User Guide
© Copyright 2014 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel, Celeron, Centrino, and Pentium are trademarks of Intel Corporation in the U.S. and other countries. Java is a U.S. trademark of Sun Microsystems, Inc. Microsoft and Windows are U.S. registered trademarks of the Microsoft group of companies. The information contained herein is subject to change without notice.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice ENWW
Processor configuration setting (select models only) IMPORTANT: Select computer models are configured with an Intel® Pentium® N35xx series or a Celeron® N28xx/N29xx series processor and a Windows® operating system. If your computer is configured as described, do not change the processor configuration setting in msconfig.exe from 4 or 2 processors to 1 processor. If you do so, your computer will not restart. You will have to perform a factory reset to restore the original settings.
vi Processor configuration setting (select models only) ENWW
Table of contents 1 Welcome ........................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ......................................................................................................................... 5 Right .............
Connecting to a wired network ........................................................................................................... 27 Connecting to a local area network (LAN) ......................................................................... 27 4 Navigating using the keyboard, touch gestures and pointing devices ............................................................ 29 Using pointing devices .................................................................................................
Connect displays to computers with AMD graphics (with an optional hub) ....... 47 Connect displays to computers with Intel graphics (with an optional hub) ........ 47 Connect displays to computers with Intel graphics (with a built-in hub) ............ 48 Discovering and connecting Miracast-compatible wireless displays (select models only) ................................................................................................................................... 48 6 Power management .................
Connecting a USB device .................................................................................................. 62 Removing a USB device .................................................................................................... 62 Using optional external devices .......................................................................................................... 62 Using optional external drives .......................................................................................
Using the fingerprint reader (select models only) ............................................................................... 82 Locating the fingerprint reader ........................................................................................... 82 10 Maintenance ................................................................................................................................................. 83 Adding or replacing memory modules .....................................................
13 Support ....................................................................................................................................................... 101 Contacting support ........................................................................................................................... 101 Labels ............................................................................................................................................... 102 14 Specifications .........................
1 Welcome After you set up and register the computer, we recommend the following steps to get the most out of your smart investment: TIP: To quickly return to the computer Start screen from an open app or the Windows desktop, press the Windows key on your keyboard. Pressing the Windows key again will return you to the previous screen. ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, see Connecting to a network on page 21.
Finding information You have already used Setup Instructions to turn on the computer and locate this guide. To locate resources that provide product details, how-to information, and more, use this table. Resources For information about Setup Instructions poster ● How to set up the computer ● Help to identify computer components HP Support Assistant ● Operating system information To access HP Support Assistant, from the Start screen, select the HP Support Assistant app.
Resources For information about Limited Warranty* Warranty information To access this guide, from the Start screen, select the HP Support Assistant app, select My computer, and then select Warranty and services. – or – Go to http://www.hp.com/go/orderdocuments. *You can find the expressly provided HP Limited Warranty applicable to your product located with the user guides on your computer and/or on the CD/DVD provided in the box.
4 Chapter 1 Welcome ENWW
2 Getting to know your computer Right NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Audio-out (headphone)/Audio-in (microphone) jack Connects optional powered stereo speakers, headphones, earbuds, a headset, or a television audio cable. Also connects an optional headset microphone. This jack does not support optional microphone-only devices.
Component (4) Description USB 3.0 port(s) Connects an optional USB device, such as a keyboard, mouse, external drive, printer, scanner or USB hub. For details about different types of USB ports, see Using a USB device on page 61. (5) RJ-45 (network) jack/lights Connects a network cable. ● Green (left): The network is connected. ● Amber (right): Activity is occurring on the network. (6) Docking connector Connects an optional docking device. (7) Power connector Connects an AC adapter.
Component ENWW Description (4) Memory card reader Reads optional memory cards that store, manage, share, or access information. (5) RJ-45 (network) jack/lights Connects a network cable. ● Green (left): The network is connected. ● Amber (right): Activity is occurring on the network. (6) Docking connector Connects an optional docking device. (7) Power connector Connects an AC adapter.
Left NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (2) Vents Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.
