Programming Reference Guide

ManualsBrandsHP ManualsDesktopsHP rp5800 Retail System

HP Wireless Barcode Scanner

Summary of content (290 pages)

PAGE 1
HP Wireless Barcode Scanner Programming Reference Guide
PAGE 2
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
PAGE 3
Table of Contents INTRODUCTION ................................................................................................................................................................................ 1 About this Manual .......................................................................................................................................................................................... 1 Overview ......................................................................................
PAGE 4
Set AIM ID Individually for GS1-128 ...............................................................................................................................................................................................35 Label ID .......................................................................................................................................................................................................... 36 Label ID: Pre-Loaded Sets .........................................
PAGE 5
EAN 13 Enable/Disable .................................................................................................................................................................................................74 EAN 13 Check Character Transmission ...................................................................................................................................................................74 EAN-13 Flag 1 Character ....................................................................
PAGE 6
ISBT 128 Advanced Concatenation Options ...................................................................................................................................................... 107 INTERLEAVED 2 OF 5 (I 2 OF 5) .................................................................................................................................................108 I 2 of 5 Enable/Disable ..................................................................................................................
PAGE 7
GS1 DataBar™ Expanded Set Length 2 ................................................................................................................................................................. 142 GS1 DATABAR™ LIMITED ..........................................................................................................................................................143 GS1 DataBar™ Limited Enable/Disable ................................................................................................
PAGE 8
Micro PDF417 Length Control ...................................................................................................................................................................................................... 178 Micro PDF417 Set Length 1 ...................................................................................................................................................................................... 178 Micro PDF417 Set Length 2 ..........................................
PAGE 9
Set Length ............................................................................................................................................................................................................................................ 219 Data Editing ................................................................................................................................................................................................220 Global Prefix/Suffix ..............................
PAGE 10
NOTES viii HP Wireless Barcode Scanner
PAGE 11
Chapter 1 Introduction About this Manual This Programming Reference Guide (PRG) is provided for users seeking advanced technical information, including connection, programming, maintenance and specifications. The HP Wireless Barcode Scanner User Guide and other publications associated with this product are available for free download from the HP website. This manual covers the HP Wireless Barcode Scanner.
PAGE 12
Introduction References Manual Conventions The following conventions are used in this document: The symbols listed below are used in this manual to notify the user of key issues or procedures that must be observed when using the scanner: Notes contain information necessary for properly diagnosing, repairing and operating the scanner. The CAUTION symbol advises you of actions that could damage equipment or property.
PAGE 13
About the Scanner Introduction About the Scanner Typically, units are factory-programmed for the appropriate terminal and communications settings. If modification is needed for any programmable settings, custom configuration can be accomplished by scanning the programming barcodes within this guide. Programming can alternatively be performed using the HP Configuration application that can be installed from the CD included with the scanner.
PAGE 14
Introduction Programming the Scanner NOTES 4 HP Wireless Barcode Scanner
PAGE 15
Chapter 2 Setup Unpacking Check carefully to ensure the scanner and any accessories ordered are present and undamaged. If any damage occurred during shipment, contact HP Technical Support. Information is shown on page 2. KEEP THE PACKAGING. Should the unit ever require service, it should be returned in its original shipping container. Setting Up the Scanner Follow the steps provided in this section to connect and get your scanner up and communicating with its host. 1.
PAGE 16
Setup Setting Up the Scanner Connecting the Base when Security Pin is Enabled When connecting the Base to a system that has a custom Security Pin enabled, follow the steps below in the order shown: 1. Power down the host system. 2. Connect the appropriate interface cable into the Base. 3. Place the scanner in the Base. 4. Power up the host. The scanner will link to the Base 5.
PAGE 17
Setting Up the Scanner Setup Linking the BT Scanner to a PC The scanner can optionally be linked to a Bluetooth-enabled PC with the serial port profile, in either server mode or client mode. Linking to a PC in Server Mode (BT Slave Mode) To link a BT scanner in server mode to a Bluetooth-enabled PC, follow these steps: 1. Install any drivers provided with the Bluetooth adapter. 2. Scan the barcode below to make the scanner visible to the host computer. ³ L n k S v Link to a PC in Server Mode 3.
PAGE 18
Setup Interface Selection Interface Selection Upon completing the physical connection between the scanner and its host, proceed to Table 1 below o select the interface type (if needed to change for specific application). Scan the appropriate barcode in that section to configure your system’s correct interface type. The scanner supports USB interface with types HID Keyboard and COM.
PAGE 19
Customizing Configuration Settings Setup Customizing Configuration Settings Configure Interface Settings If after scanning the interface barcode from the previous table, your installation requires you to select options to further customize your scanner, turn to "Configuration Parameters" starting on page 11. Global Interface Features See "Global Interface Features" on page 13 for settings configurable by all interface types.
PAGE 20
Setup Customizing Configuration Settings Resetting the Product Configuration to Defaults Restore Custom Defaults If you aren’t sure what programming options are in your imager, or you’ve changed some options and want to restore the Custom Default Configuration that may have been saved in the scanner, scan the Restore Custom Default Configuration barcode below. This will restore the custom configuration for the currently active interface. Custom defaults are based on the interface type.
PAGE 21
Chapter 3 Configuration Using Barcodes This and following sections provide programming barcodes to configure your scanner by changing the default settings. For details about additional methods of programming, see "Configuration Methods" on page 3. You must first enable your scanner to read barcodes in order to use this section. If you have not done this, go to Setup, starting on page 5 and complete the appropriate procedure.
PAGE 22
Enter/Exit Programming Mode To program features: 1. Scan the ENTER/EXIT PROGRAMMING barcode, available at the top of each programming page, when applicable. 2. Scan the barcode to set the desired programming feature. You may need to cover unused barcodes on the page, and possibly the facing page, to ensure that the scanner reads only the barcode you intend to scan. 3. If additional input parameters are needed, go to Appendix D, Keypad, and scan the appropriate characters from the keypad.
PAGE 23
Enter/Exit Programming Mode GLOBAL INTERFACE FEATURES The following interface features are configurable by all interface types. Host Commands — Obey/Ignore This option specifies whether the scanner will obey or ignore host commands. When set to ignore, the scanner will ignore all host commands except for those necessary for: • service mode • flash programming mode • keeping the interface active • transmission of labels.
PAGE 24
Enter/Exit Programming Mode NOTES 14 HP Wireless Barcode Scanner
PAGE 25
USB-COM INTERFACE INTERCHARACTER DELAY on page 16 BEEP ON ASCII BEL on page 16 BEEP ON NOT ON FILE on page 17 ACK NAK OPTIONS on page 18 ACK CHARACTER on page 19 NAK CHARACTER on page 19 ACK NAK TIMEOUT VALUE on page 20 ACK NAK RETRY COUNT on page 20 ACK NAK ERROR HANDLING on page 21 INDICATE TRANSMISSION FAILURE on page 21 DISABLE CHARACTER on page 22 ENABLE CHARACTER on page 22 The programming barcodes in this chapter allow modifications to the standard USB-Com interfaces.
PAGE 26
Enter/Exit Programming Mode Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. See page 217 for more information.
PAGE 27
Enter/Exit Programming Mode Beep On Not on File This option enables/disables the action of the reader to sound a three beep sequence upon receiving a Not-OnFile (NOF) host command.
PAGE 28
Enter/Exit Programming Mode ACK NAK Options This enables/disables the ability of the reader to support the ACK/NAK protocol. See page 211 for more information.
PAGE 29
Enter/Exit Programming Mode ACK Character This setting specifies an ASCII character or hex value to be used as the ACK character. ASCII characters or any hex value from 0 to 0xFF can be selected. See page 211 for more information. Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of this character.
PAGE 30
Enter/Exit Programming Mode ACK NAK Timeout Value This option specifies the amount of time the reader waits for an ACK character from the host following label transmission. The selectable timeout range is 200 milliseconds to 15,000ms (15 seconds) in 200ms increments. A selection of 0 disables the timeout. See page 212 for more information on setting this feature.
PAGE 31
Enter/Exit Programming Mode ACK NAK Error Handling This feature specifies the method the reader uses to handle receive errors detected while waiting for an ACK character from the host.
PAGE 32
Enter/Exit Programming Mode Disable Character Specifies the value of the host command used to disable the reader. ASCII characters or any hex value from 0 to 0xFF can be selected. Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of this character. See page 215 for more information on setting this feature.
PAGE 33
USB KEYBOARD SETTINGS COUNTRY MODE on page 24 SEND CONTROL CHARACTERS on page 27 INTERCODE DELAY on page 28 USB KEYBOARD SPEED on page 29 USB KEYBOARD NUMERIC KEYPAD on page 30 Use the programming barcodes in this chapter to select options for USB Keyboard Interface. Reference Appendix B, Standard Defaults for a listing of standard factory settings. Information about control character emulation which applies to keyboard interfaces is listed in Appendix E, Scancode Tables.
PAGE 34
Enter/Exit Programming Mode Country Mode This feature specifies the country/language supported by the USB keyboard. $CKBCO00(CR) DEFAULT Country Mode = U.S. $CKBCO01(CR) Country Mode = Belgium $CKBCO02(CR) Country Mode = Britain $CKBCO11(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Croatia $CKBCO0E(CR) Supports only the interfaces listed in the Country Mode feature description.
PAGE 35
Enter/Exit Programming Mode Country Mode (continued) Supports only the interfaces listed in the Country Mode feature description. $CKBCO13(CR) Country Mode = French Canadian $CKBCO05(CR) Country Mode = Germany $CKBCO0D(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Hungary $CKBCO06(CR) Country Mode = Italy $CKBCO0C(CR) Supports only the interfaces listed in the Country Mode feature description.
PAGE 36
Enter/Exit Programming Mode Country Mode (continued) $CKBCO12(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Poland Supports only the interfaces listed in the Country Mode feature description. $CKBCO08(CR) Country Mode = Portugal $CKBCO10(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Romania Supports only the interfaces listed in the Country Mode feature description.
PAGE 37
Enter/Exit Programming Mode Send Control Characters This feature specifies how the scanner transmits ASCII control characters to the host. Reference Appendix E, Scancode Tables for more information about control characters. Options are as follows: Control Character 00 : Characters from 00 to 0x1F are sent as control character Ctrl+Keys, special keys are located from 0x80 to 0xA1.
PAGE 38
Enter/Exit Programming Mode Intercode Delay Specifies the delay between labels transmitted to the host for this interface. The selectable range for this feature is from 0 to 99 seconds. See page 218 in “References” for detailed information and examples for setting this feature. $CKBID Set Intercode Delay Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 39
Enter/Exit Programming Mode USB Keyboard Speed This option specifies the USB poll rate for a USB keyboard.
PAGE 40
Enter/Exit Programming Mode USB Keyboard Speed (continued) $CKBSP07(CR) USB Keyboard Speed = 7ms $CKBSP08(CR) USB Keyboard Speed = 8ms $CKBSP09(CR) USB Keyboard Speed = 9ms $CKBSP0A(CR) USB Keyboard Speed = 10ms USB Keyboard Numeric Keypad This option Controls whether numeric characters will be sent using standard keys or the numeric keypad.
PAGE 41
DATA FORMAT GLOBAL PREFIX/SUFFIX starting on page 32 GLOBAL AIM ID starting on page 33 LABEL ID starting on page 36 •Label ID: Pre-Loaded Sets •Individually Set Label ID •Label ID Control •Label ID Symbology Selection − •Label ID Symbology Selection − 1D Symbologies 2D Symbologies CASE CONVERSION starting on page 43 CHARACTER CONVERSION starting on page 44 The features in this chapter can be used to build specific user-defined data into a message string.
PAGE 42
Enter/Exit Programming Mode Global Prefix/Suffix Global Prefix/Suffix This option sets up to 20 characters each from the set of ASCII characters or any hex value from 00 to FF. The characters may be added as a prefix (in a position before the barcode data, also called a header) and/or as a suffix (in a position following the barcode data, also called a footer). See page 221 for more detailed instructions on setting this feature.
