User Guide
© Copyright 2014 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel and Centrino are trademarks of Intel Corporation in the U.S. and other countries. AMD is a trademark of Advanced Micro Devices, Inc. Microsoft and Windows are U.S. registered trademarks of the Microsoft group of companies. The information contained herein is subject to change without notice.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome ........................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ......................................................................................................................... 4 Right ..............
4 Navigating using the keyboard, touch gestures and pointing devices ............................................................ 33 Using pointing devices ....................................................................................................................... 33 Setting pointing device preferences ................................................................................... 33 Using the TouchPad and gestures ..............................................................................
Finding additional battery information ............................................................... 46 Using Battery Check ......................................................................................... 46 Displaying the remaining battery charge ........................................................... 47 Maximizing battery discharge time .................................................................... 47 Managing low battery levels ........................................................
Installing a hard drive ........................................................................................ 60 Improving hard drive performance ..................................................................................... 61 Using Disk Defragmenter .................................................................................. 61 Using Disk Cleanup ........................................................................................... 62 Using HP 3D DriveGuard (select models only) ......
11 Backup and recovery .................................................................................................................................... 78 Creating recovery media and backups ............................................................................................... 78 Guidelines .......................................................................................................................... 78 Creating recovery media with HP Recovery Disc Creator ...........................
Appendix B Troubleshooting .............................................................................................................................. 93 Troubleshooting resources ................................................................................................................. 93 Resolving issues ................................................................................................................................ 93 The computer is unable to start up ............................
1 Welcome After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, see Connecting to a network on page 26. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer. For more information, see Using antivirus software on page 70.
Finding information You have already used Setup Instructions to turn on the computer and locate this guide. To locate resources that provide product details, how-to information, and more, use this table. Resources For information about Setup Instructions poster ● How to set up the computer ● Help to identify computer components Help and Support ● Operating system information To access Help and Support, select Start > Help and Support.
Resources For information about When you request a printed copy of your warranty, please include your product number, warranty period (found on your service label), name, and postal address. IMPORTANT: Do NOT return your HP product to the addresses above. For U.S. support, go to http://www.hp.com/go/ contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html.
2 Getting to know your computer Right NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Audio-out (headphone)/Audio-in (microphone) jack Connects optional powered stereo speakers, headphones, earbuds, or a headset. Also connects an optional headset microphone. This jack does not support optional microphone-only devices. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset.
Component (1) Description Audio-out (headphone)/Audio-in (microphone) jack Connects optional powered stereo speakers, headphones, earbuds, or a headset. Also connects an optional headset microphone. This jack does not support optional microphone-only devices. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety, and Environmental Notices.
Component (1) Description Audio-out (headphone)/Audio-in (microphone) jack Connects optional powered stereo speakers, headphones, earbuds, or a headset. Also connects an optional headset microphone. This jack does not support optional microphone-only devices. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety, and Environmental Notices.
Left NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (2) Power connector Connects an AC adapter. (3) AC adapter/Battery light ● White: The computer is connected to external power and the battery is charged from 90 to 99 percent.
Component Description (1) Power connector Connects an AC adapter. (2) AC adapter/Battery light ● White: The computer is connected to external power and the battery is charged from 90 to 99 percent. ● Amber: The computer is connected to external power and the battery is charged from 0 to 89 percent. ● Off: The battery is fully charged. (3) Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.
Component Description (1) Power connector Connects an AC adapter. (2) AC adapter/Battery light ● White: The computer is connected to external power and the battery is charged from 90 to 99 percent. ● Amber: The computer is connected to external power and the battery is charged from 0 to 89 percent. ● Off: The battery is fully charged. (3) Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.
Display NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) WLAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide area networks (WWAN). (3) Internal microphones (2) (select models only) Record sound.
Component Description (1) WLAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide area networks (WWAN). (3) Internal microphones (2) (select models only) Record sound. (4) Webcam light (select models only) On: The webcam is in use. (5) Webcam (select models only) Records video and captures photographs.
Component Description (1) Internal microphones (2) Record sound. (2) Webcam light On: The webcam is in use. (3) Webcam Records video and captures photographs. Some models allow you to video conference and chat online using streaming video. For information on using the webcam, select Start > All Programs > Communication and Chat > HP WebCam. (4) WLAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless local area networks (WLAN).
