hp LaserJet-Drucker der Serie 2400 Verwendung
HP LaserJet 2400 Serie-Drucker Benutzerhandbuch
Copyright und Lizenz Marken © 2004 Copyright Hewlett-Packard Development Company, L.P. Adobe® und PostScript® sind Marken von Adobe Systems Incorporated. Vervielfältigung, Adaption oder Übersetzung sind ohne vorherige schriftliche Genehmigung nur im Rahmen des Urheberrechts zulässig. Linux ist eine in den USA eingetragene Marke von Linus Torvalds. Die Informationen in diesem Dokument können ohne Vorankündigung geändert werden.
HP Kundendienst Online-Services Wenn Sie über einen Internetzugang verfügen, können Sie rund um die Uhr auf Informationen zugreifen. World Wide Web: Aktualisierte HP Druckersoftware, Informationen zu Produkten und zur Kundenunterstützung sowie Druckertreiber in mehreren Sprachen erhalten Sie unter www.hp.com/support/lj2410, http://www.hp.com/support/lj2420, oder http://www.hp.com/ support/lj2430 (Website in englischer Sprache.
USA - Privatnutzer und Home Office: 800-752-0900 Kanada: 800-387-3154 Die Telefonnummern für andere Länder/Regionen finden Sie im Flyer, der mit dem Drucker geliefert wurde. HP Service-Informationen Anschriften von HP Partnern in den USA oder Kanada erhalten Sie unter der Rufnummer 800-243-9816 (USA) oder 800-387-3867 (Kanada). Alternativ können Sie die Website http://www.hp.com/go/cposupportguide aufrufen.
Inhaltsverzeichnis 1 Druckergrundlagen Schneller Zugriff auf Druckerinformationen ..............................................................................2 Verknüpfungen mit dem Benutzerhandbuch ......................................................................2 Hier finden Sie weitere Informationen ................................................................................2 Druckerkonfigurationen ...............................................................................................
Papierausrichtung für den beidseitigen Druck .................................................................56 Layoutoptionen für den beidseitigen Druck ......................................................................57 So führen Sie den Duplexdruck mit dem integrierten Duplexer durch .............................57 So führen Sie den manuellen Duplexdruck aus ...............................................................58 Abbrechen eines Druckauftrags ..............................................
Menüstruktur .....................................................................................................................87 Konfigurationsseite ...........................................................................................................87 Verbrauchsmaterial-Statusseite .......................................................................................89 PS- oder PCL-Schriftartenliste .........................................................................................
Fehlerbehebung bei allgemeinen Druckproblemen ..............................................................146 Fehlerbehebung bei häufiger auftretenden Windows-Problemen ........................................147 Fehlerbehebung von häufiger auftretenden Macintosh-Problemen .....................................149 Fehlersuche bei häufiger auftretenden PostScript-Problemen .............................................155 Allgemeine Probleme ...................................................................
So überprüfen Sie, ob DIMM-Module oder CompactFlash-Karten ordnungsgemäß installiert sind ...................................................................................206 Speichern von Ressourcen (permanente Ressourcen) ........................................................207 Installieren einer EIO-Karte ...................................................................................................208 So installieren Sie eine EIO-Karte ...........................................................
x DEWW
1 Druckergrundlagen Vielen Dank, dass Sie sich für einen HP LaserJet 2400 Serie-Drucker entschieden haben. Falls noch nicht geschehen, führen Sie die Anweisungen zum Einrichten im Leitfaden zur Inbetriebnahme (Inbetriebnahme) aus, der im Lieferumfang des Druckers enthalten ist. Nachdem der Drucker eingerichtet wurde und betriebsbereit ist, nehmen Sie sich einige Augenblicke Zeit, um sich mit den Funktionen des Druckers vertraut zu machen.
Schneller Zugriff auf Druckerinformationen In diesem Abschnitt wird eine Übersicht über die verfügbaren Ressourcen gegeben, in denen Sie weitere Informationen zu Einrichtung und Verwendung des Druckers erhalten. Verknüpfungen mit dem Benutzerhandbuch ● Teilenummern ● Bedienfeldanordnung ● Ablaufdiagramm zur Fehlerbehebung Hier finden Sie weitere Informationen Zum Arbeiten mit diesem Drucker stehen Ihnen verschiedene Referenzen zur Verfügung. Informationen hierzu finden Sie unter www.hp.
Druckerkonfigurationen Der Drucker HP LaserJet 2400 Serie ist in unterschiedlichen Konfigurationen erhältlich. Die Buchstaben, die auf den Druckernamen folgen, weisen auf die Unterschiede in den einzelnen Konfigurationen hin. Jeder Buchstabe verweist auf ein bestimmtes Merkmal. Anhand der Informationen in diesem Abschnitt können Sie herausfinden, welche Merkmale Ihr Modell aufweist. Hinweis Es sind nicht alle Modelle in allen Konfigurationen erhältlich.
Druckermerkmale In den folgenden Tabellen werden die Merkmale der HP LaserJet 2400 Serie Drucker beschrieben. Geschwindigkeit HP LaserJet 2410 Drucker Drucker der HP LaserJet 2420 Serie Drucker der HP LaserJet 2430 Serie Druckt 25 Seiten pro Minute (ppm) bei Papier im LetterFormat. Druckt 30 Seiten/Min. bei Papier im Letter-Format. Druckt 35 Seiten/Min. bei Papier im Letter-Format. Druckt 28 Seiten/Min. bei Papier im A4-Format. Druckt 33 Seiten/Min. bei Papier im A4-Format.
Speicher und Prozessor HP LaserJet 2410-Drucker Drucker der HP LaserJet 2420 Serie Drucker der HP LaserJet 2430 Serie 32 MB Arbeitsspeicher (RAM). Der Drucker HP LaserJet 2420 enthält 32 MB Arbeitsspeicher (RAM), erweiterbar auf bis zu 288 MB. Der Drucker HP LaserJet 2430t enthält 48 MB Arbeitsspeicher (RAM), erweiterbar auf bis zu 304 MB. Der Drucker HP LaserJet 2420d enthält 48 MB RAM, erweiterbar auf bis zu 304 MB.
Druckersprache und Schriftarten HP LaserJet 2410-Drucker Drucker der HP LaserJet 2420 Serie Drucker der HP LaserJet 2430 Serie HP PCL6, PCL 5e und HP PostScript® (PS-)3Emulation HP PCL6, PCL 5e und HP PostScript® (PS-)3Emulation. HP PCL6, PCL 5e und HP PostScript® (PS-)3Emulation. 80 Schriftarten für Microsoft® Windows®. 80 Schriftarten für Microsoft® Windows®. 80 Schriftarten für Microsoft® Windows®.
Sparsames Drucken HP LaserJet 2410-Drucker Drucker der HP LaserJet 2420 Serie Drucker der HP LaserJet 2430 Serie Durch den n-Seiten-Druck Durch den n-Seiten-Druck Durch den n-Seiten-Druck (mehrere Seiten auf einem (mehrere Seiten auf einem (mehrere Seiten auf einem Blatt) können Sie Papier sparen. Blatt) können Sie Papier sparen. Blatt) können Sie Papier sparen. Durch den Duplexdruck (bei Modellen, die über ein Duplexdruckzubehör verfügen) können Sie Papier sparen.
Druckerkomponenten Vor dem Verwenden des Druckers sollten Sie sich mit den einzelnen Komponenten vertraut machen.
Schnittstellenanschlüsse Der Drucker verfügt über vier Schnittstellenanschlüsse: einen EIO-Steckplatz und drei Anschlüsse für die Verbindung mit einem Computer oder einem Netzwerk. 1 EIO 2 3 4 1 2 3 4 DEWW EIO-Steckplatz Integrierter HP Jetdirect-Druckserver (nur Modelle HP LaserJet 2420n, 2420dn, 2430tn und 2430dtn) USB 2.
Bedienfeld Dieser Abschnitt enthält Informationen über das Bedienfeld und seine Funktionen: ● Bedienfeldanordnung ● Bedienfeldtasten ● Bedienfeld-LEDs ● Drucken von Bedienfeldmenüs ● Ändern von Konfigurationseinstellungen des Druckerbedienfelds ● Verwenden der Hilfe des Druckers Das Bedienfeld befindet sich auf der Oberseite des Druckers.
Bedienfeldtasten Taste Funktion (HILFE) ● Bietet Informationen über Meldungen, die an der Grafikanzeige eingeblendet werden. (ZURÜCK) ● Eine Ebene in der Menühierarchie oder einen numerischen Eintrag zurück. ● Beendet das Menü, wenn sie länger als eine Sekunde gedrückt wird. ● Öffnet und beendet die Menüs. (NACH OBEN) ● Navigiert zum vorherigen Element in der Liste oder erhöht den Wert numerischer Elemente. (AUSWÄHLEN) ● Löscht Fehlerbedingungen, sofern sie entfernt werden können.
LED Zustand Anzeige Daten Leuchtet Der Drucker hat Daten, die gedruckt werden sollen, wartet jedoch ab, bis alle Daten eingetroffen sind. Leuchtet nicht Der Drucker hat keine Daten, die gedruckt werden sollen. Blinkt Der aktuelle Druckjob wird verarbeitet oder gedruckt. Leuchtet Ein Druckerproblem ist aufgetreten. Notieren Sie die am Bedienfeld angezeigte Meldung, und schalten Sie den Drucker aus und wieder ein.
Drücken Sie zum Beenden der Hilfe erneut auf (Taste HILFE). Ändern von Konfigurationseinstellungen des Druckerbedienfelds Über das Druckerbedienfeld können Sie Änderungen an den allgemeinen Standardeinstellungen der Druckerkonfiguration vornehmen, wie z.B. Papierformat und -typ für ein Fach, Bereitschaftseinstellung, Druckersprache (Personality) und Papierstaubehebung.
So zeigen Sie die IP-Adresse an 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2. Drücken Sie (Taste NACH UNTEN), um GERÄT KONFIGURIEREN zu markieren. 3. Drücken Sie (Taste AUSWÄHLEN), um GERÄT KONFIGURIEREN auszuwählen. 4. Drücken Sie (Taste NACH UNTEN), um SYSTEM-SETUP zu markieren. 5. Drücken Sie (Taste AUSWÄHLEN), um SYSTEM-SETUP auszuwählen. 6. Drücken Sie (Taste NACH UNTEN), um ADRESSE ANZEIGEN zu markieren. 7. Drücken Sie (Taste AUSWÄHLEN), um ADRESSE ANZEIGEN auszuwählen. 8.
So legen Sie "Angefordertes Fach verwenden" fest 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2. Drücken Sie (Taste NACH UNTEN), um GERÄT KONFIGURIEREN zu markieren. 3. Drücken Sie (Taste AUSWÄHLEN), um GERÄT KONFIGURIEREN auszuwählen. 4. Drücken Sie (Taste NACH UNTEN), um SYSTEM-SETUP zu markieren. 5. Drücken Sie (Taste AUSWÄHLEN), um SYSTEM-SETUP auszuwählen. 6. Drücken Sie (Taste NACH UNTEN), um FACH- EIGENSCHAFTEN zu markieren. 7.
So legen Sie den Druckerstandard für PS-Verzögerung von Druckmedien fest 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2. Drücken Sie (Taste NACH UNTEN), um GERÄT KONFIGURIEREN zu markieren. 3. Drücken Sie (Taste AUSWÄHLEN), um GERÄT KONFIGURIEREN auszuwählen. 4. Drücken Sie (Taste NACH UNTEN), um SYSTEM-SETUP zu markieren. 5. Drücken Sie (Taste AUSWÄHLEN), um SYSTEM-SETUP auszuwählen. 6. Drücken Sie (Taste NACH UNTEN), um FACH- EIGENSCHAFTEN zu markieren. 7.
So legen Sie die Bereitschaftseinstellung fest 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2. Drücken Sie (Taste NACH UNTEN), um GERÄT KONFIGURIEREN zu markieren. 3. Drücken Sie (Taste AUSWÄHLEN), um GERÄT KONFIGURIEREN auszuwählen. 4. Drücken Sie (Taste NACH UNTEN), um SYSTEM-SETUP zu markieren. 5. Drücken Sie (Taste AUSWÄHLEN), um SYSTEM-SETUP auszuwählen. 6. Drücken Sie (Taste NACH UNTEN), um BEREITSCHAFTSEINSTELLUNG zu markieren. 7.
So stellen Sie die Druckersprache ein 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2. Drücken Sie (Taste NACH UNTEN), um GERÄT KONFIGURIEREN zu markieren. 3. Drücken Sie (Taste AUSWÄHLEN), um GERÄT KONFIGURIEREN auszuwählen. 4. Drücken Sie (Taste NACH UNTEN), um SYSTEM-SETUP zu markieren. 5. Drücken Sie (Taste AUSWÄHLEN), um SYSTEM-SETUP auszuwählen. 6. Drücken Sie (Taste NACH UNTEN), um DRUCKERSPRACHE zu markieren. 7. Drücken Sie (Taste AUSWÄHLEN), um DRUCKERSPRACHE auszuwählen. 8.
Automatische Fortsetzung Sie können festlegen, wie der Drucker reagieren soll, wenn im System ein Fehler auftritt, bei dem die automatische Fortsetzung möglich ist. EIN ist die Standardeinstellung. ● Wählen Sie EIN, wenn zehn Sekunden lang eine Fehlermeldung angezeigt werden soll, bevor das Drucken automatisch fortgesetzt wird. ● Wählen Sie AUS, damit das Drucken bei jeder angezeigten Fehlermeldung angehalten wird, bis Sie (Taste AUSWÄHLEN) drücken. So stellen Sie die automatische Fortsetzung ein 1.
So stellen Sie Mitteilungen zu fast leeren Verbrauchsmaterialien ein 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2. Drücken Sie (Taste NACH UNTEN), um GERÄT KONFIGURIEREN zu markieren. 3. Drücken Sie (Taste AUSWÄHLEN), um GERÄT KONFIGURIEREN auszuwählen. 4. Drücken Sie (Taste NACH UNTEN), um SYSTEM-SETUP zu markieren. 5. Drücken Sie (Taste AUSWÄHLEN), um SYSTEM-SETUP auszuwählen. 6. Drücken Sie (Taste NACH UNTEN), um PATRONE FAST LEER zu markieren. 7.
Papierstaubehebung Mit dieser Option können Sie konfigurieren, wie der Drucker auf Papierstaus reagieren soll, z.B. wie der Drucker mit den betroffenen Seiten umgeht. AUTOM. ist der Standardwert. ● AUTOM.. Der Drucker aktiviert die Papierstaubehebung automatisch, wenn genügend Speicher vorhanden ist. ● EIN. Der Drucker druckt jede Seite, die an einem Papierstau beteiligt ist, neu.
So legen Sie die RAM-Disk fest 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2. Drücken Sie (Taste NACH UNTEN), um GERÄT KONFIGURIEREN zu markieren. 3. Drücken Sie (Taste AUSWÄHLEN), um GERÄT KONFIGURIEREN auszuwählen. 4. Drücken Sie (Taste NACH UNTEN), um SYSTEM-SETUP zu markieren. 5. Drücken Sie (Taste AUSWÄHLEN), um SYSTEM-SETUP auszuwählen. 6. Drücken Sie (Taste NACH UNTEN), um RAM-DISK zu markieren. 7. Drücken Sie (Taste AUSWÄHLEN), um RAM-DISK auszuwählen. 8.
Software Im Lieferumfang des Druckers ist nützliche Software enthalten, einschließlich Druckertreiber und optionaler Software. HP empfiehlt zur einfachen Einrichtung des Druckers und für den Zugriff auf den gesamten Funktionsumfang dringend die Installation der mitgelieferten Software. Zusätzliche Software und Sprachen entnehmen Sie den Installationshinweisen und ReadmeDateien auf der Drucker-CD-ROM. HP Software ist nicht in allen Sprachen verfügbar.
*Nur über das World Wide Web verfügbar. Druckertreiber Druckertreiber ermöglichen den Zugriff auf die Druckerfunktionen und sorgen dafür, dass über eine Druckersprache eine Verbindung zwischen Computer und Drucker hergestellt werden kann. Informationen zu weiteren Anwendungen und Sprachen finden Sie in den Installationshinweisen, der Readme- und aktuellen Readme-Datei auf der Drucker-CD-ROM. Folgende Druckertreiber sind im Lieferumfang des Druckers enthalten.