PAGE 43
Global AIM ID Enter/Exit Programming Mode Global AIM ID This feature enables/disables addition of AIM IDs for all symbology types. AIM label identifiers (as opposed to custom characters you select yourself as with label identifiers) can be included with scanned barcode data. See Table 2 on page 3-33 for a listing of AIM IDs. AIM label identifiers consist of three characters as follows: • A close brace character (ASCII ‘]’), followed by...
PAGE 44
Enter/Exit Programming Mode DATABAR EXPANDED COMPOSITE DATABAR LIMITED DATABAR LIMITED COMPOSITE DATA MATRIX EAN128 EAN128 COMPOSITE EAN13 EAN13 P2 EAN13 P5 EAN13 COMPOSITE EAN8 EAN8 P2 EAN8 P5 EAN8 COMPOSITE FOLLET 2OF5 I2OF5 IATA INDUSTRIAL 2OF5 INDUSTRIAL 2OF5 ISBN ISBT128 CONCAT ISSN MAXICODE MICRO QR MICRO PDF MSI PDF417 PLESSEY POSTAL AUSTRALIAN POSTAL IMB POSTAL JAPANESE POSTAL KIX POSTAL PLANET POSTAL PORTUGAL POSTAL POSTNET BB POSTAL ROYAL MAIL POSTAL SWEDISH POSTNET QR CODE S25 TRIOPTIC UPCA UPCA
PAGE 45
Global AIM ID Enter/Exit Programming Mode Set AIM ID Individually for GS1-128 This feature configures a Label ID individually for the GS1-128 symbology and the programming for this works the same way as Label ID. See Label ID: Set Individually Per Symbology, starting on page 226 for detailed instructions on setting this feature.
PAGE 46
Enter/Exit Programming Mode Label ID Label ID A Label ID is a customizable code of up to three ASCII characters (convert to Hex using the ASCII Chart on the inside back cover of this manual), used to identify a barcode symbology type. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled. This feature provides options for configuring custom Label IDs or individually per symbology (see "Individually Set Label ID" on page 37).
PAGE 47
Label ID Enter/Exit Programming Mode Individually Set Label ID This feature configures a Label ID individually for a single symbology. To set, first define whether you want it as a prefix or suffix by scanning a label below. Then turn to Label ID Symbology Selection − 1D Symbologies, starting on page 38 to select the symbology you want to set, followed by up to 3 characters from the ASCII Chart at the back of this manual.
PAGE 48
Enter/Exit Programming Mode Label ID Label ID Symbology Selection − 1D Symbologies This option selects the symbology for which a Label ID is to be configured. See "Label ID" on page 36 or page 226 in “References” for more detailed instructions. If less than the expected string of 3 characters are selected, scan the ENTER/ EXIT barcode twice to accept the selection and exit Programming Mode.
PAGE 49
Label ID Enter/Exit Programming Mode Label ID Symbology Selection − 1D Symbologies (continued) $CCCID Set Code 39 CIP Label ID Character(s) $C8BID Set EAN 8 Label ID Character(s) $C8MID Set EAN 8 Composite Label ID Character(s) $C82ID Set EAN 8 P2 Label ID Character(s) $C85ID Set EAN 8 P5 Label ID Character(s) $CF2ID Set Follett 2 of 5 Label ID Character(s) $C4BID Set GS1 DataBar 14 Label ID Character(s) $C4CID Set GS1 DataBar 14 Composite Label ID Character(s) Programming Reference Guide $C35
PAGE 50
Enter/Exit Programming Mode Label ID Label ID Symbology Selection − 1D Symbologies (continued) $CXBID Set GS1 DataBar Expanded Label ID Character(s) $CIAID Set IATA Industrial 2 of 5 Label ID Character(s) $CPMID Set IMB Postal Code Label ID Character(s) $CU2ID Set Industrial 2 of 5 Label ID Character(s) $CI2ID Set Interleaved 2 of 5 Label ID Character(s) $CISID Set ISBN Label ID Character(s) $CINID Set ISSN Label ID Character(s) $CPJID Set Japan Postal Code Label ID Character(s) 40 $CGBID Set
PAGE 51
Label ID Enter/Exit Programming Mode Label ID Symbology Selection − 1D Symbologies (continued) $CPZID Set PZN Code Label ID Character(s) $CPBID Set Postnet BB Label ID Character(s) $CPRID $CAMID Set Royal Postal Code Label ID Character(s) Set UPC-A Composite Label ID Character(s) $CS2ID $CA2ID Set Standard 2 of 5 Label ID Character(s) $CPSID Set Swedish Postal Code Label ID Character(s) $CCTID Set Trioptic Code Label ID Character(s) $CABID Set UPC-A Label ID Character(s) Programming Referenc
PAGE 52
Enter/Exit Programming Mode Label ID Label ID Symbology Selection − 2D Symbologies $CAZID Set Aztec Label ID Character(s) $CCSID Set China Sensible Label ID Character(s) $CDMID Set Data Matrix Label ID Character(s) $CMQID Set Micro QR Label ID Character(s) 42 $CMXID Set Maxicode Label ID Character(s) $CP4ID Set PDF 417 Label ID Character(s) $CMIID Set Micro PDF 417 Label ID Character(s) $CQRID Set QR Code Label ID Character(s) HP Wireless Barcode Scanner
PAGE 53
Label ID Enter/Exit Programming Mode Advanced Formatting: User Label Edit Advanced formatting is available to create user label edit scripts. See the HP Configuration application or contact Technical Support. Case Conversion This feature allows conversion of the case of all alphabetic characters to upper or lower case. Case conversion affects ONLY scanned barcode data, and does not affect Label ID, Prefix, Suffix, or other appended data.
PAGE 54
Enter/Exit Programming Mode Label ID Character Conversion Character conversion is an eight byte configuration item. The eight bytes are 4 character pairs represented in hexadecimal ASCII values. The first character in the pair is the character that will be converted. The second character in the pair is the character to convert to. If the character to convert in a pair is FF, then no conversion is done.
PAGE 55
READING PARAMETERS DOUBLE READ TIMEOUT starting on page 46 LED AND BEEPER INDICATORS starting on page 48 •Power On Alert •Good Read: When to Indicate •Good Read Beep Type •Good Read Beep Frequency •Good Read Beep Length •Good Read Beep Volume •Good Read LED Duration SCANNING FEATURES starting on page 53 •Scan Mode •Stand Mode Indication •Stand Operation •Pick Mode •Stand Mode Sensitivity •Stand Mode Illumination Off Time •Scanning Active Time •Stand Illumination Control •Flash On Time •Flash Off Time •Aimi
PAGE 56
Enter/Exit Programming Mode Double Read Timeout Double Read Timeout prevents a double read of the same label by setting the minimum time allowed between reads of labels of the same symbology and data. If the unit reads a label and sees the same label again within the specified timeout, the second read is ignored. Double Read Timeout does not apply to scan modes that require a trigger pull for each label read. $CSNDR0A(CR) Double Read Timeout = 0.1 Second $CSNDR14(CR) Double Read Timeout = 0.
PAGE 57
Enter/Exit Programming Mode Double Read Timeout (continued) $CSNDR50(CR) Double Read Timeout = 0.8 Second $CSNDR5A(CR) Double Read Timeout = 0.
PAGE 58
Enter/Exit Programming Mode LED AND BEEPER INDICATORS Power On Alert Disables or enables the indication (from the Beeper) that the scanner is receiving power. $CBPPU00(CR) Power On Alert = Disable (No Audible Indication) $CBPPU01(CR) DEFAULT Power On Alert = Power-up Beep Good Read: When to Indicate This feature specifies when the scanner will provide indication (beep and/or flash its green LED) upon successfully reading a barcode.
PAGE 59
Enter/Exit Programming Mode Good Read Beep Type Specifies whether the good read beep has a mono or bitonal beep sound. $CBPTY00(CR) DEFAULT Good Read Beep Type = Mono $CBPTY01(CR) Good Read Beep Type = Bitonal Good Read Beep Frequency Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.
PAGE 60
Enter/Exit Programming Mode Good Read Beep Length $CBPLE06(CR) Good Read Beep Length = 60 msec $CBPLE08(CR) DEFAULT Good Read Beep Length = 80 msec $CBPLE0A(CR) Good Read Beep Length = 100 msec $CBPLE0C(CR) Good Read Beep Length = 120 msec $CBPLE0E(CR) Good Read Beep Length = 140 msec $CBPLE10(CR) Good Read Beep Length = 160 msec $CBPLE12(CR) Good Read Beep Length = 180 msec $CBPLE14(CR) Good Read Beep Length = 200 msec 50 HP Wireless Barcode Scanner
PAGE 61
Enter/Exit Programming Mode Good Read Beep Volume Selects the beeper volume (loudness) upon a good read beep. There are three selectable volume levels.
PAGE 62
Enter/Exit Programming Mode Good Read LED Duration This feature specifies the amount of time that the Good Read LED remains on following a good read. The good read LED on time can be set within a range of 100 milliseconds to 25,500 milliseconds (0.1 to 25.5 seconds) in 100ms increments. A setting of 00 keeps the LED on until the next trigger pull. See page 229 in “References” for detailed instructions and examples for setting this feature.
PAGE 63
Enter/Exit Programming Mode SCANNING FEATURES Scan Mode Selects the scanner’s scan operating mode. See page 230 in “References” for descriptions. $CSNRM00(CR) DEFAULT Scan Mode = Trigger Single $CSNRM01(CR) Scan Mode = Trigger Hold Multiple $CSNRM02(CR) Scan Mode = Trigger Pulse Multiple $CSNRM03(CR Scan Mode = Flashing $CSNRM04(CR) Scan Mode = Always On $CSNRM05(CR Scan Mode = Stand Mode Options concerning Stand Mode behavior are available at the following feature, Stand Operation.
PAGE 64
Enter/Exit Programming Mode Stand Mode Indication This operation is useful for indicating when the scanner is in Stand Mode. If enabled, the blue indicator will blink when Stand Mode scanning is active. If scanner detects motion (or removed from base station) and switches out of Stand Mode into Triggered Mode, blinking will stop until Stand Mode is active again.
PAGE 65
Enter/Exit Programming Mode Stand Operation Specifies the behavior of the scanner when stationary in a stand. There are two conditions which cause the scanner to switch to Stand Mode: 1. The scanner is configured to switch to Stand Mode when stationary. 2. The scanner is placed into the cradle of the base station. Below are further options concerning Stand Operation. Ignore Autorecognition. Disables mode switching when the scanner is placed in a stand. Switch to Stand Mode.
PAGE 66
Enter/Exit Programming Mode Pick Mode Specifies the ability of the scanner to decode labels only when they are close to the center of the aiming pattern. This allows the scanner to accurately target labels when they are placed close together, such as on a pick sheet. This feature is not compatible with Multiple Labels Reading in a Volume. $CSNPM00(CR) DEFAULT Pick Mode = Disable $CSNPM01(CR) Pick Mode = Enable Stand Mode Sensitivity Sets the sensitivity level for stand mode wakeup.
PAGE 67
Enter/Exit Programming Mode Stand Mode Illumination Off Time Specifies the amount of time scanner illumination stays off after pulling the trigger when in Stand Mode. The configurable range is 01 to 32 by 01 in increments of 500ms (500ms to 16 seconds). See page 231 in “References” for a description of this feature.
PAGE 68
Enter/Exit Programming Mode Stand Illumination Control Controls the illumination status while the reading mode is stand mode and the scanner is attempting to detect objects. $CSMIL00(CR) DEFAULT Stand Illumination Control = OFF $CSMIL01(CR) Stand Illumination Control = ON $CSMIL02(CR) Stand Illumination Control = Dim Motion Still Timeout Motion Still Timeout specifies the waiting time after which no motions is detected.
