User's Manual Digital Satellite Receiver KSC-570
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 1 mac-4 HP LaserJet 5100 Series General Safety Warning Always follow these instructions to avoid the risk of injury to yourself or damage to your equipment. Unplug the receiver from the AC power outlet before cleaning. Use only a damp cloth for cleaning the exterior of the receiver. Do not use accessories or attachments not recommended by the receiver manufacturer as they may cause problems to the equipment and will void the warranty.
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 2 mac-4 HP LaserJet 5100 Series T General Safety Route power supply cord so that are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to the cords that plugs in the convenience receptacles, and the point where they exit from the unit. Use an outlet that contains surge suppression or ground fault protection.
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ DIGITAL SATELLITE RECEIVER OWNER’S MANUAL SIMPLE & SPEEDY OPERATION HANDBOOK Before operation, Please read the entire manual thoroughly and retain it for future reference.
k1.
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 1 mac-4 HP LaserJet 5100 Series T Contents Remote Control Unit . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rear Panel . . . . . . . . . . . . . . . . . . . . . . .
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 2 mac-4 HP LaserJet 5100 Series T Contents Menu Transparency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Change PIN Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Parental Lock . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .
400_RCU_PVR 4/19/06 2:19 PM ˘ ` 3 mac-4 HP LaserJet 5100 Series Remote Control Unit 3 DIGITAL SATELLITE RECEIVER T
400_RCU_PVR 4/19/06 2:19 PM ˘ ` 4 mac-4 HP LaserJet 5100 Series T Remote Control Unit DIGITAL SATELLITE RECEIVER 4
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 5 mac-4 HP LaserJet 5100 Series Front Panel 1. POWER Switch the receiver power “ON” or “OFF”. 2. CH …/† ( Program … / † ) Channel Up/Down or select item of sub-menu. 3. VOL - / + ( Program Volume Up/Down or select item of sub-menu. / ) 4. OK Select a program, a highlighted line or parameter value. 5. EXIT Exit from parameter and cancel selected function. 6. MENU To see main menu. 7. SEG. DISP. 4-digit 7-segment display channel information. 8.
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 6 mac-4 HP LaserJet 5100 Series T Rear Panel 1. POWER SUPPLY 90 ~ 250V AC, 50/60Hz. 2. S/PDIF Output for connection to a digital amplifier. 3. SCART FOR VCR Connect this port to the VCR via SCART cable. 4. SCART FOR TV Connect this port to the TV via SCART cable. 5. VIDEO Video connection port to the TV or other equipment. 6. AUDIO Audio connection port to the TV or other equipment. 7. 0/12V To connect 12V to an external 0/12V switch. 8.
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 7 mac-4 HP LaserJet 5100 Series T Connecting Your Equipment How to connect your STB to various systems There are several ways of connecting the STB to your TV, VCR and/or Hi-Fi SYSTEM. Consult your local supplier for assistance in setting-up your system that is best suited to your requirements. 1. Connect STB to a TV set Connect your STB to a TV set with SCART, if your TV set is equipped for it. Alternatively you can use A/V, TV out (UHF) or S/Video jacks. 2.
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 8 mac-4 HP LaserJet 5100 Series T Connecting Your Equipment 4. Connect STB to a Digital Audio System If you have a DAC with S/PDIF coaxial cable input, you can connect the STB with it to enjoy higher quality sound. Connect S/PDIF coaxial cable to a digital amplifier. 5. Loop Through If you have another analogue or digital STB and you wish to use the same LNB then you can connect it via the loop through.
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 9 mac-4 HP LaserJet 5100 Series T Connecting Your Equipment TV with Terrestrial Antenna 1. Connect one end of RCA/Cinch cable to the RCA/Cinch jack on the back of the STB and the other end to a RCA/Cinch jack on your TV. If your TV doesn’t have a RCA/Cinch jack, connect one end of RF cable to the TV OUT on the back of the STB and the other end to a RF input jack on your TV. (To RCA/Cinch on your TV) 2.