Hinweis ● Model Scripts für UNIX. ● Linux-Treiber. ● HP OpenVMS-Treiber. Die OS/2-Treiber erhalten Sie bei IBM. Sie gehören zum Lieferumfang von OS/2. Die Treiber stehen für folgende Sprachen nicht zur Verfügung: Vereinfachtes Chinesisch, Koreanisch, Japanisch und Traditionelles Chinesisch. Auswahl des Ihren Anforderungen entsprechenden Druckertreibers Wählen Sie je nach Verwendung des Druckers den geeigneten Druckertreiber aus.
Betriebssystem Zum Ändern der Einstellungen für alle Druckaufträge, bis das Softwareprogramm geschlossen wird Zum Ändern der Standardeinstellungen für Druckaufträge (zum Beispiel standardmäßiges Aktivieren von Beidseitiger Druck) Zum Ändern der Konfigurationseinstellungen (zum Beispiel Hinzufügen eines optionalen Fachs oder Aktivieren/Deaktivieren einer Treiberfunktion wie etwa Manuellen Duplexdruck zulassen) Windows 98, NT 4.
Betriebssystem Zum Ändern der Einstellungen für alle Druckaufträge, bis das Softwareprogramm geschlossen wird Zum Ändern der Standardeinstellungen für Druckaufträge (zum Beispiel standardmäßiges Aktivieren von Beidseitiger Druck) Zum Ändern der Konfigurationseinstellungen (zum Beispiel Hinzufügen eines optionalen Fachs oder Aktivieren/Deaktivieren einer Treiberfunktion wie etwa Manuellen Duplexdruck zulassen) Macintosh OS X V10.2 Klicken Sie im Menü Ablage auf die Option Drucken.
PPDs Die Verwendung der PPDs in Verbindung mit den Apple PostScript-Treibern ermöglicht den Zugriff auf die Funktionen des Druckers und die Kommunikation des Computers mit dem Drucker. Ein Installationsprogramm für die PPDs, PDEs und andere Anwendungen finden Sie auf der CD-ROM. Verwenden Sie den geeigneten PS-Treiber des Betriebssystems. HP LaserJet-Dienstprogramm Mit Hilfe des HP LaserJet-Dienstprogramms können Sie Druckfunktionen steuern, die im Druckertreiber nicht verfügbar sind.
Installieren von Windows-Drucksystemsoftware für Direktverbindungen In diesem Abschnitt wird erläutert, wie Sie die Drucksystemsoftware für Microsoft Windows 98, Windows Me, Windows NT 4.0, Windows 2000, Windows XP und Windows Server 2003 installieren. Installieren Sie die Drucksoftware bei einer Umgebung mit Direktverbindung stets, bevor Sie das Parallel- oder USB-Kabel anschließen.
Der HP Jetdirect-Druckserver, der zum Lieferumfang von Druckermodellen gehört, die den Buchstaben "n" im Modellnamen tragen, verfügt über einen 10/100Base-TXNetzwerkanschluss. Weitere Optionen finden Sie unter Bestellen von Druckerteilen, Zubehör und Verbrauchsmaterialien, oder wenden Sie sich an Ihren HP Partner. Informationen dazu finden Sie unter HP Kundendienst. Das Installationsprogramm unterstützt jedoch nicht die Druckerinstallation oder Druckerobjekterstellung auf Novell-Servern.
Installieren von Macintosh-Drucksystemsoftware für Netzwerke Dieser Abschnitt beschreibt die Installation der Macintosh-Drucksystemsoftware. Die Drucksystemsoftware unterstützt Apple Mac OS 9.x und höher sowie OS X V10.1 und höher. Zur Drucksystemsoftware gehören die folgenden Komponenten: ● PostScript Printer Description-Dateien.
2. Legen Sie die CD-ROM in das CD-ROM-Laufwerk ein. Das CD-ROM-Menü wird automatisch aufgerufen. Wird das CD-ROM-Menü nicht automatisch aufgerufen, doppelklicken Sie auf das CD-ROM-Symbol auf dem Desktop und anschließend auf das Symbol Installer. Das Symbol befindet sich im Ordner Installer/ der Starter CD-ROM (wobei für die von Ihnen bevorzugte Sprache steht). Beispiel: Der Ordner Installer/English enthält das Installer-Symbol für die englische Druckersoftware. 3.
4. Folgen Sie den Anleitungen auf dem Bildschirm. 5. Starten Sie den Computer neu. 6. Für Mac OS 9.x: 1. Klicken Sie unter Festplattenlaufwerk auf Applications, Dienstprogramme, und öffnen Sie das Druckersymbole-Dienstprogramm von Apple. 2. Doppelklicken Sie auf USB-Drucker, und klicken Sie auf OK. 3. Klicken Sie neben Ausgewählter USB-Drucker auf Ändern. 4. Wählen Sie den Drucker aus, und klicken Sie dann auf OK. 5.
Wenn die Installation fehlgeschlagen ist, installieren Sie die Software neu. Wenn die Software nicht erneut installiert werden kann, lesen Sie die Installationshinweise und Readme-Dateien auf der Drucker-CD-ROM oder das mit dem Drucker gelieferte Infoblatt, oder informieren Sie sich unter http://www.hp.com/go/lj2410_software, http://www.hp.com/go/ lj2420_software, oder http://www.hp.com/go/lj2430_software. So installieren Sie die Software für Windows 2000, Windows XP oder Windows Server 2003 1.
So entfernen Sie Software in Macintosh-Betriebssystemen Ziehen Sie den Ordner HP LaserJet und die PPDs in den Papierkorb: DEWW ● Unter Mac OS 9 befinden sich die Ordner auf Festplattenlaufwerk/HP LaserJet sowie in Festplattenlaufwerk/Systemordner/Systemerweiterungen/Druckerbeschreibungen. ● Unter Mac OS X befinden sich die Ordner auf Festplattenlaufwerk/Library/Printers/PPDs/ Contents/Resources/EN.lproj.
Auswählen von Druckmedien Dieser Drucker unterstützt eine Vielzahl von Druckmedien, wie z.B. Einzelblattpapier (einschließlich 100-%-Recyclingpapier), Umschläge, Etiketten, Transparentfolien und Papier in Sonderformaten. Eigenschaften wie Gewicht, Zusammensetzung, Maserung und Feuchtigkeitsgehalt sind wichtige Faktoren für die Leistung des Druckers und die Ausgabequalität.
benutzerdefinierte Papierformate finden Sie unter Drucken auf Spezialmedien mit benutzerdefiniertem Format oder Karton. 2 Das Fassungsvermögen des Fachs hängt vom Gewicht und der Stärke des Druckmediums sowie von den Umgebungsbedingungen ab. 3 Glätte: 100 bis 250 Sheffield. Hinweis Wenn Sie Druckmedien verwenden, die kürzer als 178 mm (7 Zoll) sind, kann es leicht zu Staus kommen. Diese Staus können auch durch Papier verursacht werden, das durch Umwelteinflüsse verändert wurde.
Letter 216 x 279 mm (8,5 x 11 Zoll) A4 60 bis 105 g/m2 (16 bis 28 lb Schreibmaschinen papier) 210 x 297 mm (8,3 x 11,7 Zoll) Legal 216 x 356 mm (8,5 x 14 Zoll) 8,5 x 13 Zoll 216 x 330 mm (8,5 x 13 Zoll) 1 Der integrierte Duplexer ist nur im Lieferumfang der Drucker HP LaserJet 2420d, 2420dn und 2430dtn enthalten. 2 Der Drucker unterstützt eine Vielzahl unterschiedlicher Formate. Die unterstützten Formate können Sie der Druckersoftware entnehmen.
2 Druckaufgaben In diesem Abschnitt finden Sie Informationen zu häufigen Druckaufgaben.
Auswählen des zu verwendenden Fachs Sie können die Reihenfolge der Fächer für die Medienzufuhr auswählen. Die folgenden Abschnitte enthalten Informationen zur Konfiguration des Druckers für die Nutzung bestimmter Fächer bei der Medienzufuhr.
Einstellung Erläuterung FACH 1 TYP=BELIEBIG In der Regel verwendet der Drucker Medien aus Fach 1, es sei denn, es ist leer oder geschlossen. Wenn in Fach 1 nicht ständig Medien eingelegt sind oder Sie Fach 1 nur für die manuelle Medienzufuhr verwenden, sollten Sie dennoch im Papierzufuhrmenü die Standardeinstellungen FACH 1 TYP=BELIEBIG und FACH 1 GRÖSSE=BELIEBIG beibehalten. FACH 1 GRÖSSE=BELIEBIG FACH 1 TYP= bzw.
So drucken Sie nach Papiertyp und -format 1. Achten Sie darauf, in die Fächer stets das entsprechende Papier einzulegen. (Weitere Informationen finden Sie unter Einlegen von Druckmedien in die Fächer.) 2. Öffnen Sie über das Druckerbedienfeld das Menü PAPIERZUFUHR. Wählen Sie für jedes Fach den Papiertyp aus. Wenn Sie nicht sicher sind, welchen Papiertyp Sie gerade einlegen, z.B. Schreibmaschinen- oder Recyclingpapier, sehen Sie auf dem Etikett der Medienverpackung nach. 3.
Auswählen des richtigen Fixierermodus Der Fixierermodus wird automatisch je nach dem für das Fach eingestellten Medientyp angepasst. Beispielsweise ist für schweres Papier, z.B. Karton, möglicherweise ein höherer Fixierermodus erforderlich, damit der Toner besser an der Seite haftet. Für Transparentfolien ist hingegen der Fixierermodus NIEDRIG erforderlich, um Schäden am Drucker zu vermeiden. In der Standardeinstellung liegen für die meisten Druckmedientypen in der Regel optimale Bedingungen vor.
Einlegen von Druckmedien in die Fächer Legen Sie Spezialdruckmedien wie Briefumschläge, Etiketten und Transparentfolien nur in Fach 1 ein. Legen Sie in Fach 2 oder das optionale Fach 3 nur Papier ein. Einlegen von Druckmedien in Fach 1 (Mehrzweckfach) In Fach 1 können bis zu 100 Blatt Papier, bis zu 75 Transparentfolien, bis zu 50 Etikettenbögen oder bis zu 10 Umschläge eingelegt werden.
4. Legen Sie das Druckmedium in das Fach ein (kurze Seite nach innen, zu bedruckende Seite nach oben). Die Druckmedien sollten zwischen den Druckmedien-Querführungen mittig ausgerichtet sein und unter den Zungen der Führungen liegen. 5. Schieben Sie die Medienbreitenführungen so weit nach innen, bis diese den Druckmedienstapel auf beiden Seiten leicht berühren, ohne ihn zu biegen. Stellen Sie sicher, dass sich die Druckmedien unterhalb der Höhenbegrenzungen an den Medienbreitenführungen befinden.
2. Schieben Sie die Medienbreitenführungen nach außen, so dass der Zeiger auf das von Ihnen eingelegte Papierformat eingestellt ist. 3. Drücken Sie an der hinteren Längsführung auf die blaue Halterung, und richten Sie sie so aus, dass der Zeiger auf das Papierformat zeigt, das Sie einlegen. B5 JIS LEGAL 8.5" X13" A4 LETTER B5 ISO EXECUTIVE 4. Legen Sie das Papier in das Fach ein, und stellen Sie sicher, dass es an allen vier Ecken eben im Fach liegt.
6. Schieben Sie das Fach in den Drucker. Hinweis Wenn Sie Fach 2 aus dem Drucker herausnehmen, drücken Sie das Papier immer nach unten, um die metallene Papierhebeplatte einrasten zu lassen, und setzen Sie das Fach wieder ein. Die metallene Papierhebeplatte sorgt dafür, dass das Papier beim Einschieben des Fachs freigegeben und angehoben wird. Einlegen von Druckmedien in das optionale Fach 3 (500-BlattFach) Fach 3 unterstützt nur Papier (A4, A5, B5 JIS, Letter, Legal, Executive und 216 x 330 mm).
3. Stellen Sie die Querführung auf das richtige Papierformat ein. 4. Legen Sie das Papier in das Fach ein, und stellen Sie sicher, dass es an allen vier Ecken eben im Fach liegt. Vergewissern Sie sich, dass sich das Papier unterhalb der Haken an den Seiten und am hinteren Ende des Fachs befindet. 5. Schieben Sie das Fach in den Drucker.
Ausgabeoptionen für Medien Der Drucker wird mit zwei Ausgabefächern geliefert. Das obere Ausgabefach wird verwendet, wenn das hintere Ausgabefach geschlossen ist. Das hintere Ausgabefach wird verwendet, wenn dieses geöffnet ist. 1 2 1 2 Hinweis DEWW Oberes Ausgabefach (Druckseite unten) Hinteres Ausgabefach (Druckseite oben) Ein gerader Papierpfad führt von Fach 1 zum hinteren Ausgabefach, wenn diese beiden Fächer für einen Druckauftrag verwendet werden.
Drucken von Briefumschlägen Sie können Umschläge von Fach 1 aus bedrucken. In Fach 1 können bis zu zehn Umschläge in Standard- oder benutzerdefinierten Formaten eingelegt werden. Stellen Sie beim Drucken von Umschlägen in beliebigen Formaten sicher, dass der Abstand für die Ränder in der Softwareanwendung auf einen Wert von mindestens 15,0 mm vom Umschlagrand eingestellt wurde. Die Druckgeschwindigkeit ist beim Drucken von Umschlägen möglicherweise geringer.
3. Stellen Sie die Querführungen von Fach 1 etwas breiter als die Umschläge ein. 4. Legen Sie die Umschläge mit der kurzen Seite nach innen und der zu bedruckenden Seite nach oben in das Fach ein. Die Frankierseite muss zuerst in den Drucker eingezogen werden. 5. Schieben Sie die Querführungen nach innen, bis sie den Stapel mit den Umschlägen leicht berühren, ohne ihn zu krümmen. Die Umschläge sollten zwischen den Papierführungen mittig ausgerichtet sein und unter den Zungen der Führungen liegen.
Drucken auf Spezialmedien In diesem Abschnitt wird das Drucken auf Medientypen beschrieben, für die eine besondere Vorgehensweise erforderlich ist: ● Drucken von Etiketten ● Drucken von Transparentfolien ● Drucken auf Spezialmedien mit benutzerdefiniertem Format oder Karton ● Bedrucken von Briefkopfpapier, gelochtem oder vorgedrucktem Papier (einseitig) Drucken von Etiketten Verwenden Sie nur Etiketten, die für den Gebrauch mit Laserdruckern geeignet sind.
Drucken von Transparentfolien Verwenden Sie nur Transparentfolien, die für Laserdrucker empfohlen werden. Spezifikationen für Transparentfolien sind im Abschnitt Transparentfolien aufgeführt. Richtlinien für das Bedrucken von Transparentfolien ● Drucken Sie Transparentfolien von Fach 1 aus. ● Verwenden Sie das obere Ausgabefach, um ein Verbiegen der Folien zu vermeiden (dies gilt nur für Folien; bei allen anderen Medien sollte das hintere Ausgabefach verwendet werden, um ein Verbiegen zu verhindern).
Richtlinien für das Bedrucken von Medien mit Sonderformat und Karton ● Führen Sie die kurze Seite immer zuerst in Fach 1 ein. Wenn Sie im Querformat drucken möchten, legen Sie diese Einstellung in der Software fest. Wenn Sie das Papier mit der langen Kante zuerst einführen, kann es sich stauen. ● Verwenden Sie das hintere Ausgabefach, um ein Verbiegen möglichst zu vermeiden. ● Drucken Sie nicht auf Medien, deren Breite unter 76 mm (3 Zoll) und deren Länge unter 127 mm (5 Zoll) liegt.
Ausrichtung von Fach 2 oder Fach 3: bedruckte Seite zeigt nach unten, obere Kante zeigt zu Ihnen. Hinweis Wenn der Modus Alternatives Briefkopfpapier im Druckertreiber aktiviert und Briefkopfpapier oder Vorgedruckt als Medientyp ausgewählt ist, müssen Sie das Medium für den beidseitigen (Duplex-)Druck ausrichten.
