labels starting with 978 to ISBN labels.
Enter/Exit Programming Mode 1D Symbologies EAN-13 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded. $C3B2D00(CR) DEFAULT EAN-13 2D Component = Disable (2D component not required) $C3B2D01(CR) EAN-13 2D Component = 2D component must be decoded ISSN The following options apply to the ISSN symbology. ISSN Enable/Disable Enables/disables conversion of EAN/JAN13 Bookland labels starting with 977 to ISSN labels.
1D Symbologies Enter/Exit Programming Mode EAN 8 (JAN 8) The following options apply to the EAN 8 (Jan 8) symbology. EAN 8 Enable/Disable When disabled, the scanner will not read EAN 8/JAN 8 barcodes. $C8BEN00(CR) EAN 8 = Disable $C8BEN01(CR) DEFAULT EAN 8 = Enable EAN 8 Check Character Transmission Enable this option to transmit the check character along with EAN 8 barcode data.
Enter/Exit Programming Mode 1D Symbologies Expand EAN 8 to EAN 13 Enable this option to expand EAN 8/JAN 8 labels to EAN 13/JAN 13. $C8B3B00(CR) DEFAULT Expand EAN 8 to EAN 13 = Disable $C8B3B01(CR) Expand EAN 8 to EAN 13 = Enable EAN 8 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label for this symbology is decoded.
1D Symbologies Enter/Exit Programming Mode UPC/EAN GLOBAL SETTINGS This section provides configuration settings for UPC-A, UPC-E, EAN 13 and EAN 8 symbologies, and affects all of these unless otherwise marked for each feature description. UPC/EAN Price Weight Check This feature enables/disables calculation and verification of price/weight check digits.
Enter/Exit Programming Mode 1D Symbologies UPC/EAN Quiet Zones This feature specifies the number of quiet zones for UPC/EAN labels. Quiet zones are blank areas at the ends of a barcode, typically 10 times the width of the narrowest bar or space in the label. The property applies to all EAN-UPC symbologies globally and to the ADDONs.
1D Symbologies Enter/Exit Programming Mode ADD-ONS Contact Customer Support for advanced programming of optional and conditional add-ons. Optional Add-ons The scanner can be enabled to optionally read the following add-ons (supplementals): If a UPC/EAN base label and an add-on are both decoded, the scanner will transmit the base label and add-on. If a UPC/EAN base label is decoded without an add-on, the base label will be transmitted without an add-on.
Enter/Exit Programming Mode 1D Symbologies Optional Add-On Timer This option sets the time the scanner will look for an add-on when an add-on fragment has been seen and optional add-ons are enabled. (Also see "Optional GS1-128 Add-On Timer" on page 77.
1D Symbologies Enter/Exit Programming Mode Optional Add-On Timer (continued) $CADOT06(CR) Optional Add-on Timer = 60ms $CADOT07(CR) DEFAULT Optional Add-on Timer = 70ms $CADOT0A(CR) Optional Add-on Timer = 100ms $CADOT0C(CR) Optional Add-on Timer = 120ms $CADOT0E(CR) Optional Add-on Timer = 140ms $CADOT10(CR) Optional Add-on Timer = 160ms Programming Reference Guide 75
Enter/Exit Programming Mode 1D Symbologies Optional Add-On Timer (continued) $CADOT12(CR) Optional Add-on Timer = 180ms $CADOT14(CR) Optional Add-on Timer = 200ms $CADOT16(CR) Optional Add-on Timer = 220ms $CADOT18(CR) Optional Add-on Timer = 240ms $CADOT1A(CR) Optional Add-on Timer = 260ms $CADOT1C(CR) Optional Add-on Timer = 280ms $CADOT1E(CR) Optional Add-on Timer = 300ms 76 HP Retail Integrated Barcode Scanner
1D Symbologies Enter/Exit Programming Mode Optional GS1-128 Add-On Timer This option sets the timer expiration value to read the added part after reading the linear EAN/UPC part. For UPC/EAN add-ons other than those of that type, see "Optional Add-On Timer" on page 74.
Enter/Exit Programming Mode 1D Symbologies Optional GS1-128 Add-On Timer (continued) $CADUT06(CR) Optional GS1-128 Add-On Timer = 60ms $CADUT07(CR) Optional GS1-128 Add-On Timer = 70ms $CADUT0A(CR) Optional GS1-128 Add-On Timer = 100ms $CADUT0C(CR) Optional GS1-128 Add-On Timer = 120ms $CADUT0E(CR) Optional GS1-128 Add-On Timer = 140ms $CADUT10(CR) Optional GS1-128 Add-On Timer = 160ms 78 HP Retail Integrated Barcode Scanner
1D Symbologies Enter/Exit Programming Mode Optional GS1-128 Add-On Timer (continued) $CADUT12(CR) Optional GS1-128 Add-On Timer = 180ms $CADUT14(CR) Optional GS1-128 Add-On Timer = 200ms $CADUT16(CR) Optional GS1-128 Add-On Timer = 220ms $CADUT18(CR) Optional GS1-128 Add-On Timer = 240ms $CADUT1A(CR) Optional GS1-128 Add-On Timer = 260ms $CADUT1C(CR) Optional GS1-128 Add-On Timer = 280ms $CADUT1E(CR) Optional GS1-128 Add-On Timer = 300ms Programming Reference Guide 79
Enter/Exit Programming Mode 1D Symbologies CODE 39 The following options apply to the Code 39 symbology. Code 39 Enable/Disable $CC3EN00(CR) Code 39 = Disable $CC3EN01(CR) DEFAULT Code 39 = Enable Code 39 Check Character Calculation Enable this option to enables/disables calculation and verification of an optional Code 39 check character.
1D Symbologies Enter/Exit Programming Mode Code 39 Check Character Calculation (continued) $CC3CC04(CR) Code 39 Check Character Calculation = Enable Italian Post Check $CC3CC08(CR) Code 39 Check Character Calculation = Enable Daimler Chrysler Check Code 39 Check Character Transmission Enable this option to transmit the check character along with Code 39 barcode data.
Enter/Exit Programming Mode 1D Symbologies Code 39 Start/Stop Character Transmission Enable this option to enable/disable transmission of Code 39 start and stop characters. $CC3SS00(CR) DEFAULT Code 39 Start/Stop Character Transmission = Don’t Transmit $CC3SS01(CR) Code 39 Start/Stop Character Transmission = Transmit Code 39 Full ASCII Enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters.
1D Symbologies Enter/Exit Programming Mode Code 39 Quiet Zones This feature specifies the number of quiet zones for Code 39 labels. Quiet zones are blank areas at the ends of a barcode, typically 10 times the width of the narrowest bar or space in the label.