k1.5 500 SAT(Eng) 1/5/06 5:52 PM ˘ ` 10 mac-4 HP LaserJet 5100 Series T Connecting Your Equipment Reference 1. DiSEqC 1.0 Connection All our receivers are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible. This allows multiple antennas to be connected to the STB at the same time. If you have two or more fixed antennas or LNBs then we recommend you use a DiSEqC 1.0 switch. Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 11 mac-4 HP LaserJet 5100 Series T Connecting Your Equipment Front Panel Display Message KEY & DISPLAY 11 The message of the 7-segment LED (Light-Emitting Diode) on the STB and keys are explained as below.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 12 mac-4 HP LaserJet 5100 Series T Basic Operation Basic Function 1. Program Information After the television channels have been programmed, you will see the information box each time you change the channels. 1. Every time you change channels you will receive program information for a few seconds. (In the “Banner Time” menu you can select how long this information will be shown.) 2. You may change channel lists with the UP or DOWN button.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 13 mac-4 HP LaserJet 5100 Series T Basic Operation Basic Function 4. Next-Information Banner 1. During “Channel Banner” is appearing, when you press YELLOW Button, you can get “Next-Information Banner” 2. Using “Next-Information Banner”, you can get a simple EPG of “Next-Information”. 5. Channel-Information Banner 1. During “Channel Banner” is appearing, when you press INFO(BLUE) Button, you can get “Channel-Information Banner”. 2.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 14 mac-4 HP LaserJet 5100 Series T Basic Operation Basic Function 7. Teletext / Subtitle 1. Press the RED button, popup window will be displayed on the screen. 2. Select the off, then subtitle function is off. 3. Select the Subtitle, then you can see the Subtitle language. 4. Select the Teletext, then you can see the Teletext language. 8. Timer The user can reserve a desired program at a desired time by using the Timer function. 1.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 15 mac-4 HP LaserJet 5100 Series T Basic Operation Basic Function 9. Simple Channel List 1. When you press OK( OK ) button during receiving service stream, you can get “Channel List” view. 2. Using UP/DOWN( ) buttons in “Channel List” view, you can choose another channel. 3. After moving highlight on a channel, then press OK( OK ) button. 4. Press RED button to change channel listing. 5. To get the channel sort list, press the GREEN button.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 16 mac-4 HP LaserJet 5100 Series T Menu Guide Easy Installation Before you can view the television or radio program, you must perform the installation procedure first. Therefore you will see only “Easy Installation Menu” at first when you plug in your system. The Easy Installation gives you the convenience of selecting various languages, adjusting the time and channel search. 1.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 17 mac-4 HP LaserJet 5100 Series T Menu Guide Easy Installation Language The first option is “Language Select” to select the desired language of the Menu, Audio, or Subtitle. Place the cursor on the sub menu by pressing the keys and press the OK( OK ) button to change language. The Language of Menu, Audio, or Subtitle will be changed to the selected language. Local Time You can set your local time according to your location.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 18 mac-4 HP LaserJet 5100 Series T Menu Guide Main Menu Press the MENU button on the remote control unit. You will see the “Main Menu” on the screen. 1. You can move into the desired submenu using UP/DOWN( ) buttons. 2. You should enter the PIN code in order to move into the corresponding submenu in case of “Edit Channel List or “System Setting”. 3. Press OK( OK ) button to confirm your selection. 4. Press the MENU button to return to previous menu.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 19 mac-4 HP LaserJet 5100 Series T Menu Guide Channel Search Channel Search / Installation (None, DiSEqC Switch) 1. Satellite : Select the satellite list you want using UP/DOWN( ) buttons on the satellite list. - Edit, Add, or Delete ♦ Press YELLOW button to edit, add, or delete satellite list. Pop Up menu will appear. ♦ Select mode using LEFT/RIGHT( / ) buttons. ♦ Place the cursor on satellite field and press OK( OK ) button.