Component (1) Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (2) Vents Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Display NOTE: Your computer may look slightly different from the illustration in this section. Component Description (1) WLAN antennas* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) WWAN antennas* (select models only) Send and receive wireless signals to communicate with wireless wide area networks (WWAN). (3) Internal microphones Record sound. (4) Webcam light On: The webcam is in use. (5) Webcam Records video and captures photographs.
Top TouchPad Component Description (1) Pointing stick Moves the pointer and selects or activates items on the screen. (2) Left pointing stick button Functions like the left button on an external mouse. (3) TouchPad on/off button Turns the TouchPad on and off. (4) TouchPad zone Reads your finger gestures to move the pointer or activate items on the screen. NOTE: The TouchPad also supports edge-swipe gestures. For more information, see Edge swipes (select models only) on page 34.
Lights NOTE: Your computer may look slightly different from the illustration in this section. Component (1) Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state, a powersaving state. The computer shuts off power to the display and other unneeded components. ● Off: The computer is off or in Hibernation. Hibernation is a power-saving state that uses the least amount of power.
Component (6) Description Wireless light On: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. NOTE: On some models, the wireless light is amber when all wireless devices are off. (7) ENWW Mute light ● Amber: Computer sound is off. ● Off: Computer sound is on.
Buttons, speakers, and fingerprint reader (select models only) Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component ENWW Description (3) Wireless button Turns the wireless feature on or off but does not establish a wireless connection. (4) Volume mute button Mutes and restores speaker sound. (5) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a password logon.
Keys NOTE: Your computer may look slightly different from the illustration in this section. Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (3) Windows key Returns you to the Start screen from an open app or the Windows desktop. NOTE: Pressing the Windows key again will return you to the previous screen.
Bottom NOTE: Your computer may look slightly different from the illustration in this section. Component Description (1) Accessory battery connector (select models only) Connects an optional accessory battery. (2) Service door Provides access to the hard drive bay, the wireless LAN (WLAN) module slot, the WWAN module slot, and the memory module slots.
Component (5) Description Vents (2) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (6) 18 SIM slot (select models only) Chapter 2 Getting to know your computer Supports a wireless subscriber identity module (SIM). The SIM slot is located inside the battery bay.
Front Component (1) Description Wireless light On: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. NOTE: On some models, the wireless light is amber when all wireless devices are off. (2) Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state, a power-saving state. The computer shuts off power to the display and other unneeded components. ● Off: The computer is off or in Hibernation.
20 Chapter 2 Getting to know your computer ENWW
3 Connecting to a network Your computer can travel with you wherever you go. But even at home, you can explore the globe and access information from millions of websites using your computer and a wired or wireless network connection. This chapter will help you get connected to that world. Connecting to a wireless network Wireless technology transfers data across radio waves instead of wires.
The wireless light indicates the overall power state of your wireless devices, not the status of individual devices. If the wireless light is white, at least one wireless device is on. If the wireless light is off, all wireless devices are off. NOTE: On some models, the wireless light is amber when all wireless devices are off. Because the wireless devices are enabled at the factory, you can use the wireless button to turn on or turn off the wireless devices simultaneously.
Setting up a WLAN To set up a WLAN and connect to the Internet, you need the following equipment: ● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an Internet service provider ● A wireless router (2) (purchased separately) ● A wireless computer (3) NOTE: Some modems have a built-in wireless router. Check with your ISP to determine what type of modem you have.
Wireless encryption uses security settings to encrypt and decrypt data that is transmitted over the network. For more information, access HP Support Assistant. To access HP Support Assistant, from the Start screen, select the HP Support Assistant app. Connecting to a WLAN To connect to the WLAN, follow these steps: 1. Be sure that the WLAN device is on. If the device is on, the wireless light is on. If the wireless light is off, press the wireless button.
● HSPA (High Speed Packet Access), which provides access to networks based on the Global System for Mobile Communications (GSM) telecommunications standard. ● EV-DO (Evolution Data Optimized), which provides access to networks based on the code division multiple access (CDMA) telecommunications standard. ● LTE (Long Term Evolution), which provides access to networks supporting LTE technology. You may need the HP Mobile Broadband Module serial number to activate mobile broadband service.
