HP EliteBook Folio 9480m Notebook PC Maintenance and Service Guide
© Copyright 2014–2016 HP Development Company, L.P. AMD is a trademark of Advanced Micro Devices, Inc. Bluetooth is a trademark owned by its proprietor and used by HP Inc. under license. Intel, Celeron, and Pentium are trademarks of Intel Corporation in the U.S. and other countries. Microsoft and Windows are trademarks of the Microsoft group of companies. The information contained herein is subject to change without notice.
Important Notice about Customer Self-Repair Parts CAUTION: Your computer includes Customer Self-Repair parts and parts that should only be accessed by an authorized service provider. See Chapter 5, "Removal and replacement procedures for Customer Self-Repair parts," for details. Accessing parts described in Chapter 6, "Removal and replacement procedures for Authorized Service Provider only parts," can damage the computer or void your warranty.
iv Important Notice about Customer Self-Repair Parts
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation.
vi Safety warning notice
Table of contents 1 Product description ....................................................................................................................................... 1 2 External component identification .................................................................................................................. 5 Display .................................................................................................................................................................... 5 Top ..
Hard drive cover ................................................................................................................................ 32 Hard drive/SSD drive ......................................................................................................................... 33 mSATA drive ....................................................................................................................................... 35 RTC battery ......................................................
8 Computer Setup (BIOS) and MultiBoot in Windows 8 ....................................................................................... 78 Using Computer Setup ......................................................................................................................................... 78 Starting Computer Setup .................................................................................................................. 78 Navigating and selecting in Computer Setup .......................
Using Windows 7 operating system media ....................................................................................... 93 12 Backup and recovery in Windows 8 .............................................................................................................. 95 Backing up your information ............................................................................................................................... 95 Performing a system recovery ............................................
Display ............................................................................................................................................................... 115 Index ...........................................................................................................................................................
xii
1 Product description Category Description Product Name HP EliteBook Folio 9480m Notebook PC Processors Intel® Core® processors: ● i7-4650U 1.7-GHz (max turbo frequency 3.3-GHz), 4-MB L3 Cache, 15W ● i7-4600U 2.1-GHz (max turbo frequency 3.3-GHz), 4-MB L3 Cache, 15W ● i5-4310U 2.0-GHz (max turbo frequency 3.0-GHz), 3-MB L3 Cache, 15W ● i5-4210U 1.7-GHz (max turbo frequency 2.
Category Description Audio and video Two stereo speakers HD audio with DTS Studio Sound Integrated 720p HD webcam (supports no camera option) Integrated dual-array microphone Ethernet Intel I1218LM 10/100/1000 Ethernet network interface card (NIC) with iAMT NIC Power Down technology S3/S4/S5 wake on LAN Wireless Integrated wireless local area network (WLAN) options by way of wireless module Two WLAN antennas built into display assembly Support for the following WLAN formats: ● Intel Dual Band Wirele
Category Description VGA (Dsub 15 pin) supporting: 1920×1200 external resolution @ 60 Hz, hot plug and unplug and auto-detection for correct output to wide-aspect vs.
Category Description ● FreeDOS ● Ubuntu Linux Restore media ● DRDVD Windows 7 ● DRDVD Windows 8.1 ● SRDVD Ubuntu ● Windows 7 Professional 64 ● Windows 8.1 Professional 64 ● Windows 8.1 64-bit ● Windows 8.1 Country Specific 64-bit ● Windows 8.1 Emerging Market 64-bit Web-only support: Serviceability 4 Chapter 1 Product description ● Windows 10 ● Windows 10 Professional ● Windows 8.
2 External component identification Display Component Description (1) WLAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide area networks (WWAN). (3) Internal microphones (2) Record sound. (4) Webcam light (select models only) On: The webcam is in use.
Component Description NOTE: The display switch is not visible from the outside of the computer. *The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions. For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or region. To access this guide: Windows 7: Select Start > Help and Support > User Guides. Windows 8.
Lights Component (1) Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state, a power-saving state. The computer shuts off power to the display and other unneeded components. ● Off: The computer is off or in Hibernation. Hibernation is a power-saving state that uses the least amount of power. NOTE: For select models, the Intel® Rapid Start Technology feature is enabled at the factory.