Beidseitiger Druck (Duplexdruck) Sie können beim so genannten Duplexdruck oder beidseitigem Drucken beide Seiten eines Papierbogens auf zwei Arten bedrucken: automatisch und manuell. Für automatischen Duplexdruck werden folgende Papierformate unterstützt: Letter, A4, Legal und 216 x 330 mm. Manueller Duplexdruck ist für alle Papierformate möglich. ● Automatischer Duplexdruck: Der integrierte automatische Duplexer ist nur im Lieferumfang der Drucker HP LaserJet 2420d, 2420dn und 2430dtn enthalten.
Layoutoptionen für den beidseitigen Druck Auf der folgenden Abbildung sehen Sie die vier Optionen der Druckausrichtung. Diese Optionen stehen zur Verfügung, wenn im Druckertreiber auf der Registerkarte Fertigstellung der Eintrag Beidseitiger Druck aktiviert ist. 1 4 3 2 2 2 3 2 5 3 2 5 3 5 3 5 1. lange Seite in Querformat* Dieses Layout wird häufig bei Buchhaltungs-, Datenverarbeitungs- und Tabellenkalkulationsprogrammen verwendet. Jedes zweite Druckbild ist verkehrt herum ausgerichtet.
1. Legen Sie genügend Papier in das Fach ein, über das der Druckauftrag ausgeführt werden soll. Spezialpapier, z.B. Briefkopfpapier, ist wie folgt einzulegen: VORSICHT ● Bei Fach 1 legen Sie das Briefkopfpapier mit der Vorderseite nach unten und der unteren Kante zuerst ein. ● Bei allen anderen Fächern legen Sie Briefkopfpapier mit der Vorderseite nach oben und der oberen Kante in Richtung Fachrückseite ein. Legen Sie kein Papier ein, das schwerer als 105 g/m2 (28 lb Briefpapier) ist.
Abbrechen eines Druckauftrags Sie können einen Druckauftrag aus einem Softwareprogramm oder einer Druckwarteschlange heraus oder durch Drücken der Taste STOPP am Druckerbedienfeld abbrechen. ● Wenn der Drucker den Druckvorgang noch nicht begonnen hat, sollten Sie zuerst versuchen, den Druckjob aus dem Softwareprogramm heraus abzubrechen, mit dem der Job gesendet wurde. ● Befindet sich der Druckjob in einer Druckwarteschlange oder einem Druckspooler (wie z.B.
Verwenden des Druckertreibers Der Druckertreiber ermöglicht den Zugriff auf Druckerfunktionen und erlaubt die Kommunikation zwischen Computer und Drucker. Dieser Abschnitt enthält Anleitungen zum Drucken, wenn die Optionen vom Druckertreiber eingestellt werden. Versuchen Sie, nach Möglichkeit die Druckfunktionen im Dialogfeld "Drucken" oder in dem Softwareprogramm einzustellen, mit dem Sie arbeiten.
Ändern der Standardeinstellungen Wenn die Druckereinstellungen nicht in allen Softwareprogrammen verwendet werden, die Sie auf Ihrem Computer einsetzen, ändern Sie die Standardeinstellungen im Druckertreiber. Wählen Sie das Verfahren für Ihr Betriebssystem aus: ● So ändern Sie die Standardeinstellungen in Windows 98 und Windows Me ● So ändern Sie die Standardeinstellungen in Windows NT 4.
4. Klicken Sie mit der rechten Maustaste auf das Symbol für den HP LaserJet 2400 Serie Drucker. 5. Klicken Sie auf Eigenschaften. 6. Klicken Sie auf der Registerkarte Erweitert auf Druckstandardwerte. 7. Ändern Sie die Einstellungen auf den Registerkarten. Diese Einstellungen sind nun die Standardeinstellungen für den Drucker. 8. Klicken Sie auf OK, um zur Registerkarte Erweitert zurückzukehren. 9. Klicken Sie auf OK, um Ihre Einstellungen zu speichern und den Druckertreiber zu schließen.
Funktionen des Druckertreibers In diesem Abschnitt werden allgemeine Druckfunktionen beschrieben, die vom Druckertreiber gesteuert werden.
Drucken mehrerer Seiten auf einem Blatt Papier Sie können mehrere Dokumentseiten auf einem Blatt Papier drucken (wird manchmal auch 2-up-, 4-up- oder N-up-Druck genannt). Die Seiten werden verkleinert auf dem Blatt angeordnet. Sie können angeben, dass maximal 16 Seiten auf einem Blatt gedruckt werden. Diese Funktion bietet, insbesondere in Kombination mit dem Duplexdruck, einen kosteneffektiven und umweltverträglichen Weg, um Entwurfsseiten zu drucken (siehe Beidseitiger Druck (Duplexdruck)).
So stellen Sie ein benutzerdefiniertes Papierformat auf MacintoshComputern ein Für Mac OS 9 1. Wählen Sie im Menü Ablage die Option Papierformat. 2. Wählen Sie im Dropdown-Menü Seiteneinstellungen die Option Benutzerdefiniertes Format aus. 3. Klicken Sie auf Neu, um ein neues benutzerdefiniertes Format zu erstellen. Die neue benutzerdefinierte Seite wird automatisch zum Menü Papiergröße unter Papierformat hinzugefügt. Für Mac OS X 1. Wählen Sie im Menü Ablage die Option Papierformat. 2.
Auswahl der Einstellungen für die Druckqualität Wenn Sie eine hohe Druckqualität benötigen, wählen Sie eine benutzerdefinierte Einstellung. Optionen für die Druckauflösung Hinweis ● Beste Qualität – ProRes 1200 dpi für beste Druckqualität. ● Schnelldruck – FastRes 1200 dpi, alternative Auflösung für komplexe Grafiken oder eine schnellere Druckausgabe. ● Benutzerdefiniert – Gibt Ihnen die Möglichkeit, die Einstellungen für die Druckqualität selbst festzulegen.
2. Wählen Sie auf der Registerkarte Papier/Qualität die Quelle in der Dropdown-Liste Papierquelle aus. 3. Klicken Sie auf OK. So wählen Sie die Papierzufuhr auf Macintosh-Computern aus Für Mac OS 9: Wählen Sie eine Papierzufuhr aus den Optionen unter Allgemein im Druckertreiber aus. Für Mac OS X: Klicken Sie auf Ablage, Drucken und Papiereinzug.
Verwenden der Jobspeicherungsfunktionen Der Drucker unterstützt zwei unterschiedliche Jobspeicherungsfunktionen, mit denen Sie den Druckvorgang über das Druckerbedienfeld starten können, nachdem ein Druckjob vom Computer gesendet wurde: ● Prüf- und Aufbewahrungsjobs ● Private Jobs Sie müssen vor dem Drucken Ihre Jobs im Druckertreiber eindeutig kennzeichnen. Wenn Sie Standardnamen verwenden, können frühere Jobs mit demselben Standardnamen überschrieben werden, oder der Job könnte gelöscht werden.
Hinweis Beim Ausschalten des Druckers werden alle Schnellkopiejobs, Prüf- und Aufbewahrungsjobs sowie privaten Druckjobs gelöscht. Aufbewahrte Jobs können auch über das Druckerbedienfeld gelöscht werden. So löschen Sie einen aufbewahrten Job 1. Drücken Sie (Taste AUSWÄHLEN), um die Menüs zu öffnen. 2. Blättern Sie mit (Taste NACH OBEN) oder (Taste NACH UNTEN) zu JOB WIEDERAUFNEHMEN, und drücken Sie dann auf (Taste AUSWÄHLEN). 3.
Löschen von privaten Jobs Private Jobs werden nach der Druckfreigabe automatisch von der Festplatte des Druckers gelöscht. Dies kann verhindert werden, indem im Treiber die Option Gespeicherter Job ausgewählt wird. Hinweis Beim Ausschalten des Druckers werden alle Schnellkopiejobs, Prüf- und Aufbewahrungsjobs sowie privaten Druckjobs gelöscht. Private Jobs können auch über das Bedienfeld des Druckers gelöscht werden, bevor sie gedruckt werden. So löschen Sie private Jobs 1.
3 Verwalten und Warten des Druckers In diesem Kapitel geht es um folgende Themen: DEWW ● Verwenden des integrierten Webservers ● Verwenden der HP WebJet Admin-Software ● Verwenden von HP Toolbox ● Deinstallieren von HP Toolbox ● Verwalten und Konfigurieren von Druckertreibern ● Konfigurieren von E-Mail-Warnmeldungen ● Einstellen der Echtzeituhr ● Überprüfen der Druckerkonfiguration ● Verwalten der Druckpatrone ● Reinigen des Druckers 71
Verwenden des integrierten Webservers Mit dem integrierten Webserver können Sie von Ihrem Computer anstelle vom Druckerbedienfeld aus den Drucker- und den Netzwerkstatus anzeigen und Druckfunktionen verwalten. Folgende Beispiele zeigen, welche Aufgaben mit dem integrierten Webserver ausgeführt werden können: ● Druckerkontrollstatusinformationen anzeigen ● In die einzelnen Fächer eingelegte Medientypen einstellen ● Die verbleibende Lebensdauer aller Verbrauchsmaterialien feststellen und ggf.
2. Der integrierte Webserver bietet drei Registerkarten mit Einstellungen und Informationen über den Drucker: Informationen, Einstellungen und Netzwerk. Klicken Sie auf die Registerkarte, die Sie anzeigen möchten. 3. Die folgenden Abschnitte enthalten weitere Informationen über die einzelnen Registerkarten. Registerkarte "Informationen" Die Seitengruppe "Informationen" besteht aus den folgenden Seiten. ● Gerätestatus.
● Andere Verknüpfungen. Fügen Sie eine Verknüpfung zu einer anderen Website hinzu, oder bearbeiten Sie sie. Die Verknüpfung wird im Bereich Andere Verknüpfungen aller Seiten des integrierten Webservers angezeigt. Diese permanenten Verknüpfungen werden ständig im Bereich Andere Verknüpfungen angezeigt: HP Instant Support, Verbrauchsmaterial bestellen und Produktunterstützung. ● Geräteinformationen. Benennen Sie den Drucker, und weisen Sie ihm eine Gerätenummer zu.
Verwenden der HP WebJet Admin-Software Bei HP Web JetAdmin handelt es sich um eine webbasierte Softwarelösung für die Remoteinstallation, -überwachung und -fehlerbehebung von Peripheriegeräten, die mit einem Netzwerk verbunden sind. Über die benutzerfreundliche Browseroberfläche wird die Plattform übergreifende Verwaltung einer Vielzahl von Geräten, einschließlich HP Drucker und Drucker anderer Hersteller, vereinfacht.
Verwenden von HP Toolbox HP Toolbox ist eine Webanwendung, die Sie für folgende Aufgaben nutzen können: ● Überprüfen des Druckerstatus ● Konfigurieren der Druckereinstellungen ● Anzeigen von Informationen zur Fehlerbehebung ● Anzeigen der Online-Dokumentation Sie können HP Toolbox anzeigen, wenn der Drucker direkt an einen Computer oder an ein Netzwerk angeschlossen ist. Sie müssen eine vollständige Softwareinstallation durchführen, um HP Toolbox nutzen zu können.
So zeigen Sie HP Toolbox an 1. Öffnen Sie HP Toolbox auf eine der folgenden Weisen: Hinweis ● Doppelklicken Sie auf dem Windows-Desktop auf das Symbol für HP Toolbox. ● Klicken Sie im Startmenü von Windows auf Programme, und klicken Sie auf HP Toolbox. ● Klicken Sie unter Macintosh OS X auf der Festplatte auf Programme und dann auf den Ordner Dienstprogramme. Doppelklicken Sie auf das Symbol für die HP Toolbox.
Registerkarte "Fehlerbehebung" Die Registerkarte Fehlerbehebung bietet Verknüpfungen mit folgenden Hauptseiten: ● Hilfsmittel zur Druckqualität. Anzeige allgemeiner Informationen zur Fehlerbehebung, Anzeige von Informationen zur Fehlerbehebung von Problemen hinsichtlich der Druckqualität sowie Kalibrierung des Druckers zur Beibehaltung der Farbdruckqualität. ● Wartung.
Hinweis Wenn Sie den E/A-Verkehr im Netzwerk reduzieren möchten, stellen Sie die Häufigkeit für diese Option niedriger ein. Registerkarte "Dokumentation" Das Register Dokumentation enthält Verknüpfungen mit den folgenden Informationsquellen: ● Anmerkungen zur Installation. Stellt Ihnen vor Installation und Nutzung des Drucksystems spezifische Installationsanleitungen und Informationen zu Ihrem Produkt zur Verfügung. ● Benutzerhandbuch.
Deinstallieren von HP Toolbox In diesem Abschnitt wird das Deinstallieren von HP Toolbox erläutert. So deinstallieren Sie HP Toolbox unter Verwendung der Windows-Desktopverknüpfung 1. Klicken Sie auf Start. 2. Zeigen Sie auf Programme. 3. Zeigen Sie auf Hewlett-Packard oder auf die Programmgruppe HP LaserJet 2400 Serie, und klicken Sie auf HP LaserJet Toolbox deinstallieren. 4. Befolgen Sie die Anleitungen auf dem Bildschirm.
Verwalten und Konfigurieren von Druckertreibern Ihr System- oder Netzwerkadministrator kann mit der Treiberverwaltungs- und Konfigurationslösung die Druckertreiber konfigurieren, bevor Sie sie in Ihrer Umgebung installieren und implementieren. Dies ist nützlich, wenn Sie Druckertreiber für mehrere Workstations oder Drucker einstellen, die die gleiche Konfiguration aufweisen.
● Druckertreiber beschaffen. Sie können für jede an den Server angeschlossene Druckwarteschlange mehrere Treiber in Umgebungen installieren, die mehrere Betriebssysteme unterstützen. ● Konfigurationseditor ausführen (einige ältere Treiber unterstützen den Editor nicht). ● Die konfigurierten Druckertreiber auf dem oder den Servern implementieren. ● Die Benutzer auffordern, eine Verbindung zum Druckserver herzustellen.
Konfigurieren von E-Mail-Warnmeldungen Über HP Web JetAdmin oder den integrierten Webserver können Sie das System so konfigurieren, dass Sie bei Druckerproblemen alarmiert werden. Die Warnmeldungen sind EMail-Nachrichten, die an Ihr E-Mail-Konto oder die von Ihnen angegebenen Konten geschickt werden. Sie können folgende Informationen konfigurieren: ● Das zu überwachende Gerät (in diesem Fall den Drucker) ● Die zu empfangenden Warnmeldungen (z.B.
Einstellen der Echtzeituhr Sie können die Echtzeituhr zum Festlegen der Datums- und Uhrzeiteinstellungen verwenden. Die Datums- und Uhrzeitangaben werden gespeicherten Druckaufträgen angehängt, so dass die letzten Versionen gespeicherter Druckaufträge ermittelt werden können. Einstellen von Datum und Uhrzeit Wenn Sie Datum und Uhrzeit einstellen, können Sie Datumsformat, Datum, Uhrzeitformat und Uhrzeit festlegen. Einstellen des Datumsformats 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2.
Einstellen des Datums 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2. Blättern Sie mit (Taste NACH OBEN) oder (Taste NACH UNTEN) zu GERÄT KONFIGURIEREN, und drücken Sie (Taste AUSWÄHLEN). Hinweis 3. Blättern Sie mit (Taste NACH OBEN) oder und drücken Sie (Taste AUSWÄHLEN). (Taste NACH UNTEN) zu SYSTEM-SETUP, 4. Blättern Sie mit (Taste NACH OBEN) oder drücken Sie (Taste AUSWÄHLEN). (Taste NACH UNTEN) zu DATUM/ZEIT, und 5. Blättern Sie mit (Taste NACH OBEN) oder Sie (Taste AUSWÄHLEN).
Einstellen der Zeit 1. Drücken Sie MENÜ, um die Menüs zu öffnen. 2. Blättern Sie mit (Taste NACH OBEN) oder (Taste NACH UNTEN) zu GERÄT KONFIGURIEREN, und drücken Sie (Taste AUSWÄHLEN). 3. Blättern Sie mit (Taste NACH OBEN) oder und drücken Sie (Taste AUSWÄHLEN). (Taste NACH UNTEN) zu SYSTEM-SETUP, 4. Blättern Sie mit (Taste NACH OBEN) oder drücken Sie (Taste AUSWÄHLEN). (Taste NACH UNTEN) zu DATUM/ZEIT, und 5. Blättern Sie mit (Taste NACH OBEN) oder Sie (Taste AUSWÄHLEN).