7. Insert the SIM into the SIM slot, and gently push the SIM into the slot until it is firmly seated. NOTE: The SIM in your computer may look slightly different from the illustration in this section. NOTE: See the image on the battery bay to determine which way the SIM card should be inserted into your computer. 8. Replace the battery. NOTE: 9. HP Mobile Broadband will be disabled if the battery is not replaced. Reconnect external power. 10. Reconnect external devices. 11. Turn on the computer.
Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network (PAN) of Bluetooth devices. For information about configuring and using Bluetooth devices, see the Bluetooth software Help. Connecting to a wired network There are 2 kinds of wired connections: local area network (LAN) and modem connection. A LAN connection uses a network cable and is much faster than a modem, which uses a telephone cable. Both cables are sold separately.
28 Chapter 3 Connecting to a network ENWW
4 Navigating using the keyboard, touch gestures and pointing devices Your computer allows navigation using touch gestures (select models only) in addition to the keyboard and mouse. Touch gestures can be used on your computer TouchPad or on a touch screen (select models only). Select computer models have special action keys or hot key functions on the keyboard to perform routine tasks.
Using pointing devices NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased separately) by connecting it to one of the USB ports on the computer. Setting pointing device preferences Use Mouse Properties in Windows to customize settings for pointing devices, such as button configuration, click speed, and pointer options. You can also view demonstrations of TouchPad gestures.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off button. Tapping To make an on-screen selection, use the Tap function on the TouchPad. ● ENWW Tap one finger on the TouchPad zone to make a selection. Double-tap an item to open it.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. ● Place two fingers slightly apart on the TouchPad zone and then drag them up, down, left, or right. 2-finger pinch zoom 2-finger pinch zoom allows you to zoom out or in on images or text. 32 ● Zoom in by placing two fingers together on the TouchPad zone and then moving your fingers apart. ● Zoom out by placing two fingers apart on the TouchPad zone and then moving your fingers together.
2-finger click 2-finger click allows you to make menu selections for an object on the screen. NOTE: ● Using 2-finger click is the same action as using right-click with the mouse. Place two fingers on the TouchPad zone and press to open the options menu for the selected object. Rotating (select models only) Rotating allows you to turn items such as photos. ● Anchor the forefinger of your left hand in the TouchPad zone.
Flicking (select models only) Flicking allows you to navigate through screens or quickly scroll through documents. ● Place three fingers on the TouchPad zone and flick your fingers in a light, quick motion up, down, left or right. Edge swipes (select models only) Edge swipes allow you to access toolbars on your computer for tasks such as changing settings and finding or using apps.
Left-edge swipe The left-edge swipe accesses your recently opened apps so that you can switch between them quickly. Swipe your finger gently from the left edge of the TouchPad to switch between recently opened apps. ● Swipe from the left edge of the TouchPad to switch between apps. Top-edge swipe The top-edge swipe displays app command options that allow you to customize apps. IMPORTANT: ● ENWW When an app is open, the top-edge gesture varies depending on the app.
Using the keyboard The keyboard and mouse allow you to type select items, scroll and to perform the same functions as using touch gestures. The keyboard also allows you to use action keys and hot keys to perform specific functions. TIP: The Windows key on the keyboard allows you to quickly return to the Start screen from an open app or the Windows desktop. Pressing the Windows key again will return you to the previous screen.
Hot key combination fn+f4 Description Switches the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, repeatedly pressing fn+f4 alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor. Most external monitors receive video information on the computer using the external VGA video standard.
Using keypads The computer includes an embedded numeric keypad, and it also supports an optional external numeric keypad, or an optional external keyboard that includes a numeric keypad. Using the embedded numeric keypad (1) Component Description fn key Turns the embedded numeric keypad on and off when pressed in combination with the num lock key. NOTE: The embedded numeric keypad will not function while an external keyboard or numeric keypad is connected to the computer.
Turning the embedded numeric keypad on and off Press fn+num lock to turn on the embedded numeric keypad. Press fn+num lock again to turn off the keypad. NOTE: The embedded numeric keypad is turned off while an external keyboard or numeric keypad is connected to the computer.
