Getting Started HP Notebook
© Copyright 2011 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ..................................................................................................................... 4 Top ....................
Using the embedded numeric keypad ............................................................... 24 Turning the embedded numeric keypad on and off .......................... 25 Switching key functions on the embedded numeric keypad ............. 25 Using an optional external numeric keypad ...................................................... 25 Using pointing devices .......................................................................................................................
Using f11 recovery tools .................................................................................... 53 Using a Windows Vista operating system DVD (purchased separately) ........... 54 8 Customer support ......................................................................................................................................... 55 Contacting customer support ............................................................................................................. 55 Labels ..........
viii
1 Welcome ● Finding information After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, refer to Networking on page 15. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer and includes a limited subscription for free updates.
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about Quick Setup poster ● How to set up the computer ● Help to identify computer components Getting Started guide ● Computer features To access this guide: ● How to connect to a wireless network specifications Select Start > Help and Support > User Guides.
Resources For information about Safety & Comfort Guide ● Proper workstation setup, posture, health, and work habits To access this guide: ● Electrical and mechanical safety information Select Start > Help and Support > User Guides. – or – Select Start > All Programs > HP > HP Documentation. – or – Go to http://www.hp.com/ergo. Worldwide Telephone Numbers booklet HP support telephone numbers This booklet is provided with your computer.
2 4 Getting to know your computer ● Top ● Front ● Right ● Left ● Display ● Bottom Chapter 2 Getting to know your computer
Top TouchPad Component Description (1) TouchPad on/off button Turns the TouchPad on and off. (2) TouchPad Moves the pointer and selects or activates items on the screen. (3) Left TouchPad button Functions like the left button on an external mouse. (4) Right TouchPad button Functions like the right button on an external mouse.
Lights Component (1) (2) Description Power light QuickWeb light ● On: The computer is on. ● Blinking: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. ● On: The computer is on. ● Off: The computer is off or in Hibernation. NOTE: For more information, refer to “HP QuickWeb” in this guide and to the HP QuickWeb software Help.
Buttons and fingerprint reader (select models only) Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component (2) Description QuickWeb button ● When the computer is off or in Hibernation, press the button to open HP QuickWeb. ● When the computer is in Microsoft Windows, press the button to open the default Web browser. ● When the computer is in HP QuickWeb, press the button to open the default Web browser. NOTE: For more information, refer to “HP QuickWeb” in this guide and to the HP QuickWeb software Help.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (3) Start key Displays the Start menu. (4) Function keys Execute frequently used system functions when pressed in combination with the fn key. (5) Menu key Displays the active programs's shortcut menu (same as the right-click menu).
Front Component Description (1) ● Blinking white: The hard drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. (2) Drive light Media Card Reader Supports the following digital card formats: ● Memory Stick Pro ● Memory Stick Duo Pro ● MultiMediaCard ● MultiMediaCard Micro ● Secure Digital (SD) Card ● Secure Digital (SD) Card Micro (3) Speakers (2) Produce sound.
Right Component (1) Description AC adapter light ● White: The computer is connected to external power and the battery is 90 to 99% charged. ● Amber: The computer is connected to external power and the battery is 0 to 90% charged. ● Blinking amber: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly. ● Off: The battery is fully charged.
Left Component (1) Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (2) RJ-11 (modem) jack (select models only) Connects a modem cable. (3) Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.
Display Component Description (1) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide-area networks (WWAN). (2) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (3) Internal microphone(s) (1 or 2 depending on model) Record sound. (4) Webcam light (select models only) On: The webcam is in use. (5) Webcam (select models only) Records video and captures still photographs.
Bottom Component Description (1) Battery and access cover release latches Release the battery from the battery bay, and release the access cover from the computer. (2) Battery bay Holds the battery. (3) SIM slot Contains a wireless subscriber identity module (SIM) (select models only). The SIM slot is located inside the battery bay. (4) Vents (2) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.
3 Networking ● Using an Internet service provider (ISP) ● Connecting to a wireless network NOTE: Internet hardware and software features vary depending on computer model and your location. Your computer may support one or both of the following types of Internet access: ● Wireless—For mobile Internet access, you can use a wireless connection. Refer to Connecting to an existing WLAN on page 17 or Setting up a new WLAN network on page 17.
Using an Internet service provider (ISP) Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service. NOTE: Your ISP will give you a user ID and password to access the Internet. Record this information and store it in a safe place.
Connecting to an existing WLAN 1. Turn on the computer. 2. Be sure that the WLAN device is on. 3. Click the network icon in the notification area, at the far right of the taskbar. 4. Select a network to connect to. 5. Click Connect. 6. If required, enter the security key.