PAGE 69
Enter/Exit Programming Mode DEFAULT 14 = Motion Still Timeout for 2 seconds Flash On Time This feature specifies the ON time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. See page 234 in “References” for detailed information on setting this feature.
PAGE 70
Enter/Exit Programming Mode DEFAULT 06 = Flash is OFF for 600ms Aiming Pointer Enables/disables the aiming pointer for all symbologies. $CTAAP00(CR) Aiming Pointer = Disable $CTAAP01(CR) DEFAULT Aiming Pointer = Enable Aiming Duration Timer Specifies the frame of time the aiming pointer remains on after decoding a label, when in trigger single mode.The range for this setting is from 1 to 255 seconds in 1-second increments. See page 233 in “References” for a description of this feature.
PAGE 71
Enter/Exit Programming Mode Green Spot Duration Specifies the duration of the good read pointer beam after a good read. $CLSSP00(CR) Green Spot Duration = Disable (Green Spot is Off ) $CLSSP01(CR) DEFAULT Green Spot Duration = Short (300 msec) $CLSSP02(CR) Green Spot Duration = Medium (500 msec) $CLSSP03(CR) Green Spot Duration = Long (800 msec) Mobile Phone Mode This mode is useful for scanning barcodes displayed on a mobile phone.
PAGE 72
Enter/Exit Programming Mode Partial Label Reading Control Enable/Disable to ignore partial labels to be read within the boundary of the field of view. IPPL00 Partial Label Reading Control = Disable IPPL01 Partial Label Reading Control = Enable Decode Negative Image Enable/Disable the ability to decode a negative image for all symbologies. When this feature is enabled, you will be unable to read normally-printed labels or programming labels in this manual.
PAGE 73
Enter/Exit Programming Mode MULTIPLE LABEL READING In standard (default) mode, when the scanner’s aiming system is activated (by a trigger pull, motion or other method depending on the mode), it then acquires and processes each image in the area in front of it (the Volume). In this case, the scanner stops processing the image once it decodes a label. If several labels are present in the volume, only the first label encountered is decoded and sent.
PAGE 74
Enter/Exit Programming Mode Multiple Labels Ordering by Code Symbology This feature allows you to specify the order multiple labels are transmitted by symbology type, when Multiple Labels per Frame is enabled. See page 236 in “References” for detailed information on setting this feature. $CSNMS Select Symbologies for Multiple Labels Ordering Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 75
1D SYMBOLOGIES 1D Code Selection The scanner supports the following 1D symbologies (barcode types). See "2D Symbologies" starting on page 159 for 2D barcodes. Symbology-dependent options are included in each chapter.
PAGE 76
Enter/Exit Programming Mode 1D Code Selection 3. If additional input parameters are needed, go to Appendix D, Keypad, and scan the appropriate characters from the keypad. Additional information about many features can be found in the “References” chapter. If you make a mistake before the last character, scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. 4.
PAGE 77
1D Code Selection Enter/Exit Programming Mode CODE EAN/UPC Coupon Control This feature is used to control the scanner’s method of processing coupon labels.
PAGE 78
Enter/Exit Programming Mode 1D Code Selection UPC-A The following options apply to the UPC-A symbology. UPC-A Enable/Disable When disabled, the scanner will not read UPC-A barcodes. $CABEN00(CR) UPC-A = Disable $CABEN01(CR) DEFAULT UPC-A = Enable UPC-A Check Character Transmission Enable this option to transmit the check character along with UPC-A barcode data.
PAGE 79
1D Code Selection Enter/Exit Programming Mode Expand UPC-A to EAN-13 Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. $CAB3B00(CR) DEFAULT UPC-A to EAN-13 = Don’t Expand $CAB3B01(CR) UPC-A to EAN-13 = Expand UPC-A Number System Character Transmission This feature enables/disables transmission of the UPC-A number system character.
PAGE 80
Enter/Exit Programming Mode 1D Code Selection UPC-A 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded. $CAB2D00(CR) DEFAULT EAN-13 2D Component = Disable (2D component not required) $CAB2D01(CR) EAN-13 2D Component = 2D component must be decoded UPC-E The following options apply to the UPC-E symbology. UPC-E Enable/Disable When disabled, the scanner will not read UPC-E barcodes.
PAGE 81
1D Code Selection Enter/Exit Programming Mode UPC-E Check Character Transmission Enable this option to transmit the check character along with UPC-E barcode data. $CEBCT00(CR) UPC-E Check Character Transmission = Don’t Send $CEBCT01(CR) DEFAULT UPC-E Check Character Transmission = Send UPC-E 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label for this symbology is decoded.
PAGE 82
Enter/Exit Programming Mode 1D Code Selection Expand UPC-E to EAN-13 Expands UPC-E data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. $CEB3B00(CR) DEFAULT UPC-E to EAN-13 = Don’t Expand $CEB3B01(CR) UPC-E to EAN-13 = Expand Expand UPC-E to UPC-A Expands UPC-E data to the UPC-A data format.
PAGE 83
1D Code Selection Enter/Exit Programming Mode UPC-E Number System Character Transmission This feature enables/disables transmission of the UPC-E system number character. $CEBNS00(CR) UPC-E Number System Character = Do not transmit $CEBNS01(CR) DEFAULT UPC-E Number System Character = Transmit GTIN FORMATTING This feature enables/disables the ability to convert UPC-E, UPC-A, EAN 8, and EAN 13 labels into the GTIN 14-character format.
PAGE 84
Enter/Exit Programming Mode 1D Code Selection EAN 13 (JAN 13) The following options apply to the EAN 13 (Jan 13) symbology. EAN 13 Enable/Disable When disabled, the scanner will not read EAN 13/JAN 13 barcodes. $C3BEN00(CR) EAN 13 = Disable $C3BEN01(CR) DEFAULT EAN 13 = Enable EAN 13 Check Character Transmission Enable this option to transmit the check character along with EAN 13 barcode data.
PAGE 85
1D Code Selection Enter/Exit Programming Mode EAN-13 Flag 1 Character Enables/disables transmission of an EAN/JAN13 Flag1 character. The Flag 1 character is the first character of the label. $C3BF100(CR) EAN-13 Flag 1 Char= Don’t transmit $C3BF101(CR) DEFAULT EAN-13 Flag 1 Char= Transmit EAN-13 ISBN Conversion This option enables/disables conversion of EAN 13/JAN 13 Bookland labels starting with 978 to ISBN labels.
PAGE 86
Enter/Exit Programming Mode 1D Code Selection EAN-13 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded. $C3B2D00(CR) DEFAULT EAN-13 2D Component = Disable (2D component not required) $C3B2D01(CR) EAN-13 2D Component = 2D component must be decoded ISSN The following options apply to the ISSN symbology. ISSN Enable/Disable Enables/disables conversion of EAN/JAN13 Bookland labels starting with 977 to ISSN labels.
PAGE 87
1D Code Selection Enter/Exit Programming Mode EAN 8 (JAN 8) The following options apply to the EAN 8 (Jan 8) symbology. EAN 8 Enable/Disable When disabled, the scanner will not read EAN 8/JAN 8 barcodes. $C8BEN00(CR) EAN 8 = Disable $C8BEN01(CR) DEFAULT EAN 8 = Enable EAN 8 Check Character Transmission Enable this option to transmit the check character along with EAN 8 barcode data.
PAGE 88
Enter/Exit Programming Mode 1D Code Selection Expand EAN 8 to EAN 13 Enable this option to expand EAN 8/JAN 8 labels to EAN 13/JAN 13. $C8B3B00(CR) DEFAULT Expand EAN 8 to EAN 13 = Disable $C8B3B01(CR) Expand EAN 8 to EAN 13 = Enable EAN 8 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label for this symbology is decoded.
PAGE 89
1D Code Selection Enter/Exit Programming Mode UPC/EAN GLOBAL SETTINGS This section provides configuration settings for UPC-A, UPC-E, EAN 13 and EAN 8 symbologies, and affects all of these unless otherwise marked for each feature description. UPC/EAN Price Weight Check This feature enables/disables calculation and verification of price/weight check digits.
PAGE 90
Enter/Exit Programming Mode 1D Code Selection UPC/EAN Quiet Zones This feature specifies the number of quiet zones for UPC/EAN labels. Quiet zones are blank areas at the ends of a barcode, typically 10 times the width of the narrowest bar or space in the label. The property applies to all EAN-UPC symbologies globally and to the ADDONs.
PAGE 91
1D Code Selection Enter/Exit Programming Mode ADD-ONS Contact Customer Support for advanced programming of optional and conditional add-ons. Optional Add-ons The scanner can be enabled to optionally read the following add-ons (supplementals): If a UPC/EAN base label and an add-on are both decoded, the scanner will transmit the base label and add-on. If a UPC/EAN base label is decoded without an add-on, the base label will be transmitted without an add-on.
PAGE 92
Enter/Exit Programming Mode 1D Code Selection Optional Add-On Timer This option sets the time the scanner will look for an add-on when an add-on fragment has been seen and optional add-ons are enabled. (Also see "Optional GS1-128 Add-On Timer" on page 85.
PAGE 93
1D Code Selection Enter/Exit Programming Mode Optional Add-On Timer (continued) $CADOT06(CR) Optional Add-on Timer = 60ms $CADOT07(CR) DEFAULT Optional Add-on Timer = 70ms $CADOT0A(CR) Optional Add-on Timer = 100ms $CADOT0C(CR) Optional Add-on Timer = 120ms $CADOT0E(CR) Optional Add-on Timer = 140ms $CADOT10(CR) Optional Add-on Timer = 160ms Programming Reference Guide 83
PAGE 94
Enter/Exit Programming Mode 1D Code Selection Optional Add-On Timer (continued) $CADOT12(CR) Optional Add-on Timer = 180ms $CADOT14(CR) Optional Add-on Timer = 200ms $CADOT16(CR) Optional Add-on Timer = 220ms $CADOT18(CR) Optional Add-on Timer = 240ms $CADOT1A(CR) Optional Add-on Timer = 260ms $CADOT1C(CR) Optional Add-on Timer = 280ms $CADOT1E(CR) Optional Add-on Timer = 300ms 84 HP Wireless Barcode Scanner
PAGE 95
1D Code Selection Enter/Exit Programming Mode Optional GS1-128 Add-On Timer This option sets the timer expiration value to read the added part after reading the linear EAN/UPC part. For UPC/EAN add-ons other than those of that type, see "Optional Add-On Timer" on page 82.
PAGE 96
Enter/Exit Programming Mode 1D Code Selection Optional GS1-128 Add-On Timer (continued) $CADUT06(CR) Optional GS1-128 Add-On Timer = 60ms $CADUT07(CR) Optional GS1-128 Add-On Timer = 70ms $CADUT0A(CR) Optional GS1-128 Add-On Timer = 100ms $CADUT0C(CR) Optional GS1-128 Add-On Timer = 120ms $CADUT0E(CR) Optional GS1-128 Add-On Timer = 140ms $CADUT10(CR) Optional GS1-128 Add-On Timer = 160ms — cont.
PAGE 97
1D Code Selection Enter/Exit Programming Mode Optional GS1-128 Add-On Timer (continued) $CADUT12(CR) Optional GS1-128 Add-On Timer = 180ms $CADUT14(CR) Optional GS1-128 Add-On Timer = 200ms $CADUT16(CR) Optional GS1-128 Add-On Timer = 220ms $CADUT18(CR) Optional GS1-128 Add-On Timer = 240ms $CADUT1A(CR) Optional GS1-128 Add-On Timer = 260ms $CADUT1C(CR) Optional GS1-128 Add-On Timer = 280ms $CADUT1E(CR) Optional GS1-128 Add-On Timer = 300ms Programming Reference Guide 87
PAGE 98
Enter/Exit Programming Mode 1D Code Selection CODE 39 The following options apply to the Code 39 symbology. Code 39 Enable/Disable $CC3EN00(CR) Code 39 = Disable $CC3EN01(CR) DEFAULT Code 39 = Enable Code 39 Check Character Calculation Enable this option to enables/disables calculation and verification of an optional Code 39 check character.