40 Chapter 4 Navigating using the keyboard, touch gestures and pointing devices ENWW
5 Multimedia Your computer may include the following: ● Integrated speaker(s) ● Integrated microphone(s) ● Integrated webcam ● Preinstalled multimedia software Audio On your computer, or on select models using an external optical drive, you can play music CDs, download and listen to music, stream audio content from the web (including radio), record audio, or mix audio and video to create multimedia. To enhance your listening enjoyment, attach external audio devices such as speakers or headphones.
NOTE: See Getting to know your computer on page 5 for information on what type of volume controls your computer has. Connecting headphones and microphones You can connect wired headphones or headsets to the audio-out (headphone)/audio-in (microphone) jack on your computer. Many headsets with integrated microphones are commercially available. To connect wireless headphones or headsets to your computer, follow the device manufacturer's instructions.
ENWW ● Capturing and sharing video ● Streaming video with instant message software ● Taking still photos Webcam (select models only) 43
Touch to share (select models only) Your computer has advanced Near Field Communication (NFC) hardware that allows you to wirelessly touch-to-share information between two NFC-enabled devices. With NFC technology, you can share websites, transfer contact information, and tap-to-print on NFC supported printers. TIP: You can download NFC apps that may provide additional NFC features. IMPORTANT: Before you can begin sharing, be sure that NFC is enabled on your devices.
● VGA ● DisplayPort IMPORTANT: Be sure that the external device is connected to the correct port on the computer, using the correct cable. Check the device manufacturer's instructions if you have questions. NOTE: ports. See Getting to know your computer on page 5 for information about your computer's video VGA The external monitor port, or VGA port, is an analog display interface that connects an external VGA display device such as an external VGA monitor or a VGA projector to the computer. 1.
DisplayPort The DisplayPort connects the computer to an optional video or audio device, such as a high-definition television, or to any compatible digital or audio component. The DisplayPort delivers higher performance than the VGA external monitor port and improves digital connectivity. NOTE: To transmit video and/or audio signals through the DisplayPort, you need a DisplayPort cable (purchased separately). NOTE: One DisplayPort device can be connected to the DisplayPort port on the computer.
Discovering and connecting wired displays using MultiStream Transport MultiStream Transport (MST) allows you to connect multiple wired displays to your computer. You can connect in several ways, depending on the type of graphics controller installed on your computer and whether or not your computer includes a built-in hub. Go to Device Manager to find out what hardware is installed on your computer. 1. From the Start screen, type control panel, and then select Control Panel. 2.
Connect displays to computers with Intel graphics (with a built-in hub) With your internal hub and Intel graphics controller, you can connect up to 3 display devices in the following configurations: ● Two 1920 x 1200 DP monitors + one 1920 x 1200 VGA monitor connected to an optional docking station ● One 2560 x 1600 DP monitor + one 1920 x 1200 VGA monitor connected to an optional docking station To set up multiple displays, follow these steps: 1.
6 Power management NOTE: A computer may have a power button or a power switch. The term power button is used throughout this guide to mean both types of power controls. Shutting down (turning off) the computer CAUTION: Unsaved information is lost when the computer shuts down. The shutdown command closes all open programs, including the operating system, and then turns off the display and computer.
● Disconnect the computer from external power. ● On models with a user-replaceable battery, remove the battery. On models with a factory-sealed battery, press and hold the power button for at least 15 seconds. Setting power options Using power-saving states Sleep is enabled at the factory. When Sleep is initiated, the power lights blink and the screen clears. Your work is saved to memory.
Enabling and exiting user-initiated Hibernation You can enable user-initiated Hibernation and change other power settings and timeouts using Power Options: 1. From the Start screen, type power options, and then select Power Options. 2. In the left pane, click Choose what the power button does. 3. Click Change Settings that are currently unavailable. 4. In the When I press the power button area, select Hibernate. 5. Click Save changes. To exit Hibernation, briefly press the power button.
Using battery power WARNING! To reduce potential safety issues, use only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased from HP. The computer runs on battery power whenever it is not plugged into external AC power. Computer battery life varies, depending on power management settings, running programs, display brightness, external devices connected to the computer, and other factors.
Using Battery Check HP Support Assistant provides information on the status of the battery installed in the computer. To run Battery Check: 1. Connect the AC adapter to the computer. NOTE: 2. The computer must be connected to external power for Battery Check to work properly. To access battery information, select the HP Support Assistant app on the Start screen, and then select Battery and performance.