Buttons, speakers, and fingerprint reader (select models only) Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component Description – or – Right-click the Start button, and then select Power Options. (2) Wireless button Turns the wireless feature on or off but does not establish a wireless connection. (3) Volume mute button Mutes and restores speaker sound. (4) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a password logon. Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key.
Component (5) Description Embedded numeric keypad When the keypad is turned on, it can be used like an external numeric keypad. Each key on the keypad performs the function indicated by the icon in the upper-right corner of the key. (6) Windows applications key Windows 7: Displays a shortcut menu for items beneath the cursor. Windows 8.1: Displays options for a selected object. Windows 10: Displays options for a selected object.
Component Description the battery reaches a critical battery level, the battery light begins blinking rapidly. (4) Hard drive light ● Off: The battery is fully charged. ● Blinking white: The hard drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. Left Component Description (1) Power connector Connects an AC adapter. (2) Vent Enables airflow to cool internal components.
Component Description NOTE: Windows 7: Select Start > Help and Support > User Guides. Windows 8.1: From the Start screen, type support, and then select the HP Support Assistant app. ‒ or – From the Windows desktop, click the question mark icon in the notification area, at the far right of the taskbar. Windows 10: Select Start, select All apps, select HP Help and Support, and then select HP Documentation. NOTE: When a device is connected to the jack, the computer speakers are disabled.
Bottom Component (1) Description Wireless and memory module compartment Contains the wireless and memory modules. CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact support through HP Support Assistant.
Component 14 Description (4) Speakers (2) Produce sound. (5) Hard drive bay Contains the hard drive. (6) Battery release latch Releases the battery from the battery bay. (7) Battery bay and SIM slot Holds the battery. Supports a wireless subscriber identity module (SIM). The SIM slot is located inside the battery bay.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer. IMPORTANT: Check the following locations for the labels described in this section: the bottom of the computer, inside the battery bay, under the service door, or on the back of the display. ● Service label—Provides important information to identify your computer.
3 Illustrated parts catalog NOTE: HP continually improves and changes product parts. For complete and current information on supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then follow the on-screen instructions. NOTE: Details about your computer, including model, serial number, product key, and length of warranty, are on the service tag at the bottom of your computer. See Illustrated parts catalog on page 16 for details.
Computer major components Computer major components 17
Item Component (1) Display assembly: The display assembly is spared at the subcomponent level only. For more display assembly spare part information, see Display assembly subcomponents on page 20. (2) Keyboard (backlit; includes keyboard cable and pointing stick cable): NOTE: (3) Spare part number 785648-xx1 For a list of keyboard country codes, see Keyboard on page 45.
Item (17) (18) (19) (20) (21) Component Spare part number HP Intel Dual Band Wireless-N 7260AN 802.11 a/b/g/n (2x2) combination WiFi and Bluetooth 4.0 WLAN module 717379-001 HP Intel Dual Band Wireless-N 7260AN 802.11 a/b/g/n (2x2) combination WiFi and Bluetooth 4.
Display assembly subcomponents Item Component (1) Display bezel: (2) 20 For use on models with a webcam 769705-001 For use on models without a webcam 769706-001 Webcam/microphone module 769710-001 Microphone module 702873-001 Display Hinge Kit (includes left and right display hinges and left and right hinge covers) 702857-001 (3a) Display hinge covers (2) (3b) Display hinges (4) 35.6-cm (14.
Item Component Spare part number (5b) WLAN antenna cables and transceivers (6) Display enclosure 748350-001 Display Panel Support Kit (includes WLAN antenna cables and transceivers, WWAN antenna cables and transceivers, and display enclosure) 769709-001 Mass storage devices Item Description (1) Hard drive (does not include hard drive bracket or screws): Spare part number 500-GB, 7200-rpm, 7-mm, SED 703268-001 500-GB, 7200-rpm, 7-mm 703267-001 Solid-State Drive (includes drive bracket, co
Item Description (2c) Drive connector (3) Solid-state drive, M.2: Spare part number 120-GB, M.2 769712-001 32-GB, M.2 769711-001 Hard Drive Hardware Kit (not illustrated), includes: 702870-001 Hard drive connector Hard drive bracket Hard drive bracket screws Miscellaneous parts Component Spare part number AC adapter: 45-W HP Smart AC adapter, 7.
Component Spare part number For use in the United Kingdom and Singapore 490371-031 For use in the United States 490371-001 Power cord (3-pin, black, 1.