Enter/Exit Programming Mode 1D Symbologies Code 39 Set Length 1 This feature specifies one of the barcode lengths for Code 39 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 0 to 50 characters. Table 3 provides examples for setting Length 1. See page 188 for detailed instructions on setting this feature. Table 3.
1D Symbologies Enter/Exit Programming Mode Code 39 Set Length 2 This feature specifies one of the barcode lengths for Code 39 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. Table 4 provides examples for setting Length 2. See page 188 for detailed instructions on setting this feature. Table 4.
Enter/Exit Programming Mode 1D Symbologies CODE 32 (ITAL PHARMACEUTICAL CODE) The following options apply to the Code 32 (Italian Pharmaceutical Code) symbology. Code 32 Enable/Disable When disabled, the scanner will not read Code 32 barcodes.
1D Symbologies Enter/Exit Programming Mode Code 32 Start/Stop Character Transmission This option enables/disables transmission of Code 32 start and stop characters. $CP3SS00(CR) DEFAULT Code 32 Start/Stop Character Transmission = Don’t Transmit $CP3SS01(CR) Code 32 Start/Stop Character Transmission = Transmit CODE 39 CIP (FRENCH PHARMACEUTICAL) The following options apply to the Code 39 CIP symbology. Code 39 CIP Enable/Disable Enables/Disables ability of the scanner to decode Code 39 CIP labels.
Enter/Exit Programming Mode 1D Symbologies CODE 39 LAPOSTE The following options apply to the Code 39 LaPoste symbology. Code 39 LaPoste Enable/Disable Enables/disables the ability of the scanner to decode Code39 La Poste labels. $CLPEN00(CR) DEFAULT Code 39 LaPoste = Disable $CLPEN01(CR) Code 39 LaPoste = Enable CODE 128 The following options apply to the Code 128 symbology. Code 128 Enable/Disable When disabled, the scanner will not read Code 128 barcodes.
1D Symbologies Enter/Exit Programming Mode Expand Code 128 to Code 39 This feature enables/disables expansion of Code 128 labels to Code 39 labels. $CC8C300(CR) DEFAULT Code 128 to Code 39 = Don’t Expand $CC8C301(CR) Code 128 to Code 39 = Expand Code 128 Check Character Transmission Enable this option to transmit the check character along with Code 128 barcode data.
Enter/Exit Programming Mode 1D Symbologies Code 128 Function Character Transmission Enables/disables transmission of Code128 function characters 1, 2, 3, and 4. $CC8TF00(CR) DEFAULT Code 128 Function Character Transmission = Don’t Send $CC8TF01(CR) Code 128 Function Character Transmission = Send Code 128 Sub-Code Exchange Transmission Enables/disables the transmission of “Sub-Code Exchange” characters (NOT transmitted by standard decoding).
1D Symbologies Enter/Exit Programming Mode Code 128 Quiet Zones This feature specifies the number of quiet zones for Code 128 labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 times the width of the narrowest bar or space in the label.
Enter/Exit Programming Mode 1D Symbologies Code 128 Set Length 1 Specifies one of the barcode lengths for Code 128 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 50 characters. Table 5 provides some examples for setting Length 1. See page 188 for detailed instructions on setting this feature. Table 5.
1D Symbologies Enter/Exit Programming Mode Code 128 Set Length 2 This feature specifies one of the barcode lengths for Code 128 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 6 provides examples for setting Length 2.
Enter/Exit Programming Mode 1D Symbologies GS1-128 The following options apply to the GS1-128 symbology. (Also known as USS-128, GS1128, GTIN-128, UCC-128, EAN-128.) GS1-128 Enable This option enables/disables the ability of the scanner to translate GS1-128 labels to the GS1-128 data format. Options are: • Transmit GS1-128 labels in Code 128 data format. • Transmit GS1-128 labels in GS1-128 data format. • Do not transmit GS1-128 labels.
1D Symbologies Enter/Exit Programming Mode CODE ISBT 128 The following options apply to the ISBT 128 symbology. ISBT 128 Concatenation Use this option to enable/disable ISBT128 concatenation of 2 labels. $CI8CE00(CR) DEFAULT ISBN 128 Concatenation = Disable $CI8CE01(CR) ISBN 128 Concatenation = Enable ISBT 128 Force Concatenation When enabled, this feature forces concatenation for ISBT. This option is only valid when ISBT 128 Concatenation is enabled.
Enter/Exit Programming Mode 1D Symbologies ISBT 128 Concatenation Mode Specifies the concatenation mode between Static and Dynamic. This option is only valid when ISBT 128 Concatenation is enabled (see "ISBT 128 Concate- nation" on page 95).
1D Symbologies Enter/Exit Programming Mode ISBT 128 Dynamic Concatenation Timeout Specifies the timeout used by the ISBT 128 Dynamic Concatenation Mode.
Enter/Exit Programming Mode 1D Symbologies INTERLEAVED 2 OF 5 (I 2 OF 5) The following options apply to the I 2 of 5 symbology. I 2 of 5 Enable/Disable When disabled, the scanner will not read I 2 of 5 barcodes.
1D Symbologies Enter/Exit Programming Mode I 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional I 2 of 5 check character. Combinations of these settings are possible via the HP configuration utility, or contact Technical Support.
Enter/Exit Programming Mode 1D Symbologies I 2 of 5 Check Character Transmission Enable this option to transmit the check character along with I 2 of 5 barcode data. $CI2CT00(CR) I 2 of 5 Check Character Transmission = Don’t Send $CI2CT01(CR) DEFAULT I 2 of 5 Check Character Transmission = Send I 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the I 2 of 5 symbology.
1D Symbologies Enter/Exit Programming Mode I 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for I 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. The length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters in increments of two. Table 7 provides some examples for setting Length 1. See page 188 for detailed instructions on setting this feature.
Enter/Exit Programming Mode 1D Symbologies I 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for I 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. The length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 8 provides examples for setting Length 2.
1D Symbologies Enter/Exit Programming Mode FOLLETT 2 OF 5 The following options apply to the Follett 2 of 5 symbology. Follett 2 of 5 Enable/Disable Enables/Disables ability of the scanner to decode Plessey labels.
Enter/Exit Programming Mode 1D Symbologies STANDARD 2 OF 5 The following options apply to the Standard 2 of 5 symbology. Standard 2 of 5 Enable/Disable When disabled, the scanner will not read Standard 2 of 5 barcodes. $C2SEN00(CR) DEFAULT Standard 2 of 5 = Disable $C2SEN01(CR) Standard 2 of 5 = Enable Standard 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional Standard 2 of 5 check character.