If the computer is on or in the Sleep state, the computer remains briefly in the Sleep state, and then shuts down and loses any unsaved information.
3. Insert the battery (1) into the battery bay at an angle and then press down on the battery (2) until it is fully seated. The battery release latch (3) automatically locks the battery into place. Removing a battery To remove the battery: CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and shut down the computer through Windows before removing the battery. ENWW 1.
4. Remove the battery from the computer (3). Conserving battery power ● From the Start screen, type power, select Settings, and then select Power Options. ● Select low power-use settings through Power Options. ● Turn off wireless and LAN connections and exit modem applications when you are not using them. ● Disconnect unused external devices that are not plugged into an external power source. ● Stop, disable, or remove any external memory cards that you are not using.
Calibrate a battery before using it if it has been stored for one month or more. Disposing of a user-replaceable battery (select models only) WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water. See the Regulatory, Safety and Environmental Notices for proper battery disposal. To access this guide, from the Start screen, type support, and then select the HP Support Assistant app.
Testing an AC adapter Test the AC adapter if the computer exhibits any of the following symptoms when it is connected to AC power: ● The computer does not turn on. ● The display does not turn on. ● The power lights are off. To test the AC adapter: NOTE: The following instructions apply to computers with user-replaceable batteries. 1. Shut down the computer. 2. Remove the battery on the computer. 3. Connect the AC adapter to the computer, and then plug it into an AC outlet. 4.
7 External cards and devices Using memory card readers Optional memory cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other computers. Inserting a memory card CAUTION: To reduce the risk of damage to the memory card connectors, use minimal force to insert a memory card. 1. Hold the card label-side up, with the connectors facing the computer. 2.
Removing a memory card CAUTION: To reduce the risk of loss of data or an unresponsive system, use the following procedure to safely remove the memory card. 1. Save your information and close all programs associated with the memory card. 2. Click the remove hardware icon on the Windows desktop in the notification area, at the far right of the taskbar. Then follow the on-screen instructions. 3. Pull the card out of the slot. Using smart cards NOTE: Cards.
Inserting a smart card 1. Hold the card label-side up, and gently slide the card into the smart card reader until the card is seated. 2. Follow the on-screen instructions for logging on to the computer using the smart card PIN. Removing a smart card ▲ Grasp the edge of the smart card, and then pull it out of the smart card reader.
Connecting a USB device CAUTION: device. ▲ To reduce the risk of damage to a USB connector, use minimal force to connect the Connect the USB cable for the device to the USB port. NOTE: The following illustration may look slightly different than your computer. You will hear a sound when the device has been detected. NOTE: The first time you connect a USB device, a message in the notification area lets you know that the device is recognized by the computer.
1. Connect the device to the computer. 2. If you are connecting a powered device, plug the device power cord into a grounded AC outlet. 3. Turn on the device. To disconnect an unpowered external device, turn off the device, and then disconnect it from the computer. To disconnect a powered external device, turn off the device, disconnect it from the computer, and then unplug the AC power cord.
64 Chapter 7 External cards and devices ENWW
8 Drives Handling drives CAUTION: Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply. Observe these precautions: ENWW ● Before you move a computer that is connected to an external hard drive, initiate Sleep and allow the screen to clear, or properly disconnect the external hard drive.
Using hard drives CAUTION: To prevent information loss or an unresponsive system: ● Save your work and shut down the computer before adding or replacing a memory module or hard drive. ● If you are not sure whether the computer is off, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
2. Slide the service door toward the front of the computer (4) and lift (5) to remove the service door. Replacing the service door Replace the service door after accessing the memory module slot, hard drive, regulatory label, and other components. ENWW 1. Tilt down the service door to align the front edge of the service door near the front edge of the computer (1). 2. Insert the alignment tabs (2) on the rear edge of the service door with the notches on the computer. 3.
4. With the service door release latch toward you, slide the service door release latch (3) to the right, and if you choose to, insert and tighten the optional screw (4) to hold the service door in place. Slide the release latch to the left to lock the service door (5). NOTE: If you do not want to use the optional screw, it is stored inside the service door.