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 20 mac-4 HP LaserJet 5100 Series T Menu Guide Channel Search - Scan Press the RED button on the TP list. Pop up window will be displayed on the screen. ♦ Frequency : Input a proper Frequency using NUMERIC buttons. ♦ Symbol Rate : Input a proper Symbol Rate using NUMERIC buttons. ♦ Polarity : Use the LEFT/RIGHT( / ) buttons to select the Polarisation of the transponder.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 21 mac-4 HP LaserJet 5100 Series T Menu Guide Channel Search 3. C/KU Switch : You can select C/KU band by selection of switch type. 4. LNB Freq. : Select the proper LNB frequency referring to your LNB using OK( 5. C-LNB Freq. OK ) and UP/DOWN( ) buttons. : When selecting the C/KU Switch is selected as “None”, the C-LNB Freq will be dimmed automatically. Press OK( OK ) button, and then the C-LNB Freq. list will be displayed. You can also input the freq.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 22 mac-4 HP LaserJet 5100 Series T Menu Guide Channel Search Channel Search / Installation (DiSEqC 1,2) 1. Satellite : Select the satellite list you want using UP/DOWN( ) buttons on the satellite list. - Edit, Add, or Delete ♦ Press YELLOW button to edit, add, or delete satellite list. Pop Up menu will appear. ♦ Select mode using LEFT/RIGHT( / ) buttons. ♦ Place the cursor on satellite field and press OK( ) button.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 23 mac-4 HP LaserJet 5100 Series T Menu Guide Channel Search - Scan Press the RED button on the TP list. Pop up window will be displayed on the screen. ♦ Frequency : Input a proper Frequency using NUMERIC buttons. ♦ Symbol Rate : Input a proper Symbol Rate using NUMERIC buttons. ♦ Polarity : Use the LEFT/RIGHT( / ) buttons to select the Polarisation of the transponder.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 24 mac-4 HP LaserJet 5100 Series T Menu Guide Channel Search 6. 22KHz : Depending on the user’s antenna switch box or LNB. You can supply either 22KHz by setting “ON” or not by setting ”OFF”. When selecting the U-LNB 1 and U-LNB 2, the 22KHz will be dimmed. 7. 0V/12V : Depending on the user’s antenna switch box. You can choose either 0V/12V. 8. Tone Burst : Depending on the user’s antenna switch box. (“off”, “SAT A” or “SAT B”) 9.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 25 mac-4 HP LaserJet 5100 Series T Menu Guide Channel Search Channel Search / Installation (USALS) 1. Satellite : Select the satellite list you want using UP/DOWN( ) buttons on the satellite list. - Edit, Add, or Delete ♦ Press YELLOW button to edit, add, or delete satellite list. Pop Up menu will appear. ♦ Select mode using LEFT/RIGHT( / ) buttons. ♦ Place the cursor on satellite field and press OK( OK ) button.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 26 mac-4 HP LaserJet 5100 Series T Menu Guide Channel Search - Scan Press the RED button on the TP list. Pop up window will be displayed on the screen. ♦ Frequency : Input a proper Frequency using NUMERIC buttons. ♦ Symbol Rate : Input a proper Symbol Rate using NUMERIC buttons. ♦ Polarity : Use the LEFT/RIGHT( / ) buttons to select the Polarisation of the transponder.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 27 mac-4 HP LaserJet 5100 Series T Menu Guide Channel Search 7. 0V/12V : Depending on the user’s antenna switch box. You can choose either 0V/12V. 8. Tone Burst : Depending on the user’s antenna switch box. (“off”, “SAT A” or “SAT B”) 9. Longitude : Press the NUMERIC buttons and enter the Longitude. When the OK( OK ) button is pressed. It can be toggled East/West. 10. Latitude : Press the NUMERIC button and enter the Latitude.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 28 mac-4 HP LaserJet 5100 Series T Menu Guide Channel List This menu helps you to easily select the channel that you want to watch. You can see the channel list when you had searched before. To use this menu, you should set channel group you want in the Edit Channel List menu. 1. Select “Channel List” in the main menu with UP/DOWN( ) and press OK( OK ). 2. Using UP/DOWN( ) button, you can choose your channel with small-sized video view on right side.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 29 mac-4 HP LaserJet 5100 Series T Menu Guide Edit Channel List From these menus, You can create favorite lists, lock, skip, delete, or move channel. 1. Select “Edit Channel List” in the main menu with UP/DOWN( and press OK( OK ) buttons ) button. 2. At the request window, Input PIN code. If you have not entered your own PIN code, then the PIN code 0000 applies, which was set at the factory. 3. Press the SUB-T (RED) button.