1D Symbologies Enter/Exit Programming Mode Standard 2 of 5 Check Character Transmission This feature enables/disables transmission of an optional Standard 2 of 5 check character. $CS2CT00(CR) Standard 2 of 5 Check Character Transmission = Don’t Send $CS2CT01(CR) DEFAULT Standard 2 of 5 Check Character Transmission = Send Standard 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the Standard 2 of 5 symbology.
Enter/Exit Programming Mode 1D Symbologies Standard 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for Standard 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 1 to 50 characters. Table 9 provides some examples for setting Length 1. See page 188 if you want detailed instructions on setting this feature.
1D Symbologies Enter/Exit Programming Mode Standard 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Standard 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 10 provides examples for setting Length 2.
Enter/Exit Programming Mode 1D Symbologies INDUSTRIAL 2 OF 5 The following options apply to the Industrial 2 of 5 symbology. Industrial 2 of 5 Enable/Disable Enables/Disables ability of the scanner to decode Industrial 2 of 5 labels. $CU2EN00(CR) DEFAULT Industrial 2 of 5 = Disable $CU2EN01(CR) Industrial 2 of 5 = Enable Industrial 2 of 5 Check Character Calculation Enables/Disables calculation and verification of an optional Industrial 2 of 5 check character.
1D Symbologies Enter/Exit Programming Mode Industrial 2 of 5 Check Character Transmission Enables/disables transmission of an Industrial 2 of 5 check character. $CU2CT00(CR) Industrial 2 of 5 Check Character Transmission = Disable $CU2CT01(CR) DEFAULT Industrial 2 of 5 Check Character Transmission = Enable Industrial 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the Industrial 2 of 5 symbology.
Enter/Exit Programming Mode 1D Symbologies Industrial 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for Industrial 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 0 to 50 characters. Table 11 provides some examples for setting Length 1. See page 188 if you want detailed instructions on setting this feature.
1D Symbologies Enter/Exit Programming Mode Industrial 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Industrial 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. The length can be set from 1 to 50 characters.
Enter/Exit Programming Mode 1D Symbologies CODE IATA The following options apply to the IATA symbology. IATA Enable/Disable Enables/Disables the ability of the scanner to decode IATA labels. $CIAEN00(CR) DEFAULT IATA = Disable $CIAEN01(CR) IATA = Enable IATA Check Character Transmission Enables/Disables calculation and verification of an optional Industrial 2 of 5 check character.
1D Symbologies Enter/Exit Programming Mode CODABAR The following options apply to the Codabar symbology. Codabar Enable/Disable When disabled, the scanner will not read Codabar barcodes. $CCBEN00(CR) DEFAULT Codabar = Disable $CCBEN01(CR) Codabar = Enable Codabar Check Character Calculation Enable this option to enables/disables calculation and verification of an optional Codabar check character.
Enter/Exit Programming Mode 1D Symbologies Codabar Check Character Transmission Enable this option to transmit the check character along with Codabar barcode data. $CCBCT00(CR) Codabar Check Character Transmission = Don’t Send $CCBCT01(CR) DEFAULT Codabar Check Character Transmission = Send Codabar Start/Stop Character Transmission Enable this option to enable/disable transmission of Codabar start and stop characters.
1D Symbologies Enter/Exit Programming Mode Codabar Start/Stop Character Set This option specifies the format of transmitted Codabar start/stop characters. $CCBSC00(CR) Codabar Check Character Set = ABCD/TN*E $CCBSC01(CR) Codabar Check Character Set = ABCD/ABCD $CCBSC02(CR) Codabar Check Character Set = abcd/tn*e $CCBSC03(CR) DEFAULT Codabar Check Character Set = abcd/abcd Codabar Start/Stop Character Match When enabled, this option requires that start and stop characters match.
Enter/Exit Programming Mode 1D Symbologies Codabar Quiet Zones Specifies the number of quiet zones for Codabar labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 times the width of the narrowest bar or space in the label.
1D Symbologies Enter/Exit Programming Mode Codabar Set Length 1 This feature specifies one of the barcode lengths for Codabar Length ControlCodabar Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s start, stop, check and data characters. The length must include at least one data character. The length can be set from 3 to 50 characters. Table 13 provides some examples for setting Length 1.
Enter/Exit Programming Mode 1D Symbologies Codabar Set Length 2 This feature specifies one of the barcode lengths for Codabar Length ControlCodabar Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. The length includes the barcode’s start, stop, check and data characters. The length must include at least one data character. The length can be set from 3 to 50 characters.
1D Symbologies Enter/Exit Programming Mode ABC CODABAR The following options apply to the ABC Codabar symbology. ABC Codabar Enable/Disable Enables/Disables ability of the scanner to decode ABC Codabar labels. $CCBAB00(CR) DEFAULT ABC Codabar = Disable $CCBAB01(CR) ABC Codabar = Enable ABC Codabar Concatenation Mode Specifies the concatenation mode between Static and Dynamic.
Enter/Exit Programming Mode 1D Symbologies ABC Codabar Dynamic Concatenation Timeout Specifies the timeout in 10-millisecond ticks used by the ABC Codabar Dynamic Concatenation Mode.
1D Symbologies Enter/Exit Programming Mode ABC Codabar Force Concatenation Forces labels starting or ending with D to be concatenated.
Enter/Exit Programming Mode 1D Symbologies CODE 11 The following options apply to the Code 11 symbology. Code 11 Enable/Disable When disabled, the scanner will not read Code 11 barcodes. $CC1EN00(CR) DEFAULT Code 11 = Disable $CC1EN01(CR) Code 11 = Enable Code 11 Check Character Calculation This option enables/disables calculation and verification of optional Code 11 check character.
1D Symbologies Enter/Exit Programming Mode Code 11 Check Character Transmission This feature enables/disables transmission of an optional Code 11 check character. $CC1CT00(CR) Code 11 Check Character Transmission = Don’t Send $CC1CT01(CR) DEFAULT Code 11 Check Character Transmission = Send Code 11 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 11 symbology.
Enter/Exit Programming Mode 1D Symbologies Code 11 Set Length 1 This feature specifies one of the barcode lengths for Code 11 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. Table 15 provides some examples for setting Length 1. See page 188 for detailed instructions on setting this feature. Table 15.
1D Symbologies Enter/Exit Programming Mode Code 11 Set Length 2 This feature specifies one of the barcode lengths for Code 11 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 16 provides examples for setting Length 2.