6. Loosen the 4 hard drive screws (1). Pull the hard drive tab (2) to disconnect the hard drive. 7. Lift the hard drive (3) out of the hard drive bay. Installing a hard drive NOTE: Your computer may look slightly different from the illustration in this section. To install the hard drive: ENWW 1. Insert the hard drive into the hard drive bay at an angle (1). 2. Pull the plastic tab (2) toward the edge of the computer to engage the hard drive with the connector.
3. Tighten the hard drive screws (3). 4. Insert the battery (see Inserting a battery on page 54). 5. Replace the service door (see Replacing the service door on page 67). 6. Connect AC power and external devices to the computer. 7. Turn on the computer. Improving hard drive performance Using Disk Defragmenter As you use the computer, files on the hard drive become fragmented.
1. Connect the computer to AC power. 2. From the Start screen, type disk. 3. Click Optimize. NOTE: Windows includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to HP Support Assistant. To access HP Support Assistant, from the Start screen, select the HP Support Assistant app.
72 Chapter 8 Drives ENWW
9 Security Protecting the computer Standard security features provided by the Windows operating system and the non-Windows Computer Setup utility (BIOS) can protect your personal settings and data from a variety of risks. NOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. NOTE: Before you send your computer for service, back up and delete confidential files, and remove all password settings.
Using passwords A password is a group of characters that you choose to secure your computer information. Several types of passwords can be set, depending on how you want to control access to your information. Passwords can be set in Windows or in the non-Windows Computer Setup utility that is preinstalled on the computer. ● BIOS administrator and DriveLock passwords are set in Computer Setup and are managed by the system BIOS. ● Automatic DriveLock passwords are enabled in Computer Setup.
Setting passwords in Computer Setup Password Function BIOS administrator password* Protects access to Computer Setup. NOTE: If features have been enabled to prevent removing the BIOS administrator password, you may not be able to remove it until those features have been disabled. DriveLock master password* Protects access to the internal hard drive that is protected by DriveLock. It is also used to remove DriveLock protection. This password is set under DriveLock Passwords during the enable process.
3. Use a pointing device or the arrow keys to select Security > Change Password, and then press enter. 4. When prompted, type your current password. 5. When prompted, type your new password again to confirm. 6. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts.
drive, a password must be entered to access the drive. The drive must be inserted into the computer or an advanced port replicator in order for it to be accessed by the DriveLock passwords. NOTE: A BIOS Administrator password must be set before you can access the DriveLock features. To apply DriveLock protection to an internal hard drive, a user password and a master password must be set in Computer Setup.
Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Entering a DriveLock password Be sure that the hard drive is inserted into the computer (not into an optional docking device or external MultiBay). At the DriveLock Password prompt, type your user or master password (using the same kind of keys you used to set the password), and then press enter.
4. Enter the BIOS Administrator password, and then press enter. 5. Use a pointing device or the arrow keys to select Set DriveLock Password, and then press enter. 6. Use a pointing device or the arrow keys to select an internal hard drive, and then press enter. 7. Use a pointing device or the arrow keys to select Disable protection. 8. Type your master password, and then press enter. 9. To save your changes and exit Computer Setup, click the Save icon and then follow the onscreen instructions.
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Use a pointing device or the arrow keys to select Security > Hard Drive Tools > Automatic DriveLock, and then press enter. 4. Enter the BIOS Administrator password, and then press enter. 5. Use a pointing device or the arrow keys to select an internal hard drive, and then press enter. 6.
NOTE: Under some circumstances a firewall can block access to Internet games, interfere with printer or file sharing on a network, or block authorized e-mail attachments. To temporarily resolve the problem, disable the firewall, perform the task that you want to perform, and then reenable the firewall. To permanently resolve the problem, reconfigure the firewall. Installing critical security updates CAUTION: Microsoft® sends out alerts regarding critical updates.
Using the fingerprint reader (select models only) Integrated fingerprint readers are available on select computer models. In order to use the fingerprint reader, you must enroll your fingerprints in the HP Client Security's Credential Manager. Refer to the HP Client Security software Help. After you enroll your fingerprints in Credential Manager, you can use HP Client Security's Password Manager to store and fill in your user names and passwords in supported websites and applications.
