OSM User's Guide Next Version and Copyright Information Published February 2006 Table of Contents What's New in This Guide About This Guide Related Reading 1. Introducing OSM OSM Interfaces OSM Service Connection OSM Notification Director OSM Guided Procedures OSM Low-Level Link OSM Event Viewer What Changed From TSM to OSM New Look-and-Feel Functional Differences Between OSM and TSM 2. Preparing the OSM Environment Installing OSM Components System Console-Based Components Server-Based Components 3.
Launching an OSM Service Connection OSM Service Connection Session Error Messages Using OSM Bookmarks Verifying the OSM Service Connection State Running Multiple Sessions 5.
Deleting Alarms 7. Viewing Attributes Using the Details Pane to View Attributes Using the Attributes Dialog Box to View Attributes Suppressing Problem Attributes 8.
Actions ATM Line Attributes Actions Battery Attributes Actions Blower (FCDM) Attributes Actions CCSA (Common Communication ServerNet Adapter) Attributes Actions Disk Attributes Actions Disk (Fibre Channel) Attributes Actions E4SA (Ethernet 4 ServerNet Adapter) Attributes Actions EMU Attributes Actions ESS Disk Attributes Actions ESS Disk Collection Attributes External Disk Attributes Actions
External Disk Collection Attributes Actions Fan Attributes Actions Fan (IOAM) Attributes Actions FC-AL I/O Module Attributes Actions FCDM Attributes Actions FCDM Collection Attributes Actions FCSA Attributes Actions Removing and Installing a Fibre Channel ServerNet Adapter FCSA FSAC Attributes Actions FESA (Fast Ethernet ServerNet Adapter) Attributes Actions FSAC (Fiber ServerNet Addressable Controller) Attributes Actions FXSA / FX2SA (ServerNet/FX / ServerNet/FX2) Attributes
Actions G4SA Attributes Actions G4SA PIF Attributes Actions G4SA SAC Attributes Actions GESA (Gigabyte Ethernet ServerNet Adapter) Attributes Actions Group (I/O or Processor Enclosure) Attributes Actions Group (IOAM) Attributes Actions Internal ServerNet Fabric Attributes Actions IOAM (I/O Adapter Module) Attributes Actions IOAM Enclosure Attributes Actions IOMF (I/O Multifunction) Attributes Actions IOMF2 (I/O Multifunction 2) Attributes
Actions LIF Attributes Actions Maintenance Switch Attributes Actions MIOE (Ethernet Controller) Attributes Actions MIOE PIF Attributes Actions MIOE SAC Attributes Actions Module Attributes Actions Set Physical Location Monitored Service LAN Devices Attributes Actions MSEB Attributes Actions PIC Attributes Actions PIF Attributes Actions PMCU
Attributes Actions PMF (Processor Multifunction) Attributes Actions PMF2 (Processor Multifunction 2) Attributes Actions Power Supply Attributes Actions Replacement Guidelines and Precautions Power Supply (FCDM) Attributes Actions Power Supply (IOAM) Attributes Actions Processor Attributes Actions SAC (ServerNet Addressable Controller) Attributes Actions SCSI Controller Attributes Actions SEB Attributes Actions ServerNet Switch Board Attributes Actions
Service Processor (SP) Attributes Actions SNDA (ServerNet/DA) Attributes Actions SSAC (SCSI SAC) Attributes Actions Storage Router Attributes Actions SWAN / SWAN2 Attributes Actions SWAN Battery Attributes Actions SWAN CLIP Attributes Actions SWAN Collection Attributes Actions SWAN FAN Attributes Actions SWAN LAN Logic Board (LANLB) Attributes Actions SWAN Line Attributes Actions
SWAN Path Attributes Actions SWAN (Power Supply) Attributes Actions System Attributes Actions Tape Collection Attributes Actions Tape Attributes Actions TRSA (Token Ring ServerNet Adapter) Attributes Actions Unknown CRU Attributes Actions UPS Attributes Actions CLIM Collection Attributes Actions CLIM Attributes Actions Common Attribute Values Battery Charge Status Compare State
Device State Enabled State Group Type Path State Power State Processor State Processor Type Service State Tape Types Topology 12.
Attributes Actions Remote 6770 Switch Attributes Actions ServerNet Cluster Attributes Actions ServerNet Local Node Attributes Actions ServerNet Remote Node Attributes Actions ServerNet II Switch Attributes Actions Switch Fan Attributes Actions Switch Group Attributes Actions Switch Logic Board Attributes Actions Switch PIC Attributes Actions Switch Power Supply Attributes Actions Switch-to-Node PIC
Attributes Actions Switch Node Port Attributes Actions Switch-to-Switch PIC Attributes Actions Switch Port Attributes Actions UPS (6770 Switch Module) Attributes Actions Common Attribute Values Service State Fabric State Configuration Tag Port Connectivity Status 14.
Y Fabric Connections for Three Zones Glossary Index Next What's New in This Guide 527274-015 Legal Notices
What's New in This Guide Prev Next What's New in This Guide The OSM Service Connection Suite has been updated to T0682G07 AAL for G06.28. For a complete list of fixes and known problems, see T0682 softdoc. Changes reflected in this help file include: ● Support for connecting HP Ultrium 960 LTO Fibre Channel tape drives (M8501, M8502, M8503, M8504, and M8505) to an S-series system through an FCSA located in an I/O adapter module.
About This Guide Prev Next About This Guide The OSM User's Guide is available as online help within the OSM Service Connection, and in the NonStop Technical Library. From within the OSM Service Connection, you can: ● Get context-sensitive help by selecting a system resource object, action, or OSM management window area and pressing the F1 key. Help is also available from dialog box Help button.
Related Reading Prev Next Related Reading Sources of OSM-related information: ● This manual, the OSM User's Guide, is available in the NonStop Technical Library (NTL) and as online help from within the OSM Service Connection. It deals mostly with using the OSM Service Connection to monitor and perform actions on system and cluster resources. ● The NonStop S-Series Hardware Installation and FastPath Guide describes how to connect and configure a system console for use with OSM software.
Prev About This Guide 527274-015 Up Home Next Chapter 1.
Chapter 1. Introducing OSM Prev Next Chapter 1. Introducing OSM OSM Interfaces OSM Service Connection OSM Notification Director OSM Guided Procedures OSM Low-Level Link OSM Event Viewer What Changed From TSM to OSM New Look-and-Feel Functional Differences Between OSM and TSM The OSM client components are installed on a PC workstation that serves as the system console. The OSM server components are installed on the NonStop server running the HP NonStop operating system.
OSM Interfaces OSM Service Connection OSM Notification Director OSM Guided Procedures OSM Low-Level Link OSM Event Viewer OSM Service Connection The OSM Service Connection is the primary OSM management component. You use the OSM Service Connection to log on and establish a connection with a NonStop server. From the Management window, you can manage the resources of your server. If your server is part of a ServerNet cluster, you can also manage cluster resources.
● Configuration of remote access (dial-in) and remote notification (dial-out) information ● Configuration of dial-out point status for your system console ● Specification of the interval at which your OSM server generates periodic incident reports ● Authorization (automatically or manually) of incident reports to be dialed out to your service provider Note: You can receive and dial out incident reports only from systems for which your system console is a primary or backup dial-out point.
Replace Power Supply Add Switch Replace Upgrade Topology Troubleshoot ServerNet Fabric External Loopback Test Each CRU ServerNet Cluster MSEB and IOMF2 ServerNet plug-in cards (PICs) Firmware Update and Configuration Switch Update Use the Multi-Resource Actions dialog SWAN Fast Firmware Update box to stop, update, and restart any or all SWAN CLIP CLIPs simultaneously.
● Tree pane tabs have been replaced by a view of both the system and the cluster in the tree pane. ● A view pane drop-down list lets you select either a Physical or Inventory view. ● The system-level physical view no longer allows you to change icon sizes. Group icons used in the system-level physical view are smaller than those used by default in TSM, so you can view more groups without scrolling. ● OSM displays object names in the format [Object type] [Object name] ([group.module.slot.port]).
● Attributes are arranged in subgroups under an object, For example, the Fan object has a group of attributes under logical fan and another group under physical fan. Functional Differences Between OSM and TSM To find familiar TSM Service Application functions that have been enhanced or otherwise changed in the OSM Service Connection: This TSM feature... Launching the client, adding systems to your system list, and logging on to a system.
Performing the same TSM action The Multi-Resource Actions dialog box (available from the Display menu) on several objects allows you to initiate an action on any or all resources of the same type of the same type simultaneously. (individually) Rediscover is supported as an action on all system and some cluster objects. For most objects, Rediscover is available only in the shortcut menu. Rediscover menu item Rediscover causes OSM to refresh and reanalyze the object and all subcomponents.
Using Quick-key accelerators (keyboard shortcuts) Prev Related Reading 527274-015 Shortcuts are not supported in OSM because Internet Explorer uses the same keyboard shortcuts for other purposes. Up Home Next Chapter 2.
Chapter 2. Preparing the OSM Environment Prev Next Chapter 2. Preparing the OSM Environment Installing OSM Components System Console-Based Components Server-Based Components To plan your network LAN configuration and connect your system console so it can communicate with your NonStop server through OSM client/server software, see the NonStop S-Series Hardware Installation and FastPath Guide. To migrate from TSM to OSM, see the OSM Migration Guide.
Chapter 1. Introducing OSM 527274-015 Home Chapter 3.
Chapter 3. Configuring OSM Prev Next Chapter 3. Configuring OSM Configuring the Server Defining Users Configuring Service Provider Access Dial-out/Dial-in Unattended Site Before using OSM applications to manage your system: ● Configure the server using the OSM Low-Level Link. ● Configure service provider access using the OSM Notification Director. ● Configure the OSM Notification Director during OSM installation to run as a Windows Service, which allows it to run without requiring a Windows logon.
Use this dialog box To Network Configure unique MSP IP addresses for your primary and backup LANs. Define the workstations authorized to display the startup TACL prompt Startup Windows and receive the event messages that occur during a system load. Define the users that are authorized to connect to the master service processors (MSPs) or maintenance entities (MEs) on your server.
1. Define the general actions each person or group of persons will perform using the OSM software package. 2. Using the OSM Low-Level Link, define the MSP user names and passwords you will use. For more information about defining user names and passwords, see the OSM Low-Level Link online help.
application. This means you can configure it to automatically start upon Windows startup, without requiring a user logon. Unlike the TSM Notification Director, the OSM Notification Director receives and processes incident reports without having to leave the system console logged onto by a super-group user. When you configured TSM as an unattended site during TSM client installation, the installer would configure your PC to automatically log on to Windows when the PC restarted.
Chapter 4. Starting the OSM Service Connection Prev Next Chapter 4. Starting the OSM Service Connection Launching an OSM Service Connection OSM Service Connection Session Error Messages Using OSM Bookmarks Verifying the OSM Service Connection State Running Multiple Sessions You can: ● Launch an OSM Service Connection ● OSM Service Connection Session Error Messages ● Using OSM Bookmarks ● Verify the OSM Service Connection State ● Run Multiple Sessions Launching an OSM Service Connection 1.
a. From the Start menu, select: Start>Programs>HP OSM>OSM Service Connection b. In the left column of the home page, select a bookmark for the system you want to access. 2. The first time you try to establish a service connection you are prompted Click here to download Java Runtime Environment. Select Open and install it according to the instructions. Then close the current browser, open a new browser, and repeat Step 1.
Viewer) automatically converts the TSM system list to bookmarks for accessing the systems through OSM (provided those systems are now running OSM server software). The two bookmarks displayed per system represent the two IP addresses configured by default for fault-tolerant service connections. For details on migrating an existing TSM system list to a new system console (with or without TSM installed), see the OSM Migration Guide.
527274-015 Legal Notices
Chapter 5. Using the Management Window Prev Next Chapter 5.
Displays a high-level view of system objects, such as internal fabrics, groups, and Overview external devices (external disks and tapes), and of ServerNet Cluster objects, such as external fabrics, local nodes, and remote nodes. Tree Displays both system and cluster resources at the same time. Allows you to choose a view of the cluster or system: View ● Select Physical from the view drop-down list to display a physical view. ● Select Inventory from the view drop-down list to display an inventory view.
Management Window Example Internet Explorer Menu Bar The Internet Explorer menu bar is not customized for the OSM application. For most OSM functions, use the OSM toolbar (located just above the view pane) and the various panes within the Management window. Internet Explorer functions that you might use for OSM include ● Access OSM bookmarks from the Internet Explorer Favorites menu. However, you must use the OSM Create Bookmark function in the Tools menu to create the bookmarks.
● Use Find to search the contents of the Inventory view. Internet Explorer features you should not use during an OSM Service Connection session: ● The Go To, Stop, or Refresh options from the View menu. For updating OSM attributes and alarms, use the OSM Rediscover action, available by right-clicking on system resource objects. ● You cannot use Internet Explorer's Add to Favorites menu option to create OSM bookmarks. For this functionality, see Using OSM Bookmarks.
Displays the Multi-Resource Actions dialog box, which enables Multi-Resource Actions... you to perform actions across multiple resources of the same type. See Performing Actions on Multiple Resources of The Same Type. Summary Menu The Summary menu contains the following items: Displays the Problem Summary dialog box, which lists all resources that have some type of problem. Displays the Action Status Summary dialog box, which lists all actions in Action progress.
Displays the Save Snapshot dialog box, which enables you to create and save a snapshot of your system. A snapshot provides information regarding the state of your system and all components at the time that the snapshot file was saved. Save Snapshot You can load and view a saved snapshot on any server running OSM server software. To load a snapshot, launch Internet Explorer and enter the URL of the system you are using to view the snapshot, followed by /snapshot/index.html. For example: http://star2.
Rediscover Shortcut Menu Item Rediscover is supported as an action on all system and some cluster objects. For most objects, Rediscover is available only in the shortcut menu. Rediscover causes OSM to refresh and reanalyze the object and all subcomponents. Refresh refers to OSM updating the attribute values displayed in the OSM Service Connection interface. Reanalyze refers to the running of OSM incident analysis, which checks EMS event messages and creates alarms in OSM if certain conditions exist.
2. From the View drop-down list, select Physical. Physical View of a Local System The Physical view of a local system provides a high-level view of the system configuration and status, showing all groups and external devices such as external disks and SWAN CRUs. The name of the system to which you are connected appears at the top of the view pane. For more detail on items represented in the Physical view of a system, see the Physical view of an enclosure, the Inventory view, or the details pane.
a local system. You can select a resource in the Inventory view and display its attributes or alarms (if any) or perform actions on it. If an alarm is outstanding for the selected resource, a bell icon appears on the Alarms tab in the details pane when you select the resource. For more information, see Viewing the Alarms Dialog Box. To find a resource in this view, use the browser's Find function. For more information, see Using the Browser's Find Feature. To display the Inventory view: 1.
The selected resource and other resources in the corresponding group. An individual resource Components that contain the resource, such as the system, do not appear. An external disk All external disks in the server. Each row lists one component, with adjacent columns listing the following information about each component: The logical name of a component in the system and the slot in which it is Name located. For instance, DISK $DATA (1.2.7) is the name of a disk in Group 1, Module 2, Slot 7.