Top TouchPad Component Description (1) TouchPad on/off button Turns the TouchPad on and off. (2) TouchPad zone Moves the pointer and selects or activates items on the screen. NOTE: The TouchPad also supports edge-swipe gestures. For more information, see Edge swipes (select models only) on page 34. (3) Left TouchPad button Functions like the left button on an external mouse. (4) Right TouchPad button Functions like the right button on an external mouse.
Lights NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state, a powersaving state. The computer shuts off power to the display and other unneeded components. ● Off: The computer is off or in Hibernation. Hibernation is a power-saving state that uses the least amount of power. (2) Caps lock light On: Caps lock is on, which switches the keys to all capital letters.
Component (7) Description TouchPad light Component (1) ● White: Computer sound is on. ● Amber: The TouchPad is off. ● Off: The TouchPad is on. Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state, a powersaving state. The computer shuts off power to the display and other unneeded components. ● Off: The computer is off or in Hibernation. Hibernation is a power-saving state that uses the least amount of power.
Component (6) (7) 16 Description Speaker mute light TouchPad light Chapter 2 Getting to know your computer ● Amber: Computer sound is off. ● White: Computer sound is on. ● Amber: The TouchPad is off. ● Off: The TouchPad is on.
Buttons, speakers, and fingerprint reader (select models only) NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component Description (4) Speaker mute button Mutes and restores speaker sound. (5) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a password logon. Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep.
Component Description (3) Wireless button Turns the wireless feature on or off but does not establish a wireless connection. (4) Speaker mute button Mutes and restores speaker sound. (5) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a password logon.
Keys NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (3) Windows key Displays the Windows Start menu. (4) Function keys Execute frequently used system functions when pressed in combination with the fn key.
Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (3) Windows key Displays the Windows Start menu. (4) Function keys Execute frequently used system functions when pressed in combination with the fn key.
Bottom NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Vents (2) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (2) Service door Provides access to the hard drive bay and the memory module slots. (3) Battery release latch Releases the battery.
Component Description CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact support. To access Help and Support, select Start > Help and Support. (5) Battery bay Holds the battery.
Component Description CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact support. To access Help and Support, select Start > Help and Support.
Front Component (1) Description Hard drive light ● Blinking white: The hard drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. NOTE: For more information about HP 3D DriveGuard, see Using HP 3D DriveGuard (select models only) on page 62. (2) Memory card reader Reads optional memory cards that store, manage, share, or access information.
3 Connecting to a network Your computer can travel with you wherever you go. But even at home, you can explore the globe and access information from millions of websites using your computer and a wired or wireless network connection. This chapter will help you get connected to that world. Connecting to a wireless network Wireless technology transfers data across radio waves instead of wires.
Select Start > All Programs > Productivity and Tools > HP Connection Manager, and then click the power button next to the desired device. Using HP Connection Manager (select models only) HP Connection Manager provides a central location for managing your wireless devices, an interface for connecting to the Internet using HP Mobile Broadband, and an interface for sending and receiving SMS (text) messages.
● A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points that can accommodate a large number of computers and accessories and can separate critical network functions. ● A home or small office WLAN typically uses a wireless router, which allows several wireless and wired computers to share an Internet connection, a printer, and files without requiring additional pieces of hardware or software.
Protecting your WLAN When you set up a WLAN or access an existing WLAN, always enable security features to protect your network from unauthorized access. WLANs in public areas (hotspots) like coffee shops and airports may not provide any security. If you are concerned about the security of your computer in a hotspot, limit your network activities to email that is not confidential and basic Internet surfing.
network service provider (called a mobile network operator), which in most cases is a cellular phone network operator. Coverage for HP Mobile Broadband is similar to cellular phone voice coverage. When used with mobile network operator service, HP Mobile Broadband gives you the freedom to stay connected to the Internet, send email, or connect to your corporate network whether you are on the road or outside the range of Wi-Fi hotspots.
