HP Notebook User Guide
© Copyright 2013 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor. AMD is a registered trademark of Advanced Micro Devices, Inc. in the U.S. and other countries. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ..................................................................................................................... 3 Top .....................
Turning the embedded numeric keypad on and off .......................... 20 Switching key functions on the embedded numeric keypad ............. 21 Using the integrated numeric keypad (select models only) ............................... 21 Using an optional external numeric keypad ...................................................... 21 Using the TouchPad ...........................................................................................................................
Identifying low battery levels ............................................................................. 35 Resolving a low battery level ............................................................................. 36 Resolving a low battery level when external power is available ....... 36 Resolving a low battery level when a charged battery is available ... 36 Resolving a low battery level when no power source is available ....
9 Memory modules .......................................................................................................................................... 54 10 Security ........................................................................................................................................................ 57 Protecting the computer ..................................................................................................................... 57 Using passwords ........................
Considering boot order changes ........................................................................................................ 72 Choosing MultiBoot preferences ........................................................................................................ 73 Setting a new boot order in Computer Setup ..................................................................... 73 Dynamically choosing a boot device using the f9 prompt ..................................................
x
1 Welcome After you set up and register the computer, take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, see Networking on page 14. ● Get to know your computer—Learn about your computer features. See Getting to know your computer on page 3 and Keyboard and pointing devices on page 19 for additional information. ● Find installed software—Access a list of the software preinstalled on the computer.
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about Setup Instructions poster ● Setting up the computer ● Identifying computer components Linux Help ● Computer software To access the Linux Help, select Computer > Help.
2 Getting to know your computer Top TouchPad NOTE: Your computer may look slightly different from the illustration in this section. Component Description (1) TouchPad on/off button Turns the TouchPad on and off. (2) TouchPad zone Moves the pointer and selects or activates items on the screen. (3) Left TouchPad button Functions like the left button on an external mouse. (4) Right TouchPad button Functions like the right button on an external mouse.
Lights NOTE: Your computer may look slightly different from the illustration in this section. Component (1) Power light ● On: The computer is on. ● Blinking: The computer is in the Suspend state. ● Off: The computer is off or in Hibernation. (2) Microphone mute light Amber: The microphone is off. (3) Num lock light On: Num lock is on. (4) Wireless light ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on.
Buttons and fingerprint reader (select models only) NOTE: Your computer may look slightly different from the illustration in this section. Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Suspend. ● When the computer is in the Suspend state, press the button briefly to exit Suspend. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component 6 Description (4) Volume mute button Mutes and restores speaker sound. (5) Fingerprint reader (select models only) Allows a fingerprint logon instead of a password logon.
Keys NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) fn key Executes frequently used system functions when pressed in combination with a function key. (2) Operating system logo key Displays the operating system menu. (3) Function keys Execute frequently used system functions when pressed in combination with the fn key. (4) Embedded numeric keypad keys When the keypad is turned on, it can be used like an external numeric keypad.
Component Description (1) fn key Executes frequently used system functions when pressed in combination with a function key. (2) Operating system logo key Displays the operating system menu. (3) Function keys Execute frequently used system functions when pressed in combination with the fn key. (4) num lk key Turns the embedded numeric keypad on and off when pressed in combination with the fn key. Alternates between the navigational and numeric functions on the integrated numeric keypad.
Component (1) (2) Description Hard drive light Media Card Reader ● Blinking white: The hard drive or optical drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. Reads data from and writes data to digital memory cards such as Secure Digital (SD).
Right Component (1) Description Audio-out (headphone) jack Produces sound when connected to optional powered stereo speakers, headphones, earbuds, a headset, or television audio. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety, and Environmental Notices. NOTE: When a device is connected to the jack, the computer speakers are disabled.
Component Description (1) Power connector Connects an AC adapter. (2) AC adapter light/battery light ● White: The computer is connected to external power and the battery is charged from 90 to 99 percent. ● Amber: The computer is connected to external power and the battery is charged from 0 to 89 percent or is charging. ● Blinking amber: A battery that is the only available power source has reached a low battery level.