4 Removal and replacement procedures preliminary requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screw driver ● Magnetic screw driver ● Phillips P0 and P1 screw drivers Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.
Drive handling CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a drive, or loss of information, observe these precautions: Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Before handling a drive, be sure that you are discharged of static electricity.
Typical electrostatic voltage levels Relative humidity Event 26 10% 40% 55% Walking across carpet 35,000 V 15,000 V 7,500 V Walking across vinyl floor 12,000 V 5,000 V 3,000 V Motions of bench worker 6,000 V 800 V 400 V Removing DIPS from plastic tube 2,000 V 700 V 400 V Removing DIPS from vinyl tray 11,500 V 4,000 V 2,000 V Removing DIPS from Styrofoam 14,500 V 5,000 V 3,500 V Removing bubble pack from PCB 26,500 V 20,000 V 7,000 V Packing PCBs in foam-lined box 21,000 V
Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations. ● Place items on a grounded surface before removing items from their containers.
Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
5 Removal and replacement procedures for Customer Self-Repair parts CAUTION: The Customer Self-Repair program is not available in all locations. Installing a part not supported by the Customer Self-Repair program may void your warranty. Check your warranty to determine if Customer Self-Repair is supported in your location. NOTE: HP continually improves and changes product parts. For complete and current information on supported parts for your computer, go to http://partsurfer.hp.
3. Slide the battery outward (2), lift the outer edge of the battery (3), and then remove it from the computer (3). When installing the battery: 1. Insert the battery connector end of the battery into the bay, aligning it to the left edge. 2. Slide the battery into the bay until it drops and the latch snaps, and then slide the latch to the left to lock the battery. NOTE: In the locked position there will be no red color shown in the latch slot.
2. Remove the SIM (2) from the SIM slot. Reverse this procedure to install the SIM.
Hard drive cover NOTE: The hard drive cover is available in the Plastics kit, spare part number 702877-001. Description Spare part number Plastics kit 702877-001 Before removing the hard drive cover, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3.
Hard drive/SSD drive NOTE: The hard drive spare part kit does not include the hard drive bracket, connector, or screws. The solid-state drive spare part kit includes the Hard Drive Hardware Kit, which includes the bracket, connector, and screws..
3. Lift the hard drive, and then pull the hard drive out of the hard drive bay. 4. If it is necessary to disassemble the hard drive, perform the following steps: a. Remove the connector from the hard drive (1). b. Remove the four Phillips PM3.0×4.0 screws (2) that secure the hard drive bracket to the hard drive. c. Remove the hard drive bracket (3) from the hard drive. The hard drive bracket, connector, and screws are available in the Hard Drive Hardware Kit, spare part number 702870-001.
mSATA drive Description Spare part number 120-GB drive, M.2 769712-001 32-GB drive, M.2 769711-001 Before removing the mSATA drive follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4.
2. Remove the drive (2) by pulling it away from the slot at an angle. NOTE: mSATA drives are designed with a notch to prevent incorrect insertion. Reverse this procedure to install the mSATA drive.
RTC battery Description Spare part number RTC battery (includes cable and double-sided tape) 702853-001 Before removing the RTC battery, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4.
Service cover Description Spare part number Service cover 704441-001 Service door (RCTO) 713547-001 Before removing the service cover, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4.
Memory module NOTE: Primary and expansion memory is installed in a stacked configuration in the bottom of the computer. Description Spare part number 4-GB memory module (PC3L, 12800, 1600-MHz) 691740-001 8-GB memory module (PC3L, 12800, 1600-MHz) 693374-001 Update BIOS before adding memory modules Before adding new memory, make sure you update the computer to the latest BIOS.
2. Remove the memory module (2) by pulling the module away from the slot at an angle. NOTE: Memory modules are designed with a notch to prevent incorrect insertion into the memory module slot. NOTE: The computer uses two memory slots. The top slot houses the expansion memory module and the bottom slot houses the primary memory module. Reverse this procedure to install a memory module.
WWAN module NOTE: The WWAN module and the WLAN module are not interchangeable. Description Spare part number HP lt4112 LTE/HSPA+ Mobile Broadband Module 740011-001 HP lt4211 LTE/EV-DO/HSPA+ Gobi 4G Module 793116-001 HP hs3110 HSPA+ Mobile Broadband Module 822828-001 Before removing the WWAN module, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
3. Remove the WWAN module (3) by pulling the module away from the slot at an angle. NOTE: WWAN modules are designed with a notch to prevent incorrect insertion. NOTE: If the WWAN antennas are not connected to the terminals on the WWAN module, the protective sleeves must be installed on the antenna connectors, as shown in the following illustration. Reverse this procedure to install the WWAN module.