The only cluster resources that have the Rediscover action are the ServerNet Cluster and External ServerNet Fabric. Interpreting Icons and Color State Indicators Alarm Indicators Alarm Severity The OSM Service Connection uses different icons and colors to indicate a change from normal status in a group or resource in the Management window. The states are indicated as green (normal), yellow (warning), and red (critical). See Alarm Severity.
In the tree pane, a yellow icon displayed over a system, group, module, or any parent object that contains subcomponents indicates that one or more subcomponents require service or operational intervention. State icons are also shown in the Physical view of a cluster or system.
In the Alarm Summary Alarm Severity Immediate corrective action is required. A service-affecting fault occurred. For example, a resource might have become unavailable. Urgent corrective action is required. A service-affecting fault has Major developed. For example, a resource might have lost fault tolerance. A fault exists that does not affect service. Corrective action should be taken to Minor prevent a more serious fault. For example, an unexpected path change occurred.
5. Click Find Next. If a resource with a matching value is found, the matching text is selected in the Inventory view. 6. Click the matching text to select the resource. Information about the resource appears in the details pane. If no resources contain the specified value, a message informs you that the search text was not found. To search for the next occurrence of the specified value, click Find Next.
Chapter 6. Viewing Alarms Prev Next Chapter 6. Viewing Alarms Viewing the Alarms Tab Viewing the Alarms Dialog Box Viewing Alarm Details Suppressing Alarms Deleting Alarms When certain problem conditions exist on a system, OSM generates alarms on the objects in need of service or attention. Alarms can be viewed in these ways: ● ● Alarms associated with a specific resource: ❍ Right-click on the object and choose Alarms to display the Alarms dialog box.
The Severity column contains a colored icon corresponding to the severity of the alarm. Red icons represent Critical and Major alarms. Yellow icons represent Minor, Warning, and Indeterminate alarms. See Alarm Severity. ● Time and date the alarm occurred ● Description of the alarm, including the probable cause ● Whether the alarm is dialed out to your service provider (assuming your system console is configured to dial out). To view alarms in the Alarms tab: 1.
● Time and date the alarm occurred ● Description of the alarm, including the probable cause ● The type of alarm ● Whether the alarm is dialed out to your service provider (assuming your system console is configured to dial out) You can also view alarms for a selected resource without opening the Alarms dialog box as explained in Viewing the Alarms Tab. To display detailed information for an alarm: Highlight the alarm and then click Detail. See also Viewing Alarm Details.
Suppressing Alarms To stop known problems from propagating up and causing higher level object icons to indicate problem conditions within, you can choose to suppress a particular alarm. To suppress an alarm: Right-click an alarm in either the Alarms tab, Alarms dialog box, or the Alarm Summary dialog box and select Suppress. (In the Alarms dialog box or the Alarm Summary dialog box, you can also highlight the alarm and click the Suppress button.). To undo the alarm suppression, select Unsuppress.
Chapter 7. Viewing Attributes Prev Next Chapter 7. Viewing Attributes Using the Details Pane to View Attributes Using the Attributes Dialog Box to View Attributes Suppressing Problem Attributes Every resource has attributes associated with it. You can view the attributes of a resource in the details pane of the Management window, or you can display the Attributes dialog box, which is available from any view.
To show actions for a resource: Click Show Actions to display the Actions dialog box for the resource. To save the list of attributes: Click Save to display a Save dialog box. To reach the attributes dialog box: Do one of: ● In the tree view, select a resource and select Display>Attributes. ● Right-click any resource and select Attributes from the menu that appears. ● In the physical view, right-click a resource and select Attributes from the menu that appears.
Chapter 8. Performing Actions Prev Next Chapter 8.
Performing Actions on a Selected Resource Performing an Action Viewing Detailed Information About an Action Use the Actions dialog box to perform actions on a selected resource in the server or ServerNet cluster. Actions for the selected resource appear in the Available Actions list. For a description of a particular action, highlight the action and press the F1 key. A history of actions performed on the resources within the last eight hours appears in the Action Status list.
Saving a Multi-Resource View Using Customized Resource Views Use the Multi-Resource Actions dialog box to perform an action on a group of resources of the same type. The dialog box allows you to select the resource type. All resources of that type appear in an available resources list, and actions for the selected resource type appear in the Action drop-down menu. You can select an action and then select specific resources on which to perform the action.
Move a specific resource (selected by clicking it) from the available list to the selected list. Remove all Move all resources from the selected list back to the available list. Move a specific resource (selected by clicking it) from the selected list back Remove to the available list. Add 5. Click Perform Action. As the action is performed, its status appears to the left of the resource name in the selected resources list. A summary of the action progress is shown in the Progress status boxes. 6.
dialog box, you can also select a previously-saved resource view from the Configuration list.) 2. The Multi-Resource Actions dialog box is displayed; only those resources specified in the saved resource view appear under Resource Types. Deleting a Resource View 1. In the Multi-Resource Actions dialog box, click Configure&. 2. In the Multi-Resource Configuration dialog box, select the name of the resource view you want to delete from the drop-down menu. 3. Click Delete.
3. From the Action drop-down menu, select the action to perform. A second resources list is displayed below the first: ● You can resize the panes by using the divider line above the add and remove buttons. ● You can sort either resources list by clicking the bottom line of the column heading. 4. To further refine the resources on which to perform the firmware update, select a parameter from the Filter by drop-down list.
Chapter 7. Viewing Attributes 527274-015 Home Chapter 9.
Chapter 9. Viewing Summary Reports Prev Next Chapter 9. Viewing Summary Reports Viewing a Problem Summary Viewing a Summary of Actions Actions Not Displayed OSM Software-Triggered Actions Viewing Action Details Viewing a Summary of Alarms Viewing a Resource Summary You can view a: ● Problem Summary ● Summary of Actions ● Summary of Alarms ● Resource Summary Viewing a Problem Summary The Problem Summary lists all resources that are in a problem state.
Viewing a Summary of Actions Actions Not Displayed OSM Software-Triggered Actions Viewing Action Details The Action Status Summary displays a summary of all actions in progress and actions that have taken place in past 24 hours. Information for each action includes resource name, action name, action status, and progress of the action. You can also view detailed information about each action. Actions Not Displayed The Rediscover action is not reported in the Action Summary dialog box.
alarms for a single resource, as described in Viewing the Alarms Dialog Box. The Alarm Summary dialog box provides this information about each alarm: ● Alarm severity ● Time and date the alarm occurred ● Resource name ● Description of the alarm, including probable cause and alarm type ● Whether the alarm is dialed out to your service provider (assuming your system console is configured to dial out) To display detailed information for an alarm: Highlight the alarm and click Detail.
3. To perform an action on any of the resources, see Performing Actions on Multiple Resources of the Same Type. Prev Chapter 8. Performing Actions 527274-015 Up Home Next Chapter 10.
Chapter 10. Managing a System Prev Next Chapter 10. Managing a System Locating and Viewing System Resources Monitoring a System Performing Actions on a System Updating Firmware A system consists of all the hardware components, software, and firmware that are managed by a single operating system. Using the OSM applications, you can monitor and maintain your local server to check the status of all system components and to watch for indications of potential system problems.
● Checking for incident reports in the OSM Notification Director. The OSM Notification Director generates problem incident reports when critical changes occur to a resource on the system. ● Checking the OSM Event Viewer for events. The OSM Event Viewer displays events from EMS-formatted log files such as $0 and $ZLOG. ● Checking the internal X and Y fabrics to examine the systems connections between its groups.
Chapter 11. System Resources Prev Next Chapter 11.
Actions ESS Disk Collection Attributes External Disk Attributes Actions External Disk Collection Attributes Actions Fan Attributes Actions Fan (IOAM) Attributes Actions FC-AL I/O Module Attributes Actions FCDM Attributes Actions FCDM Collection Attributes Actions FCSA Attributes Actions Removing and Installing a Fibre Channel ServerNet Adapter FCSA FSAC Attributes Actions FESA (Fast Ethernet ServerNet Adapter) Attributes Actions
FSAC (Fiber ServerNet Addressable Controller) Attributes Actions FXSA / FX2SA (ServerNet/FX / ServerNet/FX2) Attributes Actions G4SA Attributes Actions G4SA PIF Attributes Actions G4SA SAC Attributes Actions GESA (Gigabyte Ethernet ServerNet Adapter) Attributes Actions Group (I/O or Processor Enclosure) Attributes Actions Group (IOAM) Attributes Actions Internal ServerNet Fabric Attributes Actions IOAM (I/O Adapter Module) Attributes Actions IOAM Enclosure Attributes Actions IOMF (I/O Multifunction)
Attributes Actions IOMF2 (I/O Multifunction 2) Attributes Actions LIF Attributes Actions Maintenance Switch Attributes Actions MIOE (Ethernet Controller) Attributes Actions MIOE PIF Attributes Actions MIOE SAC Attributes Actions Module Attributes Actions Set Physical Location Monitored Service LAN Devices Attributes Actions MSEB Attributes Actions PIC Attributes Actions PIF
Attributes Actions PMCU Attributes Actions PMF (Processor Multifunction) Attributes Actions PMF2 (Processor Multifunction 2) Attributes Actions Power Supply Attributes Actions Replacement Guidelines and Precautions Power Supply (FCDM) Attributes Actions Power Supply (IOAM) Attributes Actions Processor Attributes Actions SAC (ServerNet Addressable Controller) Attributes Actions SCSI Controller Attributes Actions SEB Attributes Actions ServerNet Switch Board
Attributes Actions Service Processor (SP) Attributes Actions SNDA (ServerNet/DA) Attributes Actions SSAC (SCSI SAC) Attributes Actions Storage Router Attributes Actions SWAN / SWAN2 Attributes Actions SWAN Battery Attributes Actions SWAN CLIP Attributes Actions SWAN Collection Attributes Actions SWAN FAN Attributes Actions SWAN LAN Logic Board (LANLB) Attributes Actions SWAN Line Attributes
Actions SWAN Path Attributes Actions SWAN (Power Supply) Attributes Actions System Attributes Actions Tape Collection Attributes Actions Tape Attributes Actions TRSA (Token Ring ServerNet Adapter) Attributes Actions Unknown CRU Attributes Actions UPS Attributes Actions CLIM Collection Attributes Actions CLIM Attributes Actions Common Attribute Values Battery Charge Status Compare State
Device State Enabled State Group Type Path State Power State Processor State Processor Type Service State Tape Types Topology Using OSM, you can monitor and maintain these system resources: ATM Adapter ATM Line Battery Blower (FCDM) G4SA G4SA PIF G4SA SAC Group (I/O or Processor Enclosure) Processor SAC SCSI Controller SEB CCSA Group (IOAM) ServerNet Switch Board CLIM CLIM Collection Internal ServerNet Fabric IOAM SSAC SNDA Disk Disk (Fibre Channel) IOAM Enclosure IOMF Service Processor Storage R
FXSA / FX2SA GESA Power Supply (FCDM) IOAM Power Supply (IOAM) ATM3SA (ATM Adapter) Attributes Actions A customer-replaceable unit (CRU) that connects the ServerNet SAN inside a server to an Asynchronous Transfer Mode (ATM) network through a logical connection known as an ATM line. Each ATM CRU contains one ATM line. Slot Location: ATM CRUs can be located in slots 53 and 54 in processor enclosures (service side) or in slots 51, 52, 53, and 54 in IOMF or IOMF2 enclosures (service side).
Indication of whether the ATM adapter software is automatically dumped to the specified dump file if the software abends abnormally. Automatic Dump State Enabled: The software is automatically copied. Disabled: The software is not automatically copied. Unknown:: The Automatic Dump state could not be read. The type of media or cable, such as single-mode fiber or coaxial cable, supported by the ATM CRU. Indication of whether the ATM CRU firmware is automatically updated when the ATM CRU is started.
Responsive Test Verifies that the component is connected and responding. Start Starts the ATM CRU and the associated ATM line. The ATM CRU must be in the Stopped state before you perform this action. During startup, the controller operational code is automatically loaded into the ATM CRU. When the Start action finishes, the ATM CRU and the ATM line are in the Started state. Test Verify Runs all the firmware diagnostic tests on the CRU. This test takes about three minutes to finish.
UNI Management Entity VPI The User-Network interface (UNI) management entity virtual path identifier (VPI). Maximum Number of VCIs Value: 0 through 255 The maximum number of Virtual Circuit IDs (VCIs) that can be active for permanent virtual circuits. UNI Version Maximum Number of VPIs ATM Address Registered Device State Value: 32 through 3072 The version of the User-Network Interface (UNI) supported by this ATM line.
Example: Battery (1.1.28) Attributes Battery Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical Manufacturer Identifies the manufacturer of the component. Power State Indication of whether the component is powered on. Values Logical The condition of the battery CRU. Fully Charged: The battery is fully charged. Charge State Charging: The battery is in the process of being charged.
The minimum voltage that the battery must maintain to continue operating is 39.6 volts. Lower Fatal Threshold If the battery's Total Voltage falls below 39.6, the battery is disconnected. This disconnection could cause an enclosure or the entire system to go down. The current combined voltage of both the upper and lower cells of the battery. Current Value If the Total Voltage falls below 42 volts, an alarm is generated. If the Total Voltage falls below the 39.6 volts, the battery is disconnected.
Physical Hardware Revision A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Indicates whether or not the blowers (amber) fault LED is blinking. LED State Part Number Type Value: Blinking or Off The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. The vendor hardware type. Logical Device State The state of the component as known to the operating system on the server.
Attributes CCSA Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Physical Hardware Revision Manufacturer Part Number Power State Track ID A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Identifies the manufacturer of the component. The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
if the CCSA is currently in use (and stops it only after you confirm). Test Verify Checks the health of the Common Communication ServerNet adapter (CCSA) CRU. It will determine whether the CCSA CRU can communicate with at least one SAC on the board. Disk Attributes Actions An internal 3.5-inch hard disk drive. Each disk drive connects to one of two SCSI buses on either a (PMF), IOMF) or an IOMF2 CRU.
The current state of the backup disk path. Values. The logical device number used by the operating system to identify the Logical Device Number disk. Example: 7 Media Size The total size (in kilobytes) of disk storage space. The current state of the primary disk path. Values. Primary Path State Product ID A unique number that identifies the product. Backup Path State Process Pair The 2 processors in which this I/O process is configured to run.
SCSI Controller A number (1 or 2) that identifies the backup SCSI controller that manages the disk. SCSI ID Example: SCSI Controller (1.1.50.2) An identification number assigned to the device when configured. Primary Path The accessibility of the primary path. Access State Values: Inactive, Active Configured Controller The location of the primary disk path SCSI controller. Location Example: PMF.SAC-2.GRP-1.MOD-1.
Caution: Perform this action only when instructed to by service provider, Support Note, or other notification. To update disk firmware: 1. Locate and transfer the appropriate firmware source file to your server. Disk firmware versions vary by manufacturer and model number. The correct version for one disk drive may not work for others. 2.
Reset Volume Places the volume in a state from which it can be started. Responsive Test Verifies that the disk drive is installed and responding. Start Backup Path Starts the backup path to this disk drive. When the Start action completes, the backup path is in the Started state. This action fails if both paths to this disk are down and the mirrored disk is Up. For more information, see Start Disk.
Stop Disk Terminates all paths for this disk drive. When the Stop action finishes, the paths are in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action. Stop Primary Path Terminates the primary path to the disk. When the Stop action finishes, the path is in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action.