Component Description (1) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) Internal microphone(s) (1 or 2 depending on model) Record sound. (3) Webcam light (select models only) On: The webcam is in use. (4) Webcam (select models only) Records video and captures still photographs. (5) Internal display switch Turns off the display or initiates Suspend if the display is closed while the power is on.
Bottom Component (1) Description Battery and service cover release latches ● Releases the battery from the battery bay by sliding the release latches one time. ● When the battery has been removed from the battery bay, releases the service cover from the computer by sliding the release latches a second time. (2) Battery bay Holds the battery. (3) Service cover Contains the hard drive, the wireless LAN (WLAN) module slot, and the memory module slots.
3 Networking Your computer may support one or both of the following types of Internet access: ● Wireless—For mobile Internet access, you can use a wireless connection. See Connecting to an existing WLAN on page 15 or Setting up a new WLAN on page 16. ● Wired—You can access the Internet by connecting to a wired network. For information on connecting to a wired network, see Connecting to a wired network on page 17.
NOTE: See Getting to know your computer on page 3 for information on identifying the type and location of the wireless button on your computer. Using the operating system controls To enable or disable a wireless or wired network device: 1. Right-click the Network Connection icon in the notification area, at the far right of the taskbar. 2.
Setting up a new WLAN Required equipment: ● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an Internet service provider (ISP) ● A wireless router (purchased separately) (2) ● The wireless computer (3) The illustration below shows an example of a wireless network installation that is connected to the Internet. NOTE: Some cable modems include a built-in router. Check with your ISP to see if you need a separate router.
NOTE: HP recommends that you select WPA2, which is the most advanced of the three encryption protocols. The use of WEP encryption is not recommended, because it can be overcome with little effort. ● ● Wi-Fi Protected Access (WPA) and Wi-Fi Protected Access II (WPA2) use security standards to encrypt and decrypt data transmitted over the network. Both WPA and WPA2 dynamically generate a new key for every packet, and they also generate a different set of keys for each computer on the network.
To connect the network cable: 1. Plug the network cable into the network jack (1) on the computer. 2. Plug the other end of the cable into a network wall jack (2) or a router (not illustrated). WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a modem or telephone cable into the RJ-45 (network) jack.
4 Keyboard and pointing devices Using the keyboard Identifying the hot keys A hot key is a combination of the fn key and one of the function keys. To use a hot key: ▲ Briefly press the fn key, and then briefly press the second key of the hot key combination. hot key combination fn+f3 Description Initiates Sleep, which saves your information in system memory. The display and other system components turn off and power is conserved. To exit Sleep, briefly press the power button.
The computer includes an embedded numeric keypad (or an integrated numeric keypad). The computer also supports an optional external numeric keypad or an optional external keyboard that includes a numeric keypad. Using the embedded numeric keypad (select models only) (1) Component Description fn key Turns the embedded numeric keypad on and off when pressed in combination with the num lk key.
Switching key functions on the embedded numeric keypad You can temporarily alternate the functions of keys on the embedded numeric keypad between their standard keyboard functions and their keypad functions: ● To use the navigational function of a keypad key while the keypad is off, press and hold the fn key while pressing the keypad key. ● To use the standard function of a keypad key while the keypad is on: ◦ Press and hold the fn key to type in lowercase.
Using the TouchPad To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go. Use the left and right TouchPad buttons like the buttons on an external mouse. NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased separately) by connecting it to one of the USB ports on the computer. Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off button.
Selecting Use the left and right TouchPad buttons like the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To view information about each gesture: 1. Select Computer > More Applications. 2. In the left pane, click System, and then click the TouchPad icon 3.
Tapping To make an on-screen selection, point to an item on the screen and then tap. ● Tap one finger on the TouchPad zone to make a selection. ● Double-tap an item to open it. NOTE: Press and hold on the TouchPad to open a help screen that provides information about the selected item. Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion.