Enter/Exit Programming Mode 1D Symbologies GS1 DATABAR™ OMNIDIRECTIONAL The following options apply to the GS1 DataBar™ Omnidirectional (formerly RSS-14) symbology. GS1 DataBar™ Omnidirectional Enable/Disable When disabled, the scanner will not read GS1 DataBar™ Omnidirectional barcodes.
1D Symbologies Enter/Exit Programming Mode GS1 DataBar™ Omnidirectional 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label for this symbology is decoded.
Enter/Exit Programming Mode 1D Symbologies GS1 DataBar™ Expanded GS1-128 Emulation When enabled, GS1 DataBar™ Expanded barcodes will be translated to the GS1-128 label data format. $CXBU800(CR) DEFAULT GS1 DataBar™ Expanded GS1-128 Emulation = Disable $CXBU801(CR) GS1 DataBar™ Expanded GS1-128 Emulation = Enable GS1 DataBar™ Expanded 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded.
1D Symbologies Enter/Exit Programming Mode GS1 DataBar™ Expanded Length Control This feature specifies either variable length decoding or fixed length decoding for the GS1 DataBar™ Expanded symbology. Variable Length: For variable-length decoding, a minimum length may be set. Fixed Length: For fixed-length decoding, two different lengths may be set.
Enter/Exit Programming Mode 1D Symbologies GS1 DataBar™ Expanded Set Length 1 This feature specifies one of the barcode lengths for GS1 DataBar™ Expanded Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 74 characters. Table 17 provides some examples for setting Length 1. See page 188 for detailed instructions on setting this feature.
1D Symbologies Enter/Exit Programming Mode GS1 DataBar™ Expanded Set Length 2 This feature specifies one of the barcode lengths for GS1 DataBar™ Expanded Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 74 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 18 provides examples for setting Length 2.
Enter/Exit Programming Mode 1D Symbologies GS1 DATABAR™ LIMITED The following options apply to the GS1 DataBar™ Limited (formerly RSS Limited) symbology. GS1 DataBar™ Limited Enable/Disable When disabled, the scanner will not read GS1 DataBar™ Limited barcodes. $CLBEN00(CR) DEFAULT GS1 DataBar™ Limited = Disable $CLBEN01(CR) GS1 DataBar™ Limited = Enable GS1 DataBar™ Limited GS1-128 Emulation When enabled, GS1 DataBar™ Limited barcodes will be translated to the GS1-128 label data format.
1D Symbologies Enter/Exit Programming Mode GS1 DataBar™ Limited 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded. $CLB2D00(CR) DEFAULT GS1 DataBar™ Limited 2D Component = Disable (2D component not required) $CLB2D01(CR) GS1 DataBar™ Limited 2D Component = 2D component must be decoded CODE 93 The following options apply to the Code 93 symbology.
Enter/Exit Programming Mode 1D Symbologies Code 93 Check Character Calculation Enables/disables calculation and verification of an optional Code 93 check character.
1D Symbologies Enter/Exit Programming Mode Code 93 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 93 symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
Enter/Exit Programming Mode 1D Symbologies Code 93 Set Length 1 Specifies one of the barcode lengths for Code 93 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 01 to 50 characters. Table 19 provides some examples for setting Length 1. See page 188 for detailed instructions on setting this feature. Table 19.
1D Symbologies Enter/Exit Programming Mode Code 93 Set Length 2 This feature specifies one of the barcode lengths for Code 93 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length).
Enter/Exit Programming Mode 1D Symbologies Code 93 Quiet Zones Enables/disables quiet zones for Code 93. $CC9LO02(CR) Code 93 Quiet Zones = Quiet Zones on two sides $CC9LO03(CR) DEFAULT Code 93 Quiet Zones = Small Quiet Zones on two sides MSI The following options apply to the MSI symbology. MSI Enable/Disable Enables/Disables ability of the scanner to decode MSI labels.
1D Symbologies Enter/Exit Programming Mode MSI Check Character Calculation Enables/Disables calculation and verification of an optional MSI check character. $CMSCC00(CR) MSI Check Character Calculation = Disable $CMSCC01(CR) DEFAULT MSI Check Character Calculation = Enable Mod10 $CMSCC02(CR) MSI Check Character Calculation = Enable Mod11/10 $CMSCC03(CR) MSI Check Character Calculation = Enable Mod10/10 MSI Check Character Transmission Enables/disables transmission of an MSI check character.
Enter/Exit Programming Mode 1D Symbologies MSI Length Control This feature specifies either variable length decoding or fixed length decoding for the MSI symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
1D Symbologies Enter/Exit Programming Mode MSI Set Length 1 This feature specifies one of the barcode lengths for MSI Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 01 to 50 characters. Table 21 provides some examples for setting Length 1. See page 188 for detailed instructions on setting this feature. Table 21.
Enter/Exit Programming Mode 1D Symbologies MSI Set Length 2 This feature specifies one of the barcode lengths for MSI Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length).
1D Symbologies Enter/Exit Programming Mode PLESSEY The following options apply to the Plessey symbology. Plessey Enable/Disable Enables/Disables ability of the scanner to decode Plessey labels. $CPLEN00CR) DEFAULT Plessey = Disable $CPLEN01CR) Plessey = Enable Plessey Check Character Calculation Enables/Disables calculation and verification of an optional Plessey check character.
Enter/Exit Programming Mode 1D Symbologies Plessey Check Character Transmission Enables/disables transmission of an MSI check character. $CPLCT00(CR) Plessey Check Character Transmission = Disable $CPLCT01(CR) DEFAULT Plessey Check Character Transmission = Enable Plessey Length Control This feature specifies either variable length decoding or fixed length decoding for the Plessey symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set.
1D Symbologies Enter/Exit Programming Mode Plessey Set Length 1 This feature specifies one of the barcode lengths for Plessey Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 01 to 50 characters. Table 23 provides some examples for setting Length 1. See page 188 for detailed instructions on setting this feature. Table 23.
Enter/Exit Programming Mode 1D Symbologies Plessey Set Length 2 This feature specifies one of the barcode lengths for Plessey Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length).
2D SYMBOLOGIES • • 2D Global Features 2D Maximum Decoding Time on • 2D Normal/Inverse Symbol Control on page 148 page 149 2D Structured Append on page 149 2D Symbologies The scanner supports the following 2D symbologies (barcode types). Symbology-dependent options for each symbology are included in this chapter. See "1D Code Selection" starting on page 57 for configuration of 1D barcodes.
Enter/Exit Programming Mode 2D Symbologies 2D Maximum Decoding Time This feature specifies the maximum amount of time the software will spend attempting to decode a 2D label. The selectable range is 10 milliseconds to 2.55 seconds.