Disk (Fibre Channel) Attributes Actions A fibre channel disk that resides in a Fibre Channel disk module (FCDM). Location in OSM Tree: System > Group > FCDM Collection > FCDM > Disk Example: Disk (111.211.1.3) Attributes Disk (Fibre Channel) Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical Device State The state of the component as known to the operating system on the server.
Media Size Primary Path State Product ID The total size (in kilobytes) of disk storage space. The current state of the primary disk path. Values. A unique number that identifies the product. Process Pair The state of the backup I/O process. Backup Execution State Values: Running, Stopped The process ID of the backup I/O process. If the state of the backup I/O process is Stopped, this will not be displayed.
Configured FSAC Location Displays the configured location of the FCSA FSAC containing the backup disk path controller. This attribute is displayed even if the physical FCSA FSAC is not present. Example: FCSA.SAC-1.GRP-111.MOD-3.SLOT-2 Identifies the backup FCSA that manages the disk. FSAC Example: FCSA FSAC (111.3.2.1) Firmware OEM Product ID The firmware product ID assigned by the supplier. Version The version of the firmware running on the disk.
Disable Drive Bypass Opens up the specified port or ports (A and/or B) on the disk drive for use. Enable Drive Bypass Shuts down the specified port or ports (A and/or B) on the disk drive. Firmware Update Updates firmware for the fibre channel disk drive. This action can be performed only when both Primary and Backup paths are in the Down state. Replace Displays the procedure for replacing the disk. Reset Backup Path Places the backup path in a state from which it can be started.
Spin Down Stops the physical spinning of the disk drive. This should be done before removing a disk drive. Both paths must be down for the action to succeed. Spin Up Starts the physical spinning of the disk drive. Start Backup Path Starts the backup path to this disk drive. When the Start action completes, the backup path is in the Started state. This action fails if both paths to this disk are down and the mirrored disk is Up. For more information, see Start Disk.
Stop Disk Terminates all paths for this disk drive. When the Stop action finishes, the paths are in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action. Stop Primary Path Terminates the primary path to the disk. When the Stop action finishes, the path is in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action.
Slot Location: E4SA CRUs can be located in slots 53 and 54 in processor enclosures (service side) or in slots 51, 52, 53, and 54 in IOMF or IOMF2 enclosures (service side). Example: E4SA $ZZLAN.E4SA0 (1.1.53) Attributes E4SA Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Physical Hardware Revision Manufacturer Part Number Power State Track ID A code that identifies the generation of the component.
Parameter: Port Number Enable ServerNet Port Enables the specified ServerNet router port on this CRU. Perform this action only as directed by OSM alarm repair actions. Parameter: Port Number Start Starts the Ethernet 4 ServerNet Adapter (E4SA) CRU and the associated Ethernet ServerNet addressable controller (ESAC). The E4SA CRU and the ESAC must be in the Stopped state before you perform this action. During startup, the controller operational code is automatically loaded into the ESAC.
Type The vendor hardware type. Logical The state of the component as known to the operating system on the server. Values A code that identifies the generation of the component provided by its Vendor Hardware Revision supplier. Device State Firmware Version The version of the firmware configuration currently loaded on the EMU. Actions Firmware Update Updates the firmware on the EMU. Replace Displays the procedure for replacing the EMU. ESS Disk Attributes Actions Enterprise Storage System disk drive.
Attributes ESS Disk Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Logical The logical device number used by the operating system to identify the Logical Device Number disk. Example: 7 The current state of the backup disk path. Values. Backup Path State Media Size The total size (in kilobytes) of disk storage space. The path that is currently accessing the disk.
Represents the actual presence of the FCSA FSAC containing the primary disk path SCSI controller. This attribute is displayed only if the physical FCSA FSAC is present. A number that uniquely identifies the port through which the disk is connected. FSAC Port Name Disk Pair Disk Pair Name The name of the ESS disk that this disk is paired with. A "-P" designation following the disk name indicates primary disk; "-M" indicates mirrored disk.
Reset Backup Path Places the backup path in a state from which it can be started. Reset Disk Places the disk in a state from which it can be started. This action might be necessary if the disk was in a STOPPED state, substate HARDDOWN; a hardware error has occurred; the disk was stopped with an ABORT command; or if a STOP or ABORT fails to put the disk into the STOPPED state, substate DOWN. Reset Primary Path Places the primary path in a state from which it can be started.
If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action. Stop Primary Path Terminates the primary path to the disk. When the Stop action finishes, the path is in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action. Stop Volume Terminates all paths for the primary and mirror drives of this volume. When the Stop action finishes, the paths are in a Down state.
addressable controller) mounted on the ServerNet/DA CRU. External disks are visible in the tree pane and in the Inventory view of the Management window. In the tree pane, expand the External Disk Collection to see the individual external disk drives. In the Inventory view, each external disk drive is listed on a separate line. External disk drives are not visible in the Physical view.
The 2 processors in which this I/O process is configured to run. Configured Processors Example: 0,1 The state of the primary I/O process. Primary Execution State Values: Running, Stopped The process ID of the primary I/O process. If the state of the primary I/O process is Stopped, this will not be displayed. Primary Process ID Example: 1,296 The state of the backup I/O process. Backup Execution State Backup Process ID Values: Running, Stopped The process ID of the backup I/O process.
Configured Controller Location The location of the primary disk path SCSI controller. Example: IOMF2.SAC-2.GRP-1.MOD-1.SLOT-50 Firmware Version The version of the firmware running on the disk. Actions Abort Backup Path Terminates operation of the backup path to the disk. When the Abort action finishes, the path is in a Hard Down state. You must use the Reset Backup Path action before you can start the path again. Abort Disk Terminates operation of the all paths for the disk.
Places the disk in a state from which it can be started. This action might be necessary if the disk was in a STOPPED state, substate HARDDOWN; a hardware error has occurred; the disk was stopped with an ABORT command; or a STOP or ABORT fails to put the disk into the STOPPED state, substate DOWN. Reset Primary Path Places the primary path in a state from which it can be started. Reset Volume Places the volume in a state from which it can be started.
Terminates the primary path to the disk. When the Stop action finishes, the path is in a Down state. If the disk drive is currently in use, a dialog box warns you and asks whether or not you want to continue with the action. Stop Volume Terminates all paths for the primary and mirror drives of this volume. When the Stop action finishes, the paths are in a Down state. Switch to Backup Path Switches processing from the primary to the backup path.
Example: External Disk Collection Attributes None. Actions None. Fan Attributes Actions A component that circulates air into the enclosure to help maintain optimal temperature. Each system enclosure contains two fans, and each fan is connected to one processor multifunction ( PMF) CRU. Location in OSM Tree: System > Group > Module > Fan Slot Location: Fan CRUs are located in slots 25 and 26 on the appearance side of processor enclosures.
Normal Minimum Value The minimum acceptable fan speed is 1800 RPM. If the speed falls below 1800, an alarm is generated. The current fan speed, measured in rotations per minute (RPM). Current Value Alarms are generated if the speed of the fan falls below 1800 (minimum RPM) or rises above 5800 (maximum RPM). The maximum acceptable fan speed is 5800 RPM. If the speed rises Normal Maximum Value above 5800, an alarm is generated. Actions Enable/Disable Restores or stops power to the fan.
Actions Set LED State Turns on or off the amber LED located on the fan. The current state is indicated by the LED State attribute. FC-AL I/O Module Attributes Actions Subcomponent of a FCDM. There are two FC-AL I/O modules in each FCDM. These modules are the interface between the FCDM elements and the host controller. They route data to and from the drives using loop A and loop B. Location in OSM Tree: System > Group > FCDM Collection > FCDM > FC-AL I/O Module Example: FC-AL I/O Module (111.211.1.
Vendor Hardware Revision A code that identifies the generation of the component provided by its supplier. Device Connection The location of the configured FCSA connected to the FC-AL I/O Module. Configured Controller Location Example: FCSA.FSAC-1.GRP-111.MOD-2.SLOT-1 The number that identifies the FCSA FSAC connected to the FC-AL I/O Fibre Channel Module. Controller Example: FCSA FSAC (111.2.1.1) Actions Blink LED Off Turns off the blinking of the FC-AL I/O Modules (amber) fault LED.
Location in OSM Tree: System > Group > FCDM Collection > FCDM Example: FCDM (111.211.1) Attributes FCDM Service State Physical Hardware Revision Manufacturer Part Number Serial Number Type A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Identifies the manufacturer of the component. The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
Path B The location of FCSA connected to the disk drive through Port B. Configured Controller Location Example: FCSA.FSAC-1.GRP-111.MOD-2.SLOT-1 Identifies the FCSA FSAC connected to the FCDM through Port B. Fibre Channel Controller Example: FCSA FSAC (111.2.1.1) Path A Configured Controller Location The location of FCSA connected to the disk drive through Port A. Example: FCSA.FSAC-1.GRP-111.MOD-2.SLOT-1 Identifies the FCSA FSAC connected to the FCDM through Port A.
action will fail. ● Locator is an optional text string to help identify the physical location of the FCDM. It must contain alphanumeric characters only. ● Alarm Panel Identifier is used for Telco systems only. Verify Path A Access Verifies that Path A from the FCDM via FC-AL I/O module A to the FCSA FSAC is responding. Verify Path B Access Verifies that Path B from the FCDM via FC-AL I/O module B to the FCSA FSAC is responding.
The location of FCSA connected to the disk drive through Port B. Configured Controller Location Example: FCSA.FSAC-1.GRP-111.MOD-2.SLOT-1 Identifies the FCSA FSAC connected to the FCDM through Port B. Fibre Channel Controller Example: FCSA FSAC (111.2.1.1) Path A Configured Controller Location The location of FCSA connected to the disk drive through Port A. Example: FCSA.FSAC-1.GRP-111.MOD-3.SLOT-1 Identifies the FCSA FSAC connected to the FCDM through Port A.
Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Physical Hardware Revision Manufacturer Part Number Track ID A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Identifies the manufacturer of the component. The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
Not required on NonStop S-series systems. Replace Launches an interactive action to assist with replacement of an FCSA. Note: This replacement procedure is intended for authorized service providers only. When initiated, OSM checks for any connected paths that do not have a backup and warns you of any connectivity loss that could result from continuing with the action. OSM also directs you to the online help for precautionary guidelines for handling the hardware.
4. Protect the equipment from electrostatic discharge: a. Place an antistatic table mat on a flat horizontal work surface near the IOAM enclosure. b. Put on an ESD wrist strap. c. Attach the grounding clip from the ESD wrist strap to any unpainted metal surface on the IOAM enclosure or on the rack in which the enclosure is installed. Caution: Do not attach the ESD grounding clip to doors or to any painted surface. 5. Press down on the ejector to unseat the adapter.
Caution: Do not attach the ESD grounding clip to doors or to any painted surface. 3. Carry the FCSA to the enclosure: a. Grasp the FCSA by its handle in one hand, while supporting the bottom edge of the FCSA with the other hand. Note: The FCSA weighs approximately 7.25 pounds (3 kilograms). b. Carry the FCSA to the back of the IOAM enclosure. c. Set the FCSA down on an antistatic mat right side up with the ejector at the top. 4.
FCSA FSAC Attributes Actions A fibre channel SAC (ServerNet addressable controller) is one of two fiber-optic plug-in cards mounted on an FCSA (Fibre Channel ServerNet adapter). Location in OSM Tree: System > Group > IOAM Enclosure > IOAM > FCSA > FSAC Example: FCSA FSAC (13.3.1.1) Note: The ports on the FCSA are numbered from top down when viewing the FCSA installed in a rack. Thus, FCSA FSAC 1 is attached to the upper port (port 1), FCSA FSAC 2 is attached to the lower port (port 2).
Ethernet port on each FESA CRU. Location in OSM Tree: System > Group > Module > FESA Slot Location: FESA CRUs can be located in slots 53 and 54 in processor enclosures (service side) or in slots 51, 52, 53, and 54 in IOMF or IOMF2 enclosures (service side). Example: FESA $ZZLAN.FESA1 (1.1.53) Attributes FESA Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK.
action. During startup, the controller operational code is automatically loaded into the SAC. When the Start action completes, both the FESA and the SAC are in the Started state. Stop Rather than automatically stopping the FESA (as the Abort action does), this action first warns you if the FESA is currently in use (and stops it only after you confirm).
Actions Responsive Test Verifies that the component is connected and responding. FXSA / FX2SA (ServerNet/FX / ServerNet/FX2) Attributes Actions The ServerNet/FX adapter (FXSA) and ServerNet/FX 2 adapter (FX2SA) field-replaceable units (FRUs) allow NonStop S-series servers to communicate with NonStop K-series servers using a fiber-optic ring.
Indication of whether the carrier level is detected by the receiver from the right direction: Right Squelch Detected FOX Cluster Number True:S quelch is detected, meaning that the carrier signal cannot be received. False: Squelch is not detected, meaning that the carrier signal can be received. Unknown: Status or type of signal being received is unknown. An integer, between 1 and 14, that identifies the node to which the ServerNet/FX or ServerNet/FX2 adapter field-replaceable unit (FRU) is connected.
Compare State The differences, if any, between the current and default firmware versions. Values Actions Add LBU Configures a ServerNet/FX or ServerNet/FX2 adapter as an LBU. An LBU is the SCF logical equivalent for the adapter. Delete LBU Removes an LBU from the system configuration database. An LBU is the SCF logical equivalent for the ServerNet/FX or ServerNet/FX2 adapter.
ServerNet/FX 2 adapter FRU in the Stopped state. The current power level is indicated by the Left Transmitter Power Level attribute. Set Right Transmitter Power Level Sets the fiber-optic transmitter LED power for the right direction on the FOX ring. High LED power is suitable for distances of 2 km through 4 km. Low LED power is suitable for distances of less than 2 km.
Example: G4SA $ZZLAN.G4SA1 (13.3.2) Attributes G4SA Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Physical Hardware Revision Manufacturer Part Number Track ID A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Identifies the manufacturer of the component. The part number of the component that was assigned in manufacturing.
Physically powers off the G4SA. Reset Places the G4SA in a state from which it can be started. Start Starts the G4SA and the associated G4SA SAC. The G4SA and the SAC must be in the Stopped state before you perform this action. Stop Rather than automatically stopping the G4SA (as the Abort action does), this action first warns you if the G4SA is currently in use (and stops it only after you confirm).
The transmission mode for the ServerNet addressable controller. Duplex Mode Hardware MAC Address Values: Half Duplex, Full Duplex, Unknown The media access control (MAC) address of the PIF hardware. Displays the actual interface that is physically present. Interface Type Link Pulse State Maximum Speed Values: Copper, Fiber, and Unknown (if nothing is plugged in) A value of Up confirms that the cable from the PIF to the LAN is connected and operational.
you if the PIF is currently in use (and stops it only after you confirm). G4SA SAC Attributes Actions A ServerNet addressable controller mounted on a G4SA (Gigabit Ethernet 4-port ServerNet adapter). Each G4SA SAC contains up to four G4SA PIFs, which correspond to the four Ethernet ports on each G4SA. Location in OSM Tree: System > Group > IOAM Enclosure > IOAM > G4SA > G4SA SAC Example: G4SA SAC $ZZLAN.G4SA1.