8. Insert the SIM into the SIM slot, and gently push the SIM into the slot until it is firmly seated. NOTE: See the image below to determine which way the SIM should be inserted into your computer. 9. Replace the service doors (see Replacing the service doors on page 58). 10. Insert the battery (see Inserting or removing the battery on page 48). NOTE: HP Mobile Broadband will be disabled if the battery is not replaced. 11. Reconnect external power. 12. Reconnect external devices. 13.
Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network (PAN) of Bluetooth devices. For information about configuring and using Bluetooth devices, see the Bluetooth software Help. Connecting to a wired network Your computer has a local area network (LAN) wired connection. A LAN connection uses a network cable which is sold separately.
4 Navigating using the keyboard, touch gestures and pointing devices Your computer allows navigation using touch gestures (select models only) in addition to the keyboard and mouse. Touch gestures can be used on your computer TouchPad or on a touch screen (select models only). Select computer models have special action key or hot key functions on the keyboard to perform routine tasks.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off button. Tapping To make an on-screen selection, use the Tap function on the TouchPad. ● 34 Tap one finger on the TouchPad zone to make a selection. Double-tap an item to open it.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. ● Place two fingers slightly apart on the TouchPad zone and then drag them up, down, left, or right. 2-finger pinch zoom 2-finger pinch zoom allows you to zoom out or in on images or text. ● Zoom in by placing two fingers together on the TouchPad zone and then moving your fingers apart. ● Zoom out by placing two fingers apart on the TouchPad zone and then moving your fingers together.
Rotating (select models only) Rotating allows you to turn items such as photos. ● Anchor the forefinger of your left hand in the TouchPad zone. Using your right hand, slide your forefinger in a sweeping motion from 12 o’clock to 3 o’clock. To reverse the rotation, move your forefinger from 3 o’clock to 12 o’clock. Flicking (select models only) Flicking allows you to navigate through screens or quickly scroll through documents.
Identifying the hot keys A hot key is a combination of the fn key (1) and either the esc key (2), or one of the function keys (3). To use a hot key: ▲ Briefly press the fn key, and then briefly press the second key of the hot key combination. Hot key combination Description fn+esc Displays system information. fn+f3 Initiates Sleep, which saves your information in system memory. The display and other system components turn off and power is conserved. To exit Sleep, briefly press the power button.
Using the embedded numeric keypad (select models only) (1) Component Description fn key Turns the embedded numeric keypad on and off when pressed in combination with the num lk key. NOTE: The embedded numeric keypad will not function while an external keyboard or numeric keypad is connected to the computer. (2) Embedded numeric keypad When the keypad is turned on, it can be used like an external numeric keypad.
Using the integrated numeric keypad (select models only) (1) Component Description num lk key Alternates between the navigational and numeric functions on the integrated numeric keypad. NOTE: The keypad function that is active when the computer is turned off is reinstated when the computer is turned back on. (2) Integrated numeric keypad When num lk has been enabled, it can be used like an external numeric keypad.
5 Multimedia Your computer may include the following: ● Integrated speaker(s) ● Integrated microphone(s) ● Integrated webcam ● Preinstalled multimedia software ● Multimedia buttons or keys Audio On your HP computer, you can play music CDs, download and listen to music, stream audio content from the web (including radio), record audio, or mix audio and video to create multimedia. To enhance your listening enjoyment, attach external audio devices such as speakers or headphones.
WARNING! To reduce the risk of personal injury, lower the volume setting before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety and Environmental Notices. To access this guide, select Start > Help and Support > User guides. Checking audio functions on the computer NOTE: For best results when recording, speak directly into the microphone and record sound in a setting free of background noise.
IMPORTANT: Be sure that the external device is connected to the correct port on the computer, using the correct cable. Check the device manufacturer's instructions if you have questions. NOTE: ports. See Getting to know your computer on page 4 for information about your computer's video VGA The external monitor port, or VGA port, is an analog display interface that connects an external VGA display device such as an external VGA monitor or a VGA projector to the computer. 1.
To connect a video or audio device to the HDMI port: 1. Connect one end of the HDMI cable to the HDMI port on the computer. 2. Connect the other end of the cable to the video device 3. Press fn+f4 to alternate the computer screen image between 4 display states: ● PC screen only: View the screen image on the computer only. ● Duplicate: View the screen image simultaneously on both the computer and external device. ● Extend: View the screen image extended across both the computer and external device.