2D Symbologies Enter/Exit Programming Mode 2D Structured Append Enables/disables ability of the scanner to append multiple 2D Codes labels in a structured format.
Enter/Exit Programming Mode 2D Symbologies Aztec Code Aztec Code Enable / Disable Enables/disables the ability of the scanner to decode Aztec Code labels. $CAZEN00(CR) Aztec Code = Disable $CAZEN01(CR) DEFAULT Aztec Code = Enable Aztec Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set.
2D Symbologies Enter/Exit Programming Mode Aztec Code Set Length 1 Specifies one of the barcode lengths for Aztec Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 3,832 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
Enter/Exit Programming Mode 2D Symbologies Aztec Code Set Length 2 This feature specifies one of the barcode lengths for Aztec Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 3,832 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
2D Symbologies Enter/Exit Programming Mode China Sensible Code China Sensible Code Enable / Disable Enables/disables the ability of the scanner to decode China Sensible Code labels. $CCSEN00(CR) DEFAULT China Sensible Code = Disable $CCSEN01(CR) China Sensible Code = Enable China Sensible Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set.
Enter/Exit Programming Mode 2D Symbologies China Sensible Code Set Length 1 Specifies one of the barcode lengths for China Sensible Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 7,827 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
2D Symbologies Enter/Exit Programming Mode China Sensible Code Set Length 2 This feature specifies one of the barcode lengths for China Sensible Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 7,827 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
Enter/Exit Programming Mode 2D Symbologies Data Matrix Data Matrix Enable / Disable Enables/disables ability of the scanner to decode Data Matrix labels. $CDMEN00(CR) Data Matrix = Disable $CDMEN01(CR) DEFAULT Data Matrix = Enable Data Matrix Square/Rectangular Style Specifies the options available when reading Data Matrix with different form factors.
2D Symbologies Enter/Exit Programming Mode Data Matrix Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
Enter/Exit Programming Mode 2D Symbologies Data Matrix Set Length 2 This feature specifies one of the barcode lengths for Data Matrix Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 3,116 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
2D Symbologies Enter/Exit Programming Mode Maxicode Maxicode Enable / Disable Enables/disables ability of the scanner to decode Maxicode labels. $CMXEN00(CR) DEFAULT Maxicode = Disable $CMXEN01(CR) Maxicode = Enable Maxicode Primary Message Transmission Enables/disables the transmission of only the Primary Message when the Secondary Message is not readable.
Enter/Exit Programming Mode 2D Symbologies Maxicode Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
2D Symbologies Enter/Exit Programming Mode Maxicode Set Length 2 This feature specifies one of the barcode lengths for Maxicode Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 0145 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
Enter/Exit Programming Mode 2D Symbologies PDF417 PDF417 Enable / Disable Enables/disables the ability of the scanner to decode PDF417 labels. $CP4EN00(CR) PDF417 = Disable $CP4EN01(CR) DEFAULT PDF417 = Enable PDF417 Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
2D Symbologies Enter/Exit Programming Mode PDF417 Set Length 1 Specifies one of the barcode lengths for PDF417 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. Characters can be set from 0001 to 2,710 characters (pad with zeroes) in increments of 01. Any value greater than 2,710 will be considered to be 2,710. See page 188 for detailed instructions on setting this feature.
Enter/Exit Programming Mode 2D Symbologies PDF417 Set Length 2 This feature specifies one of the barcode lengths for PDF417 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. Characters can be set from 01 to 2,710 characters (pad with zeroes) in increments of 01.
2D Symbologies Enter/Exit Programming Mode Micro PDF417 Micro PDF417 Enable / Disable Enables/disables the ability of the scanner to decode Micro PDF417 labels. $CMIEN00(CR) DEFAULT Micro PDF417 = Disable $CMIEN01(CR) Micro PDF417 = Enable Micro PDF417 Code 128 GS1-128 Emulation Specifies which AIM ID to use for MicroPDF labels when doing Code 128 or GS1-128 emulation.
Enter/Exit Programming Mode 2D Symbologies Micro PDF417 Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
2D Symbologies Enter/Exit Programming Mode Micro PDF417 Set Length 2 This feature specifies one of the barcode lengths for Micro PDF417 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length includes the barcode’s data characters only. Characters can be set from 0001 to 0366 characters (pad with zeroes) in increments of 01. Any value greater than 0366 will be considered to be 0366.
Enter/Exit Programming Mode 2D Symbologies QR Code QR Code Enable / Disable Enables/disables the ability of the scanner to decode QR Code labels. $CQREN00(CR) QR Code = Disable $CQREN01(CR) DEFAULT QR Code = Enable QR Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
2D Symbologies Enter/Exit Programming Mode QR Code Set Length 1 Specifies one of the barcode lengths for QR Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 7,089 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
Enter/Exit Programming Mode 2D Symbologies QR Code Set Length 2 This feature specifies one of the barcode lengths for QR Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 7,089 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
2D Symbologies Enter/Exit Programming Mode Micro QR Code Micro QR Code Enable/Disable Enables/disables the ability of the scanner to decode Micro QR Code labels. MQEN00 DEFAULT Micro QR Code = Disable MQEN01 Micro QR Code = Enable Micro QR Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set.
Enter/Exit Programming Mode 2D Symbologies Micro QR Code Set Length 1 Specifies one of the barcode lengths for Micro QR Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 0035 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
2D Symbologies Enter/Exit Programming Mode Micro QR Code Set Length 2 This feature specifies one of the barcode lengths for Micro QR Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 0035 characters in increments of 0001 (pad with zeroes). See page 188 for detailed instructions on setting this feature.
Enter/Exit Programming Mode 2D Symbologies UCC Composite UCC Composite Enable / Disable Enables/disables the ability of the scanner to decode the stacked part of a UCC Composite label. This feature is not effective when Global AIM IDs are enabled (see "Global AIM ID" on page 30).
2D Symbologies Enter/Exit Programming Mode UCC Optional Composite Timer Specifies the amount of time the system will wait for the stacked part of a UCC Composite label before transmitting the linear label without an add-on.
Enter/Exit Programming Mode 2D Symbologies Postal Code Selection Enables/disables the ability of the scanner to decode labels of a specific postal symbology.
2D Symbologies Enter/Exit Programming Mode Postal Code Selection (continued) $CPOEN06(CR) Postal Code Selection = Enable Japan Post $CPOEN07(CR) Postal Code Selection = Enable IMB $CPOEN08(CR) Postal Code Selection = Enable Sweden Post $CPOEN09(CR) Postal Code Selection = Enable Portugal Post Postnet BB Control Controls the ability of the scanner to decode B and B' fields of Postnet labels.