Configuring a wireless router For help in setting up a WLAN, refer to the information provided by your router manufacturer or your ISP. The Windows operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network: ● Windows 7—Select Start > Control Panel > Network and Internet > Network and Sharing Center > Set up a new connection or network > Set up a network. Then follow the on-screen instructions.
4 HP QuickWeb Getting started The HP QuickWeb environment provides a fun and engaging way to perform many of your favorite activities. Your computer is ready to go within seconds of turning it on, allowing you to rapidly access the Internet, widgets, and communication programs. Simply press the QuickWeb button on your computer, and then start browsing the Internet, communicating with Skype, and exploring other HP QuickWeb programs.
Starting HP QuickWeb ● To start HP QuickWeb, press the QuickWeb button when the computer is off or in Hibernation. The following table explains the different behaviors of the QuickWeb button. Button Bahavior QuickWeb button ● When the computer is off or in Hibernation, opens HP QuickWeb. ● When the computer is in Microsoft Windows, opens the default Web browser. ● When the computer is in HP QuickWeb, opens the default Web browser.
5 Keyboard and pointing devices ● Using the keyboard ● Using pointing devices 21
Using the keyboard Identifying the hotkeys A hotkey is a combination of the fn key (1) and either the esc key (2) or one of the function keys (3). To use a hotkey: ▲ Briefly press the fn key, and then briefly press the second key of the hotkey combination. Hotkey combination Description fn+esc Displays system information. fn+f1 Initiates Sleep, which saves your information in system memory. The display and other system components turn off and power is conserved.
Hotkey combination fn+f4 Description Switches the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, fn+f4 alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor. Most external monitors receive video information from the computer using the external VGA video standard.
Using keypads The computer includes either an embedded numeric keypad or an integrated numeric keypad. The computer also supports an optional external numeric keypad or an optional external keyboard that includes a numeric keypad. Using the embedded numeric keypad (1) Component Description fn key Turns the embedded numeric keypad on and off when pressed in combination with the num lk key.
Turning the embedded numeric keypad on and off Press fn+num lk to turn on the embedded numeric keypad. Press fn+num lk again to turn off the keypad. NOTE: The embedded numeric keypad is turned off while an external keyboard or numeric keypad is connected to the computer.
Using pointing devices NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased separately) by connecting it to one of the USB ports on the computer. Setting pointing device preferences Use Mouse Properties in Windows to customize settings for pointing devices, such as button configuration, click speed, and pointer options. To access Mouse Properties: Windows 7—Select Start > Devices and Printers.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad light. NOTE: The TouchPad light is off when the TouchPad is on. Navigating To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
Selecting Use the left and right TouchPad buttons like the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To view the demonstration of a gesture: 1. Right-click the Synaptics icon in the notification area, at the far right of the taskbar, and then click TouchPad Properties. 2.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. NOTE: Two-finger scrolling is enabled at the factory. Pinching/Zooming Pinching allows you to zoom in or out on images or text. ● Zoom in by placing two fingers together on the TouchPad, and then moving them apart.
6 30 Maintenance ● Inserting or removing the battery ● Using the optional security screw ● Replacing or upgrading the hard drive ● Adding or replacing memory modules ● Updating programs and drivers ● Using SoftPaq Download Manager ● Cleaning your computer Chapter 6 Maintenance
Inserting or removing the battery NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide. To insert the battery: ▲ Insert the battery (1) into the battery bay until it is seated (2). The battery release latches automatically lock the battery into place. To remove the battery: CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information.
2. 32 Slide the battery up (2), and remove the battery from the battery bay (3).
Using the optional security screw Use the optional security screw to lock the access cover to the bottom of the computer. When not in use the security screw can be stored inside the battery bay. To use the security screw: 1. Remove the battery. CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and initiate Hibernation or shut down the computer through Windows before removing the battery. 2.
Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. Removing the hard drive 34 1.
8. Lift the hard drive (3) out of the hard drive bay.
Installing a hard drive 1. Insert the hard drive into the hard drive bay (1). 2. Replace the four hard drive screws (2), and then connect the hard drive connector to the system board (3). 3. Align the tabs on the access cover with the notches on the computer (1), and then slide the cover in to close it (2). The release latches automatically lock the access cover (3).
4. Replace the security screw (4), if desired. For additional information on the security screw, refer to Using the optional security screw on page 33. 5. Replace the battery. 6. Connect AC power and external devices to the computer. 7. Turn on the computer. Adding or replacing memory modules The computer has two memory module compartments.
CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before adding or replacing memory modules. Do not remove a memory module while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. 1. Save your work and shut down the computer. 2.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 8. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 9. Align the tabs on the access cover with the notches on the computer (1), then slide the cover in to place (2). The release latches automatically lock the access cover into place (3).