Dump File Name Owning Processor Displays the default naming convention for dump files. The default value ($SYSTEM.SYS00.C061D00) can be altered in SCF. The first dump file name ends in 00. Each subsequent dump file automatically receives the next sequential number. The processor to which the G4SA SAC is connected. The currently available processors that can access the resource. Processor Access List Example: 0,1,4,8,9 Firmware Version Default File Name The version of the boot firmware for the SAC.
Test Verify Runs the power-on self-test for the SAC. GESA (Gigabyte Ethernet ServerNet Adapter) Attributes Actions An adapter that connects the ServerNet connections inside a server to an Ethernet local area network (LAN). The Gigabit Ethernet ServerNet adapter is similar to the Fast Ethernet ServerNet adapter but offers enhanced performance.
The configuration type of this resource. Configured Type Device State Values: CCSA, E4SA, FESA, G4SA, GESA, TRSA, Unknown The state of the component as known to the operating system on the server. Values Actions Abort Terminates operation of the Gigabyte Ethernet ServerNet adapter (GESA) and the associated Ethernet ServerNet addressable controller (SAC). When the Abort action finishes, the GESA and the SAC are in the Stopped state.
Logical Indication of whether the service LED is on or off. On: An OSM user has turned on the service LED by using the Set Service LED State action. Service LED State Off: An OSM user has turned off the service LED by using the Set Service LED State action. Turning on the group service LED helps you locate the group for servicing. This feature is useful when a system consists of multiple enclosures.
Attributes Group Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Actions Rediscover Causes OSM to refresh and reanalyze the group and all subcomponents. Refresh refers to OSM updating the attribute values displayed in the OSM Service Connection interface. Reanalyze refers to the running of OSM incident analysis, which checks EMS event messages and creates alarms in OSM if certain conditions exist.
connectivity between specified processor on this Internal Fabric. You can specify one or all processors. The action will report any ServerNet errors between the specified processor(s) and all other processors in the system. Start ServerNet Starts all ServerNet traffic through all or specified processors on the fabric. Stop ServerNet Stops all ServerNet traffic through all or specified processors on the fabric. IOAM (I/O Adapter Module) Attributes Actions A modular I/O adapter module.
Part Number Track ID The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. A unique serial number that identifies the component. Track IDs are used for tracking components. Actions Read LCD Displays all 16 lines of the IOAMs LCD text in the Action Detail dialog box. Rediscover Causes OSM to refresh and reanalyze the I/O adaper module (IOAM) and all subcomponents.
Rack Name Rack Offset A user-defined name assigned to identify the rack in which the IOAM enclosure is located. You can enter up to eight alphanumeric characters. A number assigned to describe the location of the IOAM enclosure within the rack. An optional text string assigned to further identify the physical location of the IOAM enclosure. Locator This attribute is displayed only if a value is specified using the Set Physical Location action. For Telco systems only.
Location in OSM Tree: System > Group > Module > IOMF Slot Location: IOMF CRUs are located in slots 50 and 55 in I/O enclosures (service side). Example: IOMF (2.1.50) Attributes IOMF Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical Hardware Revision Manufacturer Part Number Power State Track ID A code that identifies the generation of the component. Hardware revision codes are used for tracking components.
The status of the storage ASIC in the CRU. Initialization State Values: Initialized, Uninitialized, Unknown Actions Disable ServerNet Port Disables the specified ServerNet router port on this CRU. Perform this action only as directed by OSM alarm repair actions. Parameter: Port Number Enable ServerNet Port Enables the specified ServerNet router port on this CRU. Perform this action only as directed by OSM alarm repair actions.
If the check fails, the Prepare to Power Off action fails and the steps that follow are not taken. If the check confirms that it is safe to power off, these preparatory steps are performed: ● If the SP on this IOMF is designated as Active Primary, resets the SP so that the peer SP becomes primary ● Disables the battery Replace Launches the Replace IOMF guided procedure, which provides step-by-step instructions for replacing the IOMF CRU.
Attributes IOMF2 Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical Hardware Revision Manufacturer Part Number Power State Track ID A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Identifies the manufacturer of the component. The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
The voltage of the SCSI-Y path, the path configured for mirrored disks on a system. SCSI-Y Voltage Storage ASIC The status of the storage ASIC in the CRU. Initialization State Values: Initialized, Uninitialized, Unknown Actions Disable ServerNet Port Disables the specified ServerNet port on this CRU. Perform this action only as directed by OSM alarm repair actions. Parameter: Port Number Enable ServerNet Port Enables the specified ServerNet port on this CRU.
Replace Launches the Replace IOMF guided procedure, which provides step-by-step instructions for replacing the IOMF2 CRU. Storage ASIC Initialization Test Prompts the storage subsystem manager process ($ZZSTO) to initialize the storage ASIC in the CRU. If initialization fails, an alarm is generated. This action is triggered automatically when a new CRU is inserted while OSM is running or when an (SCF) STATUS ADAPTER command is issued.
Actions Abort Terminates operation of the LIF. When the Abort action finishes, the LIF is in the Stopped state. Delete Deletes the LIF. Start Starts the LIF. Stop Rather than automatically stopping the LIF (as the Abort action does), this action first warns you if the LIF is currently in use (and stops it only after you confirm). Maintenance Switch Attributes Actions An Ethernet switch that allows the OSM console to communicate with the Maintenance Entity (ME) in the ServerNet switch board.
IP Address Lines Connected The IP address of the switch. Lists the port numbers of ports on the switch that have lines connected. Lists the port numbers of ports on the switch that have been disconnected Lines Disconnected (since the OSM server has been running). Configurable location identifier set in the web interface (launched by the Link Location to Web Interface action) by selecting Configuration tab > System Info > System Name. MAC Address The media access control (MAC) address of the switch.
Attributes MIOE Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Logical The configuration type of this resource. Configured Type Device State Values: CCSA, E4SA, FESA, G4SA, GESA, TRSA, Unknown The state of the component as known to the operating system on the server. Values Actions Abort Terminates operation of the MIOE. When the Abort action finishes, it is in the Stopped state. Start Starts the MIOE.
Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Logical The state of the component as known to the operating system on the server. Values Lists the processor numbers for processors that have a successful data Processors with Data Path path to the PIF. If no processor has a path, "None" is shown. Device State Example: (1) Hardware MAC Address The media access control (MAC) address of the PIF hardware.
Attributes MIOE SAC Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Logical The currently available processors that can access the MIOE CRU. Processor Access List Device State Example: 0,1 The state of the component as known to the operating system on the server. Values The processor to which the MIOE CRU is connected. Owning Processor Example: 0 Actions Abort Terminates operation of the MIOE SAC.
A set of components that share a common hardware interconnection, such as a backplane. This object applies only to S-series processor and I/O enclosures, in which each enclosure contains contains one group, and a group contains only one module. The module is considered a subcomponent of the group. IOAM enclosures contain two I/O adapter modules. Example: Module 2.1 Attributes Module Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK.
Note: On T0682AAC and later, this OSM action is also supported on Telco systems. Tests fault tolerance of the power environment within the module. If the results of the action indicate a problem, check the Power State attribute of the individual CRUs to determine where the problem lies. This action is run automatically at 2:00 a.m. daily. It can also be performed manually at any time.
Start Monitoring UPS Causes the OSM Service Connection to display and start monitoring the UPS. You are prompted to enter a User ID and Password (which are established by the administrator during initial configuration of the UPS), the IP address of the UPS, and a name (must be between 1 and 60 characters; OSM displays this name as part of the UPS object name).
Which, if any, ServerNet router ports on this CRU are disabled. OSM Disabled ServerNet Ports actions to disable or enable a ServerNet port are performed as directed by OSM alarm repair actions. Actions Disable ServerNet Port Disables the specified ServerNet port on this CRU. Perform this action only as directed by OSM alarm repair actions. Note: If the port being disabled is an NNA port connected to an External Servernet Switch, you must issue a Reset on the Primary SP in Group 1.
Attributes PIC Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical Indication of the type of plug-in card. Type Values: NNA, Serial Copper, ECL, Long-Haul Fiber, Short-Haul Fiber Logical Connector Number A unique number used to distinguish between plug-in cards on an MSEB CRU. Actions Clear Loopback Test Clears the loopback test on a plug-in card (PIC).
Caution: Do not use the external loopback test on a PIC that you believe is operating normally. Doing so shuts down ServerNet traffic through the PIC for the duration of the test (several minutes). The action isolates the MSEB port occupied by the PIC, preventing the port from sending or receiving ServerNet traffic. ServerNet traffic resumes when the test is finished. Do not use the external loopback test if alarms are present on the peer fabric (the fabric opposite the PIC you intend to test).
Attributes PIF Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Logical Valid only for FESA and GESA PIFs. Current Configured Speed The transmission rate for the ServerNet addressable controller. The transmission mode for the ServerNet addressable controller. Duplex Mode Network MAC Address Maximum Speed Values: Half Duplex, Full Duplex, Unknown The media access control (MAC) address of the PIF network.
Actions Abort Terminates operation of the PIF. When the Abort action finishes, the PIF is in the Stopped state. Configure LIF Configures the associated LIF. Start Starts the CRU's PIF. The PIF must be in the Stopped state before you perform this action. When the Start action completes, the PIF is in the Started state. Stop Rather than automatically stopping the PIF (as the Abort action does), this action first warns you if the PIF is currently in use (and stops it only after you confirm).
Manufacturer Part Number Power State Track ID Identifies the manufacturer of the component. The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Whether the component is powered on. Values A unique serial number that identifies the component. Track IDs are used for tracking components. Temperature Sensor The minimum acceptable air intake temperature is 5 degrees Celsius. If the temperature falls below 5 degrees, an alarm is generated.
Attributes PMF Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical Hardware Revision Manufacturer Part Number Power State Track ID A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Identifies the manufacturer of the component. The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts.
The status of the storage ASIC in the CRU. Initialization State Values: Initialized, Uninitialized, Unknown Actions Disable ServerNet Port Disables the specified ServerNet port on this CRU. Perform this action only as directed by OSM alarm repair actions. Parameter: Port Number Enable ServerNet Port Enables the specified ServerNet port on this CRU. Perform this action only as directed by OSM alarm repair actions.
If the checks are completed successfully, the CRU is powered off. If any of these checks fail, the CRU remains powered. The Power Off action does not disable the battery, halt the processor, or switch the SP status to Active Secondary. Use the Prepare to Power Off action to perform these operations before using the Power Off action. Prepare to Power Off Performs precautionary checks to ensure that you can safely power off the PMF2 CRU and performs steps to prepare the CRU for the Power Off action.
PMF2 (Processor Multifunction 2) Attributes Actions Each processor multifunction 2 (PMF2) CRU in a NonStop server contains these components: ● A processor and memory board (PMB), which contains a processor ● A service processor (SP) ● Two internal SCSI controllers ● One external SSAC ● And for PMF2s in Group 1 only, an MIOE (Ethernet controller) to provide connectivity between the service processor and the dedicated service LAN (for OSM).
Which, if any, ServerNet router ports on this CRU are disabled. Disabled ServerNet Ports OSM actions to disable or enable a ServerNet port are performed as directed by OSM alarm repair actions. The voltage of the SCSI-Y path, the path configured for mirrored SCSI-Y Voltage disks on a system. The voltage measured between the MOSFET switch and the diode to MOSFET Voltage the DCC. The MOSFET switch is located on the Other Rail between the alternate power supply and the DCC. The minimum voltage (39.
This action is not supported for this CRU type. See the Prepare to Power Off action. Power Off This action is not supported for this CRU type. See the Prepare to Power Off action. Prepare to Power Off Performs a precautionary check to make sure you can safely remove the CRU.
Power Supply Attributes Actions Replacement Guidelines and Precautions The power supply converts standard AC line voltage and distributes DC power to all components in its power domain.
Logical Enabled State The initial state of the power supply component at the time of discovery. Values Device State The state of the component as known to the operating system on the server. Values Actions Replace Launches an interactive action to guide you through replacement of a power supply CRU. This action is valid for IOMF2 and most PMF enclosures. It is not valid for S7000 PMF or IOMF CRUs (in which the power supply is not a customer-replaceable unit).
1. Review these important notes and cautions: ● Before handling any CRU, obtain an electrostatic discharge (ESD) protection kit. Follow the directions on the kit for replacing a CRU to prevent damage to system components. ● Power cords might contain faulty connectors that, when touched, vibrated, or flexed, can cause intermittent power or the loss of a processor. ● Before replacing a power supply, visually check the power cord without touching the power cord.
3. Lower the ejector on the power supply to its fully open position. This action disconnects the power supply from the power interface board (PIB) and the AC power cord directly behind it.
4. With one hand, grasp the handle of the power supply and slide the power supply partway out of the slot. 5. Using your other hand to support the weight of the power supply, slide the power supply all the way out of the slot. Installing the Replacement Power Supply 1. Lower the ejector on the replacement power supply to its fully open position.
2. With one hand, grasp the handle of the power supply. Use your other hand to support the weight of the power supply. Then slowly push the power supply all the way into the empty slot. 3. Raise the ejector on the replacement power supply to its fully closed position. This action connects the power supply to the power interface board (PIB) and the AC power cord directly behind it. The green power-on LED above the replacement power supply should now be lit.
Power Supply (FCDM) Attributes Actions Subcomponent of a FCDM. There are two power supplies in each FCDM. Location in OSM Tree: System > Group > FCDM Collection > FCDM > Power Supply Example: Power Supply (111.211.1.95) Attributes Power Supply Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Physical Hardware Revision A code that identifies the generation of the component.
Causes the power supplys (amber) fault LED to blink on and off. SCF Equivalent: SCF Control SAC $ZZSTO.#sac-name, deviceid(shelf,bay), LED ON Replace Displays the procedure for replacing the power supply. Power Supply (IOAM) Attributes Actions Supplies power to the IOAM. There are two IOAM power supply units in each IOAM. For information on how to replace an individual Power Supply, see the CSSI web site. Note: If a ServerNet switch board is not present, the IOAM power supplies will not appear in OSM.
Actions None. Processor Attributes Actions A processor or central processing unit (CPU). In S-series servers, a Processor is a component of the processor multifunction (PMF) customer-replaceable unit (CRU). Each processor enclosure in a NonStop S-series server contains two PMF CRUs and therefore two processors. Location in OSM Tree: System > Group > Module > PMF2 > Processor Slot Location: Processors are located on the PMF CRUs in slots 50 and 55 on the service side of processor enclosures.
Lites Register An octal value that represents the contents of a Processor register known as the Lites Register. The NonStop server type. Values Processor Type Example: NSR-V Amount of secondary cache, in megabytes. Secondary Processor Cache Size Value: 2 or 4 Whether the processors and service processors have been initialized after the most recent power-on. Initialized True: Processors and service processors have been initialized. False: Processors and service processors have not been initialized.
Whether the processor has been frozen by a hardware error: Hardware Freeze Flag True: A hardware error in this processor caused it to freeze. (Disregard the Halt Code and Lites Register values.) False: This processor has not experienced a freeze caused by a hardware error. Unknown: Hardware freeze state could not be read. Online Boot Millicode Firmware Online Boot Millicode Firmware Update is not supported for processors in S7000 PMF CRUs or on systems running G06.11 or earlier.
