User Guide
© Copyright 2014 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel is a trademark of Intel Corporation in the U.S. and other countries. AMD is a trademark of Advanced Micro Devices, Inc. Java is a U.S. trademark of Sun Microsystems, Inc. Microsoft and Windows are U.S. registered trademarks of the Microsoft group of companies. The information contained herein is subject to change without notice.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome ........................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ......................................................................................................................... 4 Right ..............
4 Navigating using the keyboard, touch gestures and pointing devices ............................................................ 23 Using pointing devices ....................................................................................................................... 23 Setting pointing device preferences ................................................................................... 23 Using the pointing stick .....................................................................................
Setting password protection on wakeup ........................................................... 36 Using battery power ........................................................................................................... 36 Finding additional battery information ............................................................... 36 Using Battery Check ......................................................................................... 37 Displaying the remaining battery charge .....................
Removing or replacing the hard drive cover ...................................................................... 49 Removing the hard drive cover ......................................................................... 49 Replacing the hard drive cover ......................................................................... 49 Replacing or upgrading the hard drive ............................................................................... 50 Removing the hard drive ...................................
Cleaning the TouchPad, keyboard, or mouse ................................................... 68 Updating programs and drivers .......................................................................................................... 68 Using SoftPaq Download Manager .................................................................................................... 68 11 Backup and recovery .....................................................................................................................
Appendix A Traveling with or shipping your computer ....................................................................................... 84 Appendix B Troubleshooting .............................................................................................................................. 85 Troubleshooting resources ................................................................................................................. 85 Resolving issues ....................................................
1 Welcome After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, see Connecting to a network on page 16. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer. For more information, see Using antivirus software on page 61.
Finding information You have already used Setup Instructions to turn on the computer and locate this guide. To locate resources that provide product details, how-to information, and more, use this table. Resources For information about Setup Instructions poster ● How to set up the computer ● Help to identify computer components Help and Support ● Operating system information To access Help and Support, select Start > Help and Support.
Resources For information about When you request a printed copy of your warranty, please include your product number, warranty period (found on your service label), name, and postal address. IMPORTANT: Do NOT return your HP product to the addresses above. For U.S. support, go to http://www.hp.com/go/ contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html.
2 Getting to know your computer Right Component (1) Description USB 3.0 ports (2) Each USB 3.0 port connects an optional USB device, such as a keyboard, mouse, external drive, printer, scanner or USB hub. NOTE: For details about different types of USB ports, see Using a USB device on page 45. 4 (2) DisplayPort Connects an optional digital display device, such as a highperformance monitor or projector.
Left Component Description (1) Power connector Connects an AC adapter. (2) Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (3) Security cable slot Attaches an optional security cable to the computer.
Display Component Description (1) WLAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide area networks (WWAN). (3) Internal microphones (2) Record sound. (4) Webcam light (select models only) On: The webcam is in use. (5) Webcam (select models only) Records video and captures photographs.
Top TouchPad Component Description (1) Pointing stick Moves the pointer and selects or activates items on the screen. (2) Left pointing stick button Functions like the left button on an external mouse. (3) TouchPad on/off button Turns the TouchPad on and off. (4) TouchPad zone Moves the pointer and selects or activates items on the screen. (5) Left TouchPad button Functions like the left button on an external mouse.
Lights Component (1) Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state, a powersaving state. The computer shuts off power to the display and other unneeded components. ● Off: The computer is off or in Hibernation. Hibernation is a power-saving state that uses the least amount of power. NOTE: For select models, the Intel® Rapid Start Technology feature is enabled at the factory.
Component Description (6) Caps lock light White: Caps lock is on, which switches the keys to all capital letters. (7) TouchPad light ● Amber: The TouchPad is off. ● Off: The TouchPad is on.
Buttons, speakers, and fingerprint reader (select models only) Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component Description (3) Volume mute button Mutes and restores speaker sound. (4) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a password logon.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, the esc key, or the b key. (3) Windows button Displays the Windows Start menu. (4) Function keys Execute frequently used system functions when pressed in combination with the fn key.
Bottom Component (1) Description Wireless and memory module compartment Contains the wireless and memory modules. (2) Travel battery connector Connects an optional travel battery. (3) Vents (2) Enable airflow to cool internal components. CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region.
Component 14 Description (6) Battery release latch Releases the battery from the battery bay. (7) Battery bay and SIM slot Holds the battery. Supports a wireless subscriber identity module (SIM). The SIM slot is located inside the battery bay.