2D Symbologies NOTES 178 HP Retail Integrated Barcode Scanner
Chapter 4 References This section contains explanations and examples of selected barcode features. See "Configuration Using Barcodes" starting on page 9 for the actual barcode labels used to configure the scanner.
References USB-COM Parameters Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. To set the delay: 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 10 (setting is in 10ms increments). Pad the result with leading zeroes to yield two digits.
USB-COM Parameters ACK NAK Options This enables/disables the ability of the scanner to support the ACK/NAK protocol. When configured, the scanner and/or host sends an “ACK” when it receives data properly, and sends “NAK” when the data is in error. Options are: • Disable • Enable for label transmission — The scanner expects an ACK/NAK response from the host when a label is sent. • Enable for host-command acknowledge — The scanner will respond with ACK/NAK when the host sends a command.
References NAK Character This setting specifies an ASCII character or hex value to be used as the NAK character. ASCII characters or any hex value from 0 to 0xFF can be selected. To set this feature: 1. Determine the desired character or value. 2. Use the ASCII Chart on the inside back cover of this manual to find the hex equivalent for the desired character/value. 3. Go to page 17 and scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4. Scan the barcode: SELECT NAK CHARACTER SETTING.
USB-COM Parameters ACK NAK Timeout Value This option specifies the amount of time the scanner waits for an ACK character from the host following label transmission. The selectable timeout range is 200 milliseconds to 15,000ms (15 seconds) in 200ms increments. A selection of 0 disables the timeout. To set this value: 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 200 (setting is in 200ms increments). Pad the result with leading zeroes to yield two digits.
References ACK NAK Retry Count This feature specifies the number of times the scanner retries a label transmission due to a retry condition. The selectable range is from 1 to 254 retries. A selection of 0 disables the count, and a selection of 255 specifies unlimited retries. To set this feature: 1. Determine the desired setting. 2. Pad the number with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20 = 020, etc. 3.
USB-COM Parameters Disable Character Specifies the value of the host command used to disable the scanner. ASCII characters or any hex value from 0 to 0xFF can be selected. To set the value: 1. Determine the desired character or value. A setting of 0xFF indicates the Disable Character is not used (not available). 2. Use the ASCII Chart on the inside back cover of this manual to find the hex equivalent for the desired character/value. 3.
References Enable Character Specifies the value of the host command used to enable the scanner. ASCII characters or any hex value from 0 to 0xFF can be selected. To set this feature: Determine the desired character or value. A setting of 0xFF indicates the Enable Character is not used (not available). 1. Determine the desired character or value. 2. Use the ASCII Chart on the inside back cover of this manual to find the hex equivalent for the desired character/value. 3.
USB Keyboard Interface USB Keyboard Interface Intercode Delay Specifies the delay between labels transmitted to the host for this interface. The selectable range for this feature is from 0 to 99 seconds. Follow these instructions to set this feature: 1. Determine the desired setting. 2. Pad the number with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc 3. Go to page 26 and scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4.
References Symbologies Set Length Length Control allows you to select either variable length decoding or fixed length decoding for the specified symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set. Set Length 1 This feature specifies one of the barcode lengths for Length Control.
Data Editing 3. Scan the barcode to SELECT LENGTH 2 SETTING for your selected symbology. 4. Scan the appropriate two digits from the keypad in Appendix D, Keypad that represent the length setting which was determined in the steps above. You will hear a two-beep indication after the last character. If you make a mistake, before the last character scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. 5.
References • • • A prefix or suffix may be applied only to a specified symbology (reference "1D Code Selection" starting on page 57) or across all symbologies (set via the Global features in this chapter). You can add any character from the ASCII Chart (from 00-FF) on the inside back cover of this manual as a prefix, suffix or Label ID. Enter prefixes and suffixes in the order in which you want them to appear on the output.
Data Editing Global AIM ID This feature enables/disables addition of AIM IDs for all symbology types. AIM label identifiers (as opposed to custom characters you select yourself as with label identifiers) can be included with scanned barcode data. AIM label identifiers consist of three characters as follows: • A close brace character (ASCII ‘]’), followed by... • A code character (see the table below), followed by... • A modifier character (the modifier character is symbol dependent).
References Label ID A Label ID is a customizable code of up to three ASCII characters (each can be one of hex 0x01-0xFF), used to identify a barcode (symbology) type. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled. This feature provides options for configuring custom Label IDs as a pre-loaded set (see "Label ID: Pre-loaded Sets" below) or individually per symbology (see "Label ID: Set Individually Per Symbology" on page 195).
Data Editing USA Label ID set Symbology EU Label ID set Default Character Default ASCII Default Character Default ASCII DATABAR 14 R4 523400 u 750000 DATABAR 14 COMPOSITE R4 523400 c 523400 DATABAR EXPANDED RX 525800 t 740000 DATABAR EXPANDED COMPOSITE RX 525800 d 525800 DATABAR LIMITED RL 524C00 v 760000 DATABAR LIMITED COMPOSITE RL 524C00 i 524C00 DATA MATRIX Dm 446D00 w 770000 EAN128 000000 k 6B0000 EAN128 COMPOSITE 000000 $E 244500 EAN13 F 460000 B 42
References USA Label ID set Symbology EU Label ID set Default Character Default ASCII Default Character Default ASCII MICRO QR $Q 245100 $Q 245100 MICRO PDF mP 6D5000 8 380000 MSI @ 400000 Z 5A0000 PDF417 P 500000 r 720000 PLESSEY a 610000 a 610000 POSTAL AUSTRALIAN $K 244B00 $K 244B00 POSTAL IMB $V 245600 $V 245600 POSTAL JAPANESE $R 245200 $R 245200 POSTAL KIX $U 245500 $U 245500 POSTAL PLANET $W 245700 $W 245700 POSTAL PORTUGAL $P 245000 $P 2450
Data Editing Label ID: Set Individually Per Symbology To configure a Label ID individually for a single symbology: 1. Go to page 34 and scan the ENTER/EXIT barcode. 2. Select Label ID position as either BEFORE (Enable as Prefix) or AFTER (Enable as suffix) by scanning the appropriate barcode in the section "Label ID Control" on page 34. Reference Figure 4 for Label ID positioning options if multiple identification features are enabled. 3.
References Table 34. Label ID Examples STEP ACTION EXAMPLES 1. Scan the ENTER/EXIT barcode (Scanner enters Programming Mode) 2. Determine placement of the Label ID characters BEFORE or AFTER with regard to scanned Enable as Prefix data using "Label ID Control" starting on page 34 Enable as Suffix Enable as Prefix Enable as Suffix 3.