Online Boot Millicode Firmware Update Updates the Boot Millicode firmware running on the processor. Online Boot Millicode Firmware Update is not supported for processors in S7000 PMF CRUs or on systems running G06.11 or older. The related attributes and action will not be displayed for processors on which this action is not supported. Optional Parameter: File Name Reload Loads the operating system into the processor from a specific disk location.
Attributes SAC Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical The Physical attributes are displayed only when the SAC is a subcomponent of a CCSA. The ID assigned by the device manufacturer. Device ID Example: 0x860 The Part Number of the component that was assigned in manufacturing. Use part Part Number numbers for identifying and ordering parts. SAC Type Identifies the type of SAC. The manufacturer of the device.
Download File Version The version of the operational firmware running on the SAC. Firmware Version Default File Name The version of the boot firmware for the SAC. The name of the file to be used for a (boot) Firmware Update. Default File Version The version of the firmware to be used for a (boot) Firmware Update. The differences, if any, between the current and default boot firmware Compare State versions. Values Actions Abort Terminates operation of the ServerNet Adapter ServerNet addressable controller.
A controller that manages devices using the Small Computer System Interface (SCSI) protocol. This SCSI controller is a component of Processor Multifunction (PMF) CRUs and I/O Multifunction (IOMF) CRUs. Location in OSM Tree: System > Group > Module > PMF2 > SCSI Controller Slot Location: SCSI controllers are located on PMF CRUs in slots 50 and 55 of processor enclosures and on IOMF CRUs in slots 50 and 55 of I/O enclosures. Example: SCSI Controller (1.1.55.
fabric or the ServerNet Y fabric for a group. Location in OSM Tree: System > Group > Module > SEB Slot Location: SEBs must be located in slots 51 and 52 of processor enclosures (service side). Example: SEB (1.1.52) Attributes SEB Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical Hardware Revision Manufacturer Part Number Power State Track ID A code that identifies the generation of the component.
Replace Launches the Replace SEB guided procedure, which provides step-by-step instructions for replacing the SEB CRU. ServerNet Switch Board Attributes Actions A component of the IOAM, the ServerNet Switch Board provides ServerNet connectivity between processors, ServerNet adapters, and attached hardware devices. OSM software communicates with an internal part of the switch known as the Maintenance Entity (ME) by a connection established through the Maintenance Switch.
The VPROC of the ME FPGA (Field Programmable Gate Array) image currently loaded on the switch logic board. Default File Name The full path name of the default ME FPGA file on the server. Default File Version The version of the ME FPGA image in the default FPGA file. The differences, if any, between the current and default ME FPGA versions. Compare State Values Version ME Firmware Version The version of the ME firmware running on the switch board.
ME Firmware Update Allows you to update the firmware file for the Maintenance Entity (ME) of the ServerNet Switch Board. Power Cycle Power cycles the ServerNet Switch Board. Replace Launches the guided procedure to replace a ServerNet switch board in an IOAM or processor switch. Set LED State Turns the ServerNet Switch Board LED on or off. Soft Reset Reinitializes the firmware without affecting the ServerNet Switch Board hardware or the routing tables.
Stored Topology Master SP The maximum processor configuration for the service processor that is set the next time the system or enclosure is powered on. Values Indicates whether this service processor is the master service processor on the system: True: This is the master service processor. False: This is not the master service processor. Indicates whether the SP firmware was loaded from its own (local), the Running Image Source peer's, or the backup flash memory.
Compare State The differences, if any, between the current and default firmware versions. Values Processor Boot Millicode Firmware These attributes are displayed only for SPs located in PMF or PMF2 CRUs; not for those in IOMF or IOMF2 CRUs. The version of the firmware on the processor on the same PMF CRU with this service processor. The name of the file to be used for the Processor Boot Millicode firmware Default File Name update.
Updates the SCSI Boot Code firmware for a single service processor (SP). Available only for SPs on PMF and PMF2 CRUs. Optional Parameter: File Namefile name of the boot code file on the local node. Syntax: $volume.subvolume Default value: $SYSTEM.SYSnn SP Firmware Update Updates the firmware for a single service processor (SP). Optional Parameter: File Name -- the name of the firmware file. Syntax: $volume.subvolume Default value: $SYSTEM.
Part Number Power State Track ID The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Whether the component is powered on. Values A unique serial number that identifies the component. Track IDs are used for tracking components. Storage ASIC The status of the storage ASIC in the CRU.
Example: SSAC (1.1.50.3) Attributes SSAC Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical The type of CRU this SAC is connected to. Type values: SSAC, FSAC, SCSI The part number of the component that was assigned in manufacturing. Use Part Number part numbers for identifying and ordering parts. A unique serial number that identifies the component. Track IDs are used for Track ID tracking components.
● 5242 DAT72 tape drive (all models) ● Virtual tape subsystems (all models) ● N152x LTO tape drives (all models) SCSI-to-Fiber Converter.
Part Number The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. This is not the spare part number. Process Pair The 2 processors in which this I/O process is configured to run. Configured Processors Example: 0,1 The state of the primary I/O process. Primary Execution State Primary Process ID Values: Running, Stopped The process ID of the primary I/O process.
SWAN / SWAN2 Attributes Actions The ServerNet wide area network (SWAN) concentrator CRU is an external communications device that connects to a system through dual Ethernet ports. It supports both synchronous and asynchronous protocols over a variety of electrical interfaces. The SWAN CRU object displayed by OSM can be either a SWAN or SWAN 2 CRU. To distinguish between them, look at their subcomponents.
Logical The type of SWAN concentrator. Adapter Type Values: Synchronous or Firmware Controlled The state of the SWAN concentrator CRU as known to the operating system. Adapter State Primary Host IP Address Alternate Host IP Address Values: Started, Stopped, Starting, Stopping, Aborted, Aborting, Out Of Service, Unknown, Not Configured The primary host IP address configured for the SWAN concentrator. The alternate host IP address configured for the SWAN concentrator.
Actions Start Starts the SWAN concentrator and its associated CLIPs. When the Start action completes, the SWAN concentrator and its associated CLIPs are in the Started state. In a multisystem configuration, this action also causes the current system to take control of the associated CLIPs. If any of the CLIPs are currently controlled by another system, that system loses control of those CLIPs. Stop Terminates operation of the SWAN concentrator and all associated SWAN CLIPs.
Actions None. SWAN CLIP Attributes Actions A communications line interface processor (CLIP) is a component of a SWAN or SWAN 2 CRU. The CLIP provides a link-level protocol and a software interface to the host. Each SWAN concentrator contains up to three CLIPs, and each CLIP has two WAN Lines and two SWAN Paths. Each SWAN 2 CRU contains up to six SWAN 2 CLIPs, and each CLIP has two WAN Lines and two SWAN Paths.
The version of the firmware on the concentrator communications line interface processor (CLIP) of the ServerNet wide area network (SWAN). Default File Name The name of the file to be used for a firmware update. Default File Version The version of the firmware to be used for a firmware update . The differences, if any, between the current and default firmware versions.
Tests two-way access to the communications line interface processor (CLIP) using the primary address Test Verify Runs the power-on self-test for the CLIP. The FAULT LED on the CLIP flashes during the test. If the test passes, the FAULT LED goes off. If the test fails, the FAULT LED remains on continuously.
Attributes Fan $ZZWAN Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Logical Device State The state of the component as known to the operating system on the server. Values Actions None. SWAN LAN Logic Board (LANLB) Attributes Actions Each SWAN 2 CRU has two customer-replaceable LAN logic board subcomponents. Location in OSM Tree: System > SWAN Collection > SWAN > LANLB Example: LAN LB $ZZWAN.#SWAN2.
The status of the Ethernet link. Link State Values: Up, Down, Not Available The duplex mode of the connection between the logic board and the router. Duplex Mode Values: Half Duplex, Full Duplex, Not Available The maximum speed of the connection between the logic board and the router. Maximum Speed Values: 10Mbps, 100Mbps, Not Available The operational status of the SWAN 2 LAN logic board CRU. Board State Values: OK, Fault, Not Available Actions None.
The state of the data link control (DLC) task associated with the line as known to the operating system. DLC Task State Values: Starting, Started, Stopped, Unknown, and Indeterminate (CLIP is inaccessible). Actions External Loopback Test Performs the external loopback firmware diagnostic test. Start DLC Task Starts the data link control (DLC) task associated with the SWAN Line. When the Start action completes, the task is in the Started State.
The state of the SWAN Path as known to the operating system. Path State Values: Started, Stopped Actions Start Starts the SWAN Path. When the Start action completes, the SWAN Path is in the Started state. Stop Terminates operation of the SWAN Path. When the Stop action completes, the SWAN Path is in the Stopped state. Verify Logical Configuration Verifies that the SWAN Path is properly configured. If not, an Incorrect Logical Configuration alarm is generated on the SWAN Path.
Logical Device State The state of the component as known to the operating system on the server. Values Actions None. System Attributes Actions A system is made up of all the hardware components, software, and firmware that are managed by a single operating system. Internal hardware components are housed in enclosures and are arranged in groups, modules, and slots. User-replaceable components are known as customer-replaceable units (CRUs).
The release version update of the operating system that is running on the server. Version Example: G06.26 Other values that might be displayed for Operating System Version are Not Running and Halted. System Services Indicates whether or not the system has been configured to allow advanced storage configurations. This feature is enabled/disabled using the Enable and Disable Advanced Storage Configuration actions.
Why the creation ability was suppressed, displayed as free form text. Reason for Suppression This attribute is shown only if the Problem Incident Report Creation State value is Suppressed. The date and time the creation ability was suppressed. Time of Suppression Duration of Suppression This attribute is shown only if the Problem Incident Report Creation State value is Suppressed. How long the suppression will last (in minutes). The default value is 40 minutes.
Enable/Disable Automatic Data Collection Use to enable or disable automatic collection of data for failed system resources. The current state for the system is indicated by the Automatic Data Collection State attribute. If enabled, when a hardware failure occurs, data is saved to the location specified by the Set Data Collection Volume action. The Set Days to Persist for Diagnostic Data action determines how long the files are retained on the system before being deleted.
Removes suppression caused by the Suppress Problem Incident Report Creation action. While this suppression is automatically unsuppressed when the specified suppression time has been reached, you can choose to end the suppression immediately using this action. Tape Collection Attributes Actions When one or more tape drives are connected to a system, a Tape Collection object appears in both the tree pane and the overview pane of the OSM Service Connection.
Attributes Tape Drive Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Logical Logical Device Number The number assigned to the drive by the file system. The type of tape drive. Values. Tape Type Product ID The tape drive product identification. The accessibility of the tape drive through the tape process. Device State Values: Up, Down, Hard Down Firmware Version The version of the firmware.
Controller Path SCSI ID SCSI Controller Configured Controller Location An identification number assigned to the device when configured. The number (3) that identifies the SCSI controller that manages the tape drive. Example: SSAC (1.1.55.3) The location of the SCSI controller. Example: IOMF2.SAC-3.GRP-1.MOD-1.SLOT-55 Actions Responsive Test Verifies that the component is installed and responding. Start Puts the tape process in a state to accept regular I/O commands to the tape drive.
POST ROM EDC verified T515x Queuing and enqueuing T517x T519x Loader software reset N/A Loop write-to-read. No tape (media) is required. Microprocessor library internal loopback test T9490 Servo processor self-test Servo processor RAM test The tape drive must be in the Stopped state to perform this action. Test Verify Runs the power-on self-test for the tape drive. Additionally, runs tests to isolate problems involving the tape drive, SAC, or Common Base Board.
Hardware Revision Manufacturer Part Number Power State Track ID A code that identifies the generation of the component. Hardware revision codes are used for tracking components. Identifies the manufacturer of the component. The part number of the component that was assigned in manufacturing. Use part numbers for identifying and ordering parts. Whether the component is powered on. Values A unique serial number that identifies the component. Track IDs are used for tracking components.
Attributes Unknown CRU Service State Displayed in the Attributes tab and Attributes dialog box only if the value is something other than OK. Values Physical Power State Whether the component is powered on. Values Actions None. UPS Attributes Actions Uninterruptible power supply (UPS) unit that provides backup power for IOAM enclosures.
Displays additional information about the UPS as set by super-user in the web interface (see the Link to Web Interface action). Up to 20 characters Identificaton Information are allowed. IP Address Serial Number Example: UPS Web Card The IP address of the UPS. The unique number assigned to the UPS in manufacturing. Knowing the serial number is especially helpful when you need to replace batteries or required other service. Example: TU321A1185 Displays the UPS model version.
Collection icon in the tree pane (but not in the overview pane) to select and monitor individual CLIMs. This object disappears when there are no more CLIMs configured on the system. Location in OSM Tree: System > CLIM Collection Attributes None. Actions Configure CLIM Configures a new CLIM device on the system. You will be prompted for the CLIM name and the location of one of the ports to which the CLIM is or will be connected.
Configured X Fabric Location The Group-Module-Slot value assigned to the CLIM by the system (based on its configured location). The version of CIP/Linux running on the CLIM. The location of the ServerNet X fabric port where the CLIM is configured. Configured Y Fabric Location Example: 1.1.50.1 The location of the ServerNet Y fabric port where the CLIM is configured. Assigned Group-Module-Slot CIP/Linux Version Example: 1.1.55.
The connectivity status of the CLIM to the ServerNet X fabric. Possible values include: ● Connected: The CLIM is connected to the ServerNet X fabric. ● Cross-connected: The configured ServerNet X fabric port on the system is connected to the Y fabric port on the CLIM. ● Not Connected: The CLIM is not connected to the ServerNet X fabric. ● Not a CLIM: A device other than a CLIM is connected to the ServerNet X fabric.
Responsive Test Verifies that the CLIM is installed and responding. The CLIM must be in Started state before you can perform this action. Start Puts the CLIM in a state to accept regular I/O commands. When the Start action completes successfully, the CLIM is in the Started state. Stop Puts the CLIM in a state to disallow regular I/O commands. When the Stop action completes successfully, the CLIM is in the Stopped state.
Enabled Fault Unknown The battery can accept a charge and is ready to supply power if the AC power is unavailable. Check the battery for alarms. If the condition persists, contact your service provider. The battery is not responding, and its state cannot be determined. Compare State Value Same Up-rev Down-rev Unknown Meaning Current and default versions are the same. The current version is newer than the default version. The default version is newer than the current version. Unable to compare files.
On The component is functional. Unknown State is unknown; component might not be responding. Group Type A unique number in the system that identifies this group. Group Type is displayed in a window on the front door of the enclosure.
Power State Powered On Meaning On Off Component is powered on. Component is powered off. There might be a problem with the backup power supply for Possible Redundant Power Problem this component. (The Redundant Power Scrub action could not determine the exact cause of the problem.) There is a problem with the backup power supply for this Redundant Power Problem component (as determined by the Redundant Power Scrub action). Unknown Power state of component is unknown.
Processor Type Type NSR-W NSR-D NSR-E NSR-J NSR-G NSR-T NSR-V NSR-X NSR-H NSR-Y NSR-Z NSE-A System S7000 S7400 S7600 S7800 S70000 S72000 S74000 S76000 S78000 S86000 S88000 Integrity NonStop NS-Series server Service State Value Meaning The object is functioning properly. This value appears only in the Problem OK Summary dialog box. The resource requires operator attention.