Front Component (1) Description Wireless light White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. Amber: All wireless devices are off. (2) Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state, a power-saving state. The computer shuts off power to the display and other unneeded components. ● Off: The computer is off or in Hibernation.
3 Connecting to a network Your computer can travel with you wherever you go. But even at home, you can explore the globe and access information from millions of websites using your computer and a wired or wireless network connection. This chapter will help you get connected to that world. Connecting to a wireless network Wireless technology transfers data across radio waves instead of wires.
Select Start > All Programs > Productivity and Tools > HP Connection Manager, and then click the power button next to the desired device. Using HP Connection Manager (select models only) HP Connection Manager provides a central location for managing your wireless devices, an interface for connecting to the Internet using HP Mobile Broadband, and an interface for sending and receiving SMS (text) messages.
● A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points that can accommodate a large number of computers and accessories and can separate critical network functions. ● A home or small office WLAN typically uses a wireless router, which allows several wireless and wired computers to share an Internet connection, a printer, and files without requiring additional pieces of hardware or software.
Protecting your WLAN When you set up a WLAN or access an existing WLAN, always enable security features to protect your network from unauthorized access. WLANs in public areas (hotspots) like coffee shops and airports may not provide any security. If you are concerned about the security of your computer in a hotspot, limit your network activities to email that is not confidential and basic Internet surfing.
network service provider (called a mobile network operator), which in most cases is a cellular phone network operator. Coverage for HP Mobile Broadband is similar to cellular phone voice coverage. When used with mobile network operator service, HP Mobile Broadband gives you the freedom to stay connected to the Internet, send email, or connect to your corporate network whether you are on the road or outside the range of Wi-Fi hotspots.
7. Insert the SIM into the SIM slot, and gently push the SIM into the slot until it is firmly seated. NOTE: The SIM in your computer may look slightly different from the illustration in this section. NOTE: See the image on the battery bay to determine which way the SIM should be inserted into your computer. 8. Replace the battery. NOTE: 9. HP Mobile Broadband will be disabled if the battery is not replaced. Reconnect external power. 10. Reconnect external devices. 11. Turn on the computer.
Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network (PAN) of Bluetooth devices. For information about configuring and using Bluetooth devices, see the Bluetooth software Help. Connecting to a wired network There are 2 kinds of wired connections: local area network (LAN) and modem connection. A LAN connection uses a network cable and is much faster than a modem, which uses a telephone cable. Both cables are sold separately.
4 Navigating using the keyboard, touch gestures and pointing devices Your computer allows navigation using touch gestures (select models only) in addition to the keyboard and mouse. Touch gestures can be used on your computer TouchPad. Select computer models have special action key or hot key functions on the keyboard to perform routine tasks.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off button. Tapping To make an on-screen selection, use the Tap function on the TouchPad. ● 24 Tap one finger on the TouchPad zone to make a selection. Double-tap an item to open it.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. ● Place two fingers slightly apart on the TouchPad zone and then drag them up, down, left, or right. 2-finger pinch zoom 2-finger pinch zoom allows you to zoom out or in on images or text. ● Zoom in by placing two fingers together on the TouchPad zone and then moving your fingers apart. ● Zoom out by placing two fingers apart on the TouchPad zone and then moving your fingers together.
2-finger click 2-finger click allows you to make menu selections for an object on the screen. NOTE: Using 2-finger click is the same action as using right-click with the mouse. ● Place two fingers on the TouchPad zone and press to open the options menu for the selected object. Rotating (select models only) Rotating allows you to turn items such as photos. ● 26 Anchor the forefinger of your left hand in the TouchPad zone.
Flicking (select models only) Flicking allows you to navigate through screens or quickly scroll through documents. ● Place three fingers on the TouchPad zone and flick your fingers in a light, quick motion up, down, left or right. Using the keyboard The keyboard and mouse allow you to type select items, scroll and to perform the same functions as using touch gestures. The keyboard also allows you to use action keys and hot keys to perform specific functions.
Hot key combination fn+f4 Description Switches the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, fn+f4 alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor. Most external monitors receive video information on the computer using the external VGA video standard.
Component Description NOTE: The embedded numeric keypad will not function while an external keyboard or numeric keypad is connected to the computer. (2) Embedded numeric keypad When the keypad is turned on, it can be used like an external numeric keypad. Each key on the keypad performs the function indicated by the icon in the upper-right corner of the key. (3) num lk key Turns the embedded numeric keypad on and off when pressed in combination with the fn key.