10 Maintenance Adding or replacing memory modules The computer has one memory module compartment. The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot. NOTE: Before adding or replacing a memory module, make sure the computer has the most recent BIOS version, and update the BIOS if needed. See Updating the BIOS on page 95.
a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up. b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 6.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 7. Replace the service door (see Replacing the service door on page 67). 8. Insert the battery (see Inserting a battery on page 54). 9. Connect AC power and external devices to the computer. 10. Turn on the computer.
CAUTION: Avoid strong cleaning solvents that can permanently damage your computer. If you are not sure that a cleaning product is safe for your computer, check the product contents to make sure that ingredients such as alcohol, acetone, ammonium chloride, methylene chloride, and hydrocarbons are not included in the product. Fibrous materials, such as paper towels, can scratch the computer. Over time, dirt particles and cleaning agents can get trapped in the scratches.
Updating programs and drivers HP recommends that you update your programs and drivers on a regular basis with the latest versions. Go to http://www.hp.com/support to download the latest versions. You can also register to receive automatic update notifications when they become available. Using SoftPaq Download Manager HP SoftPaq Download Manager (SDM) is a tool that provides quick access to SoftPaq information for HP business computers without requiring the SoftPaq number.
88 Chapter 10 Maintenance ENWW
11 Backup and recovery To protect your information, use Windows backup and restore utilities to back up individual files and folders, back up your entire hard drive, create system repair media (select models only) by using the installed optical drive (select models only) or an optional external optical drive, or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
NOTE: If you are unable to boot (start up) your computer and you cannot use the system repair media you previously created (select models only), you must purchase Windows operating system media to reboot the computer and repair the operating system. For additional information, see Using Windows operating system media (purchased separately) on page 91. Using the Windows recovery tools To recover information you previously backed up, see Windows Help and Support for steps on restoring files and folders.
1. If possible, back up all personal files. 2. If possible, check for the presence of the Recovery Image partition: From the Start screen, type pc, and then select This PC. NOTE: If the Recovery Image partition is not listed, you must recover your operating system and programs using the Windows operating system media and the Driver Recovery media (both purchased separately). For additional information, see Using Windows operating system media (purchased separately) on page 91. 3.
Using Windows Refresh or Windows Reset When your computer is not working properly and you need to regain system stability, the Windows Refresh option allows you to start fresh and keep what is important to you. The Windows Reset option allows you to perform detailed reformatting of your computer, or remove personal information before you give away or recycle your computer. For more information on these features, see Windows Help and Support.
12 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
● To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or use a pointing device to click the item. ● To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the screen, or use the up arrow key or the down arrow key on the keyboard. ● To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow the on-screen instructions.
Updating the BIOS Updated versions of the BIOS may be available on the HP website. Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file.
NOTE: If you connect your computer to a network, consult the network administrator before installing any software updates, especially system BIOS updates. BIOS installation procedures vary. Follow any instructions that are revealed on the screen after the download is complete. If no instructions are revealed, follow these steps: 1. From the Start screen, type file, and then select File Explorer. 2. Click your hard drive designation. The hard drive designation is typically Local Disk (C:). 3.
Using MultiBoot About the boot device order As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly.
4. To move the device up in the boot order, use a pointing device to click the up arrow, or press the + key. – or – To move the device down in the boot order, use a pointing device to click the down arrow, or press the - key. 5. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Entering MultiBoot Express preferences When the Express Boot menu is displayed during startup, you have the following choices: ● To specify a boot device from the Express Boot menu, select your preference within the allotted time, and then press enter. ● To prevent the computer from defaulting to the current MultiBoot setting, press any key before the allotted time expires. The computer will not start until you select a boot device and press enter.
1. Go to http://www.hp.com. 2. Point to Support, located at the top of the page, and then click Download Drivers. 3. In the text box, enter the product name, and then click Go. – or – Click Find Now to let HP automatically detect your product. 4. Select your computer model, and then select your operating system. 5. In the Diagnostic section, click HP UEFI Support Environment. – or – Click Download, and then select Run.