10. Replace the security screw (4), if desired. For additional information on the security screw, refer to Using the optional security screw on page 33. 11. Replace the battery. 12. Connect AC power and external devices to the computer. 13. Turn on the computer.
Updating programs and drivers HP recommends that you update your programs and drivers on a regular basis with the latest versions. Go to http://www.hp.com/support to download the latest versions. You can also register to receive automatic update notifications when they become available.
Using SoftPaq Download Manager HP SoftPaq Download Manager (SDM) is a tool that provides quick access to SoftPaq information for HP business computers without requiring the SoftPaq number. Using this tool, you can easily search for SoftPaqs, and then download and unpack them. SoftPaq Download Manager works by reading and downloading, from the HP FTP site, a published database file containing computer model and SoftPaq information.
Cleaning your computer ● Cleaning products ● Cleaning procedures Cleaning products Use the following products to safely clean and disinfect your notebook or tablet PC: ● Dimethyl benzyl ammonium chloride 0.3 percent maximum concentration (For example: germicidal disposable wipes. These wipes come in a variety of brand names.
Cleaning the TouchPad and keyboard CAUTION: When cleaning the TouchPad and keyboard, do not let liquids drip between the keys. This can permanently damage internal components. ● To clean and disinfect the TouchPad and keyboard, use a soft microfiber cloth or chamois moistened with one of the cleaning solutions listed previously or use an acceptable germicidal disposable wipe.
7 Backup and recovery Windows 7 ● Backing up your information ● Performing a system recovery To protect your information, use Windows Backup and Restore to back up individual files and folders, back up your entire hard drive (select models only), create system repair discs (select models only) by using the installed optical drive (select models only) or an optional external optical drive, or create system restore points.
new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. The system repair discs (select models only) are used to start up (boot) the computer and repair the operating system in case of system instability or failure. Your initial and subsequent backups allow you to restore your data and settings if a failure occurs. You can back up your information to an optional external hard drive, a network drive, or discs.
Using the Windows recovery tools To recover information you previously backed up: 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to recover your system settings, your computer (select models only), or your files. To recover your information using Startup Repair, follow these steps: CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive.
3. If the HP Recovery partition is listed, restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 4. Press f11 while the “Press for recovery” message is displayed on the screen. 5. Follow the on-screen instructions. Using a Windows 7 operating system DVD (purchased separately) To order a Windows 7 operating system DVD, go to http://www.hp.
Windows Vista To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
Backing up your information Recovery after a system failure is as complete as your most current backup. You should create your initial backup immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. You can back up your information to an optional external hard drive, a network drive, or discs.
Performing a recovery In case of system failure or instability, the computer provides the following tools to recover your files: ● Windows recovery tools: You can use the Backup and Restore Center to recover information you have previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows from starting correctly. ● f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image.
Using f11 recovery tools CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled. Personal files must be restored from a backup.
Using a Windows Vista operating system DVD (purchased separately) To order a Windows Vista operating system DVD, go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. You can also order the DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet included with the computer. CAUTION: Using a Windows Vista operating system DVD completely erases hard drive contents and reformats the hard drive.
8 Customer support ● Contacting customer support ● Labels Contacting customer support If the information provided in this user guide, in the HP Notebook Reference Guide, or in Help and Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support. The serial number label is affixed inside the battery bay.
9 Specifications ● Input power ● Operating environment Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz.
Operating environment Factor Metric U.S.
Index A AC adapter light 11 access cover removing 38 replacing 36, 40 security screw 33 access cover release latches 14 audio-in (microphone) jack 10 audio-out (headphone) jack 10 B Backup and Restore 47 Backup and Restore Center 50, 51 battery bay 14, 56 battery release latches 14 battery, replacing 31 Bluetooth label 56 buttons left TouchPad 5 power 7 QuickWeb 8 right TouchPad 5 TouchPad on/off 5 wireless 8 C caps lock light, identifying 6 caring for your computer 44 Certificate of Authenticity label cle
regulatory 56 serial number 56 SIM 56 wireless certification 56 WLAN 56 latches access cover 14 battery 14 lights AC adapter 11 caps lock 6 drive 10 power 6 QuickWeb 6 webcam 13 wireless 6 HDMI 12 USB 11, 12 USB charging 11 power button, identifying 7 power connector, identifying power light 6 Product Key 56 product name and number, computer 56 Q QuickWeb button, identifying 8 QuickWeb light 6 M Media Card Reader, identifying 10 media controls, keys 23 memory module inserting 39 removing 38 replacing 37