5 Multimedia Your computer may include the following: ● Integrated speaker(s) ● Integrated microphone(s) ● Integrated webcam ● Preinstalled multimedia software ● Multimedia buttons or keys Audio On your HP computer, you can download and listen to music, stream audio content from the web (including radio), record audio, or mix audio and video to create multimedia. To enhance your listening enjoyment, attach external audio devices such as speakers or headphones.
WARNING! To reduce the risk of personal injury, lower the volume setting before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety and Environmental Notices. To access this guide, select Start > Help and Support > User guides. Checking audio functions on the computer NOTE: For best results when recording, speak directly into the microphone and record sound in a setting free of background noise.
NOTE: See Getting to know your computer on page 4 for information about your computer's video ports. VGA The external monitor port, or VGA port, is an analog display interface that connects an external VGA display device such as an external VGA monitor or a VGA projector to the computer. 1. To connect a VGA display device, connect the device cable to the external monitor port. 2.
1. Connect one end of the DisplayPort cable to the DisplayPort port on the computer. 2. Connect the other end of the cable to the digital display device. 3. Press fn+f4 to alternate the computer screen image between 4 display states: ● PC screen only: View the screen image on the computer only. ● Duplicate: View the screen image simultaneously on both the computer and the external device. ● Extend: View the screen image extended across both the computer and the external device.
6 Power management NOTE: A computer may have a power button or a power switch. The term power button is used throughout this guide to mean both types of power controls. Shutting down the computer CAUTION: Unsaved information is lost when the computer shuts down. The shutdown command closes all open programs, including the operating system, and then turns off the display and computer.
NOTE: You cannot initiate any type of networking connection or perform any computer functions while the computer is in the Sleep state. Intel Rapid Start Technology (select models only) For select models, the Intel Rapid Start Technology (RST) feature is enabled by default. Rapid Start Technology allows your computer to resume quickly from inactivity. Rapid Start Technology manages your power-saving options as follows: ● Sleep—Rapid Start Technology allows you to select the Sleep state.
NOTE: If you have set a password to be required on wakeup, you must enter your Windows password before your work will return to the screen. Using the power meter and power settings The power meter is located in the notification area, at the far right of the taskbar. The power meter allows you to quickly access power settings and view the remaining battery charge. ● To reveal the percentage of remaining battery charge and the current power plan, point over the power meter icon.
● Battery Check tool to test battery performance ● Information on calibration, power management, and proper care and storage to maximize battery life ● Information on battery types, specifications, life cycles, and capacity To access battery information: ▲ Select Start > Help and Support > Learn > Power Plans: Frequently Asked Questions. Using Battery Check Help and Support provides information on the status of the battery installed in the computer. To run Battery Check: 1.
– or – ● The power meter icon in the notification area shows a low or critical battery notification. NOTE: For additional information about the power meter, see Using the power meter and power settings on page 36. If the computer is on or in the Sleep state, the computer remains briefly in the Sleep state, and then shuts down and loses any unsaved information.
Removing a battery To remove the battery: CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and shut down the computer through Windows before removing the battery. 1. Turn the computer upside down on a flat surface, with the battery bay away from you. 2. Slide the battery release latch (1) to release the battery. 3.
NOTE: A stored battery should be checked every 6 months. If the capacity is less than 50 percent, recharge the battery before returning it to storage. Calibrate a battery before using it if it has been stored for one month or more. Disposing of a user-replaceable battery WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water. See the Regulatory, Safety and Environmental Notices for proper battery disposal.
● The computer does not turn on. ● The display does not turn on. ● The power lights are off. To test the AC adapter: NOTE: The following instructions apply to computers with user-replaceable batteries. 1. Shut down the computer. 2. Remove the battery on the computer. 3. Connect the AC adapter to the computer, and then plug it into an AC outlet. 4. Turn on the computer. ● If the power lights turn on, the AC adapter is working properly.
1. Right-click on the Windows desktop, and then select Configure Switchable Graphics. 2. Click the Power tab, and then select Switchable Graphics. Switchable graphics assigns individual applications to either Performance mode or Power Saving mode, based on power requirements. You can also manually modify the settings for an individual application by locating the application under Recent Applications drop-down menu, or by clicking Browse, located below Other Applications.
7 External cards and devices Using memory card readers Optional memory cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other computers. To determine the memory card formats that are supported on your computer, see Getting to know your computer on page 4. Inserting a memory card CAUTION: To reduce the risk of damage to the memory card connectors, use minimal force to insert a memory card. 1.