Rotating Rotating allows you to turn items such as photos. ▲ Point to an object and then anchor the forefinger of your left hand in the TouchPad zone. Using your right hand, slide your forefinger in a sweeping motion from 12 o’clock to 3 o’clock. To reverse the rotation, move your forefinger from 3 o’clock to 12 o’clock. NOTE: Rotate is intended for specific apps where you can manipulate an object or image. It may not be functional for all apps.
5 Multimedia Your computer includes the following: ● Integrated speakers ● Integrated microphones ● Integrated webcam ● Preinstalled multimedia software ● Multimedia buttons or keys Using the audio features Your computer enables you to use a variety of audio features: ● Play music. ● Record sound. ● Download music from the Internet. ● Create multimedia presentations. ● Transmit sound and images with instant messaging programs. ● Stream radio programs.
Checking your audio functions To check the system sound on your computer, follow these steps: 1. Select Computer > Control Center. 2. In the left pane, click Hardware, and then click Sound in the right pane. 3. Click the Sound Effects tab, and then select one of the sound options under Choose an alert sound to test each sound. To check the recording functions of the computer, follow these steps: 1. Select Computer > Control Center. 2.
▲ To connect a VGA display device, connect the device cable to the external monitor port. Press fn+f4 to switch the image between the display devices connected to the computer. NOTE: Pressing fn+f4 allows you to switch between settings. You can toggle between a laptop panel, an external display in combination with the laptop panel, or one of the external monitors. You also can attach external monitors to both the DisplayPort and the VGA ports, but only one external display can be active at a time.
5. Your display settings can be modified by clicking your monitor in the dialog box, and then selecting the Display properties tab or Multi-Display tab. 6. After the settings are configured, click Apply, and then click OK. Your computer may require rebooting. HDMI The HDMI port connects the computer to an optional video or audio device, such as a high-definition television. NOTE: To transmit video and/or audio signals through the HDMI port, you need an HDMI cable (purchased separately).
6 Power management Shutting down the computer CAUTION: Unsaved information will be lost when the computer is shut down. The shutdown command closes all open programs, including the operating system, and then turns off the display and computer.
Initiating and exiting Suspend The system is set at the factory to initiate Suspend after a period of inactivity when running on battery power or on external power. Power settings and timeouts can be changed using Power Management in Control Center. With the computer on, you can initiate Suspend in any of the following ways: ● Briefly press the power button. ● Close the display. NOTE: This works only when the computer is running on battery power. ● Select Computer > Shutdown > Suspend.
You can customize power management settings. Viewing the current power management settings ▲ Right-click the Power icon in the notification area, at the far right of the taskbar, and then click Preferences. Changing the current power management settings 1. Right-click the Power icon in the notification area, at the far right of the taskbar, and then click Preferences. 2. Change the settings on the On AC Power tab, On Battery Power tab, and General tab, as needed.
▲ Insert the battery into the battery bay, aligning the tabs on the battery (1) with the notches on the computer, and then press the battery (2) down until it is seated. NOTE: The battery automatically locks into place. To remove the battery: CAUTION: Removing a battery that is the sole power source may cause loss of information. To prevent loss of information, save your work and initiate Hibernation or shut down the computer before removing the battery. 1.
The battery charges whenever the computer is plugged into external power through an AC adapter or an optional power adapter. The battery charges whether the computer is off or in use, but it charges faster when the computer is off. Charging may take longer if a battery is new, has been unused for 2 weeks or more, or is much warmer or cooler than room temperature.
Maximizing battery life To maximize battery life: 1. Select Computer > Control Center. 2. In the left pane, click System, and then click Power Management in the right pane. 3. On the On Battery Power tab: ● Adjust the slider to the right of Put computer to sleep when inactive for to 30 minutes. ● Select the Suspend or Hibernate option from the dialog box to the right of When laptop lid is closed.
Resolving a low battery level Resolving a low battery level when external power is available ▲ Connect the computer to external power using one of the following devices: ● AC adapter ● Optional docking or expansion device ● Optional power adapter purchased as an accessory from HP Resolving a low battery level when a charged battery is available 1. Turn off the computer or initiate Hibernation. 2. Replace the discharged battery with a charged battery. 3. Turn on the computer.