CT9840FC-4 CT9841FC-1 CT9841FC-4 EZX-A0 M8501 M8502 M8503 M8504 M8505 N1521A N1522A N1524A N1525A T5142 T5142ACL T515 (7-9) T517x T519x T5242 T5242ACL T5242-2SE T5257 T5257ACL T5259 T5258ACL T9490 VT5801 VT5802 VT5900-A VT5900-B VT5900-C VT5901 VT5902 9840FC (Fibre Channel) cartridge tape drive mounted in a 9310 tape library Fibre Channel 9841 cartridge tape drive mounted in an L700 tape library Fibre Channel 9841 cartridge tape drive mounted in a 9310 tape library EZX Controller model A0/ETI-NET, Inc HP U
Tetra 16 The system configuration is set to support a maximum of 16 processors. Unknown Topology information cannot be determined. Prev Chapter 10. Managing a System 527274-015 Up Home Next Chapter 12.
Chapter 12. Managing a ServerNet Cluster Prev Next Chapter 12.
Locating and Viewing Cluster Resources To locate resources in a ServerNet cluster, expand the ServerNet Cluster resource in the tree pane to see the resources and connections in the cluster. To view more information about a particular resource: 1. In the tree pane, select the resource. 2. In the details pane: ● Click the Attributes tab to see attributes for the resource. ● Click the Alarms tab to see if there are alarms for the resource.
Navigate to the ServerNet Cluster resource and check the value of the ServerNet Cluster State attribute. ● Monitoring the Expand-over-ServerNet lines. Navigate to a Remote ServerNet Node resource and check the value of the Line LDEV State attribute. This value indicates the state of the line between the local node and the selected remote node. Repeat this action for all remote nodes in the cluster.
Specifying a Cluster Switch Locator String The Set Locator action allows you to specify a text string to indicate the physical location of a cluster switch. This information, which appears in the Locator attribute for the cluster switch, assists in locating the switch when maintenance is required. The maximum length for the text string (including spaces) is: ● 64 characters for the 6780 switch ● 32 characters for the 6770 switch To specify the switch location: 1.
To update ServerNet II switch firmware: 1. In the tree pane of the OSM management window, expand the ServerNet Cluster resource and navigate to the switch component of the switch module. 2. Right-click the Switch component and select Attributes. In the Firmware section, check the value of the Compare State attribute. If it is Down-rev, continue with this procedure. 3. Right-click the Switch component and select Actions. The Actions dialog box appears. 4.
Managing One of the Star Topologies With OSM Differences Between OSM and TSM OSM supports all topologies of a ServerNet cluster: the star topologies (star, split-star, and tri-star) and the newer layered topology. Differences Between OSM and TSM If you use OSM to manage a cluster with one of the star topologies, see the next paragraphs for differences between OSM and TSM.
Procedure has been streamlined and renamed. It is now launched Configure ServerNet Node by the Add Node to ServerNet Cluster action of the System resource. For more information, see Guided Procedures. For more information about using software such as SCF to manage one of the star topologies, see the ServerNet Cluster 6770 Supplement.
13 2 3 4 1 2 3 4 1 4 3 1 2 3 4 8 8 8 9 9 9 9 Router Connections for Router Interconnect PICs External Slot Internal Router Slot 4 1 2 3 3 Slot 5 1 2 3 4 Prev Chapter 11. System Resources 527274-015 Port 4 5 4 5 6 4 5 4 Up Home Next Chapter 13.
Chapter 13. Cluster Resources Prev Next Chapter 13.
Switch Fan Attributes Actions Switch Group Attributes Actions Switch Logic Board Attributes Actions Switch PIC Attributes Actions Switch Power Supply Attributes Actions Switch-to-Node PIC Attributes Actions Switch Node Port Attributes Actions Switch-to-Switch PIC Attributes Actions Switch Port Attributes Actions UPS (6770 Switch Module) Attributes Actions Common Attribute Values Service State Fabric State
Configuration Tag Port Connectivity Status A ServerNet cluster is built using one of several topologies. The hardware resources in a cluster differ depending on the topology of the ServerNet cluster. ServerNet clusters using one of the star topologies are built with the HP NonStop Cluster Switch (model 6770) and can support up to 24 nodes. ServerNet clusters using the layered topology are built around the HP NonStop ServerNet Switch (model 6780) and can support up to 64 nodes.
Example: SwitchModule $ZZSMN.Y1 Attributes Switch Module Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Logical Whether the switch is installed and responding. Presence Locator Values: Present, Absent, and Unknown User-assigned text that can be used to help identify the switch. The text is assigned by using the Set Locator action.
A hardware component that provides connectivity for multiple nodes of a second-generation ServerNet cluster using the layered topology. As part of the layered topology, the 6780 switch module comprises one cluster switch layer within a cluster switch group. The 6780 switch connects to the nodes through fiber-optic cables that connect to modular ServerNet expansion boards (MSEBs) on each node.
Locator Numeric Selector Setting Used by Firmware User-assigned text, that can be used to help identify the module. The text is assigned by using the Set Locator action. Example: Switch Group On Right in 1206 The 4-digit numeric selector setting that is currently used by the firmware. Example: 9621 Temperature The current temperature, in degrees Celsius (°C), inside the enclosure of the module. The maximum acceptable air intake temperature is 65 degrees Normal Maximum Value Celsius.
Tests the connectivity of the switch module from the local node. Set Locator Allows you to enter text to aid in locating or identifying the switch. This text is displayed as the Locator attribute. These ASCII characters cannot be used in the Set Locator field: =, +, &, or %. Also, copy and paste features do not work in this field. For more information, see Specifying a Cluster Switch Locator String. Parameter: Locator Free-form text up to 64 characters long.
Actions Replace Launches the Replace Switch Component guided procedure, which provides help for replacing the component. External ServerNet Fabric Attributes Actions This object represents a collection of switches and ServerNet links that connect the local node to other nodes in a ServerNet cluster. Location in OSM tree:The External ServerNet Fabrics (X and Y) are under the ServerNet Cluster.
Actions Node Connectivity ServerNet Path Test Checks the local node's connection to the ServerNet cluster by testing the external fabric (X or Y) between the MSEB on the local node and the cluster switch on the fabric. Remote 6770 Switch Attributes Actions The nodes connected directly to one switch see the other switches as remote switches. Although local and remote switches are the same from a hardware standpoint, less information and no actions are available for the remote switch.
Fabric Setting Whether the switch is configured for operation on the X fabric or the Y fabric. Values: X, Y, or Clear Verification that the switch is installed and responding. Presence Values: Present, Absent, Unknown The version of the configuration file currently loaded on the switch. Configuration Version Example: 1_5 The version of the firmware currently loaded on the switch. Firmware Version Example: 3_0_23 Actions None.
Current Number of Nodes The number of ServerNet nodes that are currently members of this cluster. ServerNet Cluster Service The current state of the ServerNet Cluster subsystem on the local node. ServerNet Cluster State Values: Starting, Started, Stopping, Stopped, and Unknown SCF Equivalent: SCF STATUS SUBSYS $ZZSCL SANMAN Process Pair The state of the primary SANMAN process. Primary Execution State Primary Process ID Values: Running, Stopped The process ID of the primary SANMAN process.
Actions Rediscover Causes OSM to refresh and reanalyze the object and all subcomponents. Refresh refers to OSM updating the attribute values displayed in the OSM Service Connection interface. Reanalyze refers to the running of OSM incident analysis, which checks EMS event messages and creates alarms in OSM if certain conditions exist. Reset ServerNet Statistics Resets the ServerNet statistical counters to zero for all processors in the system.
on. Location in OSM tree: Under the ServerNet Cluster Example: ServerNet Local Node \STARZ Attributes ServerNet Local Node Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Logical The state of the connection from the local node to the remote node over the external ServerNet Y fabric.
Actions Generate ServerNet Statistics Generates an event containing the ServerNet statistics from the remote node to the local node. ServerNet Remote Node Attributes Actions This object represents any system within a ServerNet cluster that is not the local node. Remote nodes are visible when the ServerNet Cluster view is selected.
The state of the connection from the local node to the remote node over the external ServerNet X fabric. Up: At least one of the processors on the local node can communicate with at least one processor on the remote node over X Fabric Connection State the X fabric. Down:No processor on the local node can communicate with any processor on the remote node over the X fabric. Unknown: The state of the connection cannot be determined.
The component of the 6770 switch module that provides routing for the cluster over an external ServerNet fabric. The ServerNet II switch connects to the nodes through fiber-optic cables that connect to plug-in cards (PICs) located on modular ServerNet expansion boards (MSEBs) on each node. Location in OSM tree: External ServerNet Fabric > Switch Group > Switch Module > Switch Example: Switch $ZZSMN.
Configuration Tag Version A parameter used by SCF and the guided procedures that allows SANMAN to select an appropriate switch configuration block (SCB) from the M6770CL switch configuration library. The selected SCB is subsequently loaded on the specified switch. The configuration tag determines the position of the cluster switch in the topology and the ServerNet node numbers supported by the cluster switch.
Optional Parameter: File name of the configuration file. Firmware Update Updates the firmware on the ServerNet II switch component of the 6770 switch module. For more information, see Updating Cluster Switches. Optional Parameter: File name of the firmware file. Hard Reset Is necessary following a Configuration Update action in order for the changes to take effect. Caution: This action disrupts the ServerNet traffic through this switch.
A component that circulates air into the enclosure to help maintain optimal temperature. Location in OSM tree: External ServerNet Fabric > Switch Group > Switch Module > Switch Fan Example: Fan (1020.1.16) Attributes Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical The state of the fault LED on the fan. LED State Values: On, Off, Blinking Whether the fan is installed and responding.
Switch Group Attributes Actions A collection of up to four 6780 switches connected together, typically mounted in a rack, that reside on one fabric of a cluster switch zone. The switch group is identified by a four-digit number. The first two digits (10) distinguish a switch group from a group within a NonStop S-series server.
Example: Switch Logic Board (1020.1.14) Attributes Switch Logic Board Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Physical Hardware Revision The hardware revision of the switch logic board. The state of the fault LED on the switch logic board. LED State Values: On, Off, On and Blinking, Off and Blinking Part Number The part number of the switch logic board. Track ID The track ID of the switch logic board.
Compare State The differences, if any, between the current and default firmware versions. Values Configuration Configuration Tag A parameter used by SCF and the guided procedures that allows SANMAN to select an appropriate switch configuration block (SCB) from the switch configuration library. The selected SCB is subsequently loaded on the specified switch. The configuration tag determines the position of the cluster switch in the topology and the ServerNet node numbers supported by the cluster switch.
Planning and Installation Guide. Optional Parameter: File Name the name of the configuration file on the local node Syntax: $volume.subvolume Default value: $SYSTEM.SYSnn Dump Copies a memory image from a 6780 switch to a specified file on the local system. Firmware Update Loads a firmware file from the local node to the switch logic board. For details, see the ServerNet Cluster 6780 Planning and Installation Guide.
Switch PIC Attributes Actions A card in the 6780 switch that plugs into the switch logic board. Most switch PICs (except for maintenance PICs and router interconnect PICs) are populated with transceivers that enable connections to the different nodes, layers, and zones of the cluster. Location in OSM tree: External ServerNet Fabric > Switch Group > Switch Module > Switch PIC Example: Switch PIC $ZZSMN.Y11.13 (1011.1.13) See also Router Connections for Router Interconnect PICs.
The initial state of the component at the time of discovery. Enabled State Enabled: The component is operational. Disabled: The component is present but not operational. Indication of whether the switch has a fault. Device State Values: OK, Fault Actions Blink LED Off Turns off the blinking of the LEDs. Blink LED On Causes the LEDs to blink on and off. Replace Invokes the Replace Switch Component guided procedure that helps to replace the switch PIC.
Whether the Power Supply is installed and responding. Presence Values: Present, Absent, Unknown The state of the fault LED on the power supply. LED State Values: On, Off, On and Blinking, Off and Blinking Track ID The track ID of the power supply. Manufacturer Identifies the manufacturer of the component. Hardware Revision The hardware revision of the power supply. Logical The initial state of the component at the time of discovery. Enabled State Enabled: The component is operational.
Attributes Switch PIC Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Logical The state of connectivity between the switch and the node to which this PIC connects. Values: Connected Not Connected Connectivity Status Connected to Switch With Wrong Fabric Connected to Node Connected to Wrong Port Connected to Different Switch Connected to Switch With Wrong Configuration Unknown Whether the PIC is installed and responding.
Switch Node Port Attributes Actions On the 6780 switch, an external transceiver port that connects to a ServerNet node.These ports reside only on switch PICs in slots 6 through 9. Location in OSM tree: External ServerNet Fabric > Switch Group > Switch Module > Switch PIC > Switch Port Example: Switch Port (1010.1.6.1) See also Router Connections for Switch Node Ports.
The status of the port.
Node Number The ServerNet node number of the neighbor node. Node Name The name of the neighbor node. Actions Node Responsive Test Tests the connectivity on the external ServerNet fabric from the local node to the remote node connected via this port. Switch-to-Switch PIC Attributes Actions A plug-in card (PIC) on the 6770 switch module that connects to another switch on the same fabric. The last part of the name contains the port number where the PIC is located.
The state of connectivity between the switch and the node to which this PIC connects. Values: Connected Not Connected Connectivity Status Connected to Switch With Wrong Fabric Connected to Node Connected to Wrong Port Connected to Different Switch Connected to Switch With Wrong Configuration Unknown Whether the PIC is installed and responding. Presence Values: Present, Absent, Unknown Neighbor Switch PIC The neighbor switch and PIC to which this PIC is connected. PIC Name Example: Switch PIC $ZZSMN.X.1.
Attributes Switch Port Displayed in the Attributes tab and Attributes dialog box only if the value is Service State something other than OK. Values Transceiver Physical The type of transceiver. Type Example: 50/125 - 62.5/125 Micron MMF Part Number The vendor part number of the transceiver. Serial Number The vendor serial number of the transceiver. Manufacturer Identifies the manufacturer of the component. Hardware Revision The vendor hardware revision of the transceiver. Logical The status of the port.
Current Speed The speed of the port in bits per second. The initial state of the component at the time of discovery. Transceiver Device State Values: OK, Fault Whether the transceiver is enabled. Transceiver Enabled State Enabled: The component is operational. Disabled: The component is present but not operational. Neighbor Switch Port The name of the port to which this port is connected. Format: Port (Group.Module.Slot.Port) where: Switch Port Group can be 1010, 1020, 1030, 1011, 1021 or 1031.
Physical Manufacturer Identifies the manufacturer of the component. Part Number The part number of the UPS. The VA rating (volts multiplied by amps) and the firmware version of the UPS. Type Example: UPS 1440 VA FW -0039 Logical Estimated Charge Remaining The percentage of charge remaining in the UPS batteries.
The resource requires operator attention. This condition sometimes generates an alarm, and the component that requires attention is colored Attention Required yellow in the tree pane and in the Physical and ServerNet views of the view pane. The resource requires service. This condition generates an alarm, and the Service Required component that requires service is colored red in the tree pane and in the Physical and ServerNet views of the view pane.