6 Power management NOTE: A computer may have a power button or a power switch. The term power button is used throughout this guide to mean both types of power controls. Shutting down the computer CAUTION: Unsaved information is lost when the computer shuts down. The shutdown command closes all open programs, including the operating system, and then turns off the display and computer.
NOTE: You cannot initiate any type of networking connection or perform any computer functions while the computer is in the Sleep state. Initiating and exiting Sleep With the computer on, you can initiate Sleep in any of the following ways: ● Briefly press the power button. ● Close the display. ● Select Start, click the arrow next to the Shut down button, and then click Sleep. To exit Sleep ● Briefly press the power button. ● If the display is closed, open the display.
Setting password protection on wakeup To set the computer to prompt for a password when the computer exits Sleep or Hibernation, follow these steps: 1. Select Start > Control Panel > System and Security > Power Options. 2. In the left pane, click Require a password on wakeup. 3. Click Change Settings that are currently unavailable. 4. Click Require a password (recommended).
1. Connect the AC adapter to the computer. NOTE: The computer must be connected to external power for Battery Check to work properly. 2. Select Start > Help and Support > Troubleshoot > Power, Thermal, and Mechanical. 3. Click the Power tab, and then click Battery Check. Battery Check examines the battery and its cells to see if they are functioning properly, and then reports the results of the examination.
● AC adapter ● Optional USB docking or expansion device ● Optional power adapter purchased as an accessory from HP Resolving a low battery level when no power source is available To resolve a low battery level when no power source is available, save your work and shut down the computer. Inserting or removing the battery NOTE: Refer to the illustration that most closely matches your computer. Inserting a battery (with lock latch) To insert the battery: 1.
3. Tilt the battery upward (3) and remove it from the computer (4). Inserting a battery (without lock latch) To insert the battery: 1. Turn the computer upside down on a flat surface, with the battery bay toward you. 2. Insert the battery into the battery bay, aligning the tabs on the battery (1) with the notches on the computer. 3. Tilt the battery (2) down until it is seated. The battery release latches automatically lock the battery into place.
3. Tilt the battery upward (3) and remove it from the computer (4). Conserving battery power ● Select low power-use settings through Power Options in Windows Control Panel. ● Turn off wireless and LAN connections and exit modem applications when you are not using them. ● Disconnect unused external devices that are not plugged into an external power source. ● Stop, disable, or remove any external memory cards that you are not using. ● Decrease screen brightness.
Replacing a user-replaceable battery Battery Check notifies you to replace the battery when an internal cell is not charging properly or when the battery storage capacity has reached a weak condition. If the battery is possibly covered by an HP warranty, instructions include a warranty ID. A message refers you to the HP website for more information about ordering a replacement battery. Using external AC power WARNING! Do not charge the computer battery while you are onboard aircraft.
3. Connect the AC adapter to the computer, and then plug it into an AC outlet. 4. Turn on the computer. ● If the power lights turn on, the AC adapter is working properly. ● If the power lights remain off, the AC adapter is not functioning and should be replaced. Contact support for information on obtaining a replacement AC power adapter.
Using switchable graphics (select models only) Switchable graphics allow you to switch between Performance mode and Power Saving mode. To manage your switchable graphics settings: 1. Right-click on the Windows desktop, and then select Configure Switchable Graphics. 2. Click the Power tab, and then select Switchable Graphics. Switchable graphics assigns individual applications to either Performance mode or Power Saving mode, based on power requirements.
7 External cards and devices Using memory card readers Optional memory cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other computers. To determine the memory card formats that are supported on your computer, see Getting to know your computer on page 4. Inserting a memory card CAUTION: To reduce the risk of damage to the memory card connectors, use minimal force to insert a memory card. 1.
3. Press in on the card (1), and then remove it from the slot (2). NOTE: If the card does not eject, pull the card out of the slot. Using a USB device Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Some USB devices may require additional support software, which is usually included with the device.
NOTE: The first time you connect a USB device, a message in the notification area lets you know that the device is recognized by the computer. Removing a USB device CAUTION: To reduce the risk of damage to a USB connector, do not pull on the cable to remove the USB device. CAUTION: To reduce the risk of loss of information or an unresponsive system, use the following procedure to safely remove the USB device. 1.