WLAN module Description Spare part number Intel Dual Band Wireless-AC 7260 802.11 AC 2x2 WiFi + BT 4.0 Combo Adapter 710663-001 HP Intel Dual Band Wireless-N 7260AN 802.11 a/b/g/n (2x2) combination WiFi and Bluetooth 4.0 WLAN module 717379-001 Intel Dual Band Wireless-N 7260AN 802.11 a/b/g/n (2x2) combination WiFi and Bluetooth 4.
3. Remove the WLAN module (3) by pulling the module away from the slot at an angle. NOTE: WLAN modules are designed with a notch to prevent incorrect insertion. NOTE: If the WLAN antennas are not connected to the terminals on the WLAN module, the protective sleeves must be installed on the antenna connectors, as shown in the following illustration. Reverse this procedure to install the WLAN module.
Keyboard In this section, the first table provides the main spare part number for the keyboard. The second table provides the country codes.
46 2. Rest and secure the computer on its right side. 3. Partially open the computer. 4. Insert a screw driver or similar thin tool into the keyboard release opening near the fan, and then press on the back of the keyboard until the keyboard disengages from the computer. 5. Turn the computer right-side up with the front toward you.
6. Lift the rear edge of the keyboard (1), and then swing the keyboard up and forward (2) until it rests upside down on the palm rest (3). 7. Release and disconnect the following connectors and cables: ● Release the pointing stick connector (1) and remove the cable (2). ● Release the large keyboard connector (3) and remove the cable (4). ● Release the small keyboard connector (5) and remove the cable (6).
8. Remove the keyboard. Reverse this procedure to install the keyboard.
6 Removal and replacement procedures for Authorized Service Provider parts CAUTION: Components described in this chapter should only be accessed by an authorized service provider. Accessing these parts can damage the computer or void the warranty. NOTE: HP continually improves and changes product parts. For complete and current information on supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then follow the on-screen instructions.
Display assembly components (panel, bezel, webcam, microphone) All display assemblies include WLAN antenna transceivers and cables. WWAN models also include 2 WWAN antenna transceivers and cables. Full hinge-up displays are not spared. This section describes removing components that do not require that you entirely remove the display assembly from the computer. You can remove the display bezel, webcam/microphone module, and display panel with the display assembly still attached to the computer.
b. 4. 5. Remove the display bezel (4). The display bezel is available using spare part number 769705-001 on models with a webcam and 769706-001 on models without a webcam. If it is necessary to replace the webcam/microphone module: a. Detach the webcam/microphone module (1) from the display enclosure. (The webcam/microphone module is attached to the display enclosure with double-sided tape.) b. Disconnect the cable (2) from the webcam/microphone module. c. Remove webcam/microphone module.
b. Rotate the top of the display panel downward (1). c. Lift the tape that secure the display cable connector on the panel (2), and then disconnect the cable (3) from the connector (4). Reverse this procedure to reassemble and install the display assembly components.
Base enclosure Description Spare part number Base enclosure 702863-001 Before removing the base enclosure, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4.
54 3. Remove the 13 Torx PM2.0×5.0 screws that secure the base enclosure to the computer. 4. Remove the 7 Torx PM2.0×3.0 screws from the battery bay that secure the base enclosure to the computer.
5. Lift the base enclosure (1) off the computer while threading the antenna cables through the hole in the base enclosure (2). Reverse this procedure to install the base enclosure. Touchpad Before removing the touchpad, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3.
2. Lift the touchpad from the computer (2). 3. Remove the touchpad. Reverse this procedure to install the touchpad. NOTE: When replacing the touchpad, make sure to install the screws into holes closer to the edge of computer.
Power connector Description Spare part number Power connector 702875-001 Before removing the power connector, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4.
Fan Description Spare part number Fan (includes cable) 702859-001 Before removing the fan, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 29). a.
System board NOTE: The system board spare part kit includes replacement thermal material. All system boards use the following part numbers: xxxxxx-001: Windows 7 or non-Windows operating systems xxxxxx-501: Windows 8.1 Standard operating system xxxxxx-601: Windows 8.