3. Press in on the card (1), and then remove it from the slot (2). NOTE: If the card does not eject, pull the card out of the slot. Using smart cards NOTE: The term smart card is used throughout this chapter to mean both smart cards and Java™ Cards. A smart card is a credit card-sized accessory that carries a microchip containing memory and a microprocessor.
Using a USB device Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Some USB devices may require additional support software, which is usually included with the device. For more information about device-specific software, see the manufacturer's instructions. These instructions may be provided with the software, on disc, or on the manufacturer’s website.
CAUTION: To reduce the risk of loss of information or an unresponsive system, use the following procedure to safely remove the USB device. 1. To remove a USB device, save your information and close all programs associated with the device. 2. Click the remove hardware icon on the Windows desktop in the notification area, at the far right of the taskbar, and then follow the on-screen instructions. 3. Remove the device.
2. Align the docking posts on the docking device with the receptors on the bottom of the computer and lower the computer into the docking device (2) until the computer is seated. 3. Push in the connect button (1) on the docking device to secure the docking device to the computer. The connect light (2) turns on when the computer is fully docked.
8 Drives Handling drives CAUTION: Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Do not drop a drive, place items on it, or expose it to liquids, or temperature or humidity extremes. Observe these precautions when handling drives: ● Before removing or installing a drive, shut down the computer. If you are unsure whether the computer is off, in the Sleep state, or in Hibernation, turn the computer on, and then shut it down.
If you add or upgrade a hard drive and intend to set a RAID volume, you must temporarily disable SRT, set the RAID volume, and then enable SRT. To temporarily disable SRT: 1. Select Start > All Programs > Intel > Intel Rapid Storage Technology. 2. Click the Acceleration link, and then click the Disable Acceleration link. 3. Wait for the Acceleration Mode to complete. 4. Click the Reset to Available link. IMPORTANT: You must temporarily disable SRT when changing RAID modes.
2. Slide the hard drive cover (2) into place, and then tighten the 2 screws (3). 3. Insert the battery (see Inserting a battery on page 38). Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation.
7. Lift the hard drive, and then pull the hard drive out of the hard drive bay. Installing a hard drive To install the hard drive: 1. Align the hard drive in the hard drive bay, and then lower the hard drive (1) into the hard drive bay until the hard drive connector is seated. 2. Tighten the 4 screws (2) to secure the hard drive. 3. Replace the hard drive cover (see Replacing the hard drive cover on page 49). 4. Insert the battery (see Inserting a battery on page 38).
5. Connect AC power and external devices to the computer. 6. Turn on the computer. Improving hard drive performance Using Disk Defragmenter As you use your computer over time, the files on the hard drive become fragmented. A fragmented drive means data on your drive is not contiguous (sequential) and, because of this, the hard drive works harder to locate files, thus slowing down the computer.
NOTE: Because solid state drives (SSDs) lack moving parts, they do not require HP 3D DriveGuard protection. NOTE: A hard drive in a primary hard drive bay or a secondary hard drive bay is protected by HP 3D DriveGuard. A hard drive installed in an optional docking device or connected to a USB port is not protected by HP 3D DriveGuard. For more information, see the HP 3D DriveGuard software Help.
9 Security Protecting the computer Standard security features provided by the Windows operating system and the non-Windows Computer Setup utility (BIOS) can protect your personal settings and data from a variety of risks. NOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. NOTE: Before you send your computer for service, back up and delete confidential files, and remove all password settings.
Passwords can be set in Windows or in the non-Windows Computer Setup utility that is preinstalled on the computer. ● BIOS administrator and DriveLock passwords are set in Computer Setup and are managed by the system BIOS. ● Automatic DriveLock passwords are enabled in Computer Setup. ● Windows passwords are set only in the Windows operating system.
Setting passwords in Computer Setup Password Function BIOS administrator password* Protects access to Computer Setup. NOTE: If features have been enabled to prevent removing the BIOS administrator password, you may not be able to remove it until those features have been disabled. DriveLock master password* Protects access to the internal hard drive that is protected by DriveLock. It is also used to remove DriveLock protection. This password is set under DriveLock Passwords during the enable process.
4. When prompted, type your current password. 5. When prompted, type your new password again to confirm. 6. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Deleting a BIOS administrator password 1.
● After DriveLock protection is applied to a hard drive, the hard drive can be accessed only by entering either the user password or the master password. ● The owner of the user password should be the day-to-day user of the protected hard drive. The owner of the master password may be either a system administrator or the day-to-day user. ● The user password and the master password can be identical.