PAGE 99
1D Code Selection Enter/Exit Programming Mode Code 39 Check Character Calculation (continued) $CC3CC04(CR) Code 39 Check Character Calculation = Enable Italian Post Check $CC3CC08(CR) Code 39 Check Character Calculation = Enable Daimler Chrysler Check Code 39 Check Character Transmission Enable this option to transmit the check character along with Code 39 barcode data.
PAGE 100
Enter/Exit Programming Mode 1D Code Selection Code 39 Start/Stop Character Transmission Enable this option to enable/disable transmission of Code 39 start and stop characters. $CC3SS00(CR) DEFAULT Code 39 Start/Stop Character Transmission = Don’t Transmit $CC3SS01(CR) Code 39 Start/Stop Character Transmission = Transmit Code 39 Full ASCII Enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters.
PAGE 101
1D Code Selection Enter/Exit Programming Mode Code 39 Quiet Zones This feature specifies the number of quiet zones for Code 39 labels. Quiet zones are blank areas at the ends of a barcode, typically 10 times the width of the narrowest bar or space in the label.
PAGE 102
Enter/Exit Programming Mode 1D Code Selection Code 39 Set Length 1 This feature specifies one of the barcode lengths for Code 39 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 0 to 50 characters. Table 3 provides examples for setting Length 1. See page 219 for detailed instructions on setting this feature. Table 3.
PAGE 103
1D Code Selection Enter/Exit Programming Mode Code 39 Set Length 2 This feature specifies one of the barcode lengths for Code 39 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. Table 4 provides examples for setting Length 2. See page 219 for detailed instructions on setting this feature. Table 4.
PAGE 104
Enter/Exit Programming Mode 1D Code Selection TRIOPTIC CODE The following options apply to the Trioptic symbology. Trioptic Code Enable/Disable $CCTEN00(CR) DEFAULT Trioptic Code = Disable $CCTEN01(CR) Trioptic Code = Enable CODE 32 (ITAL PHARMACEUTICAL CODE) The following options apply to the Code 32 (Italian Pharmaceutical Code) symbology. Code 32 Enable/Disable When disabled, the scanner will not read Code 32 barcodes.
PAGE 105
1D Code Selection Enter/Exit Programming Mode Code 32 Feature Setting Exceptions The following features are set for Code 32 by using these Code 39 settings: "Code 39 Quiet Zones" on page 91 "Code 39 Length Control" on page 91 "Trioptic Code" on page 94 Code 32 Check Char Transmission Enable this option to transmit the check character along with Code 32 barcode data.
PAGE 106
Enter/Exit Programming Mode 1D Code Selection CODE 39 CIP (FRENCH PHARMACEUTICAL) The following options apply to the Code 39 CIP symbology. Code 39 CIP Enable/Disable Enables/Disables ability of the scanner to decode Code 39 CIP labels. $CCCEN00(CR) DEFAULT Code 39 CIP = Disable $CCCEN01(CR) Code 39 CIP = Enable CODE 39 DANISH PPT The following options apply to the Code 39 Danish PPT symbology. Code 39 Danish PPT Enable/Disable Enables/Disables AIM ID for Code 39 Danish PPT Codes.
PAGE 107
1D Code Selection Enter/Exit Programming Mode CODE 39 LAPOSTE The following options apply to the Code 39 LaPoste symbology. Code 39 LaPoste Enable/Disable Enables/disables the ability of the scanner to decode Code39 La Poste labels. $CLPEN00(CR) DEFAULT Code 39 LaPoste = Disable $CLPEN01(CR) Code 39 LaPoste = Enable CODE 39 PZN The following options apply to the Code 39 PZN symbology. Code 39 PZN Enable/Disable Enables/disables the ability of the scanner to decode Code39 PZN labels.
PAGE 108
Enter/Exit Programming Mode 1D Code Selection CODE 128 The following options apply to the Code 128 symbology. Code 128 Enable/Disable When disabled, the scanner will not read Code 128 barcodes. $CC8EN00(CR) Code 128 = Disable $CC8EN01(CR) DEFAULT Code 128 = Enable Expand Code 128 to Code 39 This feature enables/disables expansion of Code 128 labels to Code 39 labels.
PAGE 109
1D Code Selection Enter/Exit Programming Mode Code 128 Check Character Transmission Enable this option to transmit the check character along with Code 128 barcode data. $CC8CT00(CR) DEFAULT Code 128 Check Character Transmission = Don’t Send $CC8CT01(CR) Code 128 Check Character Transmission = Send Code 128 Function Character Transmission Enables/disables transmission of Code128 function characters 1, 2, 3, and 4.
PAGE 110
Enter/Exit Programming Mode 1D Code Selection Code 128 Sub-Code Exchange Transmission Enables/disables the transmission of “Sub-Code Exchange” characters (NOT transmitted by standard decoding). $CC8SC00(CR) DEFAULT Code 128 Sub-Code Exchange Transmission = Disable $CC8SC01(CR) Code 128 Sub-Code Exchange Transmission = Enable Code 128 Quiet Zones This feature specifies the number of quiet zones for Code 128 labels.
PAGE 111
1D Code Selection Enter/Exit Programming Mode Code 128 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 128 symbology. See page 219 for more information.
PAGE 112
Enter/Exit Programming Mode 1D Code Selection Code 128 Set Length 1 Specifies one of the barcode lengths for Code 128 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 80 characters. Table 5 provides some examples for setting Length 1. See page 219 for detailed instructions on setting this feature. Table 5.
PAGE 113
1D Code Selection Enter/Exit Programming Mode Code 128 Set Length 2 This feature specifies one of the barcode lengths for Code 128 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 80 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 6 provides examples for setting Length 2.
PAGE 114
Enter/Exit Programming Mode 1D Code Selection GS1-128 The following options apply to the GS1-128 symbology. (Also known as USS-128, GS1128, GTIN-128, UCC-128, EAN-128.) GS1-128 Enable This option enables/disables the ability of the scanner to translate GS1-128 labels to the GS1-128 data format. Options are: • Transmit GS1-128 labels in Code 128 data format. • Transmit GS1-128 labels in GS1-128 data format. • Do not transmit GS1-128 labels.
PAGE 115
1D Code Selection Enter/Exit Programming Mode CODE ISBT 128 The following options apply to the ISBT 128 symbology. ISBT 128 Concatenation Use this option to enable/disable ISBT128 concatenation of 2 labels. $CI8CE00(CR) DEFAULT ISBN 128 Concatenation = Disable $CI8CE01(CR) ISBN 128 Concatenation = Enable ISBT 128 Force Concatenation When enabled, this feature forces concatenation for ISBT. This option is only valid when ISBT 128 Concatenation is enabled.
PAGE 116
Enter/Exit Programming Mode 1D Code Selection ISBT 128 Concatenation Mode Specifies the concatenation mode between Static and Dynamic. This option is only valid when ISBT 128 Concatenation is enabled (see "ISBT 128 Concate- nation" on page 105).
PAGE 117
1D Code Selection Enter/Exit Programming Mode ISBT 128 Dynamic Concatenation Timeout Specifies the timeout used by the ISBT 128 Dynamic Concatenation Mode.
PAGE 118
Enter/Exit Programming Mode 1D Code Selection INTERLEAVED 2 OF 5 (I 2 OF 5) The following options apply to the I 2 of 5 symbology. I 2 of 5 Enable/Disable When disabled, the scanner will not read I 2 of 5 barcodes.
PAGE 119
1D Code Selection Enter/Exit Programming Mode I 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional I 2 of 5 check character. Combinations of these settings are possible via the HP configuration utility, or contact Technical Support.
PAGE 120
Enter/Exit Programming Mode 1D Code Selection I 2 of 5 Check Character Transmission Enable this option to transmit the check character along with I 2 of 5 barcode data. $CI2CT00(CR) I 2 of 5 Check Character Transmission = Don’t Send $CI2CT01(CR) DEFAULT I 2 of 5 Check Character Transmission = Send I 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the I 2 of 5 symbology.
PAGE 121
1D Code Selection Enter/Exit Programming Mode I 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for I 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. The length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters in increments of two. Table 7 provides some examples for setting Length 1. See page 219 for detailed instructions on setting this feature.
PAGE 122
Enter/Exit Programming Mode 1D Code Selection I 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for I 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. The length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 8 provides examples for setting Length 2.
PAGE 123
1D Code Selection Enter/Exit Programming Mode INTERLEAVED 2 OF 5 CIP HR The following options apply to the Interleaved 2 of 5 CIP HR symbology. Interleaved 2 of 5 CIP HR Enable/Disable Enables/Disables ability of scanner to decode Interleaved 2 of 5 CIP HR labels. $CCHEN00(CR) DEFAULT Interleaved 2 of 5 CIP HR = Disable $CCHEN01(CR) Interleaved 2 of 5 CIP HR = Enable FOLLETT 2 OF 5 The following options apply to the Follett 2 of 5 symbology.
PAGE 124
Enter/Exit Programming Mode 1D Code Selection STANDARD 2 OF 5 The following options apply to the Standard 2 of 5 symbology. Standard 2 of 5 Enable/Disable When disabled, the scanner will not read Standard 2 of 5 barcodes. $C2SEN00(CR) DEFAULT Standard 2 of 5 = Disable $C2SEN01(CR) Standard 2 of 5 = Enable Standard 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional Standard 2 of 5 check character.
PAGE 125
1D Code Selection Enter/Exit Programming Mode Standard 2 of 5 Check Character Transmission This feature enables/disables transmission of an optional Standard 2 of 5 check character. $CS2CT00(CR) Standard 2 of 5 Check Character Transmission = Don’t Send $CS2CT01(CR) DEFAULT Standard 2 of 5 Check Character Transmission = Send Standard 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the Standard 2 of 5 symbology.
PAGE 126
Enter/Exit Programming Mode 1D Code Selection Standard 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for Standard 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 1 to 50 characters. Table 9 provides some examples for setting Length 1. See page 219 if you want detailed instructions on setting this feature.
PAGE 127
1D Code Selection Enter/Exit Programming Mode Standard 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Standard 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 10 provides examples for setting Length 2.
PAGE 128
Enter/Exit Programming Mode 1D Code Selection INDUSTRIAL 2 OF 5 The following options apply to the Industrial 2 of 5 symbology. Industrial 2 of 5 Enable/Disable Enables/Disables ability of scanner to decode Industrial 2 of 5 labels. $CU2EN00(CR) DEFAULT Industrial 2 of 5 = Disable $CU2EN01(CR) Industrial 2 of 5 = Enable Industrial 2 of 5 Check Character Calculation Enables/Disables calculation and verification of an optional Industrial 2 of 5 check character.
PAGE 129
1D Code Selection Enter/Exit Programming Mode Industrial 2 of 5 Check Character Transmission Enables/disables transmission of an Industrial 2 of 5 check character. $CU2CT00(CR) Industrial 2 of 5 Check Character Transmission = Disable $CU2CT01(CR) DEFAULT Industrial 2 of 5 Check Character Transmission = Enable Industrial 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the Industrial 2 of 5 symbology.
PAGE 130
Enter/Exit Programming Mode 1D Code Selection Industrial 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for Industrial 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 0 to 50 characters. Table 11 provides some examples for setting Length 1. See page 219 if you want detailed instructions on setting this feature.
PAGE 131
1D Code Selection Enter/Exit Programming Mode Industrial 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Industrial 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. The length can be set from 1 to 50 characters.
PAGE 132
Enter/Exit Programming Mode 1D Code Selection CODE IATA The following options apply to the IATA symbology. IATA Enable/Disable Enables/Disables the ability of the scanner to decode IATA labels. $CIAEN00(CR) DEFAULT IATA = Disable $CIAEN01(CR) IATA = Enable IATA Check Character Transmission Enables/Disables calculation and verification of an optional Industrial 2 of 5 check character.