60 ● (3): Left speaker cable ● (4): Touchpad ● (5): Smart card reader 2. Remove the 2 Phillips PM2.0×4.0 screws that secure the system board to the computer. 3. Lift the left side of the system board up at an angle (1).
4. Pull the system board away from and out of the computer (2), making sure the connectors on the right side of the board (3) are clear of the computer. NOTE: To avoid breaking the board, support the right side of the system board near the heat sink (3) as you lift it up and out of the computer. Reverse this procedure to install the system board.
Heat sink NOTE: The heat sink spare part kit includes replacement thermal material. Description Spare part number Heat sink 769708-001 Before removing the heat sink, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4.
2. Remove the heat sink (2). NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system board components each time the heat sink is removed. Replacement thermal material is included with the heat sink, processor, and system board spare part kits. The following illustration shows the replacement thermal material locations. Thermal paste is used on the heat sink (1) and the processor (2). Reverse this procedure to install the heat sink.
Speaker assembly Description Spare part number Speaker assembly (includes cable) 702869-001 Before removing the speaker assembly, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4.
Smart card board Description Spare part number Smart card board (includes cable) 769707-001 Before removing the smart card reader, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4.
Fingerprint reader board Description Spare part number Fingerprint reader board (includes cable) 702845-001 Before removing the fingerprint reader board, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4.
Display assembly This section describes removing components that require you to completely remove the display panel. For more information about removing display components that do not require that you remove the assembly from the computer, see Display assembly components (panel, bezel, webcam, microphone) on page 50. NOTE: The display assembly is spared at the subcomponent level only. Before removing the display assembly, follow these steps: 1. Turn off the computer.
NOTE: Be sure to support the display when removing the screws. 4. Remove the four Phillips PM2.5×4.0 screws (1) that secure the display assembly to the computer. 5. Remove the display assembly from the top cover (2). 6. To remove the display bezel: a. Flex the inside edges of the bottom edge (1), the left and right sides (2), and the top edge (3) of the display bezel until the bezel disengages from the display enclosure. b. Remove the display bezel (4).
7. To remove the display panel: NOTE: For this procedure the display will not be connected to the computer as shown in the following images. a. Remove the four Phillips PM2.0×3.0 screws that secure the display panel to the display enclosure. Display panels are available using the following spare part numbers: b. ● 769721-001 — 35.6-cm (14.0-in), LED, HD, AntiGlare display panel ● 769722-001 — 35.6-cm (14.0-in), LED, HD+, AntiGlare display panel Rotate the top of the display panel downward (1).
c. Lift the tape that secure the display cable connector on the panel (2), and then disconnect the cable (3) from the connector (4). NOTE: For this procedure the display will not be connected to the computer as shown in the following image. 8. If it is necessary to replace the display hinges: Display hinge covers and hinges are available in the Display Hinge Kit, spare part number 702857-001. 70 a. Remove the Phillips broadhead PM2.0×2.
9. c. Remove the 2 broadhead Phillips PM2.0×2.5 screws (1) that secure each display hinge to the display enclosure. d. Lift the display hinges off the display enclosure (2). If it is necessary to replace the WLAN antenna cables and transceivers: WLAN and WWAN antennas are available in the Antenna Kit, spare part number 769704-001. a. Release the WLAN antenna transceivers (1) from the clips built into the display enclosure.
10. If it is necessary to replace the WWAN antenna cables and transceivers: WLAN and WWAN antennas are available in the Antenna Kit, spare part number 769704-001. a. Release the WWAN antenna transceivers (1) from the clips built into the display enclosure. (The WWAN antenna transceivers are attached to the display enclosure with double-sided tape.) b. Detach the WWAN antenna cables from the routing channels (2) built into the display enclosure. c. Remove the WWAN antenna cables and transceivers.
7 Computer Setup (BIOS) and MultiBoot in Windows 7 Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Restoring factory settings in Computer Setup NOTE: Restoring defaults will not change the hard drive mode.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. Downloading a BIOS update CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do not download or install a BIOS update while the computer is running on battery power, docked in an optional docking device, or connected to an optional power source.
optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly. NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the boot order. You can change the order in which the computer searches for a boot device by changing the boot order in Computer Setup.
Setting a MultiBoot Express prompt To start Computer Setup and set the computer to display the MultiBoot startup location menu each time the computer is started or restarted, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Use a pointing device or the arrow keys to select System Configuration > Boot Options, and then press enter. 4.