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 30 mac-4 HP LaserJet 5100 Series T Menu Guide Edit Channel List 1. Favorite 1 ~ 8 (Option) 1. You can edit favorite TV and Radio list. This enables you to create the 8 favorite TV and Radio lists. 2. Select the channel you want to edit favorite list and press OK( OK ) button. Note: To rename the Favorite channel, press INFO(BLUE) button. 2. Lock 1. From here you can lock channels in any of the list in order to prevent e.g. your children from watching. 2.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 31 mac-4 HP LaserJet 5100 Series T Menu Guide Edit Channel List 4. Skip 1. You can skip TV or Radio channel from the current list. 2. Select the channel you want to skip and press OK( 3. To recover the skipped channel, press the OK( OK OK ) button. ) button from edit list. 5. Move 1. You can change the position of the channel you want on the TV/Radio/All channel lists. 2. Select the channel you want to move to desired channel and press the OK( OK ) button.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 32 mac-4 HP LaserJet 5100 Series T Menu Guide Program Guide The program guide supplies information such as program listings and ending times for all available programs. 1. Select “Program Guide” in the main menu with UP/DOWN( ) buttons and press OK( OK ) button. In the viewing program, when you press the EPG button, you can get this view. Note: The Program Guide information may not be supplied by service providers. 1.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 33 mac-4 HP LaserJet 5100 Series T Menu Guide System Setting You will be asked to enter your PIN code before you can enter this menu. The PIN code preset to 0000 from the factory. The code can be changed from the “Change PIN Code” menu. Refer to page 37. If you want to customize the system to suit you better, you can specify some settings from the submenus in the “System Setting” menu. 1.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 34 mac-4 HP LaserJet 5100 Series T Menu Guide System Setting 2. Audio Language In this menu You can change default language for audio when changing services. 1. Use the UP/DOWN( ) buttons to move to language you want and then press OK( OK ) button.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 35 mac-4 HP LaserJet 5100 Series T Menu Guide System Setting 5. Screen Type If you have a TV set with the 4:3 picture format and the transmission is in 16:9, you can select 4:3 letterbox, 4:3 full screen and 16:9 full screen. 1. Select the aspect ratio of TV which is connected to STB and then press OK( OK ) button. Note 1: Fullscreen will fill up the screen but cut off some information on the left and right sides.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 36 mac-4 HP LaserJet 5100 Series T Menu Guide System Setting 8. RF Channel (option) Select this alternative if you have to change the RF channel. Select an UHF Channel you want with UP/DOWN( The RF Channel ranges from 21 to 69. ) buttons. 9. Local Time You can set your local time according to your location. 1. To set year, month and date, press UP/DOWN( ) buttons. The Calendar pop up window will be displayed. Select year using SUB-T(RED) and GREEN button.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 37 mac-4 HP LaserJet 5100 Series T Menu Guide System Setting 11. Change PIN Code From here you can change the PIN code from the standard 0000. DO NOT FORGET IT! Without it, you are not able to access to any of the functions where the code is required. You can change password for Parental Lock and Receiver Lock simultaneously. 1. Input the current PIN code using numeric button on the remote control. 2. In the highlighted new PIN code, input a new PIN code. 3.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 38 mac-4 HP LaserJet 5100 Series T Menu Guide System Setting 13. Receiver Lock If you select “On”, you will have to enter the PIN code every time you start the receiver from standby. 14. M Lock If you select “On”, you will have to enter the PIN code every time when you enter the Channel Search Menu and Channel List Menu 15. S/PDIF Output (option) You can hear digital audio of the Dolby 5.1 channel using S/PDIF Output. 1.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 39 mac-4 HP LaserJet 5100 Series T Menu Guide System Setting 16. Auto Power (option) 1. If the Auto Power is set to On and power is off, the Set turns on automatically and turns into the channel mode which you were watching before power breakdown. 2. If the Auto Power is set to Off and power is off, the Set turns into the standby mode. 17. Factory Reset Use this option only if you have to start the complete installation procedure from scratch.