PAGE 133
1D Code Selection Enter/Exit Programming Mode CODABAR The following options apply to the Codabar symbology. Codabar Enable/Disable When disabled, the scanner will not read Codabar barcodes. $CCBEN00(CR) DEFAULT Codabar = Disable $CCBEN01(CR) Codabar = Enable Codabar Check Character Calculation Enable this option to enables/disables calculation and verification of an optional Codabar check character.
PAGE 134
Enter/Exit Programming Mode 1D Code Selection Codabar Check Character Transmission Enable this option to transmit the check character along with Codabar barcode data. $CCBCT00(CR) Codabar Check Character Transmission = Don’t Send $CCBCT01(CR) DEFAULT Codabar Check Character Transmission = Send Codabar Start/Stop Character Transmission Enable this option to enable/disable transmission of Codabar start and stop characters.
PAGE 135
1D Code Selection Enter/Exit Programming Mode Codabar Start/Stop Character Set This option specifies the format of transmitted Codabar start/stop characters. $CCBSC00(CR) Codabar Check Character Set = ABCD/TN*E $CCBSC01(CR) Codabar Check Character Set = ABCD/ABCD $CCBSC02(CR) Codabar Check Character Set = abcd/tn*e $CCBSC03(CR) DEFAULT Codabar Check Character Set = abcd/abcd Codabar Start/Stop Character Match When enabled, this option requires that start and stop characters match.
PAGE 136
Enter/Exit Programming Mode 1D Code Selection Codabar Quiet Zones Specifies the number of quiet zones for Codabar labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 times the width of the narrowest bar or space in the label.
PAGE 137
1D Code Selection Enter/Exit Programming Mode Codabar Set Length 1 This feature specifies one of the barcode lengths for Codabar Length ControlCodabar Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s start, stop, check and data characters. The length must include at least one data character. The length can be set from 3 to 50 characters. Table 13 provides some examples for setting Length 1.
PAGE 138
Enter/Exit Programming Mode 1D Code Selection Codabar Set Length 2 This feature specifies one of the barcode lengths for Codabar Length ControlCodabar Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. The length includes the barcode’s start, stop, check and data characters. The length must include at least one data character. The length can be set from 3 to 50 characters.
PAGE 139
1D Code Selection Enter/Exit Programming Mode ABC CODABAR The following options apply to the ABC Codabar symbology. ABC Codabar Enable/Disable Enables/Disables ability of scanner to decode ABC Codabar labels. $CCBAB00(CR) DEFAULT ABC Codabar = Disable $CCBAB01(CR) ABC Codabar = Enable ABC Codabar Concatenation Mode Specifies the concatenation mode between Static and Dynamic.
PAGE 140
Enter/Exit Programming Mode 1D Code Selection ABC Codabar Dynamic Concatenation Timeout Specifies the timeout in 10-millisecond ticks used by the ABC Codabar Dynamic Concatenation Mode.
PAGE 141
1D Code Selection Enter/Exit Programming Mode ABC Codabar Force Concatenation Forces labels starting or ending with D to be concatenated.
PAGE 142
Enter/Exit Programming Mode 1D Code Selection CODE 11 The following options apply to the Code 11 symbology. Code 11 Enable/Disable When disabled, the scanner will not read Code 11 barcodes. $CC1EN00(CR) DEFAULT Code 11 = Disable $CC1EN01(CR) Code 11 = Enable Code 11 Check Character Calculation This option enables/disables calculation and verification of optional Code 11 check character.
PAGE 143
1D Code Selection Enter/Exit Programming Mode $CC1CC02(CR) Code 11 Check Character Calculation = Check K $CC1CC03(CR) DEFAULT Code 11 Check Character Calculation = Check C and K Code 11 Check Character Transmission This feature enables/disables transmission of an optional Code 11 check character.
PAGE 144
Enter/Exit Programming Mode 1D Code Selection Fixed Length: For fixed length decoding, two different lengths may be set.
PAGE 145
1D Code Selection Enter/Exit Programming Mode Code 11 Set Length 1 This feature specifies one of the barcode lengths for Code 11 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. Table 15 provides some examples for setting Length 1. See page 219 for detailed instructions on setting this feature. Table 15.
PAGE 146
Enter/Exit Programming Mode 1D Code Selection Code 11 Set Length 2 This feature specifies one of the barcode lengths for Code 11 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 16 provides examples for setting Length 2.
PAGE 147
1D Code Selection Enter/Exit Programming Mode GS1 DATABAR™ OMNIDIRECTIONAL The following options apply to the GS1 DataBar™ Omnidirectional (formerly RSS-14) symbology. GS1 DataBar™ Omnidirectional Enable/Disable When disabled, the scanner will not read GS1 DataBar™ Omnidirectional barcodes.
PAGE 148
Enter/Exit Programming Mode 1D Code Selection GS1 DataBar™ Omnidirectional 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label for this symbology is decoded.
PAGE 149
1D Code Selection Enter/Exit Programming Mode GS1 DataBar™ Expanded GS1-128 Emulation When enabled, GS1 DataBar™ Expanded barcodes will be translated to the GS1-128 label data format. $CXBU800(CR) DEFAULT GS1 DataBar™ Expanded GS1-128 Emulation = Disable $CXBU801(CR) GS1 DataBar™ Expanded GS1-128 Emulation = Enable GS1 DataBar™ Expanded 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded.
PAGE 150
Enter/Exit Programming Mode 1D Code Selection GS1 DataBar™ Expanded Length Control This feature specifies either variable length decoding or fixed length decoding for the GS1 DataBar™ Expanded symbology. Variable Length: For variable-length decoding, a minimum length may be set. Fixed Length: For fixed-length decoding, two different lengths may be set.
PAGE 151
1D Code Selection Enter/Exit Programming Mode GS1 DataBar™ Expanded Set Length 1 This feature specifies one of the barcode lengths for GS1 DataBar™ Expanded Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 74 characters. Table 17 provides some examples for setting Length 1. See page 219 for detailed instructions on setting this feature.
PAGE 152
Enter/Exit Programming Mode 1D Code Selection GS1 DataBar™ Expanded Set Length 2 This feature specifies one of the barcode lengths for GS1 DataBar™ Expanded Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 74 characters. A setting of 0 specifies to ignore this length (only one fixed length). Table 18 provides examples for setting Length 2.
PAGE 153
1D Code Selection Enter/Exit Programming Mode GS1 DATABAR™ LIMITED The following options apply to the GS1 DataBar™ Limited (formerly RSS Limited) symbology. GS1 DataBar™ Limited Enable/Disable When disabled, the scanner will not read GS1 DataBar™ Limited barcodes. $CLBEN00(CR) DEFAULT GS1 DataBar™ Limited = Disable $CLBEN01(CR) GS1 DataBar™ Limited = Enable GS1 DataBar™ Limited GS1-128 Emulation When enabled, GS1 DataBar™ Limited barcodes will be translated to the GS1-128 label data format.
PAGE 154
Enter/Exit Programming Mode 1D Code Selection GS1 DataBar™ Limited 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded. $CLB2D00(CR) DEFAULT GS1 DataBar™ Limited 2D Component = Disable (2D component not required) $CLB2D01(CR) GS1 DataBar™ Limited 2D Component = 2D component must be decoded CODE 93 The following options apply to the Code 93 symbology.
PAGE 155
1D Code Selection Enter/Exit Programming Mode Code 93 Check Character Calculation Enables/disables calculation and verification of an optional Code 93 check character.
PAGE 156
Enter/Exit Programming Mode 1D Code Selection Code 93 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 93 symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
PAGE 157
1D Code Selection Enter/Exit Programming Mode Code 93 Set Length 1 Specifies one of the barcode lengths for Code 93 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 01 to 50 characters. Table 19 provides some examples for setting Length 1. See page 219 for detailed instructions on setting this feature. Table 19.
PAGE 158
Enter/Exit Programming Mode 1D Code Selection Code 93 Set Length 2 This feature specifies one of the barcode lengths for Code 93 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length).
PAGE 159
1D Code Selection Enter/Exit Programming Mode Code 93 Quiet Zones Enables/disables quiet zones for Code 93. $CC9LO02(CR) Code 93 Quiet Zones = Quiet Zones on two sides $CC9LO03(CR) DEFAULT Code 93 Quiet Zones = Small Quiet Zones on two sides MSI The following options apply to the MSI symbology. MSI Enable/Disable Enables/Disables ability of scanner to decode MSI labels.
PAGE 160
Enter/Exit Programming Mode 1D Code Selection MSI Check Character Calculation Enables/Disables calculation and verification of an optional MSI check character. $CMSCC00(CR) MSI Check Character Calculation = Disable $CMSCC01(CR) DEFAULT MSI Check Character Calculation = Enable Mod10 $CMSCC02(CR) MSI Check Character Calculation = Enable Mod11/10 $CMSCC03(CR) MSI Check Character Calculation = Enable Mod10/10 MSI Check Character Transmission Enables/disables transmission of an MSI check character.
PAGE 161
1D Code Selection Enter/Exit Programming Mode MSI Length Control This feature specifies either variable length decoding or fixed length decoding for the MSI symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
PAGE 162
Enter/Exit Programming Mode 1D Code Selection MSI Set Length 1 This feature specifies one of the barcode lengths for MSI Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 01 to 50 characters. Table 21 provides some examples for setting Length 1. See page 219 for detailed instructions on setting this feature. Table 21.
PAGE 163
1D Code Selection Enter/Exit Programming Mode MSI Set Length 2 This feature specifies one of the barcode lengths for MSI Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length).
PAGE 164
Enter/Exit Programming Mode 1D Code Selection PLESSEY The following options apply to the Plessey symbology. Plessey Enable/Disable Enables/Disables ability of scanner to decode Plessey labels. $CPLEN00CR) DEFAULT Plessey = Disable $CPLEN01CR) Plessey = Enable Plessey Check Character Calculation Enables/Disables calculation and verification of an optional Plessey check character.
PAGE 165
1D Code Selection Enter/Exit Programming Mode Plessey Check Character Transmission Enables/disables transmission of an MSI check character. $CPLCT00(CR) Plessey Check Character Transmission = Disable $CPLCT01(CR) DEFAULT Plessey Check Character Transmission = Enable Plessey Length Control This feature specifies either variable length decoding or fixed length decoding for the Plessey symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set.
PAGE 166
Enter/Exit Programming Mode 1D Code Selection Plessey Set Length 1 This feature specifies one of the barcode lengths for Plessey Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 01 to 50 characters. Table 23 provides some examples for setting Length 1. See page 219 for detailed instructions on setting this feature. Table 23.
PAGE 167
1D Code Selection Plessey Set Length 2 This feature specifies one of the barcode lengths for Plessey Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length).
PAGE 168
NOTES 158 HP Wireless Barcode Scanner
PAGE 169
2D SYMBOLOGIES 2D Global Features • • 2D Maximum Decoding Time, page 160 2D Structured Append, page 161 • 2D Normal/Inverse Symbol Control, page 161 The reader supports the following 2D symbologies (barcode types). Symbology-dependent options for each symbology are included in this chapter. See "1D Code Selection" starting on page 65 for configuration of 1D barcodes.
PAGE 170
Enter/Exit Programming Mode 2D Global Features 2D Maximum Decoding Time This feature specifies the maximum amount of time the software will spend attempting to decode a 2D label. The selectable range is 10 milliseconds to 2.55 milliseconds.
PAGE 171
2D Global Features Enter/Exit Programming Mode 2D Structured Append Enables/disables ability of reader to append multiple 2D Codes labels in a structured format.
PAGE 172
Enter/Exit Programming Mode Aztec Code Aztec Code Aztec Code Enable / Disable Enables/disables the ability of the reader to decode Aztec Code labels. $CAZEN00(CR) DEFAULT Aztec Code = Disable $CAZEN01(CR) Aztec Code = Enable Aztec Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set.