Disposing of a used battery WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water. See the Regulatory, Safety, and Environmental Notices for battery disposal information. Replacing the battery Computer battery life varies, depending on power management settings, programs running on the computer, display brightness, external devices connected to the computer, and other factors.
To test the AC adapter: 1. Shut down the computer. 2. Remove the battery from the computer. 3. Connect the AC adapter to the computer, and then plug it into an AC outlet. 4. Turn on the computer. ● If the power lights turn on, the AC adapter is functioning properly. ● If the power lights remain off, the AC adapter is not functioning and should be replaced. Contact technical support for information on obtaining a replacement AC power adapter.
7 Drives Handling drives CAUTION: Drives are fragile computer components that must be handled with care. See the following cautions before handling drives. Additional cautions are included with the procedures to which they apply. Observe these precautions: ● Before you move a computer that is connected to an external hard drive, initiate Suspend and allow the screen to clear, or properly disconnect the external hard drive.
To use the security screw: 1. Remove the battery (see Inserting or removing the battery on page 32). CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and shut down the computer through Windows before removing the battery. 2. Remove the security screw from inside the battery bay (1) and insert it (2) to lock the service door in place.
Removing the service door Remove the service door to access the memory module slot, hard drive, regulatory label, and other components. To remove the service door: 1. Remove the battery (see Inserting or removing the battery on page 32). 2. With the battery bay toward you, remove the screw (1) (if the optional screw is being used, see Using the optional security screw on page 39), and then slide the release latches (2) to release the service door.
3. With the battery bay toward you, slide the service door towards the battery bay until the service door snaps into place (4) and, if you choose to, insert and tighten the optional screw (5) to hold the service door in place (see Using the optional security screw on page 39). 4. Insert the battery (see Inserting or removing the battery on page 32).
Removing the hard drive To remove a hard drive: 1. Save your work. 2. Shut down the computer and close the display. 3. Disconnect all external hardware devices from the computer. 4. Unplug the power cord from the AC outlet. 5. Turn the computer upside down on a flat surface with the front of the computer toward you. 6. Remove the battery. (See Inserting or removing the battery on page 32.) 7. Remove the service door (see Removing or replacing the service door on page 40). 8.
10. Lift the hard drive (2) out of the hard drive bay.
Installing a hard drive To install a hard drive: 1. Angle the hard drive (1) into the hard drive bay, and then lower the hard drive (2) into the hard drive bay. 2. Pull the hard drive tab (3) to the right until the hard drive is connected to the system board.
3. Tighten the 4 screws to secure the hard drive. 4. Replace the service door (see Removing or replacing the service door on page 40). 5. Replace the battery (see Inserting or removing the battery on page 32). 6. Turn the computer right-side up, and then reconnect AC power and external devices to the computer. 7. Turn on the computer.
Inserting an optical disc Tray-load 1. Turn on the computer. 2. Press the eject button (1) on the drive bezel to release the disc tray. 3. Pull out the tray (2). 4. Hold the disc by the edges to avoid touching the flat surfaces and position the disc label-side up over the tray spindle. NOTE: If the tray is not fully accessible, tilt the disc carefully to position it over the spindle. 5. Gently press the disc (3) down onto the tray spindle until the disc snaps into place. 6. Close the disc tray.
2. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces. NOTE: If the tray is not fully accessible, tilt the disc carefully as you remove it. 3. Close the disc tray and place the disc in a protective case. When the disc tray fails to open 48 1. Insert the end of a paper clip (1) into the release access in the front bezel of the drive. 2.
3. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces. NOTE: If the tray is not fully accessible, tilt the disc carefully as you remove it. 4. Close the disc tray and place the disc in a protective case.
8 External cards and devices Using Media Card Reader cards (select models only) Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital cameras and PDAs as well as with other computers. To determine which digital card formats that are supported on your computer, see Getting to know your computer on page 3.
3. Press in on the card (1), and then remove it from the slot (2). NOTE: If the card is not ejected, pull the card out of the slot. Using a USB device Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Some USB devices may require additional support software, which is usually included with the device.