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 40 mac-4 HP LaserJet 5100 Series T Menu Guide Common Interface The menus are provided by the CA module and its smart card. Your receiver is equipped with two slots of Common Interface(CI), accepting both Type 1 and Type 2 PCMCIA modules(see diagram below.). Plug in the appropriate CI module together with a valid smart card. You will then have access to the respective scrambled and Pay-Per-View services.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 41 mac-4 HP LaserJet 5100 Series T Menu Guide Utility (option) 1. Game 1. Select “Game” in the Utility menu with UP/DOWN( ) buttons and press LEFT/RIGHT( / ) button. 2. Select the game you want to play and press OK( OK ) button, and then you can play the game. Tetris Hexa Puzzle Slider Mine Snake Pocker BlackJack Sokoban and etc...... 2.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 42 mac-4 HP LaserJet 5100 Series T Menu Guide Utility (option) 4. Zoom Select “Zoom” in the Utility menu with UP/DOWN( press OK( OK ) buttons and ) button, the white frame will appear. ♦ Select the size and position of video you want to expanded with RED/GREEN, LEFT/ RIGHT buttons and press OK( OK ) button, you can see the expanded video. ♦ Press EXIT button in the video only, you can see the white frame.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 43 mac-4 HP LaserJet 5100 Series T PVR Guide (Option Function) Basic Function 1. Recording 1. Pressing the RECORDING( ) button on the remote control will begin recording. 2. Pressing the STOP( ) button will stop recording. 2. Record Menu 1. When the RECORDING( ) button is pressed again during recording, the Record Menu will appear in the center of the screen. ♦ Time for Recording: This reserves the time in hours and minutes to end the Recording.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 44 mac-4 HP LaserJet 5100 Series T PVR Guide (Option Function) Basic Function 3. File List This displays the list of files that the user has saved onto the HDD. Saved files can be selected and displayed, or selected and deleted from this menu. 1. Pressing the FILE LIST( ) button will display the FILE LIST on the screen. 2. Files that the user saved will appear on the list. 3. The bottom right-hand side of the screen will display the remaining space in the HDD.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 45 mac-4 HP LaserJet 5100 Series T PVR Guide (Option Function) Basic Function 4. Fast-forward & Rewind The Fast-Forward and Rewind functions enable the user to view the front, back or any desired part of the file. 1. To view forward parts press the FF( parts press the REW( ) button and to view previous ) button on the remote control. 2. The screen will move when the relevant symbols appear on the top right-hand side of the screen. 3.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 46 mac-4 HP LaserJet 5100 Series T PVR Guide (Option Function) Basic Function 6. Slow-Motion The Slow-Motion function can be used to PLAY at a slower speed. 1. Pressing the SLOW MOTION( ) button will play the screen at a slower speed. 2. When the button is pressed again, the screen will play at an even slower speed. There are 5 different Slow-Motion speeds. 3. Press the STOP( ) button to PLAY at the recorded speed. 7. Time-Shift 1.
k1.5 500 SAT(Eng) 1/5/06 5:53 PM ˘ ` 47 mac-4 HP LaserJet 5100 Series T PVR Guide (Option Function) Basic Function 8. Instant-Replaying This function enables replaying previous parts of the current channel. 1. Pressing the QUICK REPLAY( ) button on the remote control will replay from 10 seconds before, on the current channel. Every time the QUICK REPLAY( ) button is pressed, it will skip to 10 seconds before the current time. 2.
k1.5 500 SAT(Eng) 1/5/06 5:54 PM ˘ ` 48 mac-4 HP LaserJet 5100 Series T PVR Guide (Option Function) Basic Function 9. Delayed Recording The user can record a desired program at a desired time by using the Delayed Recording function. 1. Once, Daily, Weekly Recording. ♦ Use the UP/DOWN( ), LEFT/RIGHT( / ) buttons in the Timer Setting screen to select the date and time. ♦ Press the OK( ) button to save the selected time on the Disk icon. OK The program will record at each and every selected time.
k1.5 500 SAT(Eng) 1/5/06 5:54 PM ˘ ` 49 mac-4 HP LaserJet 5100 Series Troubleshooting Problem Solution No display LED on the front panel. Power cord plug in correctly. No power supply No Picture Ensure that the STB is switched on. Check connection and correct. Check channel and video output and correct Poor picture quality Check the signal level, if this is low then try adjusting the alignment of your dish. No Sound Check the volume level of the TV and STB.
k1.
k1.
k1.
K1.