PAGE 173
Aztec Code Enter/Exit Programming Mode Aztec Code Set Length 1 Specifies one of the barcode lengths for Aztec Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 3,832 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 174
Enter/Exit Programming Mode Aztec Code Aztec Code Set Length 2 This feature specifies one of the barcode lengths for Aztec Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 3,832 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 175
China Sensible Code Enter/Exit Programming Mode China Sensible Code China Sensible Code Enable / Disable Enables/disables the ability of the reader to decode China Sensible Code labels. $CCSEN00(CR) DEFAULT China Sensible Code = Disable $CCSEN01(CR) China Sensible Code = Enable China Sensible Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set.
PAGE 176
Enter/Exit Programming Mode China Sensible Code China Sensible Code Set Length 1 Specifies one of the barcode lengths for China Sensible Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 7,827 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 177
China Sensible Code Enter/Exit Programming Mode China Sensible Code Set Length 2 This feature specifies one of the barcode lengths for China Sensible Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 7,827 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 178
Enter/Exit Programming Mode Data Matrix Data Matrix Data Matrix Enable / Disable Enables/disables ability of reader to decode Data Matrix labels. $CDMEN00(CR) Data Matrix = Disable $CDMEN01(CR) DEFAULT Data Matrix = Enable Data Matrix Square/Rectangular Style Specifies the options available when reading Data Matrix with different form factors.
PAGE 179
Data Matrix Enter/Exit Programming Mode Data Matrix Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
PAGE 180
Enter/Exit Programming Mode Data Matrix Data Matrix Set Length 2 This feature specifies one of the barcode lengths for Data Matrix Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 3,116 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 181
Maxicode Enter/Exit Programming Mode Maxicode Maxicode Enable / Disable Enables/disables ability of reader to decode Maxicode labels. $CMXEN00(CR) DEFAULT Maxicode = Disable $CMXEN01(CR) Maxicode = Enable Maxicode Primary Message Transmission Enables/disables the transmission of only the Primary Message when the Secondary Message is not readable.
PAGE 182
Enter/Exit Programming Mode Maxicode Maxicode Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
PAGE 183
Maxicode Enter/Exit Programming Mode Maxicode Set Length 2 This feature specifies one of the barcode lengths for Maxicode Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 0145 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 184
Enter/Exit Programming Mode PDF417 PDF417 PDF417 Enable / Disable Enables/disables the ability of the reader to decode PDF417 labels. $CP4EN00(CR) PDF417 = Disable $CP4EN01(CR) DEFAULT PDF417 = Enable PDF417 Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
PAGE 185
PDF417 Enter/Exit Programming Mode PDF417 Set Length 1 Specifies one of the barcode lengths for PDF417 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. Characters can be set from 0001 to 2,710 characters (pad with zeroes) in increments of 01. Any value greater than 2,710 will be considered to be 2,710. See page 219 for detailed instructions on setting this feature.
PAGE 186
Enter/Exit Programming Mode PDF417 PDF417 Set Length 2 This feature specifies one of the barcode lengths for PDF417 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. Characters can be set from 01 to 2,710 characters (pad with zeroes) in increments of 01.
PAGE 187
Micro PDF417 Enter/Exit Programming Mode Micro PDF417 Micro PDF417 Enable / Disable Enables/disables the ability of the reader to decode Micro PDF417 labels. $CMIEN00(CR) DEFAULT Micro PDF417 = Disable $CMIEN01(CR) Micro PDF417 = Enable Micro PDF417 Code 128 GS1-128 Emulation Specifies which AIM ID to use for MicroPDF labels when doing Code 128 or GS1-128 emulation.
PAGE 188
Enter/Exit Programming Mode Micro PDF417 Micro PDF417 Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
PAGE 189
Micro PDF417 Enter/Exit Programming Mode Micro PDF417 Set Length 2 This feature specifies one of the barcode lengths for Micro PDF417 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length includes the barcode’s data characters only. Characters can be set from 0001 to 0366 characters (pad with zeroes) in increments of 01. Any value greater than 0366 will be considered to be 0366.
PAGE 190
Enter/Exit Programming Mode QR Code QR Code QR Code Enable / Disable Enables/disables the ability of the reader to decode QR Code labels. $CQREN00(CR) QR Code = Disable $CQREN01(CR) DEFAULT QR Code = Enable QR Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
PAGE 191
QR Code Enter/Exit Programming Mode QR Code Set Length 1 Specifies one of the barcode lengths for QR Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 7,089 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 192
Enter/Exit Programming Mode QR Code QR Code Set Length 2 This feature specifies one of the barcode lengths for QR Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 7,089 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 193
Micro QR Code Enter/Exit Programming Mode Micro QR Code Micro QR Code Enable/Disable Enables/disables the ability of the reader to decode Micro QR Code labels. MQEN00 DEFAULT Micro QR Code = Disable MQEN01 Micro QR Code = Enable Micro QR Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set.
PAGE 194
Enter/Exit Programming Mode Micro QR Code Micro QR Code Set Length 1 Specifies one of the barcode lengths for Micro QR Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 0035 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 195
Micro QR Code Enter/Exit Programming Mode Micro QR Code Set Length 2 This feature specifies one of the barcode lengths for Micro QR Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Characters can be set from 0001 to 0035 characters in increments of 0001 (pad with zeroes). See page 219 for detailed instructions on setting this feature.
PAGE 196
Enter/Exit Programming Mode UCC Composite UCC Composite UCC Composite Enable / Disable Enables/disables the ability of the reader to decode the stacked part of a UCC Composite label. This feature is not effective when Global AIM IDs are enabled (see "Global AIM ID" on page 33).
PAGE 197
UCC Composite Enter/Exit Programming Mode UCC Optional Composite Timer Specifies the amount of time the system will wait for the stacked part of a UCC Composite label before transmitting the linear label without an add-on.
PAGE 198
Enter/Exit Programming Mode Postal Code Selection Postal Code Selection Enables/disables the ability of the scanner to decode labels of a specific postal symbology.
PAGE 199
Postal Code Selection Enter/Exit Programming Mode Postal Code Selection (continued) $CPOEN06(CR) Postal Code Selection = Enable Japan Post $CPOEN07(CR) Postal Code Selection = Enable IMB $CPOEN08(CR) Postal Code Selection = Enable Sweden Post $CPOEN09(CR) Postal Code Selection = Enable Portugal Post Postnet BB Control Controls the ability of the scanner to decode B and B' fields of Postnet labels.
PAGE 200
NOTES 190 HP Wireless Barcode Scanner
PAGE 201
WIRELESS-SPECIFIC FEATURES This section provides options and programming related to the scanner’s wireless communication features. Reference Appendix B. for a listing of standard factory settings.
PAGE 202
Enter/Exit Programming Mode Wireless Beeper Features Several options are available to configure beeper behavior for RF operation. Good Transmission Beep Enables/disables the Good Transmission Beep indication. When enabled, a beep occurs when a Label is correctly transmitted to the base.
PAGE 203
Enter/Exit Programming Mode Beep Duration This feature controls the duration of radio-specific beep indications.
PAGE 204
Enter/Exit Programming Mode Beep Volume Selects the beeper volume (loudness) of radio-specific beep indications. There are three selectable volume levels. $CBTBV00(CR) Beep Volume = Low $CBTBV01(CR) Beep Volume = Medium $CBTBV02(CR) DEFAULT Beep Volume = High Disconnect Beep Enables/disables the beep indication that a handheld has become connected or disconnected from a Base Station. The defaults are different for the STAR and BT models.
PAGE 205
Enter/Exit Programming Mode Docking Beep Enables/disables a beep indication when the handheld is placed in the Base Station. $CBTCB00(CR) Docking Beep = Disable $CBTCB01(CR) DEFAULT Docking Beep = Enable Leash Alarm This setting specifies the number of seconds to sound the Leash Mode beeps (three per second) when the handheld goes out of range. This is especially useful in instances where the scanner might inadvertently have been placed in a bag or cart.
PAGE 206
Enter/Exit Programming Mode Leash Alarm (continued) $CBTLB03(CR) Leash Alarm = 3 Seconds $CBTLB04(CR) Leash Alarm = 4 Seconds $CBTLB05(CR) Leash Alarm = 5 Seconds $CBTLB0A(CR) Leash Alarm = 10 Seconds $CBTLB19(CR) Leash Alarm = 25 Seconds $CBTLB1E(CR) Leash Alarm = 30 Seconds 196 HP Wireless Barcode Scanner
PAGE 207
Enter/Exit Programming Mode Configuration Updates See page 238 in “References” for detailed information and examples of these features. Automatic Configuration Update When this feature is enabled, a scanner and its linked Base Station can automatically ensure they stay in sync with regard to application hardware and/or configuration. See page 238 for more information on this feature.
PAGE 208
Enter/Exit Programming Mode Batch Features Batch Mode This option specifies whether to store labels in the handheld while disconnected from the base. Options are as follows: • Disabled — The handheld will not store/batch labels. • • Automatic — The handheld will store labels to memory when the handheld goes out of range and is disconnected from the remote device. Manual — The handheld will always store labels to Flash memory.
PAGE 209
Enter/Exit Programming Mode Erase Batch Memory When the scanner is configured in Manual Batch Mode, use the following barcode to erase any labels stored in batch memory. Do not scan an ENTER/EXIT PROGRAMMING MODE label in conjunction with this barcode. Erase Batch Memory RF Batch Mode Transmit Delay Specifies the delay in 10 msec increments between transmitting labels stored in batch memory.
PAGE 210
Enter/Exit Programming Mode $CBTTDFA(CR) RF Batch Mode Transmit Delay = 2.5 seconds Direct Radio Autolink This feature enables/disables the ability to link a wireless handheld to a base station without scanning the Unlink label first.
PAGE 211
Enter/Exit Programming Mode BLUETOOTH-SPECIFIC FEATURES The features in this section are specific to Bluetooth wireless operation. Also reference the Setup section for instructions on Linking the BT Scanner to a PC, starting on page 7. RF Address Stamping These features allow configuration of source radio data inclusion.
PAGE 212
Enter/Exit Programming Mode Source Radio Address Delimiter Character This option specifies the delimiter character to be placed between the label data and radio address when address stamping is enabled. This feature only applies if "Source Radio Address Transmission" on page 201 is enabled. $CBTAD Set Source Radio Address Delimiter Character Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 213
Enter/Exit Programming Mode BT Security Features On the BT system, it is possible to set a (configurable) PIN code to authenticate/connect BT devices, and encrypt the data. The BT PIN code can be enabled and configured by reading the barcodes in the following sections. If you are using a BT scanner directly connected to a host through a BT dongle, verify that the scanner and the BT driver used by the dongle share the same PIN code and the same security level. Otherwise the connection cannot be established.
PAGE 214
Enter/Exit Programming Mode BT PIN Code After enabling Security Mode (see "BT Security Mode" on page 203), specify whether you want to set a 4-digit or a 16-digit PIN Code. See page 239 for detailed information and examples for setting this feature.
PAGE 215
Enter/Exit Programming Mode Other BT Features BT Poll Rate This feature specifies the time between BT polls.
PAGE 216
Enter/Exit Programming Mode Power Off See “Power Off” on page 7 for information about this BT feature. Powerdown Timeout The Powerdown Timeout feature sets the time for automatically switching the unit off when the imager has been idle.
PAGE 217
MOTION FEATURES MOTION AIMING CONTROL on page 207 MOTION SENSITIVITY on page 208 MOTIONLESS TIMEOUT on page 208 Use this chapter to configure motion settings for the handheld. Reference Appendix B for a listing of standard factory settings. Motion Aiming Control Configures the ability of the scanner to Enable/Disable the Aiming system when motion is detected.
PAGE 218
Enter/Exit Programming Mode Motion Sensitivity Defines discrete set of levels for scanner motion sensitivity when in handheld use. $CMOSY00(CR) Motion Sensitivity = Low $CMOSY01(CR) DEFAULT Motion Sensitivity = Medium $CMOSY02(CR) Motion Sensitivity = High Motionless Timeout Specifies the waiting time in 100 millisecond ticks to assume that the scanner is in a motionless condition. The selectable range is 500 msec to 25.5 Seconds.