Überprüfen der Druckerkonfiguration Über das Druckerbedienfeld können Sie Informationsseiten drucken, denen Sie detaillierte Angaben zum Drucker und dessen Konfiguration entnehmen können. Folgende Informationsseiten werden hier beschrieben: ● Menüstruktur ● Konfigurationsseite ● Verbrauchsmaterial-Statusseite ● PS- oder PCL-Schriftartenliste Eine vollständige Liste der Druckerinformationsseiten finden Sie im Menü INFORMATIONEN des Druckerbedienfelds (siehe Menü "Informationen").
2. Blättern Sie mit (Taste NACH OBEN) oder (Taste NACH UNTEN) zu INFORMATIONEN, und drücken Sie dann auf (Taste AUSWÄHLEN). 3. Blättern Sie mit (Taste NACH OBEN) oder (Taste NACH UNTEN) zu KONFIGURATION DRUCKEN, und drücken Sie dann auf (Taste AUSWÄHLEN). Es folgt ein Beispielausdruck einer Konfigurationsseite. Der Inhalt der Konfigurationsseite kann unterschiedlich sein und hängt von den derzeit im Drucker installierten Optionen ab.
5 Sicherheit Listet den Status der Druckerbedienfeldsperre, des BedienfeldPassworts und des Laufwerks (sofern eines im Drucker installiert ist) auf. 6 Papierfächer und Optionen Gibt die Formateinstellungen für alle Fächer sowie das installierte optionale Papierzufuhrzubehör an.
PS- oder PCL-Schriftartenliste Aus den Schriftartenlisten ersehen Sie, welche Schriftarten derzeit im Drucker installiert sind. In den Schriftartenlisten werden auch die Schriftarten aufgeführt, die sich auf einer optionalen Festplatte oder einem Flash-DIMM befinden. So drucken Sie eine PS- oder PCL-Schriftartenliste 1. Drücken Sie (Taste AUSWÄHLEN), um die Menüs zu öffnen. 2. Blättern Sie mit (Taste NACH OBEN) oder (Taste NACH UNTEN) zu INFORMATIONEN, und drücken Sie dann auf (Taste AUSWÄHLEN). 3.
Verwalten der Druckpatrone In diesem Abschnitt finden Sie Informationen zu HP Druckpatronen, deren Lebensdauer, die entsprechende Lagerung und darüber, wie Sie HP Originalverbrauchsmaterialien erkennen. Außerdem finden Sie auch Angaben zu Nicht-HP Druckpatronen.
VORSICHT Um eine Beschädigung der Druckpatrone zu vermeiden, setzen Sie sie niemals länger als einige Minuten dem Licht aus. Lebensdauer von Druckpatronen Die Lebensdauer der Druckpatrone hängt von der für Druckjobs benötigten Tonermenge und der Lebensdauer der Komponenten im Inneren der Patrone ab. Wenn Sie Text bei einer Deckung von 5 % drucken (typisch für Geschäftskorrespondenz), reicht eine Druckpatrone von HP für durchschnittlich 6.000 (Q6511A) oder 12.000 (Q6511X) Seiten.
"Patrone fast leer" und "Patrone leer" Wenn der Toner in der Druckpatrone fast oder vollständig verbraucht ist, werden Sie vom Drucker gewarnt. Wenn die Patrone nur wenig Toner enthält oder die Trommel fast verbraucht ist. Wenn die Patrone fast leer ist, wird auf dem Druckerbedienfeld die Meldung PATRONE BESTELLEN angezeigt. Die Meldung wird erstmalig angezeigt, wenn ca. 16% (6.000-SeitenPatrone) oder ca. 8% (12.000-Seiten-Patrone) Toner in der Druckpatrone verbleiben.
Reinigen des Druckers Im Laufe der Zeit sammeln sich Tonerpartikel und kleine Papierfetzen im Drucker an. Dies kann zu Druckqualitätsproblemen führen. Durch Reinigen des Druckers können Sie diese Probleme beseitigen oder zumindest vermindern. Reinigen Sie die Bereiche um den Papierpfad und die Druckpatrone bei jedem Reinigen der Druckerpatrone oder Auftreten von Qualitätsproblemen. Der Drucker sollte nach Möglichkeit von Staub und Schmutzpartikeln freigehalten werden.
4. Entfernen Sie mit einem trockenen fusselfreien Tuch alle Rückstände aus dem Bereich des Papierpfads und der Druckpatrone. 5. Setzen Sie die Druckpatrone wieder ein, und schließen Sie die obere Abdeckung. Hinweis Wenn das Wiedereinsetzen der Druckpatrone problematisch ist, achten Sie darauf, dass Sie die Einzugsplatte nach unten gedrückt und die Druckpatrone fest eingesetzt haben. 6. Stecken Sie das Netzkabel wieder ein, und schalten Sie den Drucker ein.
6. Befolgen Sie zum Abschließen des Reinigungsvorgangs die Anweisungen auf der Reinigungsseite. 7. Wenn das Druckermodell mit einem Duplexer ausgerüstet ist, schließen Sie das hintere Ausgabefach.
4 Problembehebung Über die vorliegenden Informationen zur Fehlerbehebung erhalten Sie Hilfe beim Lösen von Druckproblemen. Wählen Sie in der folgenden Liste das allgemeine Thema oder die allgemeine Art des Problems aus.
Ablaufdiagramm zur Fehlerbehebung Wenn beim Drucken Fehler auftreten, können Sie mithilfe des Ablaufdiagramms die Ursachen ermitteln. Wenn ein Schritt mit dem Drucker nicht durchgeführt werden kann, folgen Sie den entsprechenden Hinweisen zur Fehlerbehebung. Wenn Sie ein Problem auf die hier vorgeschlagene Weise nicht lösen können, wenden Sie sich an einen autorisierten HP Kundendienst- oder Serviceanbieter. (Weitere Informationen finden Sie unter HP Kundendienst.
● Schalten Sie den Drucker aus und dann wieder ein. ● Überprüfen Sie die Netzkabelanschlüsse und den Netzschalter. ● Schließen Sie den Drucker an eine andere Steckdose an. ● Überprüfen Sie, ob die Stromversorgung für den Drucker keinen Schwankungen unterliegt und den Anforderungen des Druckers entspricht (Weitere Informationen finden Sie unter Elektrische Eigenschaften.) ● Drücken Sie eine ● Taste auf dem Druckerbedienfeld, um festzustellen, ob der Drucker reagiert.
● Prüfen Sie, ob in allen Fächern ordnungsgemäß Papier eingelegt ist und ob alle Fächer richtig eingestellt und in den Drucker eingesetzt sind. ● Prüfen Sie am Computer die Druckwarteschlange und den Druckspooler, um festzustellen, ob der Drucker angehalten wurde. Wenn beim Drucken des aktuellen Druckjobs ein Problem auftritt oder der Drucker angehalten wurde, wird keine Konfigurationsseite gedruckt. (Drücken Sie STOPP, und führen Sie erneut Schritt 2 des Ablaufdiagramms zur Fehlerbehebung durch.
● Wenn der Job nicht gedruckt und in der Bedienfeldanzeige des Druckers eine Meldung angezeigt wird, finden Sie weitere Hinweise unter Interpretieren von Bedienfeld-meldungen. ● Prüfen Sie am Computer, ob der Drucker angehalten wurde. Drücken Sie STOPP, um fortzufahren. ● Wenn der Drucker in einem Netzwerk eingesetzt wird, prüfen Sie, ob Sie mit dem richtigen Drucker drucken.
4 Wird der Job wie erwartet gedruckt? JA Weiter mit Schritt 5. NEIN Der Druck ist unkenntlich, oder es wird nur ein Teil der Seite gedruckt. 102 Der Druckjob wird vorzeitig abgebrochen. Kapitel 4 Problembehebung Druckgeschwindigkeit ist langsamer als erwartet. Eine Einstellung des Druckerbedienfeldes wird nicht wirksam.
● ● Prüfen Sie, ob Sie den richtigen Druckertreiber verwenden. (Weitere Informationen finden Sie unter Verwenden des Druckertreibers.) Die zum Drucker gesendete Datendatei ist möglicherweise beschädigt. Drucken Sie diese Datei versuchsweise (wenn möglich) mit einem anderen Drucker, oder drucken Sie eine andere Datei. ● Prüfen Sie die Schnittstellenkabelverbindungen. Schließen Sie das Kabel versuchsweise an einem anderen Computer an (wenn möglich).
Der Druckjob ist nicht Das Papier wird falsch ordnungsgemäß formatiert. eingezogen oder ist beschädigt. Probleme mit der Druckqualität treten auf. ● ● Ändern Sie die Druckauflösung. (Weitere Informationen finden Sie unter Untermenü "Druckqualität".) ● Prüfen Sie, ob RET aktiviert ist. (Weitere Informationen finden Sie unter Untermenü "Druckqualität".) ● Wechseln Sie zu Beheben von Druckqualitätsproblemen. ● Prüfen Sie, ob Sie den richtigen Druckertreiber verwenden.
● Überprüfen Sie, ob Sie das ● richtige Fach ausgewählt haben. (Weitere Informationen finden Sie unter Auswählen der Papierzufuhr.) ● Stellen Sie sicher, dass Papierformat und -typ für die entsprechenden Fächer richtig konfiguriert sind. (Weitere Informationen finden Sie unter Einlegen von Druckmedien in die Fächer.) Drucken Sie eine Konfigurationsseite, in der die aktuellen Einstellungen für die Fächer angezeigt werden. (Weitere Informationen finden Sie unter Konfigurationsseite.
Beheben von allgemeinen Druckproblemen Weitere Informationen zu den in diesem Abschnitt aufgeführten Probleme und Lösungen finden Sie unter Fehlerbehebung von häufiger auftretenden Macintosh-Problemen (beim Verwenden eines Macintosh-Computers) und Fehlersuche bei häufiger auftretenden PostScript-Problemen (beim Verwenden des PS-Treibers). Drucker wählt Druckmedien aus dem falschen Fach aus. Mögliche Ursache Lösung Die Fachauswahl ist unter Umständen in der Softwareanwendung nicht korrekt eingestellt.
Das erste Blatt des Druckmediums staut sich im Bereich der Druckpatrone. Mögliche Ursache Lösung Hohe Luftfeuchtigkeit und hohe Temperatur beeinträchtigen die Medien. Passen Sie den Drucker an eine hohe Luftfeuchtigkeit und eine hohe Temperatur an. Druckjob erfolgt extrem langsam. Mögliche Ursache Lösung Der Job ist unter Umständen sehr komplex. Verringern Sie die Komplexität der Seite, oder passen Sie die Einstellungen für die Druckqualität an.
Der Druckjob enthält lediglich eine Seite, aber der Drucker verarbeitet auch die Rückseite der Seite (die Seite wird zur Hälfte aus dem Drucker heraus- und dann wieder eingezogen). Mögliche Ursache Lösung Der Drucker ist auf beidseitigen Druck eingestellt. Auch wenn der Druckjob nur eine Seite enthält, verarbeitet der Drucker auch die Rückseite. Informationen dazu, wie Sie die Einstellung ändern, finden Sie unter Ändern der Einstellungen für einen Druckjob oder in der Online-Hilfe.
Der Drucker reagiert nicht, wenn Sie in der Software Drucken auswählen. Mögliche Ursache Lösung Im Drucker sind keine Druckmedien mehr vorhanden. Legen Sie Druckmedien ein. Der Drucker arbeitet möglicherweise im manuellen Zufuhrmodus. Schalten Sie den Drucker aus dem manuellen Zufuhrmodus um. Das Kabel zwischen Computer und Drucker ist nicht richtig angeschlossen. Ziehen Sie das Kabel ab, und stecken Sie es anschließend wieder ein. Das Druckerkabel ist defekt.
Verwendungsrichtlinien für Papier Die besten Ergebnisse werden mit normalem, hochwertigem Papier erzielt, das keine Einschnitte, Löcher, Risse, Flecken, losen Partikel, Staubpartikel, Falten, Lücken sowie gerollten oder welligen Kanten aufweist. Wenn Sie nicht sicher sind, welchen Papiertyp Sie gerade verwenden (z.B. Schreibmaschinen- oder Recyclingpapier), finden Sie die entsprechenden Hinweise auf der Verpackung.
Hinweis Verwenden Sie kein Briefkopfpapier, das mit wärmeempfindlicher Tinte bedruckt wurde, wie sie beispielsweise bei einigen Arten der Thermografie verwendet wird. Verwenden Sie kein geprägtes Briefkopfpapier. Der Toner wird mit Hitze und Druck auf dem Papier fixiert. Farbiges Papier und vorgedruckte Formulare müssen deshalb mit einer Tinte bedruckt sein, die für diese Fixiertemperatur (210 °C bzw. 392 °F für 0,1 Sekunden) ausgelegt ist.
Drucken von Sonderseiten Innerhalb des Druckerspeichers befinden sich Sonderseiten, die Ihnen beim Erkennen und Verstehen allgemeiner Druckerprobleme weiterhelfen. ● Konfigurationsseite Die Konfigurationsseite listet viele der aktuellen Druckereinstellungen und eigenschaften auf. Informationen darüber, wie Sie die Konfigurationsseite drucken, finden Sie unter Konfigurationsseite.
Beseitigen von Staus Gelegentlich können beim Drucken Staus auftreten. Dafür gibt es z.B. folgende Ursachen: ● Nicht ordnungsgemäß geladene oder überfüllte Fächer. ● Fach 2 oder das Fach 3 wurde während des Druckjobs entfernt. ● Die obere Abdeckung wurde während des Druckjobs geöffnet. ● Die verwendeten Medien erfüllen die Spezifikationen von HP nicht (siehe Papierspezifikationen). ● Die verwendeten Druckmedien stammen nicht aus dem unterstützten Formatbereich (siehe Papierspezifikationen).
1. Öffnen Sie die obere Abdeckung. 2. Nehmen Sie die Druckpatrone heraus. VORSICHT Setzen Sie die Druckpatrone nicht länger als wenige Minuten direkter Lichteinstrahlung aus, um Beschädigungen zu vermeiden. Decken Sie die Patrone mit einem Blatt Papier ab, um sie vor Lichteinstrahlung zu schützen, solange sie sich nicht im Drucker befindet. 3. Heben Sie die Einzugsplatte vorsichtig an.
Hinweis Wenn das Wiedereinsetzen der Druckpatrone problematisch ist, achten Sie darauf, dass Sie die Einzugsplatte nach unten gedrückt und die Druckpatrone fest eingesetzt haben. Wenn die Achtung-LED nicht ausgeschaltet wird, befinden sich noch gestaute Medien im Drucker. Überprüfen Sie die Bereiche des Papiereinzugs und der hinteren Ausgabe auf Staus. Überprüfen Sie bei Druckern mit integriertem Duplexer den Duplexerbereich.
4. Bei Fach 2 drücken Sie den Stapel nach unten, bis die metallene Papieranhebeplatte einrastet. Schieben Sie beide Fächer in den Drucker. 5. Drücken Sie zum Zurücksetzen des Druckers und zum Fortsetzen des Druckvorgangs (Taste AUSWAHL). Hinweis Wenn die Achtung-LED nicht ausgeschaltet wird, befinden sich noch gestaute Medien im Drucker. Überprüfen Sie die Bereiche des Papiereinzugs und der hinteren Ausgabe auf Staus. Überprüfen Sie bei Druckern mit integriertem Duplexer den Duplexerbereich.
3. Wenn das Druckmedium vom oberen Ausgabefach aus fast vollständig zu sehen ist, ziehen Sie das restliche Medium vorsichtig aus dem Drucker. Wenn die Papierkante überhaupt nicht oder kaum im Druckpatronenbereich sichtbar ist, öffnen Sie das hintere Ausgabefach vollständig. Schieben Sie zu diesem Zweck die Fachabdeckung etwas nach vorne, und lösen Sie vorsichtig das Gitter. Drehen Sie das Staubeseitigungsrad, um die Medien aus dem Drucker herauszunehmen. 4. Installieren Sie die Druckpatrone neu.