8 Drives Handling drives CAUTION: Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Do not drop a drive, place items on it, or expose it to liquids, or temperature or humidity extremes. Observe these precautions when handling drives: ● Before removing or installing a drive, shut down the computer. If you are unsure whether the computer is off, in the Sleep state, or in Hibernation, turn the computer on, and then shut it down.
1. Remove the battery (see Inserting or removing the battery on page 48). 2. With the battery bay away from you, loosen the service door screw (1). The service door screw secures both service doors. 3. Slide the larger service door away from the battery bay (2) to remove it. 4. Slide the smaller service door away from the battery bay (3) to release it, and then lift the service door (4) to remove it. NOTE: Your computer may look slightly different from the illustration in this section.
4. Tighten the service door screw (4) to secure both service doors. NOTE: Your computer may look slightly different from the illustration in this section. 5. Insert the battery (see Inserting or removing the battery on page 48). Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation.
5. Remove the service doors (see Removing the service doors on page 57). 6. Loosen the 4 hard drive screws (1). 7. Slide the hard drive (2) away from the center of the computer to disengage it from the connector. 8. Pull the plastic tab (3) to remove the hard drive from the bay. Installing a hard drive NOTE: Your computer may look slightly different from the illustration in this section. To install the hard drive: 60 1. Insert the hard drive into the hard drive bay (1). 2.
3. Tighten the 4 hard drive screws (3). 4. Replace the service doors (see Replacing the service doors on page 58). 5. Insert the battery (see Inserting or removing the battery on page 48). 6. Connect AC power and external devices to the computer. 7. Turn on the computer. Improving hard drive performance Using Disk Defragmenter As you use your computer over time, the files on the hard drive become fragmented.
To run Disk Defragmenter: 1. Connect the computer to AC power. 2. Select Start > All Programs > Accessories > System Tools > Disk Defragmenter. 3. Click Defragment disk. NOTE: Windows includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support. To access Help and Support, select Start > Help and Support.
9 Security Protecting the computer Standard security features provided by the Windows operating system and the non-Windows Computer Setup utility (BIOS) can protect your personal settings and data from a variety of risks. NOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. NOTE: Before you send your computer for service, back up and delete confidential files, and remove all password settings.
Passwords can be set in Windows or in the non-Windows Computer Setup utility that is preinstalled on the computer. ● BIOS administrator and DriveLock passwords are set in Computer Setup and are managed by the system BIOS. ● Automatic DriveLock passwords are enabled in Computer Setup. ● Windows passwords are set only in the Windows operating system.
Setting passwords in Computer Setup Password Function BIOS administrator password* Protects access to Computer Setup. NOTE: If features have been enabled to prevent removing the BIOS administrator password, you may not be able to remove it until those features have been disabled. DriveLock master password* Protects access to the internal hard drive that is protected by DriveLock. It is also used to remove DriveLock protection. This password is set under DriveLock Passwords during the enable process.
4. When prompted, type your current password. 5. When prompted, type your new password again to confirm. 6. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Deleting a BIOS administrator password 1.
● After DriveLock protection is applied to a hard drive, the hard drive can be accessed only by entering either the user password or the master password. ● The owner of the user password should be the day-to-day user of the protected hard drive. The owner of the master password may be either a system administrator or the day-to-day user. ● The user password and the master password can be identical.
Entering a DriveLock password Be sure that the hard drive is inserted into the computer (not into an optional USB docking device or external MultiBay). At the DriveLock Password prompt, type your user or master password (using the same kind of keys you used to set the password), and then press enter. After 2 incorrect attempts to enter the password, you must shut down the computer and try again. Changing a DriveLock password To change a DriveLock password in Computer Setup, follow these steps: 1.
8. Type your master password, and then press enter. 9. To save your changes and exit Computer Setup, click the Save icon and then follow the onscreen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Using Computer Setup Automatic DriveLock In a multiple-user environment, you can set an Automatic DriveLock password.
6. Use a pointing device or the arrow keys to select Disable protection. 7. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Using antivirus software When you use the computer to access e-mail, a network, or the Internet, you potentially expose it to computer viruses.