PAGE 219
Chapter 4 References This section contains explanations and examples of selected barcode features. See "Configuration Using Barcodes" starting on page 11 for the actual barcode labels used to configure the scanner.
PAGE 220
References USB-COM Parameters Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. To set the delay: 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 10 (setting is in 10ms increments). Pad the result with leading zeroes to yield two digits.
PAGE 221
USB-COM Parameters ACK NAK Options This enables/disables the ability of the scanner to support the RS-232 ACK/NAK protocol. When configured, the scanner and/or host sends an “ACK” when it receives data properly, and sends “NAK” when the data is in error. Options are: • Disable • Enable for label transmission — The scanner expects an ACK/NAK response from the host when a label is sent. • Enable for host-command acknowledge — The scanner will respond with ACK/NAK when the host sends a command.
PAGE 222
References NAK Character This setting specifies an ASCII character or hex value to be used as the NAK character. ASCII characters or any hex value from 0 to 0xFF can be selected. Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of this character. To set this feature: 1. Determine the desired character or value. 2. Use the ASCII Chart on the inside back cover of this manual to find the hex equivalent for the desired character/value. 3.
PAGE 223
USB-COM Parameters 2. Divide the desired setting by 200 (setting is in 200ms increments). Pad the result with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc. 3. Go to page 20 and scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4. Scan the barcode: SELECT ACK NAK TIMEOUT VALUE SETTING. 5. Scan the appropriate two digits from the keypad in Appendix D, Keypad, that represent the duration which was determined in the steps above.
PAGE 224
References ACK NAK Retry Count This feature specifies the number of times the scanner retries a label transmission due to a retry condition. The selectable range is from 1 to 254 retries. A selection of 0 disables the count, and a selection of 255 specifies unlimited retries. To set this feature: 1. Determine the desired setting. 2. Pad the number with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20 = 020, etc. 3.
PAGE 225
USB-COM Parameters Disable Character Specifies the value of the host command used to disable the scanner. ASCII characters or any hex value from 0 to 0xFF can be selected. Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of this character. To set the value: 1. Determine the desired character or value. A setting of 0xFF indicates the Disable Character is not used (not available). 2.
PAGE 226
References Enable Character Specifies the value of the host command used to enable the scanner. ASCII characters or any hex value from 0 to 0xFF can be selected. Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of this character. To set this feature: Determine the desired character or value. A setting of 0xFF indicates the Enable Character is not used (not available). 1. Determine the desired character or value. 2.
PAGE 227
USB Keyboard Interface USB Keyboard Interface Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. This feature applies ONLY to the Keyboard Wedge interface. To set the delay: 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 10 (setting is in 10ms increments).
PAGE 228
References Intercode Delay Specifies the delay between labels transmitted to the host for this interface. The selectable range for this feature is from 0 to 99 seconds. Follow these instructions to set this feature: 1. Determine the desired setting. 2. Pad the number with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc 3. Go to page 28 and scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4. Scan the barcode: SELECT INTERCODE DELAY SETTING. 5.
PAGE 229
Symbologies Symbologies Set Length Length Control allows you to select either variable length decoding or fixed length decoding for the specified symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set. Set Length 1 This feature specifies one of the barcode lengths for Length Control.
PAGE 230
References 3. Scan the barcode to SELECT LENGTH 2 SETTING for your selected symbology. 4. Scan the appropriate two digits from the keypad in Appendix D, Keypad that represent the length setting which was determined in the steps above. You will hear a two-beep indication after the last character. If you make a mistake, before the last character scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. 5.
PAGE 231
Data Editing • • • A prefix or suffix may be applied only to a specified symbology (reference "1D Code Selection" starting on page 65) or across all symbologies (set via the Global features in this chapter). You can add any character from the ASCII Chart (from 00-FF) on the inside back cover of this manual as a prefix, suffix or Label ID. Enter prefixes and suffixes in the order in which you want them to appear on the output.
PAGE 232
References Global AIM ID This feature enables/disables addition of AIM IDs for all symbology types. AIM label identifiers (as opposed to custom characters you select yourself as with label identifiers) can be included with scanned barcode data. AIM label identifiers consist of three characters as follows: • A close brace character (ASCII ‘]’), followed by... • A code character (see the table below), followed by... • A modifier character (the modifier character is symbol dependent).
PAGE 233
Data Editing Label ID A Label ID is a customizable code of up to three ASCII characters (each can be one of hex 0x01-0xFF), used to identify a barcode (symbology) type. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled. This feature provides options for configuring custom Label IDs as a pre-loaded set (see "Label ID: Pre-loaded Sets" below) or individually per symbology (see "Label ID: Set Individually Per Symbology" on page 226).
PAGE 234
References USA Label ID set Symbology EU Label ID set Default Character Default ASCII Default Character Default ASCII DATABAR 14 R4 523400 u 750000 DATABAR 14 COMPOSITE R4 523400 c 523400 DATABAR EXPANDED RX 525800 t 740000 DATABAR EXPANDED COMPOSITE RX 525800 d 525800 DATABAR LIMITED RL 524C00 v 760000 DATABAR LIMITED COMPOSITE RL 524C00 i 524C00 DATA MATRIX Dm 446D00 w 770000 EAN128 000000 k 6B0000 EAN128 COMPOSITE 000000 $E 244500 EAN13 F 460000 B 4200
PAGE 235
Data Editing USA Label ID set Symbology EU Label ID set Default Character Default ASCII Default Character Default ASCII MICRO QR $Q 245100 $Q 245100 MICRO PDF mP 6D5000 8 380000 MSI @ 400000 Z 5A0000 PDF417 P 500000 r 720000 PLESSEY a 610000 a 610000 POSTAL AUSTRALIAN $K 244B00 $K 244B00 POSTAL IMB $V 245600 $V 245600 POSTAL JAPANESE $R 245200 $R 245200 POSTAL KIX $U 245500 $U 245500 POSTAL PLANET $W 245700 $W 245700 POSTAL PORTUGAL $P 245000 $P 24
PAGE 236
References Label ID: Set Individually Per Symbology To configure a Label ID individually for a single symbology: 1. Go to page 37 and scan the ENTER/EXIT barcode. 2. Select Label ID position as either BEFORE (Enable as Prefix) or AFTER (Enable as suffix) by scanning the appropriate barcode in the section "Label ID Control" on page 37. Reference Figure 4 for Label ID positioning options if multiple identification features are enabled. 3.
PAGE 237
Data Editing Table 35. Label ID Examples STEP ACTION EXAMPLES 1. Scan the ENTER/EXIT barcode (Scanner enters Programming Mode) 2. Determine placement of the Label ID characters BEFORE or AFTER with regard to scanned Enable as Prefix data using "Label ID Control" starting on page 37 Enable as Suffix Enable as Prefix Enable as Suffix 3.
PAGE 238
References Character Conversion Character conversion is an eight byte configuration item. The eight bytes are 4 character pairs represented in hexadecimal ASCII values. The first character in the pair is the character that will be converted. The second character in the pair is the character to convert to. If the character to convert in a pair is FF, then no conversion is done.
PAGE 239
Reading Parameters Reading Parameters Good Read LED Duration This feature specifies the amount of time that the Good Read LED remains on following a good read. The good read LED on time can be set within a range of 10 milliseconds to 2,550 milliseconds (0.001 to 2.55 seconds) in 100ms increments. Follow these instructions to set this feature: 1. Determine the desired setting in milliseconds. A setting of 0 means that the good read LED stays on until the next time the trigger is pulled. 2.
PAGE 240
References Scanning Features Scan Mode This mode is associated with typical handheld scanner operation. Selects the scan operating mode for the scanner.
PAGE 241
Scanning Features Stand Mode Off Time This feature specifies the amount of time scanner illumination stays off after pulling the trigger when in Stand Mode. The configurable range is 01 to 32 by 01 in increments of 500ms (500ms to 16 seconds). Follow these instructions to set this feature: 1. Determine the desired setting. 2. Pad the result with leading zeroes to yield two digits. For example: 2 = 02, 5 = 05, 20 = 20, etc. 3.
PAGE 242
References Scanning Active Time This setting specifies the amount of time that the scanner stays in scan ON state once the state is entered. The range for this setting is from 1 to 255 seconds in 1-second increments. Follow these instructions to set this feature: 1. Determine the desired setting. 2. Pad the result with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20 = 020, etc. 3. Go to page 57 and scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4.
PAGE 243
Scanning Features Aiming Duration Time Specifies the frame of time the aiming pointer remains on after decoding a label, when in trigger single mode. The range for this setting is from 1 to 255 seconds in 1-second increments. Follow these instructions to set this feature: 1. Determine the desired setting. 2. Pad the result with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20 = 020, etc. 3. Go to page 60 and scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4.
PAGE 244
References Flash On Time This feature specifies the ON time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. Follow these instructions to set this feature. 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 100 (setting is in 100ms increments). Pad the result with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc. 3.
PAGE 245
Scanning Features Flash Off Time This feature specifies the OFF time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. Follow these instructions to set this feature. 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 100 (setting is in 100ms increments). Pad the result with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc. 3.
PAGE 246
References Multiple Labels Ordering by Code Symbology This feature Specifies the transmission ordering by symbology type, when Multiple Labels per Frame is enabled.Up to six symbologies can be selected. Zeroes must be added to pad the string to 12 characters if not using all six symbologies. The labels are ordered first as specified in the output mask. Labels present in the volume but not specified will be transmitted as unspecified symbologies in random order as allowed by the reading time sequence.
PAGE 247
Scanning Features Table 43.
PAGE 248
References Hex Value Symbology ID 29 2A 2B Hex Value 54 RSS_14_ID GTIN GTIN2 55 FF Symbology ID DATA MATRIX_PROGRAMMING_LAB EL LABEL_ID_MAX INVALID_LABEL_TYPE RF Features Automatic Configuration Update When this feature is enabled, the base station and scanner will keep their configurations synchronized. If a scanner's configuration is altered by reading programming labels, this change is automatically transferred and updated in a linked base station.
PAGE 249
RF Features Table 44.
PAGE 250
References Table 45.
PAGE 251
Motion Features STEP ACTION EXAMPLES 1 Desired Setting 500ms 1 sec. 10 sec 9,900ms (9.9 sec.
PAGE 252
References NOTES 242 HP Wireless Barcode Scanner
PAGE 253
Chapter 5 Message Formatting Message Formatting A message from the Host to the base must follow these rules: • If Address stamping options or address delimiter are enabled on the base, the Host replay must have address field and delimiter too. Otherwise the message will be ignored. Address delimiter is present only when address stamping is enabled. • Address stamping is necessary to correctly route the message to the scanner, especially when more than one handheld is linked to the same base.
PAGE 254
Message Formatting • Escape sequences are interpreted as commands.
PAGE 255
Appendix A Technical Specifications Table 47 contains Physical and Performance Characteristics, User Environment and Regulatory information. Table 47. Technical Specifications Item Description HP Wireless Barcode Scanner Physical Characteristics Color Dimensions Weight (without cable) Black Height 7.1”/181 mm Length 3.9”/100 mm Width 2.8”/71 mm Handheld Unit: Approximately 8.7 ounces/246 g Base Station/Charger: Approximately 8.
PAGE 256
Technical Specifications Item Description Roll (Tilt) Anglec Up to ± 180° Pitch Anglec ± 40° Skew (Yaw) Anglec ± 40° Field of View 40° Hx26° V Depth of Field (Typical) d Symbology 5mil: 1.6” -7.5” (4.0 -19cm) Code 39 10mil: 0.4” - 11.8” (1.0 - 30cm) 20mil: up to 17.7” (up to 45cm) EAN 7.5mil: 0.5” - 10.6” (2.0 - 27cm) 13mil: 0.6” - 15.7” (1.5 - 40cm) 6.6mil: 1.0” - 5.9” (2.5 - 15cm) PDF 417 10mil: 0.2” - 8.6” (0.5 - 22cm) 15mil: 0.6” - 13.4” (1.5 - 34cm) Data Matrix QR Code 10mil: 0.