Link alive, port disabled, neighbor check complete Link alive, port disabled, neighbor check failed (Not connected) Link alive, port disabled, neighbor check failed (Connected to switch) Link alive, port disabled, neighbor check failed (Connected to node) Link alive, port disabled, neighbor check failed (Connected to switch with invalid configuration version identifier) Link alive, port disabled, neighbor check failed (Connected to switch with incompatible configuration Link alive, port disabled, neighbor c
Chapter 14. Updating ServerNet Cluster Topology Prev Next Chapter 14.
● Migrating to the Layered Topology describes how to migrate a cluster from one of the star topologies to the layered topology. ● Adding Zones or Layers to a Layered Topology describes how to add zones or layers to a cluster already using the layered topology.
These three methods are supported for updating to the split-star or tri-star topology: ● Merging two star topologies to create a split-star topology ● Merging a star topology with a split-star topology to create a tri-star topology ● Merging three star topologies to create a tri-star topology The major steps in updating a topology are: 1. Review the planning information in the ServerNet Cluster Manual for your type of update.
to support node numbers 17 through 24. (The remaining star topology should already use node numbers 1 through 8.) Note: Changing the configuration tag requires a hard reset of the switches, resulting in a temporary disruption of ServerNet connectivity. After the configuration tags match on respective X and Y switches, the connectivity is repaired. 8. Perform the Update Topology action on each cluster. When prompted, click the Disable Cluster Alarms button.
Software Requirements for Split-Star and Tri-Star Topologies Any node that will participate in a ServerNet cluster must have Expand (T9057) software, which is delivered on the site update tape (SUT). In addition, the Expand/ServerNet Profile (T0569) is required for clustering. If you order the optional Expand/ServerNet Profile component, it is delivered on the SUT. Additional software requirements depend on the topology you use to construct the ServerNet cluster: Software Component Split-Star Topology G06.
X1 X1 X1 Y1 Y1 Y1 Y1 9 10 11 8 9 10 11 X2 X2 X2 Y2 Y2 Y2 Y2 9 10 11 8 9 10 11 Updating to the Tri-Star Topology If you are updating to the tri-star topology, connect the cables as follows: Cluster Switch X1 X1 X1 X1 X2 X2 Y1 Y1 Y1 Y1 Y2 Y2 Port Connects to Cluster Switch 8 X2 9 X2 10 X3 11 X3 8 X3 9 X3 8 Y2 9 Y2 10 Y3 11 Y3 8 Y3 9 Y3 Port 10 11 8 9 10 11 10 11 8 9 10 11 Cable Connections in a Layered Topology Connections Between Layers Within a Switch Group X Fabric Connections Between Two Zones Y Fa
X11/Y11 X11/Y11 X11/Y11 X11/Y11 X11/Y11 X11/Y11 X11/Y11 X11/Y11 X11/Y11 X11/Y11 X11/Y11 X11/Y11 X12/Y12 X12/Y12 X12/Y12 X12/Y12 X12/Y12 X12/Y12 X12/Y12 X12/Y12 X13/Y13 X13/Y13 X13/Y13 X13/Y13 11 11 11 11 12 12 12 12 13 13 13 13 12 12 12 12 13 13 13 13 11 11 11 11 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 X12/Y12 X12/Y12 X12/Y12 X12/Y12 X13/Y13 X13/Y13 X13/Y13 X13/Y13 X14/Y14 X14/Y14 X14/Y14 X14/Y14 X14/Y14 X14/Y14 X14/Y14 X14/Y14 X13/Y13 X13/Y13 X13/Y13 X13/Y13 X14/Y14 X14/Y14 X14/Y14 X14/Y14 11 1
X13 X13 X13 X14 X14 X14 X14 2 3 3 2 2 3 3 2 1 2 1 2 1 2 X23 X23 X23 X24 X24 X24 X24 2 3 3 2 2 3 3 1 2 1 2 1 2 1 Y Fabric Connections Between Two Zones This table lists the Y-fabric connections between two zones of a layered topology: Switch PIC Slot Port Connect to Switch PIC Slot Port Y11 2 1 Y21 2 2 Y11 2 2 Y21 2 1 Y11 3 1 Y21 3 2 Y11 3 2 Y21 3 1 Y12 2 1 Y22 2 2 Y12 2 2 Y22 2 1 Y12 3 1 Y22 3 2 Y12 3 2 Y22 3 1 Y13 2 1 Y23 2 2 Y13 2 2 Y23 2 1 Y13 3 1 Y23 3 2 Y13 3 2 Y23 3 1 Y14 2 1 Y24 2 2 Y14 2 2 Y24
X12 X12 X12 X13 X13 X13 X13 X14 X14 X14 X14 X21 X21 X22 X22 X23 X23 X24 X24 2 3 3 2 2 3 3 2 2 3 3 2 3 2 3 2 3 2 3 2 1 2 1 2 1 2 1 2 1 2 1 1 1 1 1 1 1 1 X32 X22 X32 X23 X33 X23 X33 X24 X34 X24 X34 X31 X31 X32 X32 X33 X33 X34 X34 2 3 3 2 2 3 3 2 2 3 3 2 3 2 3 2 3 2 3 1 2 1 2 1 2 1 2 1 2 1 2 2 2 2 2 2 2 2 Y Fabric Connections for Three Zones This table lists the Y-fabric connections for three zones of a layered topology: Switch PIC Slot Port Connect to Switch PIC Slot Port Y11 2 1 Y21 2 2 Y11 2 2 Y31 2 1
Y14 Y14 Y21 Y21 Y22 Y22 Y23 Y23 Y24 Y24 3 3 2 3 2 3 2 3 2 3 1 2 1 1 1 1 1 1 1 1 Prev Chapter 13.
Glossary Prev Next Glossary A|B|C|D|E|F|G|H|I|J|K|L|M|N|O|P|Q|R|S|T|U|V|W|X|Y|Z A action An operation, such as a diagnostic test, that can be performed on a selected resource. Use the Actions dialog box to display and perform actions. Examples: Load (action on a selected processor) Up (action on a selected disk) AC transfer switch A component of a NonStop" Cluster Switch (model 6770) that provides access to dual AC power sources and the ability to switch between the two sources if one fails.
appearance side The side of an HP NonStop" S-series system enclosure that contains disk customer-replaceable units CRUs and power monitor and control unit (PMCU) CRUs that do not require cables. The appearance side always has a short door and panel, or a tall door, that is required for cooling the enclosure. The appearance side is opposite the service side. The appearance-side door is lockable for security purposes.
in one processor has no effect on any other processor. blower A variable speed airflow device that pulls air into an enclosure or element. It usually pulls air in from the front and exhausts the heated air out the rear. board A frame on which computer circuitry is mounted. Same as logic board. boot A synonym for load. bus A system or subsystem data path that provides serial or parallel interconnection for multiple modules or components.
Switch. The subcomponents include the ServerNet II Switch, the AC transfer switch, and the uninterruptible power supply (UPS). A cluster switch enclosure resembles, but is half the height of, a standard HP NonStop S-series system enclosure. cluster switch group Within an external ServerNet fabric, all the cluster switches that belong to the same cluster switch zone. A cluster switch group can consist of up to four 6780 switches, each representing one cluster switch layer.
The major programmable device within the ServerNet wide area network (SWAN) concentrator, providing link-level protocol and a software interface to the host. The CLIP stores and implements specific communications protocols. connection A logical link established between the OSM client software on the system console and the OSM server software on a NonStop server after a logon sequence has been performed. There are two types of connections: service connection and low-level link.
Incident reports are sent from the OSM workstations defined as the primary and backup dial-out points (the primary and backup system consoles. Note: Remote access and remote notification are not available in countries where the modem provided by HP is not certified. In these countries, you cannot use the OSM software to dial out to or accept dial-in communications from a service provider.
E EMU (Environmental Monitoring Unit) An element which monitors the status of an enclosure, including the power, air temperature, and blower status. The EMU detects problems and displays and reports these conditions to a user and the controller. In some cases, the EMU implements corrective action. enclosure A single sheet-metal structure and its enclosed set of system components.
The fabrics that link systems in a ServerNet cluster. external ServerNet X or Y fabric The X or Y fabric that links systems in a ServerNet cluster. F fabric A complex set of interconnections through which there can be multiple and (to the user) unknown paths from point to point. The term fabric is used to refer to the X or Y portion of the ServerNet communications network; for example, the X fabric. See also internal ServerNet fabric and external ServerNet fabric.
A programmable integrated circuit that can be customized to perform specific functions. field-replaceable unit (FRU) A unit that can be replaced in the field only by qualified personnel trained by HP and cannot be replaced by customers. A unit is classified as a FRU because of safety hazards such as weight, size, sharp edges, or electrical potential; contractual agreements with suppliers; or national or international standards. See also customer-replaceable unit (CRU).
A unique, read only number stored in nonvolatile memory (SEEPROM) on a ServerNet II Switch at the time of manufacture. The GUID also appears on the bar code label. This number can be used programmatically to identify the switch. group Part of the group, module, slot naming convention for uniquely identifying the logical location of a component within a system. A group is a subset of a system and contains one or more modules.
supply (UPS), and AC transfer switch, and it can be packaged in a switch enclosure or in a 19-inch rack. The cluster switch is used with star, split-star, and tri-star topologies. See also HP NonStop Cluster Switch (model 6780). HP NonStop ServerNet Switch (model 6780) The cluster switch used in the layered topology. The 6780 switch consists of a switch logic board, a midplane, plug-in cards, power supplies, and fans. See also HP NonStop Cluster Switch (model 6770).
See also fabric. internet protocol (IP) A data communications protocol that handles the routing of data through a network, which typically consists of many different subnetworks. IP routes data between source and destination IP addresses. I/O adapter module (IOAM) A collection of modular components that provides I/O connectivity and can include ServerNet switch boards, Fibre Channel ServerNet adapters (FCSAs), fans, and power supplies.
One of several views of a server or supported Expand network available after system discovery in the view pane of the Management window. The Inventory view is a table that lists server or cluster components according to type, location, part number, and other attributes. See also Physical View. IP address An internet protocol (IP). An IP address consists of two parts: a network address, which identifies the network, and a local address, which identifies a host within a network.
link A communications path between two entities. load To transfer the NonStop Kernel operating system image or a program from storage (typically disk) into processor memory so that the operating system or program can run. local area network (LAN) A network that is located in a small geographical area and provides a high-bandwidth, low-cost medium to which low-cost nodes can be connected.
the external Y fabric of a ServerNet cluster. See also SP logical name. logical processor The combination of equivalent processor elements in the Blade Elements that are running in the same instruction stream in loose lock-step. Logical Unit Number (LUN) A SCSI convention used to identify elements. The host sees a virtual disk as a LUN. The LUN address a user assigns to a virtual disk for a particular host will be the LUN at which that host will see the virtual disk.
nodes). The overview pane does not appear in the OSM Low-Level Link. The top pane is the view pane. It might contain a Physical view or an Inventory view. You can select the type of view from the Display menu or the toolbar. The lower pane is the details pane. It displays the specific information about the selected resource. Click a tab to select the type of information to display in the details pane.
suffix to show which drive is the primary (-P) and which is the mirror (-M). See also volume. modular ServerNet expansion board (MSEB) A ServerNet expansion board (SEB) that uses plug-in cards (PICs) to provide a choice of connection media for routing ServerNet packets. modular cabinet A cabinet with an integrated standard 19-inch rack equipped with a power distribution unit (PDU), doors, slides, brackets, castors, leveling pads, and optional side panels.
N name For the OSM software, the name attribute is determined by the connection type. When you use the service connection, the logical name is used. When you use the low-level link, the service processor (SP) logical name is used. Examples of logical names: ● $DATA04-P is the logical name of the disk CRU located in group 1, module 1, slot 13. ● IOMF2.SCSI-3.GRP-1.MOD-1.SLOT-50 is the logical name of the third SCSI bus on the IOMF2 CRU located in group 1, module 1, slot 50.
O object One or more of the devices, lines, processes, and files in a subsystem. In the OSM Service Connection, an object is equivalent to a resource. See also resource. OSM Event Viewer A component of the OSM software that lets you set up criteria to view log files in several ways, enabling you to rapidly assess service problems. The OSM Event Viewer is launched from within the OSM Low-Level Link and the OSM Service Connection.
P PAL firmware The Processor Abstraction Layer is firmware that directly handles all aborts and initialization and platform management interrupts. part number A unique number assigned to a product. The part number can be used for ordering purposes. path The route between a processor and a subsystem. If a subsystem is configured for fault tolerance, it has both a primary path (from the primary processor) and a backup path (from the backup processor).
of a resource. For example: GRP-2.MOD-1.SLOT-8. Physical view One of several views available in the view pane of the Management window. The Physical view of a server is a view of all the enclosures and is intended to represent the actual floor plan at the site. A Physical view of an enclosure is a visual representation of the physical location of supported resources inside the enclosure.
In system enclosures with power shelves, the component located in the power shelf that converts standard AC line voltage into DC voltage and delivers it to the CRUs in that enclosure, which in turn supply the DC voltages needed by the group components in the enclosure. primary processor The processor that is designated as owning the ServerNet addressable controller (SAC) connected to separate processors running the NonStop Kernel operating system.
multifunction I/O board ( MFIOB), and the power supply subassembly. processor multifunction (PMF) 2 CRU A NonStop S-series customer-replaceable unit ( CRU) that contains a power supply, service service processor (SP), ServerNet router 2, Ethernet controller, three ServerNet addressable controllers ( SACs), and a processor and memory system in a single unit.
remote switch An HP NonStop Cluster Switch (model 6770) or HP NonStop ServerNet Switch (model 6780) in a ServerNet cluster that is not directly connected to the server that you are logged on to. The OSM Service Connection cannot perform any actions on a remote switch. To perform actions or get additional information on a remote switch, use the OSM Service Connection to log on to a server that is directly connected to the switch.
serial copper plug-in card (PIC) A plug-in card (PIC) for the modular ServerNet expansion board (MSEB) and I/O multifunction (IOMF) 2 customer-replaceable unit (CRU) that supports the serial copper interface. serial maintenance bus (SMB) A bus that connects service processors within an enclosure to each other and to the customer-replaceable units (CRUs). See also serial maintenance bus (SMB) domain and power domain.
ServerNet expansion board (SEB) A connector board that plugs into the backplane to allow one or more ServerNet cables to exit the rear of the enclosure. The ServerNet expansion boards (SEBs) and cables allow processors in one group to communicate with processors in another group. Each SEB provides either the ServerNet X fabric or the ServerNet Y fabric for a group. SEBs are customer-replaceable units (CRUs).
service connection A connection between the system console and the OSM software on a NonStop server. A service connection is initiated from the browser on the system console and can be used to communicate with the server only when the NonStop operating system is running. The OSM Service Connection provides a comprehensive service and maintenance picture of the server or ServerNet cluster and is used to perform most service management tasks. See also low-level link.
A physical labeled space or sheet-metal frame in an enclosure into which a logic board or other system component can be installed. Slots have numbers that are unique in the enclosure. small computer system interface (SCSI) An ANSI-standard protocol used by a controller for access to a device. For example, the disk drives in NonStop S-series servers are connected on a SCSI bus.
A network topology in which all nodes are connected to a central hub (HP NonStop Cluster Switch). Each node has its own connection to the network, so a break in the connection does not affect other nodes in the network. In a ServerNet cluster, a star topology requires one cluster switch for each external fabric and can support up to eight nodes. See also split-star topology, and tri-star topology, and layered topology.