1. Run Windows Update as soon as possible after you set up your computer. 2. Run Windows Update monthly thereafter. 3. Obtain updates to Windows and other Microsoft programs, as they are released, from the Microsoft website and through the updates link in Help and Support. Using HP Client Security (select models only) HP Client Security software is preinstalled on select computer models. This software can be accessed through Windows Control Panel.
● Near the bottom of the TouchPad ● On the right side of the keyboard ● On the upper-right side of the display ● On the left side of the display Depending on your computer model, the reader may be oriented horizontally or vertically. Both orientations require that you swipe your finger perpendicular to the metallic sensor. See Getting to know your computer on page 4 for the location of the fingerprint reader on your computer.
10 Maintenance Adding or replacing memory modules The computer has one memory module compartment. The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot. NOTE: Before adding or replacing a memory module, make sure the computer has the most recent BIOS version, and update the BIOS if needed. See Updating the BIOS on page 84.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 6. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 7. Replace the service doors (see Replacing the service doors on page 58). 8. Insert the battery (see Inserting or removing the battery on page 48). 9. Connect AC power and external devices to the computer. 10. Turn on the computer.
CAUTION: Avoid strong cleaning solvents that can permanently damage your computer. If you are not sure that a cleaning product is safe for your computer, check the product contents to make sure that ingredients such as alcohol, acetone, ammonium chloride, methylene chloride, and hydrocarbons are not included in the product. Fibrous materials, such as paper towels, can scratch the computer. Over time, dirt particles and cleaning agents can get trapped in the scratches.
technology available. For example, older graphics components might not work well with the most recent gaming software. Without the latest driver, you would not be getting the most out of your equipment. Go to http://www.hp.com/support to download the latest versions of HP programs and drivers. In addition, register to receive automatic update notifications when they become available.
11 Backup and recovery Your computer includes HP and Windows tools to help you safeguard your information and retrieve it if you ever need to. These tools will help you return your computer to a proper working state, all with simple steps. This section provides information about the following processes: ● Creating recovery media and backups ● Restoring and recovering your system Creating recovery media and backups Recovery after a system failure is only as good as your most recent backup. 1.
well as select drivers and applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery DVDs: ● Windows 7 operating system DVD—Installs the operating system without additional drivers or applications. ● Driver Recovery DVD—Installs specific drivers and applications only, in the same way that the HP Software Setup utility installs drivers and applications. Creating recovery media NOTE: The Windows 7 operating system DVD can be created only once.
To create a backup using Windows Backup and Restore: NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or create system repair media (select models only).
1. If possible, back up all personal files. 2. If possible, check for the presence of the Windows partition. To check for the Windows partition, select Start > Computer. NOTE: If the Windows partition is not listed, you must recover your operating system and programs using the Windows 7 operating system DVD and the Driver Recovery media. For additional information, see Using Windows 7 operating system media on page 81. 3.
To initiate recovery using a Windows 7 operating system DVD: NOTE: This process takes several minutes. 1. If possible, back up all personal files. 2. Restart the computer, and then insert the Windows 7 operating system DVD into the optical drive before the Windows operating system loads. 3. When prompted, press any keyboard key. 4. Follow the on-screen instructions. 5. Click Next. 6. Select Repair your computer. 7. Follow the on-screen instructions. After the repair is completed: 82 1.
12 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Restoring factory settings in Computer Setup NOTE: Restoring defaults will not change the hard drive mode.
1. Start Computer Setup. 2. Use a pointing device or the arrow keys to select Main > System Information. 3. To exit Computer Setup without saving your changes, click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
Using MultiBoot About the boot device order As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly.
Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Dynamically choosing a boot device using the f9 prompt To dynamically choose a boot device for the current startup sequence, follow these steps: 1. Open the Select Boot Device menu by turning on or restarting the computer, and then pressing esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f9. 3.
of the operating system to isolate hardware failures from issues that may be caused by the operating system or other software components. To start HP PC Hardware Diagnostics UEFI: 1. Turn on or restart the computer, quickly press esc, and then press f2. After pressing f2, the BIOS searches three places for the HP PC Hardware Diagnostics (UEFI) tools in the following order: a.