8 Computer Setup (BIOS) and MultiBoot in Windows 8 Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Restoring factory settings in Computer Setup NOTE: Restoring defaults will not change the hard drive mode.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. Downloading a BIOS update CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do not download or install a BIOS update while the computer is running on battery power, docked in an optional docking device, or connected to an optional power source.
Using MultiBoot About the boot device order As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly.
To move the device down in the boot order, use a pointing device to click the down arrow, or press the key. 5. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Dynamically choosing a boot device using the f9 prompt To dynamically choose a boot device for the current startup sequence, follow these steps: 1.
9 Computer Setup (BIOS), TPM, and HP Sure Start in Windows 10 Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes: Select the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Select Main, select Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Select the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
Updating the BIOS Updated versions of the BIOS may be available on the HP website. Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file. Determining the BIOS version To decide whether you need to update Computer Setup (BIOS), first determine the BIOS version on your computer.
NOTE: If you connect your computer to a network, consult the network administrator before installing any software updates, especially system BIOS updates. BIOS installation procedures vary. Follow any instructions that are revealed on the screen after the download is complete. If no instructions are revealed, follow these steps: 1. Type file in the taskbar search box, and then select File Explorer. 2. Select your hard drive designation. The hard drive designation is typically Local Disk (C:). 3.
Using HP Sure Start (select products only) Select computer models are configured with HP Sure Start, a technology that continuously monitors the computer's BIOS for attacks or corruption. If the BIOS becomes corrupted or is attacked, HP Sure Start automatically restores the BIOS to its previously safe state, without user intervention. HP Sure Start is configured and already enabled so that most users can use the HP Sure Start default configuration.
10 HP PC Hardware Diagnostics (UEFI) HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run diagnostic tests to determine whether the computer hardware is functioning properly. The tool runs outside the operating system so that it can isolate hardware failures from issues that are caused by the operating system or other software components.
Download any version of UEFI for a specific product: 1. Go to http://www.hp.com/support, and then select your country. The HP Support page is displayed. 2. Click Drivers & Downloads. 3. In the text box, enter the product name, and then click Go. – or – Click Find Now to let HP automatically detect your product. 4. Select your computer, and then select your operating system. 5. In the Diagnostic section, follow the on-screen instructions to select and download the UEFI version you want.
11 Backup and recovery in Windows 7 Your computer includes HP and Windows tools to help you safeguard your information and retrieve it if you ever need to. These tools along with an optional external hard drive, a network drive, or an optional external optical drive will help you return your computer to a proper working state, all with simple steps.
applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery DVDs: ● Windows 7 operating system DVD—Installs the operating system without additional drivers or applications. ● Driver Recovery DVD—Installs specific drivers and applications only, in the same way that the HP Software Setup utility installs drivers and applications. Creating recovery media NOTE: The Windows 7 operating system DVD can be created only once.
To create a backup using Windows Backup and Restore: NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or create system repair media (select models only).
1. If possible, back up all personal files. 2. If possible, check for the presence of the Windows partition. To check for the Windows partition, select Start > Computer. NOTE: If the Windows partition is not listed, you must recover your operating system and programs using the Windows 7 operating system DVD and the Driver Recovery media. For additional information, see Using Windows 7 operating system media on page 93. 3.
To initiate recovery using a Windows 7 operating system DVD: NOTE: This process takes several minutes. 1. If possible, back up all personal files. 2. Restart the computer, and then insert the Windows 7 operating system DVD into the optical drive before the Windows operating system loads. 3. When prompted, press any keyboard key. 4. Follow the on-screen instructions. 5. Click Next. 6. Select Repair your computer. 7. Follow the on-screen instructions. After the repair is completed: 94 1.
12 Backup and recovery in Windows 8 To protect your information, use Windows backup and restore utilities to back up individual files and folders, back up your entire hard drive, create system repair media (select models only) by using an optional external optical drive, or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer. From the Start screen, type restore, click Settings, and then select from the list of displayed options.
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery. 1. If possible, back up all personal files. 2. If possible, check for the presence of the Recovery Image partition and the Windows partition.
Using Windows operating system media (purchased separately) To order a Windows operating system DVD, contact support. See the Worldwide Telephone Numbers booklet included with the computer. You can also find contact information from the HP website. Go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. CAUTION: Using a Windows operating system media completely erases hard drive contents and reformats the hard drive.