2. Drücken Sie die grüne Taste an der rechten Vorderseite von Fach 2, um die Papierzugangsplatte zu öffnen. 3. Ziehen Sie das gestaute Papier heraus. 4. Schieben Sie die Unterseite der Papierzugangsplatten-Rückseite nach oben, bis sie auf beiden Seiten einrastet (beide Seiten müssen festsitzen). 5. Setzen Sie Fach 2 wieder ein. Hinweis 118 Wenn die Achtung-LED nicht ausgeschaltet wird, befinden sich noch gestaute Medien im Drucker.
Beschreibung der Druckermeldungen Auf der Bedienfeldanzeige des Druckers werden Meldungen zum normalen Status des Druckers (z.B. Verarbeitung...) oder einem Fehler (etwa OBERE ABDECKUNG SCHLIESSEN) angezeigt, der behoben werden muss. In Interpretieren von Bedienfeldmeldungen finden Sie eine Liste der gängigsten Meldungen, die beachtet werden müssen oder Fragen aufwerfen. Meldungen werden zunächst in alphabetischer Reihenfolge aufgelistet, wobei die Meldungen mit Zahlencode am Ende der Liste stehen.
Interpretieren von Bedienfeld-meldungen Bedienfeldmeldung Beschreibung Empfohlene Maßnahme 10.32.00 Vom Drucker wurde erkannt, dass es sich bei einem verwendeten Verbrauchsmaterial nicht um ein HP Originalverbrauchsmaterial handelt. Diese Meldung wird angezeigt, bis Sie ein HP Verbrauchsmaterial installieren oder auf die Taste zum Ignorieren drücken (Taste AUSWAHL). Dadurch könnte die Gewährleistung für den Drucker unwirksam werden. UNAUTOR.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme 21 SEITE ZU KOMPLEX Die zum Drucker gesendeten Daten (viel Text, Regeln, Raster- oder Vektorgrafiken) waren zu komplex. 1. Drücken Sie (Taste AUSWAHL), um die übertragenen Daten zu drucken (es könnten Daten verloren gehen). 2. Wenn diese Meldung häufiger angezeigt wird, vereinfachen Sie den Druckjob, oder installieren Sie weiteren Speicher. (Weitere Informationen finden Sie unter Druckerspeicher.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme 40 EIO X - FEHLERHAFTE Die Verbindung zwischen dem Drucker und der EIO-Karte im angegebenen Steckplatz [X] ist abgebrochen. Drücken Sie (Taste AUSWAHL), um die Fehlermeldung zu löschen und den Druckvorgang fortzusetzen. ÜBERTRAGUNG im Wechsel mit Zum Fortfahren drücken Sie 41.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme 51.XY FEHLER Es ist ein vorübergehender Druckerfehler aufgetreten. 1. Schalten Sie den Drucker aus und dann wieder ein. 2. Wird die Meldung weiterhin angezeigt, wenden Sie sich an einen autorisierten HP Service- und Supportanbieter (siehe HP Kundendienst). 1. Schalten Sie den Drucker aus und dann wieder ein. 2.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme 55.XX.YY DC Es ist ein vorübergehender Druckerfehler aufgetreten. 1. Schalten Sie den Drucker aus und dann wieder ein. 2. Wird die Meldung weiterhin angezeigt, wenden Sie sich an einen autorisierten HP Service- und Supportanbieter (siehe HP Kundendienst). Aufgrund einer falschen Zufuhr- oder Ausgabeanforderung ist ein vorübergehender Druckerfehler aufgetreten. 1.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme 59.XY FEHLER Es ist ein vorübergehender Druckerfehler aufgetreten. 1. Schalten Sie den Drucker aus und dann wieder ein. 2. Wird die Meldung weiterhin angezeigt, wenden Sie sich an einen autorisierten HP Service- und Supportanbieter (siehe HP Kundendienst). Diese Meldung weist darauf hin, dass kein System gefunden werden konnte. Das Softwaresystem des Druckers ist beschädigt. 1.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme 68.X SPEICHERFEHLER Im permanenten Speicher des Druckers ist ein Fehler aufgetreten, und eine oder mehrere Druckereinstellungen wurden auf die Werkseinstellungen zurückgesetzt. Drücken Sie (Taste AUSWAHL), um die Meldung zu löschen, und drücken Sie (Taste AUSWAHL), um den Druckvorgang fortzusetzen. EINSTELL.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme 79.XXXX FEHLER Es wurde ein schwer wiegender Hardwarefehler erkannt. 1. Drücken Sie STOPP, um den Druckjob aus dem Druckerspeicher zu löschen. Schalten Sie den Drucker aus und dann wieder ein. 2. Versuchen Sie, einen Druckjob von einer anderen Anwendung aus zu drucken. Wird der Druckjob gedruckt, versuchen Sie eine andere Datei von der ersten Anwendung aus zu drucken.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme 8X.YYYY Die EIO-Zubehörkarte hat einen schwer wiegenden Fehler festgestellt. 1. Schalten Sie den Drucker aus und dann wieder ein. 2. Schalten Sie den Drucker aus, setzen Sie das EIO-Zubehör wieder ein, und schalten Sie dann den Drucker wieder ein. 3. Setzen Sie das EIO-Zubehör wieder ein. Der integrierte HP Jetdirect-Druckserver hat einen schwer wiegenden Fehler festgestellt. 1.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme EINLEGEN IN FACH XX Ein Job wird abgesendet, für den ein bestimmter, in dem angegebenen Fach nicht vorhandener Typ und ein bestimmtes Format erforderlich sind. Legen Sie die angeforderten Medien in das angegebene Fach ein, und drücken (Taste AUSWAHL). Sie Ein Job wird abgesendet, für den ein bestimmter, in dem angegebenen Fach nicht vorhandener Typ und ein bestimmtes Format erforderlich sind.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme FACH XX OFFEN ODER Aus diesem Fach kann kein Papier in den Drucker eingezogen werden, da Fach [X] geöffnet ist und geschlossen werden muss, bevor der Druckvorgang fortgesetzt werden kann. Überprüfen Sie, ob Fächer geöffnet sind, und schließen Sie sie gegebenenfalls. Der Drucker hat den Typ und das Format der angeforderten Medien nicht erkannt.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme KARTENSTECKPLATZ X - Die CompactFlash-Karte in Steckplatz X ist voll. Löschen Sie Dateien von der CompactFlash-Karte, und versuchen Sie es dann erneut. Verwenden Sie zum Herunterladen oder Löschen von Dateien und Schriftarten den Device Storage Manager in der HP Web JetAdmin-Software. (Weitere Informationen finden Sie in der Hilfe zur HP Web JetAdmin-Software.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme MANUELLE ZUFUHR Die erste Seite eines manuellen Duplexjobs wurde gedruckt, und das Gerät wartet darauf, dass Sie den Ausgabestapel einlegen, damit die zweite Seite verarbeitet werden kann. 1. Legen Sie den Ausgabestapel in Fach 1, und behalten Sie die Ausrichtung mit der bedruckten Seite nach unten bei. 2.
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme PATRONE ERSETZEN Der untere Schwellenwert für die verbleibenden Seiten dieses Verbrauchsmaterials wurde erreicht. Der Drucker ist so eingestellt, dass das Drucken gestoppt wird, wenn ein Verbrauchsmaterial neu bestellt werden muss. Drücken Sie zum Fortsetzen des Drucks (Taste AUSWAHL), um die Druckermeldung zu beenden, und drücken Sie dann (Taste AUSWAHL).
Interpretieren von Bedienfeld-meldungen (Fortsetzung) Bedienfeldmeldung Beschreibung Empfohlene Maßnahme RAM-DISK- Die RAM-Disk ist voll. 1. Löschen Sie Dateien, und wiederholen Sie den Vorgang. Oder schalten Sie den Drucker aus und wieder ein. Dadurch werden alle im Gerät gespeicherten Dateien gelöscht. (Löschen Sie die Dateien mithilfe von Device Storage Manager in der HP Web JetAdminSoftware. 2. Wenn die Meldung weiterhin angezeigt wird, erhöhen Sie die Größe der RAM-Disk.
Beheben von Druckqualitätsproblemen In diesem Abschnitt werden unterschiedliche Probleme mit der Druckqualität und deren Behebung beschrieben. Häufig können Probleme mit der Druckqualität leicht behoben werden, wenn der Drucker ordnungsgemäß gewartet wird, Druckmedien gemäß den HP Spezifikationen verwendet werden oder eine Reinigungsseite gedruckt wird.
Informationen hierzu finden Sie unter Helles Druckbild (Teil der Seite). Informationen hierzu finden Sie unter Helles Druckbild (gesamte Seite). Informationen hierzu finden Sie unter Flecken. Informationen hierzu finden Sie unter Flecken. Informationen hierzu finden Sie unter Fehlstellen. Informationen hierzu finden Sie unter Grauer Hintergrund. Informationen hierzu finden Sie unter Verschmierter Toner. Aa BbCc Aa BbCc Aa BbCc Aa BbCc Aa BbCc Informationen hierzu finden Sie unter Fehlstellen.
Informationen hierzu finden Sie unter Verwischte Linien. Informationen hierzu finden Sie unter Unscharfer Druck. Informationen hierzu finden Sie unter Willkürliche Bildwiederholung (dunkel). Informationen hierzu finden Sie unter Willkürliche Bildwiederholung (hell). Helles Druckbild (Teil der Seite) 1. Überprüfen Sie, ob die Tonerpatrone richtig eingesetzt ist. 2. Möglicherweise ist der Tonerstand der Druckpatrone zu niedrig. Tauschen Sie die Druckpatrone aus. 3.
Flecken Nach dem Beheben von Papierstaus treten auf einer Seite möglicherweise Flecken auf. 1. Drucken Sie einige weitere Seiten. Eventuell wird das Problem auf diese Weise behoben. 2. Reinigen Sie die Innenseiten des Druckergehäuses, und drucken Sie eine Reinigungsseite, damit die Fixiereinheit gereinigt wird. (Weitere Informationen finden Sie unter Reinigen des Druckers.) 3. Verwenden Sie zum Drucken einen anderen Papiertyp. 4. Prüfen Sie, ob die Druckpatrone Risse aufweist.
2. Reinigen Sie die Innenseiten des Druckergehäuses, und drucken Sie eine Reinigungsseite, damit die Fixiereinheit gereinigt wird. (Weitere Informationen finden Sie unter Reinigen des Druckers.) 3. Tauschen Sie die Druckpatrone aus. Grauer Hintergrund 1. Verwenden Sie kein Papier, das bereits in den Drucker eingezogen und gedruckt wurde. 2. Verwenden Sie zum Drucken einen anderen Papiertyp. 3. Drucken Sie einige weitere Seiten. Eventuell wird das Problem auf diese Weise behoben. 4.
Loser Toner In diesem Zusammenhang sind lose Tonerpartikel dadurch definiert, dass sich der Toner durch Reiben von der gedruckten Seite löst. 1. Wenn Sie schweres oder raues Papier verwenden, öffnen Sie am Druckerbedienfeld das Menü GERÄT KONFIGURIEREN. Wählen Sie im Untermenü DRUCKQUALITÄT die Option FIXIERMODI und anschließend den verwendeten Papiertyp aus. Ändern Sie die Einstellung in HOCH 1 oder HOCH 2, wodurch der Toner besser auf dem Papier fixiert wird.
Sich wiederholende Druckbilder Dear Mr. Abhjerhjk, The dhjhfiuhu if teint hhkjhjnf j us a weue jd, fnk ksneh vnk kjdfkaakd ss hsjhnckkajhdhf kashfhnduujdn. Pkshkkhklhlkhkhyufwe4yrh9jjflkln djd skshkshdcnksnjcnal aksnclnslskjlncsl nas lnslna, ncnsljsjscljckn nsnclknsllj hwlsdknls nwljs nlnscl nijhsn clsncij hn. Iosi fsjs jlkh andjna this is a hn. jns fir stie a djakjd ajjssk. Thsi ius vnvlu tyeh lch afted, and when hghj hgjhk jdj a dt sonnleh. Suolklv jsdj hvjkrt ten sutc of jthjkfjkn vjdj hwjd, an olk d .
5. Vergewissern Sie sich, dass Typ und Qualität des verwendeten Papiers den HP Spezifikationen entsprechen. (Weitere Informationen finden Sie unter Papierspezifikationen.) 6. Vergewissern Sie sich, dass die Umgebungsspezifikationen für den Drucker eingehalten werden. (Weitere Informationen finden Sie unter Betriebsumgebung.) Wellen 1. Wenden Sie den Papierstapel im Fach. Drehen Sie das Papier ggf. um 180°. 2.
5. Vergewissern Sie sich, dass Typ und Qualität des verwendeten Papiers den HP Spezifikationen entsprechen. (Weitere Informationen finden Sie unter Papierspezifikationen.) 6. Wenn Umschläge beim Drucken verknittert werden, sollten die Umschläge so aufbewahrt werden, dass sie flach liegen. Vertikale weiße Linien 1. Drucken Sie einige weitere Seiten. Eventuell wird das Problem auf diese Weise behoben. 2. Vergewissern Sie sich, dass Typ und Qualität des verwendeten Papiers den HP Spezifikationen entsprechen.
2. Vergewissern Sie sich, dass Typ und Qualität des verwendeten Papiers den HP Spezifikationen entsprechen. (Weitere Informationen finden Sie unter Papierspezifikationen.) 3. Vergewissern Sie sich, dass die Umgebungsspezifikationen für den Drucker eingehalten werden. (Weitere Informationen finden Sie unter Betriebsumgebung.) 4. Tauschen Sie die Druckpatrone aus. Verwischte Linien 1. Vergewissern Sie sich, dass Typ und Qualität des verwendeten Papiers den HP Spezifikationen entsprechen.
5. Verringern Sie die Tonerdichte. Öffnen Sie über das Druckerbedienfeld das Menü GERÄT KONFIGURIEREN. Öffnen Sie das Untermenü DRUCKQUALITÄT und ändern Sie die Einstellung TONERDICHTE. (Weitere Informationen finden Sie unter Untermenü "Druckqualität".) 6. Öffnen Sie über das Druckerbedienfeld das Menü GERÄT KONFIGURIEREN. Öffnen Sie im Untermenü DRUCKQUALITÄT die Option OPTIMIEREN, und legen Sie TRANSFER HOCH=EIN fest. (Weitere Informationen finden Sie unter Untermenü "Druckqualität".
Fehlerbehebung bei allgemeinen Druckproblemen Hinweis 146 HP empfiehlt, den Drucker mit der Drucker-CD-ROM in einem Netzwerk zu installieren und einzurichten. ● Drucken Sie eine Konfigurationsseite (siehe Konfigurationsseite). Wenn ein HP JetdirectDruckserver installiert ist, wird mit der Konfigurationsseite eine zweite Seite ausgedruckt, die den Netzwerkstatus und die Netzwerkeinstellungen anzeigt.
Fehlerbehebung bei häufiger auftretenden Windows-Problemen Fehlermeldung: "Fehler beim Schreiben auf LPTx" in Windows 9x. DEWW Mögliche Ursache Lösung Es wurde kein Druckmedium eingelegt. Vergewissern Sie sich, dass Papier oder andere Druckmedien in die Fächer eingelegt sind. Das Kabel ist beschädigt oder locker. Vergewissern Sie sich, dass alle Kabel richtig angeschlossen sind, der Drucker eingeschaltet ist und die Bereit-LED leuchtet.
Fehlermeldung: "Allgemeine Schutzverletzung Ausnahme OE" "Spool32" "Ungültiger Vorgang" Mögliche Ursache Lösung Schließen Sie alle Softwareprogramme, starten Sie Windows neu, und versuchen Sie es erneut. Wählen Sie einen anderen Druckertreiber. Wenn der HP LaserJet 2400 Serie PCL 6-Treiber ausgewählt ist, wechseln Sie zu einem PCL 5eoder PS-Druckertreiber. Normalerweise können Sie dies in einem Softwareprogramm ändern. Löschen Sie alle temporären Dateien im Unterverzeichnis temp.
Fehlerbehebung von häufiger auftretenden Macintosh-Problemen Im folgenden Abschnitt werden Probleme aufgeführt, die über die unter Beheben von allgemeinen Druckproblemen aufgelisteten Probleme hinaus unter Mac OS 9.x oder Mac OS X auftreten können. Hinweis Die Einrichtung für den USB- und IP-Druck erfolgt über das Druckersymbole Dienstprogramm. Der Drucker wird in der Auswahl nicht angezeigt. Probleme unter Mac OS 9.