13 Support Contacting support If the information provided in this user guide or Help and Support does not address your questions, you can contact support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician. NOTE: When support chat is not available in a particular language, it is available in English. ● E-mail support. ● Find support telephone numbers.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer. IMPORTANT: All labels described in this section will be located in one of 3 places depending on your computer model: affixed to the bottom of the computer, located in the battery bay, or under the service door. ● Service label—Provides important information to identify your computer.
14 Specifications ● Input power ● Operating environment Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz.
A Traveling with or shipping your computer If you have to travel with or ship your computer, here are some tips to keep in mind to keep your equipment safe. ● Prepare the computer for traveling or shipping: ◦ Back up your information to an external drive. ◦ Remove all discs and all external media cards, such as memory cards, from the computer. ◦ Turn off and then disconnect all external devices. ◦ Shut down the computer. ● Take along a backup of your information.
B Troubleshooting Troubleshooting resources ● Access website links and additional information about the computer through Help and Support. To access Help and Support, select Start > Help and Support. NOTE: Some checkup and repair tools require an Internet connection. HP also provides additional tools that do not require an Internet connection. ● Contact HP support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html.
change these and other power settings, right-click the Battery icon on the Windows desktop in the notification area, at the far right of the taskbar, and then click Preferences. ● The computer may not be set to display the image on the computer screen. To transfer the image to the computer screen, press fn+f4.
The wireless network connection is not working If a wireless network connection is not working as expected, follow these suggestions: ● To enable or disable a wireless or wired network device, right-click the Network Connection icon on the Windows desktop in the notification area, at the far right of the taskbar. To enable devices, select the check box from the menu option. To disable the device, clear the check box. ● Be sure that the wireless device is turned on.
The process of burning a disc does not begin, or it stops before completion 96 ● Be sure that all other programs are closed. ● Turn off Sleep mode. ● Be sure that you are using the right kind of disc for your drive. ● Be sure that the disc is inserted properly. ● Select a slower write speed and try again. ● If you are copying a disc, save the information on the source disc to your hard drive before trying to burn the contents to a new disc, and then burn from your hard drive.
C Electrostatic discharge Electrostatic discharge is the release of static electricity when two objects come into contact—for example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.
Index Symbols/Numerics 2-finger pinch zoom TouchPad gesture 35 A AC adapter, testing 51 AC adapter/battery light 7, 8, 9 administrator password 64 antivirus software 70 audio functions, checking 41 audio-in (microphone) jack, identifying 4, 5, 6 audio-out (headphone) jack, identifying 4, 5, 6 Automatic DriveLock password entering 69 removing 69 B Backup and Restore 80 backup tools 78 backups creating 79 recovering 80 battery conserving power 50 discharging 47 displaying remaining charge 47 disposing 50 low
hard drive, identifying 22, 23 HDMI port connecting 42 identifying 7, 8, 9 HDMI, configuring audio 43 headphone (audio-out) jack 4, 5, 6 headphones and microphones, connecting 40 Hibernation exiting 45 initiating 45 high-definition devices, connecting 42 hot keys adjusting volume 37 decrease screen brightness 37 decreasing speaker sound 37 description 37 increase screen brightness 37 increasing speaker sound 37 keyboard backlight 37 microphone mute 37 Sleep 37 switching screen image 37 using 37 HP 3D DriveG
HDMI 7, 8, 9, 42 USB 4, 5, 6 VGA 42 power battery 46 conserving 50 options 44 power button identifying 17, 18 managing power 44 power connector, identifying 7, 8, 9 power lights 14, 15 power switch 44 power-saving states 44 product name and number, computer 90 public WLAN connection 29 R readable media 44 recovery media creating 78 using for restore 81 recovery partition 81 recovery tools 78 recovery tools, Windows 80 recovery, system 80 regulatory information regulatory label 90 wireless certification labe
wireless light 14, 15, 26 wireless network (WLAN) connecting 29 corporate WLAN connection 29 equipment needed 28 functional range 29 public WLAN connection 29 security 29 using 27 WLAN antennas, identifying 10, 11, 12 WLAN device 27, 90 WLAN label 90 WLAN, identifying 22, 23 writable media 44 WWAN identifying 22, 23 WWAN antennas, identifying 10, 11 WWAN device 26, 30 Index 101