Changing a DriveLock password To change a DriveLock password in Computer Setup, follow these steps: 1. Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Use a pointing device or the arrow keys to select Security > Hard Drive Tools > DriveLock, and then press enter. 4. Enter the BIOS Administrator password, and then press enter. 5.
Using Computer Setup Automatic DriveLock In a multiple-user environment, you can set an Automatic DriveLock password. When the Automatic DriveLock password is enabled, a random user password and a DriveLock master password will be created for you. When any user passes the password credential, the same random user and DriveLock master password will be used to unlock the drive. NOTE: A BIOS Administrator password must be set before you can access the Automatic DriveLock features.
Using antivirus software When you use the computer to access e-mail, a network, or the Internet, you potentially expose it to computer viruses. Computer viruses can disable the operating system, programs, or utilities, or cause them to function abnormally. Antivirus software can detect most viruses, destroy them, and, in most cases, repair any damage they have caused. To provide ongoing protection against newly discovered viruses, antivirus software must be kept up to date.
unauthorized access to the computer, networks, and critical data. For more information, see the HP Client Security software Help. Installing an optional security cable NOTE: A security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. NOTE: The security cable slot on your computer may look slightly different from the illustration in this section.
10 Maintenance Adding or replacing memory modules The computer has one memory module compartment. The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot. NOTE: Before adding or replacing a memory module, make sure the computer has the most recent BIOS version, and update the BIOS if needed. See Updating the BIOS on page 76.
c. 6. Tilt the door up from the computer slightly (2) and then lift the door (3) up and off the computer. If you are replacing a memory module, remove the existing memory module: a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 7. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 8. 66 To replace the memory module compartment door: a. Turn the computer upside down on a flat surface, with the memory module compartment toward you. b.
c. 9. Rotate the door down (2), and then tighten the 5 screws (3). Replace the hard drive cover (see Replacing the hard drive cover on page 49). 10. Insert the battery (see Inserting a battery on page 38). 11. Connect AC power and external devices to the computer. 12. Turn on the computer. Cleaning your computer Use the following products to safely clean your computer: ● Dimethyl benzyl ammonium chloride 0.
WARNING! To prevent electric shock or damage to components, do not attempt to clean your computer while it is turned on. ● Turn off the computer. ● Disconnect AC power. ● Disconnect all powered external devices. CAUTION: To prevent damage to internal components, do not spray cleaning agents or liquids directly on any computer surface. Liquids dripped on the surface can permanently damage internal components.
SoftPaq Download Manager works by reading and downloading, from the HP FTP site, a published database file containing computer model and SoftPaq information. SoftPaq Download Manager allows you to specify one or more computer models to determine which SoftPaqs are available for download. SoftPaq Download Manager checks the HP FTP site for updates to the database and software. If updates are found, they are downloaded and applied automatically. SoftPaq Download Manager is available on the HP website.
11 Backup and recovery Your computer includes HP and Windows tools to help you safeguard your information and retrieve it if you ever need to. These tools along with an optional external hard drive, a network drive, or an optional external optical drive will help you return your computer to a proper working state, all with simple steps.
well as select drivers and applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery DVDs: ● Windows 7 operating system DVD—Installs the operating system without additional drivers or applications. ● Driver Recovery DVD—Installs specific drivers and applications only, in the same way that the HP Software Setup utility installs drivers and applications. Creating recovery media NOTE: The Windows 7 operating system DVD can be created only once.
NOTE: Windows includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support. To access Help and Support, select Start > Help and Support. To create a backup using Windows Backup and Restore: NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1.
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery. 1. If possible, back up all personal files. 2. If possible, check for the presence of the Windows partition.
CAUTION: Using a Windows 7 operating system DVD completely erases hard drive contents and reformats the hard drive. All files that you have created and any software that you have installed on the computer are permanently removed. When reformatting is complete, the recovery process helps you restore the operating system, as well as drivers, software, and utilities. To initiate recovery using a Windows 7 operating system DVD: NOTE: This process takes several minutes. 1.
12 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Restoring factory settings in Computer Setup NOTE: Restoring defaults will not change the hard drive mode.
1. Start Computer Setup. 2. Use a pointing device or the arrow keys to select Main > System Information. 3. To exit Computer Setup without saving your changes, click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
Using MultiBoot About the boot device order As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly.
Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Dynamically choosing a boot device using the f9 prompt To dynamically choose a boot device for the current startup sequence, follow these steps: 1. Open the Select Boot Device menu by turning on or restarting the computer, and then pressing esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f9. 3.
of the operating system to isolate hardware failures from issues that may be caused by the operating system or other software components. To start HP PC Hardware Diagnostics UEFI: 1. Turn on or restart the computer, quickly press esc, and then press f2. After pressing f2, the BIOS searches three places for the HP PC Hardware Diagnostics (UEFI) tools in the following order: a.
13 Support Contacting support If the information provided in this user guide or Help and Support does not address your questions, you can contact support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician. NOTE: When support chat is not available in a particular language, it is available in English. ● E-mail support. ● Find support telephone numbers.
● Microsoft® Certificate of Authenticity label (select models only prior to Windows 8)—Contains the Windows Product Key. You may need the Product Key to update or troubleshoot the operating system. HP platforms preinstalled with Windows 8 or Windows 8.1 do not have the physical label, but have a Digital Product Key electronically installed. NOTE: This Digital Product Key is automatically recognized and activated by Microsoft Operating Systems on a reinstall of the Windows 8 or Windows 8.
14 Specifications ● Input power ● Operating environment Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz.
A Traveling with or shipping your computer If you have to travel with or ship your computer, here are some tips to keep in mind to keep your equipment safe. ● Prepare the computer for traveling or shipping: ◦ Back up your information to an external drive. ◦ Remove all discs and all external media cards, such as memory cards, from the computer. ◦ Turn off and then disconnect all external devices. ◦ Shut down the computer. ● Take along a backup of your information.
B Troubleshooting Troubleshooting resources ● Access website links and additional information about the computer through Help and Support. To access Help and Support, select Start > Help and Support. NOTE: Some checkup and repair tools require an Internet connection. HP also provides additional tools that do not require an Internet connection. ● Contact HP support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html.
change these and other power settings, right-click the Battery icon on the Windows desktop in the notification area, at the far right of the taskbar, and then click Preferences. ● The computer may not be set to display the image on the computer screen. To transfer the image to the computer screen, press fn+f4.
The wireless network connection is not working If a wireless network connection is not working as expected, follow these suggestions: ● To enable or disable a wireless or wired network device, right-click the Network Connection icon on the Windows desktop in the notification area, at the far right of the taskbar. To enable devices, select the check box from the menu option. To disable the device, clear the check box. ● Be sure that the wireless device is turned on.
The process of burning a optional external optical disc does not begin, or it stops before completion 88 ● Be sure that all other programs are closed. ● Turn off Sleep mode. ● Be sure that you are using the right kind of disc for your drive. ● Be sure that the disc is inserted properly. ● Select a slower write speed and try again.
C Electrostatic discharge Electrostatic discharge is the release of static electricity when two objects come into contact—for example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.
Index Symbols/Numerics 2-finger click TouchPad gestures 26 2-finger pinch zoom TouchPad gesture 25 A AC adapter, testing 40 AC adapter/battery light 15 administrator password 55 antivirus software 61 audio functions, checking 31 audio-in (microphone) jack, identifying 5 audio-out (headphone) jack, identifying 5 Automatic DriveLock password entering 60 removing 60 B Backup and Restore 72 backup tools 70 backups creating 71 recovering 72 battery conserving power 39 discharging 37 displaying remaining charge 3
H hard drive external 46 HP 3D DriveGuard 52 installing 51 removing 50 hard drive bay, identifying 13 hard drive light 15, 53 hard drive recovery 73 headphone (audio-out) jack 5 headphones and microphones, connecting 30 Hibernation exiting 35 initiating 35 high-definition devices, connecting 33 hot keys adjusting volume 28 battery charge 27 decrease screen brightness 28 decreasing speaker sound 28 description 27 increase screen brightness 28 increasing speaker sound 28 keyboard backlight 28 microphone mute
ports DisplayPort 4, 32 external monitor 4, 32 Intel Wireless Display 33 USB 3.
Windows applications key, identifying 12 Windows button, identifying 12 Windows Startup Repair, using 72 wireless and memory module compartment identifying 13 wireless antennas, identifying 6 wireless button 16 wireless certification label 82 wireless controls button 16 operating system 16 wireless light 8, 15, 16 wireless network (WLAN) connecting 19 corporate WLAN connection 19 equipment needed 18 functional range 19 public WLAN connection 19 security 19 using 17 WLAN antennas, identifying 6 WLAN device 1