13 Backup and recovery in Windows 10 This chapter provides information about the following processes. The information in the chapter is standard procedure for most products. ● Creating recovery media and backups ● Restoring and recovering your system For additional information, refer to the HP support assistant app. ▲ Type support in the taskbar search box, and then select the HP Support Assistant app. ‒ or – Click the question mark icon in the taskbar.
You can use Windows tools to create system restore points and create backups of personal information, see Using Windows tools on page 99. ● If your computer does list the Recovery partition and the Windows partition, you can use HP Recovery Manager to create recovery media after you successfully set up the computer. HP Recovery media can be used to perform system recovery if the hard drive becomes corrupted.
Restore and recovery There are several options for recovering your system. Choose the method that best matches your situation and level of expertise: IMPORTANT: ● Windows offers several options for restoring from backup, refreshing the computer, and resetting the computer to its original state. For more information see the Get started app. ▲ ● Not all methods are available on all products. Select the Start button, and then select the Get started app.
website. Go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. IMPORTANT: HP Recovery Manager does not automatically provide backups of your personal data. Before beginning recovery, back up any personal data you want to retain. Using HP Recovery media, you can choose from one of the following recovery options: NOTE: Only the options available for your computer display when you start the recovery process.
Changing the computer boot order If your computer does not restart in HP Recovery Manager, you can change the computer boot order, which is the order of devices listed in BIOS where the computer looks for startup information. You can change the selection to an optical drive or a USB flash drive. To change the boot order: IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before beginning these steps. 1. Insert the HP Recovery media. 2.
Removing the HP Recovery partition (select products only) HP Recovery Manager software allows you to remove the HP Recovery partition to free up hard drive space. IMPORTANT: After you remove the HP Recovery partition, you will not be able to perform System Recovery or create HP recovery media from the HP Recovery partition. So before you remove the Recovery partition, create HP Recovery media; see Creating HP Recovery media (select products only) on page 98.
14 Specifications Computer specifications Metric U.S. Width 33.80 cm 13.3 in Depth 23.13 cm 9.09 in Height (front to back) 1.95 cm 0.77 in 1.63 kg 3.6 lbs Dimensions Weight Equipped with one memory module, WLAN module, and mSATA drive Input power Operating voltage and current 18.5 V dc @ 3.5 A - 65 W – or – 19.0 V dc @ 4.
35.6-cm (14.0-in) display specifications Metric U.S. Height 17.6 cm 6.93 in Width 31.2 cm 12.28 in Diagonal 35.7 cm 14.06 in Number of colors up to 16.8 million Contrast ratio 200:1 (typical) Brightness 200 nits (typical) Dimensions Pixel resolution Pitch 0.197 × 0.197 mm Format HD, SVA (1366 x 768) Configuration RGB vertical stripe Backlight LED Character display 80 × 25 Total power consumption 3.46 W Viewing angle ±65° horizontal, ±50° vertical (typical) 35.6-cm (14.
Hard drive specifications 500-GB* 320-GB* Height 7 mm 7 mm Length 100.4 mm 100.4 mm Width 69.9 mm 69.9 mm Weight 110 g 110 g Interface type SATA SATA Synchronous (maximum) 1.1 GB/sec 1.1 GB/sec Security ATA security or SED ATA security Single track 1.5 ms 1.
Solid-state drive specifications 180-GB* 256-GB* Height 7 mm 7 mm Length 100.5 mm 100.5 mm Width 69.9 mm 69.9 mm Weight 78 g 78 g Interface type ATA-7 ATA-7 Sequential Read Up to 550 MB/s Up to 460 MB/s Random Read Up to 50K IOPS Up to 46K IOPS Sequential Write Up to 520 MB/s Up to 260 MB/s Random Write Up to 80K IOPS Up to 56K IOPS Ready time, Maximum (to not busy) 2.0 s 4.0 s Logical 0.1 ms 0.
mSATA drive specifications 24-GB* 32-GB* 256-GB* Height 1 mm 1 mm 1 mm Length 50.8 mm 50.8 mm 50.8 mm Width 28.9 mm 28.9 mm 28.9 mm Weight < 10 g < 10 g < 10 g Interface type ATA-7 ATA-7 ATA-7 Sequential Read Up to 160 MB/s Up to 380 MB/s Up to 490 MB/s Random Read Up to 128 MB/s Up to 180 MB/s Up to 480 MB/s Sequential Write Up to 115 MB/s Up to 80 MB/s Up to 250 MB/s Random Write Up to 16 MB/s Up to 40 MB/s Up to 100 MB/s Ready time, Maximum (to not busy) 2.0 s 4.