Probleme unter Mac OS 9.x (Fortsetzung) Ein Druckauftrag wurde nicht an den gewünschten Drucker gesendet. Mögliche Ursache Lösung Möglicherweise wurden die Druckaufträge in der Druckwarteschlange angehalten. Starten Sie die Druckaufträge in der Druckwarteschlange neu. Öffnen Sie das Menü Drucken in der oberen Menüleiste, und klicken Sie auf die Option zum Starten der Druckwarteschlange. Der falsche Druckername oder die falsche IP-Adresse wird verwendet.
Probleme unter Mac OS 9.x (Fortsetzung) Das Drucken mit der USB-Karte eines anderen Herstellers ist nicht möglich. Mögliche Ursache Lösung Dieser Fehler tritt auf, wenn die Software für USB-Drucker nicht installiert ist. Zum Hinzufügen der USB-Karte eines anderen Herstellers benötigen Sie unter Umständen die Apple USB Adapter Card Support-Software. Die aktuellste Version dieser Software können Sie von der Apple-Website herunterladen.
Probleme unter Mac OS X. Der Druckertreiber ist nicht im Print Center aufgeführt. Mögliche Ursache Lösung Möglicherweise wurde die Druckersoftware gar nicht oder nicht ordnungsgemäß installiert. Stellen Sie sicher, dass sich die PPD-Datei von HP LaserJet 2400 Serie im folgenden Festplattenordner befindet: Library/Printers/PPDs/Contents/Resources/ .lproj, wobei "" für den aus zwei Zeichen bestehenden Code der verwendeten Sprache steht. Installieren Sie die Software ggf. neu.
Probleme unter Mac OS X. (Fortsetzung) Der ausgewählte Drucker wird vom Druckertreiber nicht automatisch im Print Center eingerichtet. Mögliche Ursache Lösung Möglicherweise befindet sich der Drucker nicht im Bereitschaftsmodus. Vergewissern Sie sich, dass alle Kabel richtig angeschlossen sind, der Drucker eingeschaltet ist und die Bereit-LED leuchtet.
Probleme unter Mac OS X. (Fortsetzung) Eine EPS-Datei (Encapsulated PostScript) wird nicht mit den richtigen Schriftarten gedruckt. Mögliche Ursache Lösung Dieses Problem tritt bei einigen Programmen auf. ● Versuchen Sie, die in der EPS-Datei enthaltenen Schriftarten vor dem Drucken auf den Drucker zu laden. ● Senden Sie die Datei im ASCII-Format anstatt binär codiert. Das Drucken mit der USB-Karte eines anderen Herstellers ist nicht möglich.
Fehlersuche bei häufiger auftretenden PostScript-Problemen Die folgenden Situationen beziehen sich speziell auf die PostScript- (PS-)Sprache und treten unter Umständen dann auf, wenn mehrere Druckersprachen verwendet werden. Prüfen Sie, ob am Bedienfeld Meldungen angezeigt werden, die beim Lösen des Problems helfen.
Spezielle Fehler Grenzwertprüffehler Mögliche Ursache Lösung Der Druckjob war zu komplex. Sie müssen unter Umständen den Druckjob mit 600 dpi drucken, die Seite weniger komplex gestalten oder mehr Speicher installieren. VM-Fehler Mögliche Ursache Lösung Ein Schriftartenfehler ist aufgetreten. Wählen Sie im Druckertreiber die Option für eine unbegrenzte Anzahl ladbarer Schriftarten aus. Bereichsüberprüfung 156 Mögliche Ursache Lösung Ein Schriftartenfehler ist aufgetreten.
A Verbrauchsmaterial und Zubehör In diesem Abschnitt finden Sie Informationen zum Bestellen von Druckerteilen, Verbrauchsmaterial und Zubehör. Verwenden Sie nur speziell für diesen Drucker entwickelte Teile und Zubehör.
Bestellen von Druckerteilen, Zubehör und Verbrauchsmaterialien Es gibt mehrere Möglichkeiten, Druckerteile, Verbrauchsmaterialien und Zubehör zu bestellen: ● Direktbestellung bei HP ● Bestellen über Kundendienst oder Kundenunterstützung ● Direktes Bestellen über den integrierten Webserver (bei Druckern, die an ein Netzwerk angeschlossen sind) ● Direktbestellung über die Software HP Toolbox (für direkt an einen Computer angeschlossene Drucker) Direktbestellung bei HP Sie können Folgendes direkt bei H
5. Wählen Sie die gewünschten Teilenummern aus, und befolgen Sie die eingeblendeten Anweisungen. Direktbestellung über die Software HP Toolbox (für direkt an einen Computer angeschlossene Drucker) Mithilfe der Software HP Toolbox können Sie Verbrauchsmaterial und Zubehör direkt am Computer bestellen. Wenn Sie Verbrauchsmaterial über HP Toolbox bestellen möchten, klicken Sie auf Toolbox-Verknüpfungen und dann auf Verbrauchsmaterial bestellen.
Teilenummern Zum Zeitpunkt der Drucklegung war folgende Zubehörliste aktuell. Die Bestellinformationen und die Verfügbarkeit von Zubehör können sich während der Lebensdauer des Druckers ändern. Zubehör für die Papierzufuhr Artikel Beschreibung Teilenummer Optionales 500-Blatt-Fach und Zufuhr Optionales Fach, das die Papierkapazität vergrößert. Das Fach ist für die Formate Letter, A4, Legal, A5, B5 (JIS), Executive und 216 x 330 mm ausgelegt.
Kabel und Schnittstellen Artikel Beschreibung Teilenummer Erweiterte E/A-(EIO-)Karten HP Jetdirect 620n Fast Ethernet (10/100Base-TX)Druckserver J7934A Drahtloser interner Druckserver HP Jetdirect 680n 802.
Artikel Beschreibung Teilenummer HP Premium Choice LaserJetPapier Letter (216 x 279 mm), 500 Blatt/Ries, 10-Ries-Karton HPU1132/Nordamerika Hellstes HP LaserJet-Papier. Dieses außerordentlich glatte und makellos weiße Papier liefert Ausdrucke in unvergleichlichen Farbtönen und gestochen scharfem Schwarz. Ideal für Präsentationen, Geschäftspläne, externe Korrespondenz und andere Dokumente für hohe Qualitätsansprüche.
Artikel Beschreibung Teilenummer HP Büropapier Letter (216 x 279 mm), 500 Blatt/Ries, 10-Ries-Karton HPC8511/Nordamerika und Mexiko Letter (216 x 279 mm), dreifach gelocht, 500 Blatt/Ries, 10Ries-Karton HPC3HP/Nordamerika Letter (216 x 356 mm), 500 Blatt/Ries, 10-Ries-Karton HPC8514/Nordamerika Letter (216 x 279 mm), Quick Pack, 2.500-Blatt-Karton HP2500S/Nordamerika und Mexiko Letter (216 x 279 mm), Quick Pack, dreifach gelocht, 2.
164 Anhang A Verbrauchsmaterial und Zubehör DEWW
B Bedienfeldmenüs Die meisten routinemäßigen Druckaufgaben können in der entsprechenden Anwendung oder im Druckertreiber vom Computer ausgeführt werden. Anhand dieser beiden Methoden kann der Drucker auf einfache Weise gesteuert werden. Darüber hinaus werden dadurch die Einstellungen im Bedienfeld des Druckers außer Kraft gesetzt. Weiterführende Hinweise finden Sie in der Hilfe zur Anwendung. Weitere Informationen zum Öffnen des Druckertreibers erhalten Sie unter Verwenden des Druckertreibers.
Menü "Job wiederaufnehmen" Dieses Menü bietet eine Liste der im Drucker gespeicherten Jobs sowie Zugang zu allen Jobspeicherungsfunktionen. Sie können diese Jobs über das Bedienfeld des Druckers drucken oder löschen. Weitere Informationen zur Verwendung dieses Menüs finden Sie unter Verwenden der Jobspeicherungsfunktionen. Hinweis Wenn Sie den Drucker ausschalten, werden alle gespeicherten Jobs gelöscht. Im folgenden Abschnitt sind die Einstellungen sowie die möglichen Werte aufgeführt.
Problem Werte Erläuterung [BENUTZERNAME] [JOBNAME] Der Name der Person, die den Job gesendet hat. ALLE PRIVAT. JOBS KEINE GESPEICHERT. JOBS VORHANDEN [JOBNAME]: Der Name des im Drucker gespeicherten Jobs. Wählen Sie einen Job oder alle privaten Jobs aus, denen im Druckertreiber eine PIN zugewiesen wurde. ● Drucken: Der ausgewählte Job wird gedruckt.
Menü "Informationen" Dieses Menü enthält Druckerinformationsseiten mit Einzelheiten über den Drucker und dessen Konfiguration. Blättern Sie zur gewünschten Informationsseite, und drücken Sie auf (Taste AUSWÄHLEN). Problem Erläuterung MENÜSTRUKTUR DRUCKEN In der Menüstruktur werden das Layout und die aktuellen Einstellungen der Menüoptionen im Druckerbedienfeld dargestellt. Weitere Informationen finden Sie unter Menüstruktur.
Problem Erläuterung PS-SCHRIFTARTEN- In der PS-Schriftartenliste werden alle PSSchriftarten aufgeführt, die derzeit im Drucker verfügbar sind. Weitere Informationen hierzu finden Sie unter PS- oder PCL-Schriftartenliste.
Menü "Papierzufuhr" Wenn die Einstellungen für die Papierzufuhr im Druckerbedienfeld ordnungsgemäß konfiguriert sind, können durch Auswählen von Druckmedientyp und -format in der Anwendung oder im Druckertreiber Druckvorgänge ausgeführt werden. Weitere Informationen zum Konfigurieren von Druckmedientyp und -format finden Sie unter Drucken nach Medientyp und -format (Sperren von Fächern).
Option Werte Erläuterung FACH 1 TYP *BELIEBIGER TYP Mit dieser Option stellen Sie den Wert so ein, dass er dem Typ des Druckmediums, das in Fach 1 eingelegt ist, entspricht. NORMAL VORGEDRUCKT BRIEFKOPF TRANSPARENTFOLIE GELOCHT ETIKETTEN SCHREIBM.
Option Werte Erläuterung FACH 3 FORMAT *BELIEBIGE GRÖSSE Hiermit wird der Wert entsprechend des Formats des Druckmediums gesetzt, das derzeit in Fach 3 eingelegt ist. LETTER LEGAL EXECUTIVE A4 A5 B5 JIS EXECUTIVE (JIS) FACH 3 TYP *BELIEBIGER TYP NORMAL VORGEDRUCKT Hiermit wird der Wert entsprechend des Typs des Druckmediums gesetzt, das derzeit in Fach 3 eingelegt ist. BRIEFKOPF TRANSPARENTFOLIE GELOCHT ETIKETTEN SCHREIBM.
Option Werte Erläuterung Fach [N] Ben.def. MASSEINHEIT Diese Option wird nur angezeigt, wenn für ein Fach ein benutzerdefiniertes Format festgelegt wurde. BREITE LÄNGE MASSEINHEIT: Mit dieser Option können Sie die zu verwendende Maßeinheit (ZOLL oder MILLIMETER) auswählen, wenn für ein bestimmtes Fach benutzerdefinierte Papierformate eingestellt werden. BREITE: Mit dieser Option können Sie das Breitenmaß für das Papier einstellen (Maß von einer Seite des Fachs zur anderen).
Gerät konfigurieren, Menü Dieses Menü enthält administrative Funktionen. ● Untermenü "Drucken" ● Untermenü "Druckqualität" ● Untermenü "System Setup" ● Untermenü "E/A" ● Untermenü "Resets" Untermenü "Drucken" Einige Optionen in diesem Menü sind in der Anwendung oder im Druckertreiber verfügbar, falls der entsprechende Treiber installiert ist. Anwendungs- und Druckertreibereinstellungen setzen die Bedienfeldeinstellungen außer Kraft.
Artikel Werte Erläuterung STANDARD- *LETTER PAPIERFORMAT LEGAL Hier wird das Standardformat für Papier und Umschläge festgelegt. (Der Name der Option wechselt zwischen "Papier" und "Umschlag", wenn Sie durch die verfügbaren Formate blättern.) Diese Einstellung gilt nur für Druckjobs, für die in der Anwendung oder im Druckertreiber kein Papierformat angegeben wurde. EXECUTIVE STATEMENT 8.
Artikel Werte Erläuterung COURIER-SCHRIFT *NORMAL Hier kann die Version der zu verwendenden Courier-Schrift ausgewählt werden: DUNKEL NORMAL: Die interne Courier-Schrift, die auf den HP LaserJet 4 Series-Druckern verfügbar ist. DUNKEL: Die interne Courier-Schrift, die auf den HP LaserJet III Series-Druckern verfügbar ist. BREITES A4 *NEIN JA Mit dieser Einstellung wird die Anzahl der Zeichen geändert, die in einer Zeile auf A4-Papier gedruckt werden können.
Artikel Werte Erläuterung PCL EXEMPLARE EXEMPLARE: Hiermit kann der vertikale Abstand für Standardpapierformat zwischen 5 und 128 Zeilen eingestellt werden. AUSRICHTUNG SCHRIFTARTQUELLE SCHRIFTARTNUMMER ZEICHENDICHTE DER SCHRIFTART PUNKTGRÖSSE DER SCHRIFTART ZEICHENSATZ CR AN LF ANHÄNGEN LEERE SEITEN UNTERDRÜCKEN AUSRICHTUNG: Hier kann die Standardseitenausrichtung HOCHFORMAT oder QUERFORMAT ausgewählt werden.
Im folgenden Abschnitt sind die Einstellungen sowie die möglichen Werte aufgeführt. In der Wertespalte ist der Standardwert für jede Einstellung jeweils mit einem Sternchen (*) gekennzeichnet. Artikel Werte Erläuterung AUSRICHTUNG TESTSEITE DRUCKEN EINSTELLEN QUELLE Die Randausrichtung wird geändert, so dass das Druckbild auf der Seite horizontal und vertikal zentriert wird. Sie können auch das auf die Vorderseite gedruckte Druckbild am Druckbild auf der Rückseite ausrichten. JUST.
Artikel Werte Erläuterung FIXIERERMODI NORMAL Hiermit wird der Fixierermodus konfiguriert, der den einzelnen Medientypen zugeordnet ist. VORGEDRUCKT GELOCHT Ändern Sie den Fixierermodus nur, wenn Probleme beim Drucken auf bestimmten Medientypen auftreten. Nach der Auswahl eines Medientyps können Sie einen für diesen Typ verfügbaren Fixierermodus auswählen. Folgende Modi werden vom Drucker unterstützt: ETIKETTEN NORMAL: Wird für die meisten Papiertypen verwendet. SCHREIBM.
Artikel Werte Erläuterung RET AUS Mit Hilfe der Resolution Enhancement Technology (REt) werden Ausdrucke mit geglätteten Winkeln, Kurven und Kanten gewährleistet. HELL *MITTEL DUNKEL REt hat keine Auswirkungen auf die Druckqualität, wenn die Auflösung auf FastRes 1200 gesetzt ist. Alle anderen Druckauflösungen profitieren von REt. Hinweis Es empfiehlt sich, die REt-Einstellung in der Anwendung oder im Druckertreiber zu ändern.
Artikel Werte Erläuterung REINIGUNGSINTERVALL *1000 Hier wird das Intervall für die automatische Reinigung des Druckers eingestellt. 2000 5000 10000 20000 Untermenü "System Setup" Die Optionen in diesem Menü wirken sich auf die Funktionsweise des Druckers aus. Konfigurieren Sie den Drucker entsprechend Ihren Druckanforderungen. Im folgenden Abschnitt sind die Einstellungen sowie die möglichen Werte aufgeführt.
Artikel Werte Erläuterung FACH- ANGEFORDERTES FACH VERWENDEN ANGEFORDERTES FACH VERWENDEN: Hier wird festgelegt, ob Papier zuerst aus einem Fach eingezogen wird, das von dem im Druckertreiber ausgewählten Fach abweicht.