Data Editing Character Conversion Character conversion is an eight byte configuration item. The eight bytes are 4 character pairs represented in hexadecimal ASCII values. The first character in the pair is the character that will be converted. The second character in the pair is the character to convert to. If the character to convert in a pair is FF, then no conversion is done.
References Reading Parameters Good Read LED Duration This feature specifies the amount of time that the Good Read LED remains on following a good read. The good read LED on time can be set within a range of 100 milliseconds to 25,550 milliseconds (0.1 to 25.5 seconds) in 100ms increments. Follow these instructions to set this feature: 1. Determine the desired setting in milliseconds. A setting of 0 means that the good read LED stays on until the next time the trigger is pulled. 2.
Scanning Features Scanning Features Operating Mode The scanner can operate in two scanning (read) modes. In addition, the illumination can be programmed for several different operations states (off*, dim or on) while the read phase is not active. Automatic. Scanning is continually on. Automatic (Object Sense)*. Scanning is turned on automatically when an item is placed in reader’s field of view (default).
References Aiming Duration Time Specifies the frame of time the aiming pointer remains on after decoding a label, when in trigger single mode. The range for this setting is from 1 to 255 seconds in 1-second increments. Follow these instructions to set this feature: 1. Determine the desired setting. 2. Pad the result with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20 = 020, etc. 3. Go to page 53 and scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4.
Scanning Features Multiple Labels Ordering by Code Symbology This feature Specifies the transmission ordering by symbology type, when Multiple Labels per Frame is enabled.Up to six symbologies can be selected. Zeroes must be added to pad the string to 12 characters if not using all six symbologies. The labels are ordered first as specified in the output mask.
References Table 39.
Appendix A Technical Specifications The following table contains specifications for contains Physical and Performance Characteristics, User Environment and Regulatory information. Table 40. Technical Specifications Item Description Physical Characteristics Color Black Height 2.10”/53.4 mm Dimensions Length 3.07”/78 mm Width 2.5”/63.5 mm Positional Adjustments Weight 10,000 cycles Approximately 6.1 ounces /172 g Electrical Characteristics Voltage & Current Idle/Standby (typical) = 98ma @ 5.
Item Description Minimum Element Width 4 mil (1D Linear and HD) 5 mil (PDF-417) 7 mil (DataMatrix) Print Contrast Minimum 25% minimum reflectance Field of View 40° Hx26° V Depth of Field (Typical) a Symbology Standard Range (SR) 5mil: 1.8" - 7.0" (4.7 - 17.7cm) Code 39 10mil: 0.7" - 13.1" (1.7 - 33.2cm) 20mil: 0.4" - 19.4" (1.1 - 49.2cm) EAN 13mil: 1.0" - 16.5" (2.5 - 41.9cm) 7.5mil: 1.1 - 10.8" (2.8 - 27.3cm) 6.6mil: 1.3" - 6.0" (3.3 - 15.4cm) PDF 417 10mil: 0.9 - 9.4" (2.2 - 23.
Table 41.
Item Interfaces Supported Description USB Com Std., USB Keyboard, USB (see Configuring the Interface on page 9 for; a listing of available interface options). User Environment Operating Temperature 50° to 104° F (10 to 40° C) Storage Temperature Humidity Drop Specifications -22° to 149° F (-30° to 65° C) Operating 20% to 85% Non-operating 5% to 90% relative humidity, non-condensing at ambient) Scanner withstands drops from 0.
LED and Beeper Indications The scanner’s beeper sounds and its LED illuminates to indicate various functions or errors on the scanner. An optional “Green Spot” also performs useful functions. The tables below list these indications. One exception to the behaviors listed in the tables is that the scanner’s functions are programmable, and may or may not be turned on. For example, certain indications such as the power-up beep can be disabled using programming barcode labels. Table 42.
Table 43. Programming Mode Indications Programming Mode - The following indications ONLY occur when the scanner is in Programming Mode. INDICATION Label Programming Mode Entry DESCRIPTION A valid programming label has been scanned. LED BEEPER The Indicator LED blinks continuously Scanner sounds four low frequency beeps. Scanner sounds three times at lowest frequency & current volume. Label Programming Mode Rejection of Label A label has been rejected.
Appendix B Standard Defaults The most common configuration settings are listed in the “Default” column of the table below. Page references are also provided for feature descriptions and programming barcodes for each parameter. A column has also been provided for recording of your preferred default settings for these same configurable features. Table 44.
Parameter Page Default USB Keyboard Speed - - - - - - - - - - - - - - - - - - - 27 1 ms USB Keyboard Numeric Keypad - - - - - - - - - - - 28 Standard Keys Your Setting DATA FORMAT Global Prefix/Suffix - - - - - - - - - - - - - - - - - - - - 30 No Global Prefix Global Suffix = 0x0D (CR) Global AIM ID - - - - - - - - - - - - - - - - - - - - - - - 30 Disable Set AIM ID Individually for GS1-128 - - - - - - - - 33 Disable Label ID Control - - - - - - - - - - - - - - - - - - - - - - 34 Prefix Case
Parameter Page Default Decode Negative Image - - - - - - - - - - - - - - - - - - 54 Disable Your Setting Multiple Label Reading Multiple Labels Reading in a Volume - - - - - - - - - 55 Disable Multiple Labels per Frame - - - - - - - - - - - - - - - - 55 Disable Multiple Labels Ordering by Code Symbology - - 56 Random Order Multiple Labels Ordering by Code Length - - - - - 56 Disable CODE SELECTION - 1D SYMBOLOGIES Code EAN/UPC Coupon Control - - - - - - - - - - - - - - - - - - - - - - - 59 En
Parameter Page Default EAN-13 ISBN Conversion - - - - - - - - - - - - - - - - 67 Disable EAN-13 2D Component - - - - - - - - - - - - - - - - - 68 2D Component Not Required Your Setting ISSN ISSN Enable/Disable - - - - - - - - - - - - - - - - - - - 68 Disable EAN 8 EAN 8 Enable/Disable - - - - - - - - - - - - - - - - - - 69 Enable EAN 8 Check Character Transmission - - - - - - - - 69 Send Expand EAN 8 to EAN 13 - - - - - - - - - - - - - - - - 70 Disable EAN 8 2D Component - - - - - - - - - -