PAGE 257
Technical Specifications Item Description 1D Barcodes UPC/EAN/JAN (A, E, 13, 8); UPC/EAN/JAN (including P2 /P5); UPC/EAN/ JAN (including; ISBN /Bookland & ISSN); UPC/EAN Coupons; Code 39 (including full ASCII); Code 39 Trioptic; Code39 CIP (French Pharmaceutical); LOGMARS (Code 39 w/ standard check digit enabled); Danish PPT; Code 32 (Italian Pharmacode 39); Code 128; Code 128 ISBT; Interleaved 2 of 5; Standard 2 of 5; Interleaved 2 of 5 CIP (HR); Industrial 2 of 5; Discrete 2 of 5; IATA 2of5 Air cargo cod
PAGE 258
Technical Specifications Item Description User Environment Operating Temperature 32° to 122° F (0° to 50° C) Charging Temperature 32° to 104° F (0° to 40° C) Storage Temperature -4° to 158° F (-20° to 70° C) Humidity Drop Specifications Scanner withstands 18 drops from 1.8 meters (5.
PAGE 259
Technical Specifications Imager Labeling Sample labels are shown for illustrative purposes only. Please view the labels on the product for actual details. Scanner Regulatory Label Base Station Label C PATENTS PENDING 239045 US Radio Features Radio Features Frequency Range 2400 to 2483.
PAGE 260
Technical Specifications Standard Cable Pinouts Figure 5 and Table 48 provide standard pinout information for the interface cable. Figure 5. Standard Cable Pinouts: Base Station Cable Strain Relief To Host Cable Clip (Latch) Cable The signal descriptions in Table 48 apply to the connector in the base station and are for reference only. Table 48.
PAGE 261
Technical Specifications LED and Beeper Indications The scanner’s beeper sounds and its LED illuminates to indicate various functions or errors on the scanner. An optional “Green Spot” also performs useful functions. The tables below list these indications. One exception to the behaviors listed in the tables is that the scanner’s functions are programmable, and may or may not be turned on. For example, certain indications such as the power-up beep can be disabled using programming barcode labels. Table 49.
PAGE 262
Technical Specifications Table 50. Programming Mode Indications Programming Mode - The following indications ONLY occur when the scanner is in Programming Mode. Label Programming Mode Entry A valid programming label has been scanned. LED blinks continuously Scanner sounds four low frequency beeps. Label Programming Mode Rejection of Label A label has been rejected. N/A Scanner sounds three times at lowest frequency & current volume.
PAGE 263
Technical Specifications Base Station Indications INDICATION LEDS Power-up Complete Yellow LED on Scanner Disabled by the HOST or the communication with HOST is not established Yellow LED blinking ~1Hz Data/labels are transmitted to the HOST Yellow LEDs turned off for 100mSec Programming Mode Yellow LED blinks quickly Configuration alignment with the handheld is in progress Red LED blinks quickly Battery charging in progress Red LED on Battery charging complete Green LED on Battery charger
PAGE 264
Technical Specifications NOTES 254 HP Wireless Barcode Scanner
PAGE 265
Appendix B Standard Defaults The most common configuration settings are listed in the “Default” column of the table below. Page references are also provided for feature descriptions and programming barcodes for each parameter. A column has also been provided for recording of your preferred default settings for these same configurable features. Table 51.
PAGE 266
Standard Defaults Parameter USB Keyboard Numeric Keypad Default Your Setting Page Number Standard Keys 30 No Global Prefix Global Suffix = 0x0D (CR) 32 Global AIM ID Disable 33 Set AIM ID Individually for GS1-128 Enable 35 Label ID: Pre-Loaded Sets EU Set 36 Individually Set Label ID Disable 37 Case Conversion Disable 43 No Char Conversion 44 0.
PAGE 267
Standard Defaults Parameter Default Your Setting Page Number Flash Off Time 06 = Flash is OFF for 600ms 59 Aiming Pointer Enable 60 Aiming Off After Decoding 60 Green Spot Duration 300 ms 61 Mobile Phone Mode Enable 61 Partial Label Reading Control Enable 62 Decode Negative Image Disable 62 Disable 63 Random Order 64 Disable 64 Enable only UPCA coupon decoding 67 Enable 68 Send 68 Don’t Expand 69 Transmit 69 2D Component Not Required 70 Enable 70 Send 71 2D Comp
PAGE 268
Standard Defaults Parameter UPC-E Number System Character Transmission Default Your Setting Page Number Transmit 73 Disable 73 Enable 74 Send 74 EAN-13 Flag 1 Character Transmit 75 EAN-13 ISBN Conversion Disable 75 2D Component Not Required 76 Disable 76 Enable 77 Send 77 Disable 78 2D Component Not Required 78 Disable 79 Two Modules 80 Disable P2, P5 and P8 81 70 ms 82 Disable 85 Enable 88 Calculate Std Check 88 Send 89 Don’t Transmit 90 Disable 90 GTIN GT
PAGE 269
Standard Defaults Parameter Default Your Setting Page Number Small Quiet Zones on two sides 91 Variable 91 Code 39 Set Length 1 2 92 Code 39 Set Length 2 50 93 Disable 94 Disable 94 Don’t Send 95 Don’t Transmit 95 Disable 96 Code 39 Danish PPT Enable/Disable Disable 96 Code 39 LaPoste Enable/Disable Disable 97 Code 39 PZN Enable/Disable Disable 97 Enable 98 Don’t Expand 98 Code 128 Check Character Transmission Don’t Send 99 Code 128 Function Character Transmission Do
PAGE 270
Standard Defaults Parameter Default Your Setting Page Number ISBT 128 ISBT 128 Concatenation Disable 105 ISBT 128 Force Concatenation Disable 105 ISBT 128 Concatenation Mode Static 106 200 msec 107 I 2 of 5 Enable/Disable Disable 108 I 2 of 5 Check Character Calculation Disable 109 Send 110 Variable 110 I 2 of 5 Set Length 1 6 111 I 2 of 5 Set Length 2 50 112 Disable 113 Disable 113 Standard 2 of 5 Enable/Disable Disable 114 Standard 2 of 5 Check Character Calculation
PAGE 271
Standard Defaults Parameter Industrial 2 of 5 Set Length 2 Default Your Setting Page Number 50 121 IATA Enable/Disable Disable 122 IATA Check Character Transmission Enable 122 Disable 123 Don’t Calculate 123 Send 124 Transmit 124 abcd/abcd 125 Codabar Start/Stop Character Match Don’t Require Match 125 Codabar Quiet Zones Small Quiet Zones on two sides 126 Variable 126 Codabar Set Length 1 3 127 Codabar Set Length 2 50 128 Disable 129 Disable 129 Static 129 200 msec
PAGE 272
Standard Defaults Parameter Default Your Setting Page Number GS1 DataBar™ Omnidirectional GS1 DataBar™ Omnidirectional Enable/ Disable Disable 137 GS1 DataBar™ Omnidirectional GS1-128 Emulation Disable 137 2D component not required 138 GS1 DataBar™ Expanded Enable/Disable Disable 138 GS1 DataBar™ Expanded GS1-128 Emulation Disable 139 GS1 DataBar™ Expanded 2D Component 2D component not required 139 GS1 DataBar™ Expanded Length Control Variable 140 GS1 DataBar™ Expanded Set Length 1
PAGE 273
Standard Defaults Parameter Default Your Setting Page Number MSI Check Character Transmission Enable 150 MSI Length Control Variable 152 MSI Set Length 1 1 152 MSI Set Length 2 50 153 Disable 154 Enable Plessey std. check char.
PAGE 274
Standard Defaults Parameter Default Your Setting Page Number Maxicode Primary Message Transmission Disable 171 Maxicode Length Control Variable 172 Maxicode Set Length 1 1 172 Maxicode Set Length 2 0145 173 PDF417 Enable / Disable Enable 174 PDF417 Length Control Variable 174 PDF417 Set Length 1 1 175 PDF417 Set Length 2 2,710 176 Disable 177 Micro PDF AIM ID and label type 177 Variable 178 Micro PDF417 Set Length 1 1 178 Micro PDF417 Set Length 2 0366 179 QR Code Ena
PAGE 275
Standard Defaults Parameter Default Your Setting Page Number Disconnect Beep Enable 194 Docking Beep Enable 195 Leash Alarm Disable 195 Automatic Configuration Update Enable 197 Copy Configuration to Scanner N/A 197 Copy Configuration to Base Station N/A 197 Batch Mode Disable 198 Send Batch N/A 198 Erase Batch Memory N/A 199 No Delay 199 Unlink Label Required 200 Do not include 201 No Delimiter Character 202 2 Seconds 202 Disable 203 Select PIN Code Length 4-char
PAGE 276
Standard Defaults NOTES 266 HP Wireless Barcode Scanner
PAGE 277
Appendix C Sample Barcodes The sample barcodes in this appendix are typical representations for their symbology types.
PAGE 278
Sample Barcodes Sample Barcodes (continued) Code 32 Codabar 13579 Code 93 Code 11 123456789 268 HP Wireless Barcode Scanner
PAGE 279
Sample Barcodes GS1 DataBar™ (RSS) GS1 DataBar™ variants must be enabled to read the barcodes below (see GS1 DataBar™ Omnidirectional on page 137).
PAGE 280
Sample Barcodes 2D Barcodes Aztec Datamatrix China Sensible Code MaxiCode PDF 417 Micro PDF 417 ABCabc BV17453 QR Code Micro QR Code 123456 35900G9 UCC Composite 270 HP Wireless Barcode Scanner
PAGE 281
Appendix D Keypad Use the barcodes in this appendix to enter numbers as you would select digits/characters from a keypad.
PAGE 282
Keypad 272 A B C D E F HP Wireless Barcode Scanner
PAGE 283
Appendix E Scancode Tables Control Character Emulation Control character emulation selects from different scancode tables as listed in this appendix. Each of the control character sets below are detailed by interface type in the tables. These apply to USB Keyboard platforms. Control Character 00 : Characters from 00 to 0x1F are sent as control character Ctrl+Keys, special keys are located from 0x80 to 0xA1.
PAGE 284
Interface type USB-Keyboard Alt Mode Table 52.
PAGE 285
Interface type USB-Keyboard Alt Mode (continued) Table 53.
PAGE 286
IBM XT Table 54. Scancode Set When Control Character is 00 or 01 0x 1x X0 NULL C+@ DLE C(S)+P x1 SOH C(S)+A DC1 C(S)+Q x2 STX C(S)+B DC2 C(S)+R x3 ETX C(S)+C DC3 C(S)+S x4 EOT C+D DC4 C(S)+T x5 ENQ C(S)+E NAK C(S)+U x6 ACK C(S)+F SYN C(S)+V x7 BEL C(S)+G ETB C(S)+W x8 BS C(S)+H CAN C(S)+X x9 HT TAB EM C(S)+Y xA LF C(S)+J SUB C(S)+Z xB VT C(S)+K ESC Esc xC FF C(S)+L FS C(S)+\ xD CR Enter GS C+] xE SO C(S)+N RS C(S)+^ xF SI C(S)+O US C(S)+_ 2x Space ! “ # $ % & ‘ ( ) * + , - .
PAGE 287
Scancode Tables Microsoft Windows Codepage 1252 Windows-1252 is a character encoding of the Latin alphabet, used by default in the legacy components of Microsoft Windows in English and some other Western languages.
PAGE 288
Scancode Tables NOTES 278 HP Wireless Barcode Scanner
PAGE 289
ASCII Chart ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No. NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F SP ! “ # $ % & ’ ( ) * + , .
PAGE 290