Artikel Werte Erläuterung DRUCKERSPRACHE *AUTOM. Hier kann die Standard-Druckersprache ausgewählt werden. Die möglichen Werte werden durch die im Drucker installierten gültigen Sprachen bestimmt. PDF PS PCL IGNORIERBARE *JOB MELDUNGEN EIN In der Regel sollte die Druckersprache nicht geändert werden.
Artikel Werte Erläuterung PATRONE STOPP LEER *WEITER Hiermit wird die Funktionsweise des Druckers festgelegt, wenn die Druckpatrone leer ist. STOPP: Der Druckvorgang wird unterbrochen und erst wieder gestartet, wenn die Druckpatrone ausgetauscht wurde. WEITER: Der Druckvorgang wird fortgesetzt, und die Meldung PATRONE ERSETZEN wird angezeigt, bis die Druckpatrone ausgetauscht wird.
Im folgenden Abschnitt sind die Einstellungen sowie die möglichen Werte aufgeführt. In der Wertespalte ist der Standardwert für jede Einstellung jeweils mit einem Sternchen (*) gekennzeichnet. Artikel Werte Erläuterung E/A-ZEITLIMIT 5 bis 300 (*15 SEKUNDEN) Legen Sie das E/A-Zeitlimit in Sekunden fest. Mit dieser Einstellung kann das Zeitlimit für optimale Leistung eingestellt werden. Erhöhen Sie den Wert für das Zeitlimit, wenn während des Druckjobs Daten von anderen Anschlüssen angezeigt werden.
Im folgenden Abschnitt sind die Einstellungen sowie die möglichen Werte aufgeführt. In der Wertespalte ist der Standardwert für jede Einstellung jeweils mit einem Sternchen (*) gekennzeichnet. Artikel Werte Erläuterung WERKSEINSTELLUNG WIEDERHERSTELLEN Kein Wert zur Auswahl vorhanden. Die Einstellungen werden zurückgesetzt und die meisten Werkseinstellungen (Standardeinstellungen) wiederhergestellt. Mit dieser Option wird auch der Eingabepuffer für die aktive Eingabe/Ausgabe gelöscht.
Menü "Diagnose" Administratoren können mithilfe dieses Untermenüs einzelne Komponenten isolieren und Papierstaus sowie Probleme der Druckqualität ermitteln und beheben. Im folgenden Abschnitt sind die Einstellungen sowie die möglichen Werte aufgeführt. In der Wertespalte ist der Standardwert für jede Einstellung jeweils mit einem Sternchen (*) gekennzeichnet. Option Werte Erläuterung EREIG.PROTOKOLL DRUCKEN Kein Wert zur Auswahl vorhanden.
Menü "Service" Das Menü "Service" ist gesperrt. Für den Zugriff auf dieses Menü ist eine PIN erforderlich. Dieses Menü sollte ausschließlich von Mitarbeitern der Kundenunterstützung verwendet werden.
C Spezifikationen HP LaserJet 2400 Serie Abmessungen und Gewicht Abmessungen des Produkts Produkt Höhe Tiefe Breite HP LaserJet 2410, 2420, 2420d, 2420n, 2420dn und 2430n 260 mm (10,2 Zoll) 400 mm (15,7 Zoll) 425 mm (16,7 Zoll) 15.2 kg (33,5 lb) Gewicht1 HP LaserJet 2430t, 2430tn und 2430dtn 400 mm (15,7 Zoll) 400 mm (15,7 Zoll) 425 mm (16,7 Zoll) 20.9 kg (46 lb) optionales 500-Blatt-Zufuhrfach 1 140 mm (5,5 Zoll) 400 mm (15,7 Zoll) 425 mm (15,7 Zoll) 5.
Elektrische Eigenschaften ACHTUNG! Die Netzspannung richtet sich nach dem Land/der Region, in dem bzw. in der der Drucker verkauft wird. Ändern Sie die Einstellung für die Betriebsspannung nicht. Dies kann zu Schäden am Drucker führen und die Produktgewährleistung ungültig machen. Netzanforderungen (HP LaserJet 2400 Serie) Modell 110-Volt-Modelle 230-Volt-Modelle Netzanforderungen 110-127 Volt (± 10 %) 220-240 Volt (± 10 %) 50/60 Hz (± 2 Hz) 50/60 Hz (± 2 Hz) 10.0 Ampere 5.
Geräuschemissionen Schallleistungs- und Schalldruckpegel1 (HP LaserJet 2400 Serie) Schallleistungspegel Nach ISO 9296 Beim Drucken2 (HP LaserJet 2410) LWAd= 6,6 Bel (A) [66 dB(A)] Beim Drucken2 (HP LaserJet 2420) LWAd= 6,7 Bel (A) [67 dB(A)] Beim Drucken2 (HP LaserJet 2430) LWAd= 6,8 Bel (A) [68 dB(A)] Bereitschaft (HP LaserJet 2410) im Wesentlichen nicht hörbar Bereitschaft (HP LaserJet 2420) im Wesentlichen nicht hörbar Bereitschaft (HP LaserJet 2430) im Wesentlichen nicht hörbar Schalldruck
Betriebsumgebung 192 Umgebungsbedingungen beim Drucken Lagerung/Standby Temperatur (Drucker und Druckpatrone) 15 ° bis 32,5 °C (59 ° bis 89 °F) -20 ° bis 40 °C (-4 ° bis 104 °F) Relative Luftfeuchtigkeit 10 % bis 80 % 10 % bis 90 % Anhang C Spezifikationen DEWW
Papierspezifikationen Vollständige Papierspezifikationen für alle HP LaserJet-Drucker finden Sie im HP LaserJet printer family print media guide (erhältlich unter http://www.hp.com/support/ljpaperguide).
Die Umgebungsbedingungen für die Papierlagerung sollten regelmäßig kontrolliert werden, um eine optimale Druckleistung sicherzustellen. Die Umgebung muss eine Temperatur von 20 bis 24 °C mit einer relativen Luftfeuchtigkeit von 45 bis 55 % aufweisen. Anhand der folgenden Richtlinien können Sie die jeweiligen Lagerungsbedingungen überprüfen: ● Das Papier soll möglichst bei Zimmertemperatur gelagert werden.
Umschläge mit doppelseitigen Säumen Briefumschläge mit doppelseitigen Säumen haben anstelle von diagonal verlaufenden Säumen an beiden Enden des Briefumschlags senkrechte Säume. Dieser Umschlagtyp zerknittert sehr leicht. Achten Sie darauf, dass sich der Saum vollständig bis zur Ecke des Briefumschlags erstreckt (siehe Abbildung).
Etiketten VORSICHT Um eine Beschädigung des Druckers zu vermeiden, sollten Sie nur Etiketten verwenden, die für den Gebrauch mit Laserdruckern geeignet sind. Um schwerwiegende Papierstaus zu verhindern, sollten Sie stets Fach 1 und das hintere Ausgabefach zum Drucken von Etiketten verwenden. Drucken Sie niemals mehr als einmal auf den gleichen Etikettenbogen und niemals auf teilweise gebrauchte Etikettenbögen.
D Druckerspeicher und Speichererweiterung In diesem Abschnitt werden die Speicherfunktionen des Druckers sowie Schritte zur Erweiterung erläutert.
Überblick Der Drucker wird mit einem bereits installierten DIMM-Modul (Dual Inline Memory Module) geliefert. Es stehen ein zusätzlicher DIMM-Steckplatz sowie zwei CompactFlash-Steckplätze zur Verfügung. Damit können Sie den Drucker mit folgendem Zubehör erweitern: ● Mehr Druckerspeicher – es sind DIMM-Module mit 32, 48, 64, 128 und 256 MB erhältlich.
Druckerspeicher Es ist ratsam, die Speicherkapazität des Druckers zu erweitern, wenn Sie oft komplexe Grafiken oder PostScript-Dokumente (PS) drucken oder viele in den Drucker geladene Schriftarten verwenden. Mit hinzugefügtem Speicher erhalten Sie außerdem eine größere Flexibilität für Jobspeicherungsfunktionen, z.B. Schnellkopien. So fügen Sie Druckerspeicher hinzu VORSICHT DIMMs können durch statische Elektrizität beschädigt werden.
3. Entfernen Sie die rechte seitliche Abdeckung, indem Sie sie zur Rückseite des Druckers schieben, bis Sie sie abnehmen können. 4. Ziehen Sie die Zugangsklappe an der Metalllasche auf. 5. Nehmen Sie das DIMM aus der antistatischen Verpackung. VORSICHT 200 Um einen Schaden durch statische Elektrizität zu verhindern, tragen Sie stets ein antistatisches Armband, oder berühren Sie die Oberfläche der antistatischen Verpackung, bevor Sie die DIMMs anfassen.
6. Halten Sie das DIMM-Modul an den Seitenkanten fest, und richten Sie die Einkerbungen am Modul am DIMM-Steckplatz aus. (Stellen Sie sicher, dass die Sperren an beiden Seiten des DIMM-Steckplatzes geöffnet, d.h. nach außen gerichtet sind.) 7. Drücken Sie das DIMM fest und gerade in den Steckplatz. Vergewissern Sie sich, dass die Verriegelungen an beiden Seiten des DIMMs einrasten. Hinweis Lösen Sie zum Herausnehmen eines DIMM-Moduls zunächst die Verriegelungen. 8.
9. Befestigen Sie die seitliche Abdeckung wieder am Drucker. Richten Sie dazu die Ausrichtungspfeile aufeinander aus, und schieben Sie die Abdeckung zur Vorderseite des Druckers, bis die Zungen der Abdeckung in die entsprechenden Schlitze des Druckers einrasten. 10. Stecken Sie die Schnittstellenkabel und das Netzkabel wieder ein. 11. Schalten Sie den Drucker ein.
Installieren von CompactFlash-Karten Es können bis zu zwei CompactFlash-Karten zur Erweiterung des Druckers um Schriftarten installiert werden. So installieren Sie eine CompactFlash-Karte 1. Schalten Sie nach dem Drucken der Konfigurationsseite den Drucker aus, und ziehen Sie das Netzkabel ab. 2. Ziehen Sie alle Schnittstellenkabel ab. 3. Entfernen Sie die rechte seitliche Abdeckung, indem Sie sie zur Rückseite des Druckers schieben, bis Sie sie abnehmen können. 4.
5. Nehmen Sie die neue CompactFlash-Karte aus der Verpackung. 6. Halten Sie die CompactFlash-Karte am Rand fest, und richten Sie die Kerben in der Seite der Karte an den Markierungen im CompactFlash-Kartensteckplatz aus. 7. Schieben Sie die CompactFlash-Karte in ihre Position. 8. Schließen Sie die Zugangsklappe, und drücken Sie sie fest, bis sie einrastet. 9. Befestigen Sie die seitliche Abdeckung wieder am Drucker.
10. Stecken Sie die Schnittstellenkabel und das Netzkabel wieder ein. Verwenden Sie zur Verwaltung von Schriftarten den Device Storage Manager in HP Web JetAdmin. Weitere Informationen finden Sie in der Hilfe von HP Web JetAdmin.
Überprüfen der DIMM- oder CompactFlash-Installation Überprüfen Sie nach der Installation des DIMM-Moduls oder der CompactFlash-Karte, ob die Installation erfolgreich war. So überprüfen Sie, ob DIMM-Module oder CompactFlashKarten ordnungsgemäß installiert sind 1. Schalten Sie den Drucker ein. Überprüfen Sie, ob die Bereitschaftsanzeige leuchtet, nachdem der Startvorgang abgeschlossen ist.
Speichern von Ressourcen (permanente Ressourcen) Dienstprogramme oder Jobs, die Sie zum Drucker übertragen haben, beinhalten manchmal Ressourcen (beispielsweise Schriftarten, Makros oder Füllmuster). Intern als permanent gekennzeichnete Ressourcen bleiben so lange im Druckerspeicher, bis Sie den Drucker ausschalten. Beachten Sie die folgenden Richtlinien, wenn Sie Ressourcen über die PDL (Page Description Language, Seitenbeschreibungssprache) als permanent kennzeichnen.
Installieren einer EIO-Karte Gehen Sie zum Installieren einer EIO-Karte wie folgt vor. So installieren Sie eine EIO-Karte 1. Schalten Sie den Drucker aus. 2. Lösen Sie die beiden Schrauben, und entfernen Sie die Abdeckplatte vom EIOSteckplatz an der Rückseite des Druckers. Hinweis Werfen Sie die Schrauben oder die Abdeckplatte nicht weg. Heben Sie sie für zukünftigen Gebrauch auf, wenn Sie die EIO-Karte herausnehmen. 3.
So entfernen Sie installierte EIO-Karten 1. Schalten Sie den Drucker aus. 2. Lösen Sie die beiden Schrauben von der EIO-Karte, und entnehmen Sie die EIO-Karte aus dem EIO-Steckplatz. 3. Legen Sie die Abdeckplatte des EIO-Steckplatzes auf die Rückseite des Druckers. Setzen Sie die beiden Schrauben ein, und ziehen Sie sie fest. 4. Schalten Sie den Drucker ein.
210 Anhang D Druckerspeicher und Speichererweiterung DEWW
E Druckerbefehle Bei den meisten Anwendungen müssen Sie keine Druckerbefehle eingeben. Ziehen Sie gegebenenfalls die Computer- und Softwaredokumentation zu Rate, um Hinweise zum Eingeben von Druckerbefehlen zu erhalten. Hinweis DEWW PCL 6 und PCL 5e Über PCL 6- und PCL 5e-Druckerbefehle wird dem Drucker mitgeteilt, welche Aufgaben auszuführen und welche Schriftarten zu verwenden sind.
Die PCL 6- und PCL 5e-Druckerbefehlssyntax Bevor Sie Druckerbefehle verwenden, vergleichen Sie folgende Zeichen: Kleines l: l Großes O: O Ziffer Eins: 1 Ziffer 0: 0 In vielen Druckerbefehlen werden das kleine l (l) und die Ziffer Eins (1) oder das große O (O) und die Ziffer Null (0) verwendet. Auf dem Bildschirm sehen diese Zeichen unter Umständen anders aus als in den Beispielen in diesem Handbuch.
Verwenden von Escape-Zeichen Druckerbefehle beginnen immer mit dem Escape-Zeichen (Ec). In der nachstehenden Tabelle ist aufgeführt, wie das Escape-Zeichen in verschiedenen MSDOS-Anwendungen eingefügt werden kann. MS-DOS-Programm Eingabe Anzeige Lotus 1-2-3 und Symphony Geben Sie \027 ein. 027 Microsoft Word für MS-DOS Halten Sie die Alt-Taste gedrückt, und geben Sie auf dem Ziffernblock 027 ein. WordPerfect für MS-DOS Geben Sie <27> ein.
Hinweis Schriftarten haben entweder "feste" oder "proportionale" Zeichenabstände. Der Drucker verfügt sowohl über Schriftarten mit festem Zeichenabstand (Courier, Letter Gothic und Lineprinter) als auch über Schriftarten mit proportionalem Zeichenabstand (CGTimes, Arial‚ Times New Roman und andere). Schriftarten mit festem Zeichenabstand werden im Allgemeinen in Anwendungen wie Tabellenkalkulationen und Datenbanken verwendet, bei denen es wichtig ist, Spalten senkrecht aneinander auszurichten.