13 Support Contacting support If the information provided in this user guide or HP Support Assistant does not address your questions, you can contact support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician. NOTE: ENWW When support chat is not available in a particular language, it is available in English. ● Find support telephone numbers.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: IMPORTANT: All labels described in this section will be located in one of 3 places depending on your computer model: affixed to the bottom of the computer, located in the battery bay, or under the service door. ● Service label—Provides important information to identify your computer.
14 Specifications ENWW ● Input power ● Operating environment 103
Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
Operating environment Factor Metric U.S.
106 Chapter 14 Specifications ENWW
A Traveling with the computer For best results, follow these traveling and shipping tips: ● Prepare the computer for traveling or shipping: ◦ Back up your information. ◦ Remove all discs and all external media cards, such as memory cards. CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information, remove the media from a drive before removing the drive from a drive bay and before shipping, storing, or traveling with a drive.
◦ Check the computer-related customs regulations for each country or region on your itinerary. ◦ Check the power cord and adapter requirements for each location in which you plan to use the computer. Voltage, frequency, and plug configurations vary. WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not attempt to power the computer with a voltage converter kit sold for appliances.
B Troubleshooting Troubleshooting resources ● Access website links and additional information about the computer through HP Support Assistant. To access HP Support Assistant, from the Start screen, select the HP Support Assistant app. NOTE: Some checkup and repair tools require an Internet connection. HP also provides additional tools that do not require an Internet connection. ● Contact HP support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.
The computer screen is blank If the screen is blank but you have not turned off the computer, one or more of these settings may be the cause: ● The computer may be in the Sleep state. To exit Sleep, briefly press the power button. Sleep is an energy-saving feature that turns off the display. Sleep can be initiated by the system while the computer is on but is not in use, or when the computer has reached a low battery level.
An external device is not working Follow these suggestions if an external device does not function as expected: ● Turn on the device according to the manufacturer's instructions. ● Be sure that all device connections are secure. ● Be sure that the device is receiving electrical power. ● Be sure that the device, especially if it is older, is compatible with the operating system. ● Be sure that the correct drivers are installed and updated.
◦ The playback window in the multimedia program may close. To return to playing the disc, click the Play button in your multimedia program to restart the disc. In rare cases, you may need to exit the program and then restart it. A movie is not visible on an external display 1. If both the computer display and an external display are turned on, press fn+f4 one or more times to switch between the 2 displays. 2. Configure the monitor settings to make the external display primary: a.
C Electrostatic discharge Electrostatic discharge is the release of static electricity when two objects come into contact—for example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.
114 Appendix C Electrostatic discharge ENWW
Index Symbols/Numerics 2-finger pinch zoom TouchPad gesture 32 A AC adapter, testing 58 AC adapter/battery light 19 accessory battery connector, identifying 17 administrator password 74 airport security devices 65 antivirus software 80 audio functions, checking 42 audio-in (microphone) jack, identifying 5, 6 audio-out (headphone) jack, identifying 5, 6 Automatic DriveLock password entering 79 removing 79 B battery conserving power 56 discharging 53 displaying remaining charge 53 disposing 57 low battery le
function keys, identifying 16 G GPS 26 H hard drive external 63 HP 3D DriveGuard 71 installing 69 removing 68 hard drive light 19, 71 hard drive recovery 90 hard drive, identifying 17 headphone (audio-out) jack 5, 6 headphones and microphones, connecting 42 Hibernation exiting 51 initiating 51 high-definition devices, connecting 47, 48 hot keys adjusting volume 37 decrease screen brightness 37 decreasing speaker sound 37 description 36 increase screen brightness 37 increasing speaker sound 37 keyboard bac
DriveLock 76 user 74 pointing devices, setting preferences 30 pointing stick 11 ports DisplayPort 5, 6, 46 external monitor 8, 9, 45 Miracast 48 USB 3.
Windows key, identifying 16 Windows operating system DVD 91 wireless antennas, identifying 10 wireless button 21 wireless certification label 102 wireless controls button 21 operating system 21 wireless light 13, 19, 21 wireless network (WLAN) connecting 24 corporate WLAN connection 24 equipment needed 23 functional range 24 public WLAN connection 24 security 23 using 22 WLAN antennas, identifying 10 WLAN device 22, 102 WLAN label 102 writable media 50 WWAN antennas, identifying 10 WWAN device 21, 24 118 I