15 Statement of Volatility The purpose of this document is to provide general information regarding non-volatile memory in industrystandards based HP Business Notebook PC systems and provide general instructions for restoring nonvolatile memory that can contain personal data after the system has been powered off and the hard drive has been removed. HP Business Notebook PC products that use Intel®-based or AMD®-based system boards contain volatile DDR memory.
then AMT Options. Then select Un-configure AMT on next boot. Select Save then Yes. Select the File menu, and then select Save Changes and Exit. Reboot the system and confirm that you want to un-configure AMT. 2. j. If the optional Intel® Anti-Theft Technology (AT) was activated, contact the provider to de-activate it. k. If the optional Absolute® Software Computrace® management and tracking service was activated on the notebook PC, contact the provider to deactivate it. l.
Non Volatile Memory Type Amount (Size) Does this memory store customer data? Does this memory retain data when power is removed? What is the purpose of this memory? How is data input into this memory? battery management). How is this memory write protected? on the HP website. Writing data to this ROM in an inappropriate manner can render the PC nonfunctional.
Non Volatile Memory Type Amount (Size) Does this memory store customer data? Does this memory retain data when power is removed? What is the purpose of this memory? How is data input into this memory? How is this memory write protected? public unless a firmware upgrade is necessary to address a unique issue. Fingerprint Reader 512kByte Flash Yes Yes Stores fingerprint templates. By enrolling in HP ProtectTools Security Manager.
16 Power cord set requirements The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC. The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used.
Country/region Accredited agency Applicable note number Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used. 2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor.
17 Recycling Battery When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for battery disposal. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle. Display WARNING! The backlight contains mercury.
2. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel (3). 4. Disconnect all display panel cables (1) from the display inverter and remove the inverter (2). 5. Remove all screws (1) that secure the display panel assembly to the display enclosure.
6. Remove the display panel assembly (2) from the display enclosure. 7. Position the display panel assembly upside-down. 8. Remove all screws that secure the display panel frame to the display panel. 9. Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display panel frame. 10. Remove the display panel frame (2) from the display panel. 11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward. 13. Remove the backlight cover. 14. Position the display panel right-side up. 15. Remove the backlight cables (1) from the clip (2) in the display panel. 16. Position the display panel upside-down. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury.
17. Remove the backlight frame from the display panel. 18. Remove the backlight from the backlight frame. 19. Disconnect the display panel cable (1) from the LCD panel. 20. Remove the screws (2) that secure the LCD panel to the display rear panel. 21. Release the LCD panel (3) from the display rear panel. 22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel. 24. Recycle the LCD panel and backlight.
Index A AC adapter, spare part numbers 22 AC adapter/battery light 10 antenna removal 71, 72 spare part number 20, 71, 72 Antenna Kit, spare part number 20 audio, product description 2 audio-in (microphone) jack, identifying 11 audio-out (headphone) jack, identifying 11 B Backup and Restore 92 backup tools 90 backups 98 creating 91 recovering 92 base enclosure removal 53 spare part number 18, 53 battery removal 29 spare part numbers 19, 29 battery bay, identifying 14 battery release latch 14 BIOS determinin
function keys, identifying 9 G graphics, product description 1 grounding guidelines 25 guidelines equipment 28 grounding 25 packaging 27 transporting 27 workstation 27 H Hard drive spare part numbers 33 hard drive precautions 25 product description 1 removal 33 spare part numbers 19, 21, 33 specifications 106 hard drive bay, identifying 14 hard drive bracket removal 34 hard drive cover removal 32 spare part number 32 hard drive cover, illustrated 18 Hard Drive Hardware Kit spare part number 19, 22, 33 hard
product description 2 USB 3.
TouchPad buttons 6 touchpad removal 55 TouchPad light, identifying 7 TouchPad zone identifying 6 TPM settings 86 transporting guidelines 27 travel battery connector, identifying 13 traveling with the computer 15 U USB 3.0 charging (powered) port, identifying 11 USB 3.