A subvolume on the $SYSTEM volume that contains a version of the NonStop Kernel operating system image. The letters nn represent an octal number in the range %00 through %77. There might be several SYSnn subvolumes, only one of which contains the current OSIMAGE.
A tetrahedral topology of NonStop S-series servers that allows a maximum of eight processor enclosures (16 processors). The maximum number of I/O enclosures allowed by the Tetra 16 topology varies depending on the release version update (RVU) and the server model. Contrast with Tetra 8 topology. tetrahedron A solid bounded by four triangular faces. In ServerNet context, a tetrahedron is four processors interconnected by ServerNet links so as to form a conceptual tetrahedron.
ServerNet Cluster view. The System view bears the name of the local system and displays resources within the system. The ServerNet Cluster view displays resources in a supported Expand network, such as a ServerNet cluster. See also details pane and view pane. tri-star topology A network topology that uses up to three HP NonStop Cluster Switches for each external fabric. External routing is implemented between the three star groups of a ServerNet cluster.
contract. These features include: ● The generation of incident reports and EMS event messages related to incident reports ● The ability to configure the dial-out phone number ● Support for dial-in on a system console Recommended repair actions associated with alarms vertical tetrahedron ● A topology of NonStop S-series servers in which the ServerNet connections between the layers of a cluster switch group form a tetrahedron See also tetrahedron, tetrahedral topology, and cluster switch layer.
workstation See system console. X X fabric The X side of the internal or external ServerNet fabrics. See also fabric. Y Y fabric The Y side of the internal or external ServerNet fabrics. See also fabric. Z There are no entries for this section Prev Chapter 14.
Index Prev Index Symbols 6770 Switch Module about, 6770 Switch Module actions, Actions attributes, Attributes 6780 Switch Module about, 6780 Switch Module actions, Actions attributes, Attributes A AC Power State, Logical AC Transfer Switch about, AC Transfer Switch actions, Actions attributes, Attributes Access State, Backup Path actions automatically initiating, Performing Actions on a Selected Resource detailed information about, Performing Actions on a Selected Resource on multiple resources, Performin
Active Path, Logical Adapter State, Logical Adapter Type, Logical Advanced Storage Configuration State, System Services Alarm indicators, Alarm Indicators Alarm Panel Identifier, Physical Location Alarm severity, Alarm Severity alarms deleting, Deleting Alarms detailed information, Viewing a Summary of Alarms details of, Viewing Alarm Details finding, Viewing a Summary of Alarms in Details pane, Viewing the Alarms Tab printing information, Viewing Alarm Details saving information, Viewing Alarm Details sort
ATM3SA (see ATM Adapter CRU) attributes actions for, Using the Attributes Dialog Box to View Attributes in Details pane, Using the Details Pane to View Attributes printing, Using the Attributes Dialog Box to View Attributes saving, Using the Attributes Dialog Box to View Attributes seeing description, Using the Attributes Dialog Box to View Attributes suppressing, Suppressing Problem Attributes using dialog box, Using the Attributes Dialog Box to View Attributes viewing, Viewing Attributes Automatic Boot St
Blower (FCDM) about, Blower (FCDM) actions, Actions attributes, Attributes Board State, Logical C CCSA CRU about, CCSA (Common Communication ServerNet Adapter) actions, Actions attributes, Attributes Charge State, Logical Charge Status, Logical CLIM, CLIM CLIM Collection, CLIM Collection Cluster about, ServerNet Cluster actions, Actions attributes, Attributes cluster resources list of, Cluster Resources locating, Locating and Viewing Cluster Resources managing, Cluster Resources monitoring, Monitoring a Cl
Compare State values, Compare State Configuration Tag, Physical Configuration Update, Configuration Update Configuration Version, Physical Configured Controller Location, Backup Path Configured FSAC Location, Primary Path Configured Interface Type, Logical Configured Processors, Process Pair Configured Type, Logical Connect to UPS, Connect to UPS Connectivity State, Expand-Over-ServerNet Configuration Connectivity Status, Logical Connector Number, Logical Contact, Logical CRU Type, Physical Current Configur
Device Status, Logical Diagnostic Data Collection Volume, Data Collection Services Disabled ServerNet Ports, Logical Disk ESS, ESS Disk External, External Disk Fibre Channel, Disk (Fibre Channel) Disk (Fibre Channel) about, Disk (Fibre Channel) actions, Actions attributes, Attributes Disk CRU about, Disk actions, Actions attributes, Attributes Disk Pair Name, Disk Pair Display menu, Display Menu DLC Task Name, Logical DLC Task State, Logical Download File Name, Logical Download File Version, Logical Downloa
EMU about, EMU actions, Actions attributes, Attributes Enabled State, Logical Enabled State values, Enabled State Enterprise Storage System Disk drive, ESS Disk ESS Disk about, ESS Disk actions, Actions Estimated Charge Remaining, Logical Ethernet 4 ServerNet Adapter (see E4SA CRU) Expand Node Number, Logical External Disk about, External Disk actions, Actions attributes, Attributes External Disk Collection about, ESS Disk Collection external fabric about, External ServerNet Fabric actions, Actions attribut
attributes, Attributes for IOAM, Fan (IOAM) Fan Voltage, Logical Fast Ethernet ServerNet Adapter about, FESA (Fast Ethernet ServerNet Adapter) FC-AL I/O Module about, FC-AL I/O Module actions, Actions attributes, Attributes FCDM about, FCDM actions, Actions attributes, Attributes FCDM Collection about, FCDM Collection attributes, Attributes FCSA about, FCSA actions, Actions attributes, Attributes removing and installing, Removing and Installing a Fibre Channel ServerNet Adapter FCSA FSAC about, FCSA FSAC ac
Firmware Compare State, ME Firmware Firmware Default File Name, ME Firmware Firmware Default File Version, ME Firmware Firmware Revision, Logical Firmware State, Logical Firmware update Switch Logic Board, Firmware Update firmware updates performing, Performing Firmware Updates Firmware Version, ME Firmware Firmware version, Logical FOX Cluster Number, Logical FPGA code update Switch Logic Board, FPGA Update FSAC, Primary Path about, FSAC (Fiber ServerNet Addressable Controller) actions, Actions attributes,
about, G4SA SAC actions, Actions attributes, Attributes GESA CRU about, GESA (Gigabyte Ethernet ServerNet Adapter) actions, Actions attributes, Attributes Gigabyte Ethernet ServerNet Adapter (see GESA CRU) Globally Unique ID, Logical Group (I/O or Processor Enclosure) about, Group (I/O or Processor Enclosure) actions, Actions attributes, Attributes Group (IOAM) about, Group (IOAM) actions, Actions attributes, Attributes Group Type, Group Type GUID, Physical H Halt Code, Logical Halt Flag, Logical Hard Rese
Identificaton Information, Physical Initialization State, Storage ASIC Initialized, Logical Interface Type, Logical internal fabric about, Internal ServerNet Fabric actions, Actions attributes, Attributes Internal ServerNet Fabric about, Internal ServerNet Fabric Internet Explorer menu bar, Internet Explorer Menu Bar Inventory view displaying, Using the Inventory View of a local system, Inventory View of a Local System of a ServerNet cluster, Inventory View of a ServerNet Cluster saving information, Using t
about, IOMF2 (I/O Multifunction 2) actions, Actions attributes, Attributes IP Address, Logical L Last Reset Type, Logical LED State, Physical Left Squelch Detected, Logical Left Transmitter Power Level, Logical LIF about, LIF actions, Actions attributes, Attributes LIF State, Logical Line LDEV, Expand-Over-ServerNet Configuration Line LDEV Name, Expand-Over-ServerNet Configuration Line LDEV State, Expand-Over-ServerNet Configuration Lines Connected, Logical Lines Disconnected, Logical Link Pulse State, Log
M MAC Address, Logical Main Rail Voltage, Logical Main Rail Voltage After Fuse, Logical Maintenance Switch about, Maintenance Switch actions, Actions attributes, Attributes Management window details pane, Using the Management Window overview pane, Using the Management Window tree pane, Using the Management Window using, Using the Management Window view pane, Using the Management Window managing a system, Managing a System Master SP, Logical Maximum Number of Nodes, Logical Maximum Number of VCCs, Logical Ma
actions, Actions attributes, Attributes MIOE SAC about, MIOE SAC actions, Actions attributes, Attributes Modular ServerNet expansion board (see MSEB) Module about, Module actions, Actions attributes, Attributes Monitored Service LAN Devices about, Monitored Service LAN Devices actions, Actions MOSFET Voltage, Logical MSEB about, MSEB actions, Actions attributes, Attributes N Neighbor Node Name, Neighbor ServerNet Node Neighbor ServerNet Node Number, Neighbor ServerNet Node Neighbor Switch Port, Neighbor Sw
O OEM Product ID, Firmware OSM Service Connection error messages, OSM Service Connection Session Error Messages OSM toolbar, OSM Toolbar Features and Menu Options Other Rail Voltage, Logical Other Rail Voltage After Fuse, Logical overview pane, description, Using the Management Window Owning Processor, Logical P Part Number, Physical Path State, Logical Path State values, Path State Physical Transmission Type, Logical Physical view displaying enclosure, Physical View of an Enclosure displaying system, Phys
PMF about, PMF (Processor Multifunction) actions, Actions attributes, Attributes PMF2 about, PMF2 (Processor Multifunction 2) actions, Actions attributes, Attributes Port A Bypass State, Physical Port A World Wide Name, Physical Port B Bypass State, Physical Port B World Wide Name, Physical Port Connectivity Status, Logical Port Connectivity Status values, Port Connectivity Status Port Name, Backup Path Position ID, Configuration Power State, Physical Power State values, Power State Power Supply about, Powe
Primary Execution State, Process Pair Primary Gateway IP Address, Logical Primary Host IP Address, Logical Primary Path State, Logical Primary Process ID, Process Pair Primary Rail Power State, Logical Primary Subnet Mask, Logical Primary Subnet Name, Logical Primary TCP/IP Process, Logical Problem Incident Report Creation State, Incident Report Configuration Processor about, Processor actions, Actions attributes, Attributes Processor Access List, Logical Processor Freeze Enabled State, Logical Processor Mu
Remaining Time, Logical Remote 6770 Switch about, Remote 6770 Switch attributes, Attributes Remote Line LDEV State, Expand-Over-ServerNet Configuration Remote Node about, ServerNet Remote Node actions, Actions attributes, Attributes Replace, Replace Reset Statistics, Reset ServerNet Statistics resource finding, Using the Browser's Find Feature Responsive Test, Responsive Test Right Squelch Detected, Logical Right Transmitter Power Level, Logical Ring Open Status, Logical Ring State, Logical ROM Version, Log
SCSI Extender, Storage Router SCSI ID, Backup Path SCSI SAC (see SSAC) SCSI-to-Fiber Converter, Storage Router SCSI-X Voltage, Logical SCSI-Y Voltage, Logical SEB about, SEB actions, Actions attributes, Attributes Secondary Processor Cache Size, Logical Serial Number, Physical ServerNet cluster, ServerNet Cluster cluster actions, Actions cluster attributes, Attributes external fabric, External ServerNet Fabric internal fabric, Internal ServerNet Fabric Local Node, ServerNet Local Node Local Node actions, Ac
about, ServerNet Switch Board actions, Actions attributes, Attributes ServerNet view displaying, Physical View of the ServerNet Cluster using, Physical View of the ServerNet Cluster ServerNet/DA (see about) ServerNet/FX (see FXSA FRU) Service LED State, Logical Service Processor (SP) about, Service Processor (SP) actions, Actions attributes, Attributes Service State, ATM3SA Service State values, Service State Set Fabric Setting, Set Fabric Setting Set Locator, Set Locator Set ServerNet Cluster State, Set Se
about, Storage Router actions, Actions attributes, Attributes Stored Topology, Logical Summary menu, Summary Menu SWAN Battery about, SWAN Battery attributes, Attributes SWAN CLIP about, SWAN CLIP actions, Actions attributes, Attributes SWAN Collection about, SWAN Collection SWAN Fan about, SWAN FAN actions, Actions attributes, Attributes SWAN LAN Logic Board (see about) SWAN LANLB about, SWAN LAN Logic Board (LANLB) actions, Actions attributes, Attributes SWAN Line about, SWAN Line actions, Actions attribu
about, SWAN (Power Supply) actions, Actions attributes, Attributes SWAN/SWAN2 CRU about, SWAN / SWAN2 actions, Actions attributes, Attributes Switch Fan about, Switch Fan actions, Actions attributes, Attributes Switch Group about, Switch Group Switch Logic Board about, Switch Logic Board actions, Actions attributes, Attributes Switch Node Port about, Switch Node Port actions, Actions attributes, Attributes Switch PIC about, Switch PIC actions, Actions attributes, Attributes Switch Port about, Switch Port at
Switch SNETMON Process Pair, Switch SNETMON Process Pair Switch-to-Node PIC about, Switch-to-Node PIC attributes, Attributes Switch-to-Switch PIC about, Switch-to-Switch PIC attributes, Attributes system locating resources, Locating and Viewing System Resources managing, Managing a System monitoring resources, Monitoring a System performing actions, Performing Actions on a System viewing resources, Locating and Viewing System Resources System about, System actions, Actions attributes, Attributes system reso
Time of Last Soft Reset, Logical Time of Suppression, Incident Report Configuration Token Ring ServerNet Adapter CRU (see TRSA CRU) Tools menu, Tools Menu Topology, Logical Topology values, Topology Total Memory Size, Logical Track ID, Physical Transceiver Device State, Logical Transceiver Enabled State, Logical Transceiver Hardware Revision, Transceiver Physical Transceiver Part Number, Transceiver Physical Transceiver Serial Number, Transceiver Physical Transceiver Type, Transceiver Physical tree pane, de
actions, Actions attributes, Attributes UPS (IOAM) about, UPS actions, Actions attributes, Attributes UPS Location, Physical V VA Rating, Physical Vendor Hardware Revision, Logical Vendor Product ID, Logical Vendor Product Revision, Logical Version, Firmware view pane, description, Using the Management Window W window printing, Using the Management Window Windows menu, Windows Menu World Wide Name, Physical X X Fabric Connection State, Logical Y Y Fabric Connection State, Logical Prev Glossary 527274-01
Legal Notice © Copyright 2006 Hewlett-Packard Development Company L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendors standard commercial license. The information contained herein is subject to change without notice.
OSF software and documentation are based in part on the Fourth Berkeley Software Distribution under license from The Regents of the University of California. OSF acknowledges the following individuals and institutions for their role in its development: Kenneth C.R.C. Arnold, Gregory S. Couch, Conrad C. Huang, Ed James, Symmetric Computer Systems, Robert Elz. © 1980, 1981, 1982, 1983, 1985, 1986, 1987, 1988, 1989 Regents of the University of California.
Version and Copyright Information Document Title OSM User's Guide Abstract The HP NonStop" Open System Management (OSM) software is a collection of client/server applications that provide troubleshooting, maintenance, and service tools for the HP NonStop server. The OSM software also allows you to view and manage resources within a supported Expand network, such as an HP NonStop ServerNet Cluster.