Parameter Page Default Code 32 Check Character Transmission - - - - - - - 86 Don’t Send Code 32 Start/Stop Character Transmission - - - - - 87 Don’t Transmit Your Setting Code 39 CIP (French Pharmaceutical Code) Code 39 CIP Enable/Disable - - - - - - - - - - - - - - 87 Disable Special Codes Code 39 LaPoste Enable/Disable - - - - - - - - - - - - 88 Disable Code 128 Code 128 Enable/Disable - - - - - - - - - - - - - - - - - 88 Enable Expand Code 128 to Code 39 - - - - - - - - - - - - - - 89 Don’
Parameter Page Default I 2 of 5 Set Length 1 - - - - - - - - - - - - - - - - - - - 101 6 I 2 of 5 Set Length 2 - - - - - - - - - - - - - - - - - - - 102 50 Your Setting Interleaved 2 of 5 CIP HR Follett 2 of 5 Follett 2 of 5 Enable/Disable - - - - - - - - - - - - - 103 Disable Standard 2 of 5 Standard 2 of 5 Enable/Disable - - - - - - - - - - - - 104 Disable Standard 2 of 5 Check Character Calculation - - 104 Disable Standard 2 of 5 Check Character Transmission - 105 Send Standard 2 of 5 Len
Parameter Page Default Codabar Quiet Zones - - - - - - - - - - - - - - - - - - 116 Small Quiet Zones on two sides Codabar Length Control - - - - - - - - - - - - - - - - 116 Variable Codabar Set Length 1 - - - - - - - - - - - - - - - - - - 117 3 Codabar Set Length 2 - - - - - - - - - - - - - - - - - - 118 50 ABC Codabar - - - - - - - - - - - - - - - - - - - - - - - 119 Disable Your Setting ABC Codabar ABC Codabar Enable/Disable - - - - - - - - - - - - - 119 Disable ABC Codabar Concatenation M
Parameter Page Default GS1 DataBar™ Limited Enable/Disable - - - - - 132 Disable GS1 DataBar™ Limited GS1-128 Emulation - - 132 Disable GS1 DataBar™ Limited 2D Component - - - - - 133 2D component not required Your Setting GS1 DataBar™ Limited Code 93 Code 93 Enable/Disable - - - - - - - - - - - - - - - - 133 Enable Code 93 Check Character Calculation - - - - - - - 134 Enable Check C and K Code 93 Check Character Transmission - - - - - - 134 Enable Code 93 Length Control - - - - - - - - - -
Parameter Page Default 2D Structured Append - - - - - - - - - - - - - - - - - - 149 Disable 2D Normal/Inverse Symbol Control - - - - - - - - - 149 Normal Aztec Code Enable / Disable - - - - - - - - - - - - - 150 Disable Aztec Code Length Control - - - - - - - - - - - - - - 150 Enable Aztec Code Length Control - - - - - - - - - - - - - - 150 Variable Aztec Code Set Length 1 - - - - - - - - - - - - - - - - 151 1 China Sensible Code Enable / Disable - - - - - - - 153 Disable China Sensible Cod
Parameter Page Default QR Code Length Control - - - - - - - - - - - - - - - - 168 Variable QR Code Set Length 1 - - - - - - - - - - - - - - - - - 169 1 QR Code Set Length 2 - - - - - - - - - - - - - - - - - 170 7,089 Micro QR Code Enable/Disable 171 Disable Micro QR Code Length Control - - - - - - - - - - - 171 Variable Micro QR Code Set Length 1 - - - - - - - - - - - - - 172 0001 Micro QR Code Set Length 2 - - - - - - - - - - - - - 173 0035 UCC Composite Enable / Disable - - - - - - - - -
Appendix C Sample Barcodes The sample barcodes in this appendix are typical representations for their symbology types.
Sample Barcodes — continued Code 32 Codabar 13579 Code 93 Code 11 123456789 220 HP Retail Integrated Barcode Scanner
GS1 DataBar™ (RSS) GS1 DataBar™ variants must be enabled to read the barcodes below (see GS1 Data- Bar™ Omnidirectional on page 126).
2D Barcodes Aztec Datamatrix China Sensible Code MaxiCode PDF 417 Micro PDF 417 ABCabc BV17453 QR Code Micro QR Code 123456 35900G9 UCC Composite 222 HP Retail Integrated Barcode Scanner
Appendix D Keypad Use the barcodes in this appendix to enter numbers as you would select digits/characters from a keypad.
224 A B C D E F HP Retail Integrated Barcode Scanner
Appendix E Scancode Tables Control Character Emulation Control character emulation selects from different scancode tables as listed in this appendix. Each of the control character sets below are detailed by interface type in the tables. These apply to USB Keyboard platforms. Control Character 00 : Characters from 00 to 0x1F are sent as control character Ctrl+Keys, special keys are located from 0x80 to 0xA1.
Interface Type USB-Keyboard Table 45.
Interface Type USB-Keyboard — cont. Table 46. Scancode Set When Control Character is 02 0x x0 x1 x2 x3 x4 x5 X6 x7 x8 x9 xA xB Ar↓ Ar↑ Al↓ Al ↑ Cl ↓ Cl ↑ Cr ↓ Cr ↑ BS Tab S+ Tab Home F1 F2 F3 F4 F5 ESC F7 xD xE xF Enter Ins Pg Up 1x Pg Dwn 2x Space ! “ # $ % & ‘ ( ) * + , - .
Interface type USB-Keyboard Alt Mode Table 47.
Interface type USB-Keyboard Alt Mode — cont. Table 48.
Microsoft Windows Codepage 1252 Windows-1252 is a character encoding of the Latin alphabet, used by default in the legacy components of Microsoft Windows in English and some other Western languages.
Appendix F Quick Setup Use the barcodes in this appendix to perform quick setup procedures for common tasks. Scan the following barcode to set the scanner back to the factory defaults: $P,HA00,P(CR) Restore Custom Default Configuration Scanning the "Set All Defaults" barcode does not change the interface type. Scan the following barcode (USB HID Keyboard Emulation) in order to put the HP RPOS Integrated Scanner into the default mode.
Carriage Return Scan the following barcode to set the scanner back to the factory defaults: $P,HA00,P(CR) Restore Custom Default Configuration Scanning the "Set All Defaults" barcode does not change the interface type.
Tab Scan the following barcode to set the scanner back to the factory defaults: $P,HA00,P(CR) Restore Custom Default Configuration Scanning the "Set All Defaults" barcode does not change the interface type.
Volume Scan the following barcode to set the scanner back to the factory defaults: $P,HA00,P(CR) Restore Custom Default Configuration Scanning the "Set All Defaults" barcode does not change the interface type.
ASCII Chart ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No. NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F SP ! “ # $ % & ’ ( ) * + , .
NOTES