Seitensteuerungsbefehle (Fortsetzung) Funktion Befehl Optionen (#) Papierformat Ec&l#A 1 = Executive 2 = Letter 3 = Legal 25 = A5 26 = A4 45 = JIS B5 80 = Briefumschlag Monarch 81 = Briefumschlag Commercial 10 90 = Briefumschlag DL ISO 91 = Briefumschlag C5 ISO 100 = Briefumschlag B5 ISO/ B5 ISO 101 = benutzerdefiniert Papiertyp Ec&n# 5WdBond = Schreibmaschinenpapier 6WdPlain = Normalpapier 6WdColor = farbiges Papier 7WdLabels = Etiketten 9WdRecycled = Recyclingpapier 11WdLetterhead = Briefkopfpapie
Seitensteuerungsbefehle (Fortsetzung) Funktion Befehl Optionen (#) Horizontaler Bewegungsindex Ec&k#H Schritte von 1/120 Zoll (das Druckbild wird in horizontaler Richtung komprimiert) Vertikaler Bewegungsindex Ec&l#C Schritte von 1/48 Zoll (das Druckbild wird in vertikaler Richtung komprimiert) Zeilenabstand Ec&l#D # = Zeilen pro Zoll (1, 2, 3, 4, 5, 6, 12, 16, 24, 48) Überspringen der Perforation Ec&l#L 0 = deaktivieren (ausschalten) 1 = aktivieren (einschalten) 1 Ersetzen Sie für benutzerd
Sprachenauswahl Funktion Befehl Optionen (#) Aufrufen des PCL 6- oder PCL 5-Modus Ec%#A 0 = vorherige PCL 5Cursorposition verwenden 1 = aktuelle HP-GL/2Stiftposition verwenden Aktivieren des HP-GL/2-Modus Ec%#B 0 = vorherige HP-GL/2Stiftposition verwenden 1 = aktuelle PCL 5Cursorposition verwenden Schriftartenauswahl Funktion Befehl Optionen (#) Zeichensätze Ec(# 8U = HP Roman-8-Zeichensatz 10U = IBM Layout (PC-8) (Codepage 437) Standardzeichensatz 12U = IBM Layout für Europa (PC-850) (Codepag
Schriftartenauswahl (Fortsetzung) Funktion Befehl Optionen (#) Primäre Strichstärke Ec(s#B 0 = mittel (Buch oder Text) 1 = halbfett 3 = fett 4 = sehr fett Schrifttyp Ec(s#T Drucken Sie eine PCL 6- oder PCL 5-Schriftartenliste, damit der jeweilige Befehl für die einzelnen internen Schriftarten aufgeführt wird. 1 Die bevorzugte Methode liegt in der Verwendung des Befehls für die primäre Zeichendichte.
F Behördliche Bestimmungen Einleitung Dieser Abschnitt enthält die folgenden behördlichen Bestimmungen: DEWW ● FCC-Bestimmungen ● Umweltschutz-Förderprogramm ● Konformitätserklärung ● Laser safety statement ● Canadian DOC statement ● Korean EMI statement ● Finnish laser statement Einleitung 219
FCC-Bestimmungen Dieses Gerät wurde typengeprüft und entspricht den Grenzwerten für Digitalgeräte der Klasse B gemäß Abschnitt 15 der Vorschriften der US-Funk- und Fernmeldebehörde (Federal Communications Commission, FCC). Diese Grenzwerte sorgen für einen angemessenen Schutz vor schädlichen Störungen beim Betrieb des Geräts in Wohngebieten. Dieses Gerät erzeugt und verwendet Hochfrequenzenergie und kann Hochfrequenzstrahlungen abgeben.
Umweltschutz-Förderprogramm Schutz der Umwelt Hewlett-Packard hat sich zum Ziel gesetzt, umweltverträgliche Qualitätsprodukte herzustellen. Dieser Drucker wurde unter besonderer Beachtung möglichst geringer Auswirkungen auf die Umwelt entworfen. Erzeugung von Ozongas Dieser Drucker erzeugt keine nennenswerten Ozonmengen (O3). Energieverbrauch Im PowerSave-Modus (Energiesparmodus) wird der Energieverbrauch beträchtlich herabgesetzt.
Druckzubehör für den HP LaserJet In vielen Ländern/Regionen kann Verbrauchsmaterial für dieses Produkt (zum Beispiel Tonerpatronen, Trommeln und Fixiereinheiten) über das HP Umweltprogramm für Verbrauchsmaterial an HP zurückgegeben werden. Dieses einfache und kostenfreie Rücknahmeprogramm wird in über 30 Ländern/Regionen angeboten. Mehrsprachige Programminformationen und Anweisungen finden Sie in der Verpackung neuer Tonerpatronen und anderen Verbrauchsmaterials für den HP LaserJet.
Typ Lithium-Carbon-Monofluorid (BR1632), 3 Volt, Knopfzellenbatterie, 1,5 g Material Quecksilberfrei, kadmiumfrei Ort Auf Leiterplatte Durch Benutzer zu entfernen Nein Weitere Recyclinginformationen finden Sie unter http://www.hp.com/recycle. Außerdem können Sie sich an die örtlichen Behörden oder an die Electronics Industry Alliance wenden: http://www.eiae.org.
Konformitätserklärung Konformitätserklärung nach ISO/IEC-Richtlinie 22 und EN 45014 Name des Herstellers: Adresse des Herstellers: Hewlett-Packard Company 11311 Chinden Boulevard, Boise, Idaho 83714-1021, USA erklärt, dass dieses Produkt Produktname: Modellzulassungsnummer3): Produktoptionen: HP LaserJet 2410/2420/2430-Drucker BOISB-0406-00 Einschließlich zusätzlichem optionalem 500-Blatt-Eingabefach (Q5963A) ALLE den folgenden Produktspezifikationen entspricht: Sicherheit: IEC 60950:1999/EN60950: 2000
Länder-/regionsspezifische Sicherheitserklärungen Laser safety statement Das Center for Devices and Radiological Health (CDRH) der US-amerikanischen Food and Drug Administration hat Vorschriften für Laserprodukte erlassen, die nach dem 1. August 1976 hergestellt wurden. Diese Vorschriften sind für alle in den USA vertriebenen Produkte verbindlich.
Finnish laser statement LASERTURVALLISUUS LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT HP LaserJet 2410, 2420 und 2430 Serien -laserkirjoitin on käyttäjän kannalta turvallinen luokan 1 laserlaite. Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen ulkopuolelle. Laitteen turvallisuusluokka on määritetty standardin EN60825-1 (1994) mukaisesti.
G Service und Support EINGESCHRÄNKTE GEWÄHRLEISTUNG VON HEWLETTPACKARD HP PRODUKT HP LaserJet 2410, 2420 und 2430 Serien GEWÄHRLEISTUNGSZEITRAUM 1 Jahr, Rückgabe an HP Kundendienstzentrale Hewlett-Packard gewährleistet für den oben angegebenen Zeitraum ab Abnahme durch den Endbenutzer, dass die HP Hardware und Zubehörteile frei von Material- und Verarbeitungsfehlern sind.
IM RAHMEN DER ÖRTLICH GÜLTIGEN GESETZGEBUNG SIND DIE IN DIESER GEWÄHRLEISTUNGSERKLÄRUNG ENTHALTENEN RECHTSMITTEL DIE EINZIGEN UND AUSSCHLIESSLICHEN RECHTSMITTEL DES KUNDEN.
Druckpatronen – Eingeschränkte Gewährleistungserklärung Es wird gewährleistet, dass diese HP Druckpatrone frei von Material- und Verarbeitungsfehlern ist.
Verfügbarkeit von Service und Support Hewlett-Packard bietet weltweit eine Vielzahl von Service- und Supportleistungen für den Verkauf an. Die Verfügbarkeit dieses Angebots hängt vom Standort des Kunden ab. HP Wartungsverträge Hewlett-Packard bietet mehrere Arten von Wartungsverträgen an, die eine breite Palette von Unterstützungsanforderungen abdecken. Wartungsverträge sind nicht Bestandteil der Standardgewährleistung. Die Supportleistungen sind je nach Standort verschieden.
HP Expressaustausch (nur USA und Kanada) Dieser Service ist gegen einen Aufpreis erhältlich. Er stellt eine Alternative zur Standardgewährleistung dar und umfasst die Rückgabe eines Druckers zu Reparaturzwecken. Über den HP Expressaustausch erhalten Sie während der Reparaturphase des defekten Druckers ein generalüberholtes Ersatzgerät.
Wiederverpacken des Druckers Wenn die HP Kundendienstzentrale feststellt, dass der Drucker zu Reparaturzwecken an HP zurückgegeben werden muss, führen Sie die folgenden Schritte aus, um den Drucker für den Transport zu verpacken. VORSICHT Transportschäden, die auf unangemessene Verpackung zurückzuführen sind, fallen in die Verantwortung des Kunden. So verpacken Sie den Drucker 1. Entnehmen Sie die gekauften und von Ihnen im Drucker installierten DIMMs oder CompactFlash-Karten, und bewahren Sie sie auf.
Service-Informationsformular WER GIBT DAS GERÄT ZURÜCK? Datum: Ansprechpartner: Telefon: Alternativer Ansprechpartner: Telefon: Rücksendeadresse: Spezielle Versandanweisungen: WAS WIRD VERSENDET? Modellbezeichnung: Modellnummer: Seriennummer: Legen Sie aussagekräftige Druckausgaben bei. Versenden Sie KEIN Zubehör, das für die Durchführung der Reparatur nicht benötigt wird (Handbücher, Reinigungsmaterialien usw.).
Rechnungsadresse: 234 Anhang G Service und Support Spezielle Rechnungsanweisungen: DEWW
Index Symbole/Zahlen "Ungültiger Vorgang"-Fehler 148 1.
Beide Seiten, Drucken Einstellungen für die Bindungsrichtung 175 beide Seiten, drucken auf Fehlerbehebung 107 Beidseitiges Drucken Layoutoptionen 57 manuell 58 Papier einlegen 56 unterstützte Papierformate 56 Verbrauchsseite 168 Verwenden des Duplexers 57 Benutzerdefinierte Papierformat Facheinstellungen 175 Benutzerdefiniertes Papierformat Bedrucken von 53 Einstellungen 64, 173 Fachspezifikationen 36 Benutzerhandbuch 79 Bereichsüberprüfung, Fehlerbehebung 156 Bereit-LED 11 Bestellen Druckmedien, HP 161 Bes
einlegen 44 Fachauswahl 14, 182 Facheinstellungen 170 Fehlerbehebung 110 Fixierermodi 43 gelocht 54 HP, bestellen 161 Kapazität 4 kleinformatig 53 kleinformatige, Einstellungen 180 Lagerung 193 mehrere Seiten auf einem Blatt drucken 64 PCL-Befehle 214 PS-Einstellungen 16 Quelle, auswählen 66 Spezifikationen 36, 193 Standardformat, festlegen 175 unterstützte Formate 36, 37 Verbrauchsseite 168 vorgedruckt 54 Welle, Fehlerbehebung 106 Druckpatronen bestellen iii Economode 65 EconoMode 180 fast leer 19, 183 Fül
Ereignisprotokoll 88, 187 Erweiterter Service iv Escape-Zeichen 212 Ethernet-Karten, Teilenummern 161 Etiketten drucken 52 Fixierermodi 179 Spezifikationen 196 Exemplare, Standardanzahl 174 Explorer, unterstützte Versionen HP Toolbox 76 HP Web Jetadmin 75 integrierter Webserver 72 Expressaustausch, HP 231 F Fach 1 Drucken aus 14, 182 Duplexdruck 56 Einstellungen 170 Einstellungen für benutzerdefinierte Formate 175 Einstellungen für manuelle Zufuhr 15, 175 Fehlerbehebung 104 manueller Duplexdruck 58 manuelle
Fehler bei Wiederholung Bilder 145 Fehlermeldungen Einstellungen 18, 183 Ereignisprotokoll 187 Ereignisprotokoll, drucken 88 Windows 147 Fehlermeldungen, Fehlerbehebung 119 Fehlstellen, Fehlerbehebung 138 Fenster "Geräteeinstellungen", HP Toolbox 79 Festplatte Dateiverzeichnis, drucken 168 EIO-Steckplätze 198 installieren 208 Schriftartenliste, drucken 90 Fixiereinheit, reinigen 95 Fixierer Modi 179 Fixierermodi 43 Flecken, Fehlerbehebung 138, 143 Format, Papier Duplexerspezifikationen 37 Fachauswahl 40, 41
öffnen 77 Registerkarte "Benachrichtigungen" 78 Registerkarte "Dokumentation" 79 Registerkarte "Fehlerbehebung" 78 Registerkarte "Status" 77 Verknüpfungen 79 HP Web Jetadmin Download 75 E-Mail-Warnmeldungen 83 Treiberkonfiguration 81 unterstützte Browser 75 I IBM OS/2-Treiber 24 Ignorierbare Meldungen Anzeigedauer einstellen 18 Ignorierbare Meldungen, Einstellungen 18, 183 Informationsseiten, drucken 87 Installation Treiber, die das Dienstprogramm für die benutzerdefinierte Installation verwenden 82 Install
LaserJet-Dienstprogramm, Macintosh 28 laser safety statements 225 LEDs, Bedienfeld 11 Leere Seiten unterdrücken 177 leere Seiten, Fehlerbehebung 108 Legal-Papier, abgeschnittene Ränder 155 Leistungsaufnahme 6 Leitfaden zur Inbetriebnahme 2 Letter-Papier, A4-Einstellungen ignorieren 175 Letzte Seite, anderes Papier 67 Linien, Fehlerbehebung 138 loser Toner abwaschen 113 loser Toner, Fehlerbehebung 140 LPT-Fehlermeldungen 147 Luftfeuchtigkeitsanforderungen 192 M Macintosh AppleTalk-Einstellungen 185 Drucken i
P Papier A4-Einstellungen 175, 176 benutzerdefiniertes Format 64, 175 Benutzerdefiniertes Format, drucken 53 Deckblätter 67 Duplexdruck, unterstützte Formate 56 Duplexerspezifikationen 37 einlegen 44 Fachauswahl 14, 40, 41, 182 Facheinstellungen 170 Fehlerbehebung 110 Fehlerbehebung bei Fächern 106 Fixierermodi 43, 179 gelocht 54 gewellt 142 HP, bestellen 161 Kapazität 4 kleinformatig 53 kleinformatiges, Einstellungen 180 Lagerung 193 manuelle Zufuhr 42 mehrere Seiten auf einem Blatt drucken 64 PCL-Befehle
Siehe auch Treiber PS-Verzögerung von Druckmedien, Einstellung 16 Punkte, Fehlerbehebung 138, 143 Q Qualität Fehlerbehebung 135 Quecksilber-Spezifikationen 222 Quelle, Papier 66 Querformat als Standardeinstellung festlegen 177 Optionen für Duplexdruck 57 PCL-Befehle 215 R RAM-Disk-Einstellungen 21, 184 Ränder Briefumschläge 195 Legal-Papier, Fehlerbehebung 155 PCL-Befehle 215 Umschläge 50 Ränder, Einstellungen 178 Randlosdruck 175 Raues Papier Fixierermodi 179 Rechte seitliche Abdeckung 8 Recycling Druckpat
Netzwerkinstallation, Windows 29 unter Macintosh installieren 32 unterstützte Betriebssysteme 23 unter Windows installieren 29 Software entfernen Macintosh 35 Windows 34 Spannungseigenschaften 190 Speicher erweitern 198 Installation überprüfen 206 Installieren von DIMMs 199 Jobspeicheranforderungen 68 Konfigurationsseite 88 Lieferumfang 5 permanente Ressourcen 207 RAM-Disk-Einstellungen 21, 184 Speicher, Job Einstellungen 181 Speichererweiterung 198 Speichern, Job Menü "Job wiederaufnehmen" 166 privat 69 pr
Teilenummern Druckmedien, HP 161 EIO-Karten 161 Kabel 161 Telefonnummern Kundenunterstützung iii Serviceverträge iv Verbrauchsmaterial bestellen iii Temperaturanforderungen 192 Tests 187 Text, Fehlerbehebung unkenntlich 108 Textqualität, Fehlerbehebung 141, 144 Toner abwaschen 113 Ausgabequalität, Fehlerbehebung 139 EconoMode 180 fast leer 19, 183 Festlegen der Tonerdichte 180 leer 20, 184 Toner, sparen 65 Toner abwaschen 113 Tonerdichte, Einstellungen 180 Toner fast leer 19 Toner leer 20, 184 Tonerpatronen
Wartung Verträge 230 Wartungsverträge iv, 230 Wasserzeichen, drucken 63 Webbrowseranforderungen HP Toolbox 76 integrierter Webserver 72 Web Jetadmin Download 75 E-Mail-Warnmeldungen 83 Treiberkonfiguration 81 unterstützte Browser 75 Websites Fälschungsschutz 91 HP Web Jetadmin, Download 75 Kundenunterstützung iii Macintosh-Kundenunterstützung iv Papierspezifikationen 193 Serviceverträge iv Software herunterladen iii UNIX- und Linux-Treiber 24 Verbrauchsmaterial bestellen iii weiße Linien oder Spritzer, Fehl
© 2004 Hewlett-Packard Development Company, LP www.hp.com/support/lj2410 www.hp.com/support/lj2420 www.hp.