Connecting a USB device CAUTION: To prevent damage to a USB connector, use minimal force to connect a USB device. NOTE: The USB port on your computer may look slightly different from the illustration in this section. ▲ To connect a USB device to the computer, connect the USB cable for the device to the USB port. NOTE: When you connect a USB storage device, you may see a message in the notification area to let you know that the device is recognized by the system.
Using optional external devices NOTE: For more information about required software and drivers, or to learn which computer port to use, see the manufacturer's instructions. To connect an external device to the computer: CAUTION: To reduce the risk of damage to the equipment when connecting a powered device, be sure that the device is turned off and the AC power cord is unplugged. 1. Connect the device to the computer. 2.
9 Memory modules The computer has one memory module compartment. The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module. CAUTION: Electrostatic discharge (ESD) can damage electronic components.
b. Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot. To protect a memory module after removal, place it in an electrostatic-safe container. 7. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module, and do not bend the memory module. a. Align the notched edge (1) of the memory module with the tab in the memory module slot. b.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. 8. Replace the service door (see Removing or replacing the service door on page 40). 9. Replace the battery (see Inserting or removing the battery on page 32). 10. Turn the computer right-side up, and then reconnect AC power and external devices to the computer. 11. Turn on the computer.
10 Security Protecting the computer NOTE: Security solutions are designed to act as deterrents, but they may not deter software attacks or prevent the computer from being mishandled or stolen. Security features provided with your computer can protect the computer, personal information, and data from a variety of risks. The way you use your computer will determine which security features you need to use. The operating system offers certain security features.
Use the following tips for creating and saving passwords: ● When creating passwords, follow requirements set by the program. ● Write down your passwords and store them in a secure place away from the computer. ● Do not store passwords in a file on the computer. The following tables list commonly used passwords and describe their functions. Setting passwords in the operating system Operating system passwords Function Root password Protects access to an operating system root-level account.
Managing a BIOS administrator password To set, change, or delete this password, follow these steps: 1. Open Computer Setup by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the Startup Menu is displayed, press f10. 2. Use a pointing device or the arrow keys to select Security > Setup BIOS Administrator password, and then press enter. 3.
Managing a DriveLock password To set, change, or delete a DriveLock password in Computer Setup, follow these steps: 1. Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Use a pointing device or the arrow keys to select Security > DriveLock Password, and then press follow the on-screen instructions. 4.
There are two types of firewalls to consider: ● Host-based firewalls—Software that protects only the computer it is installed on. ● Network-based firewalls—Network based firewalls are installed between the computers on the network and the connection to the Internet. Network based firewalls can be dedicated devices or devices such as routers or switches with firewall capability.
Using the fingerprint reader (select models only) An integrated fingerprint reader is available on select computer models. In order to use the fingerprint reader, you must set up a user account with a password on the computer. This account allows you to log on to your computer with a swipe of a designated finger. Enabling fingerprint authentication during logon To enable fingerprint authentication during logon: 1. Select Computer > YaST. 2. Enter your root password, and then click Continue. 3.
11 Backup and Recovery Recovery after a system failure is as good as your most recent backup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. Your computer includes tools provided by HP to help you safeguard your information and retrieve it if ever needed. Creating backups 1. Create restore media immediately after you set up the computer. For more information, see Performing a system recovery on page 64. 2.
5. Under Restore Point, click the time and date of the backup. NOTE: If multiple backups have been performed, click Use the latest version to restore the latest version. 6. Click Restore to start restoring the files, or click Cancel to cancel the operation. Performing a system recovery Recovery allows you to repair or restore the computer to its original factory state. You can create an HP Factory Image Restore DVD, using an installed or an external DVD±RW optical drive.
Creating a USB Recovery Disk On Key 1. Connect the USB Disk On Key to a USB port on the computer. 2. Select Computer > More applications > Tools > Create Recovery USB. 3. Enter the root password when prompted. 4. Select USB Disk On Key from the list. 5. Click OK. 6. A question dialog will remind you that the data on the USB key will be destroyed. To continue, click OK. Otherwise, click Cancel and back up the contents of the Disk On Key on another computer. 7.
IMPORTANT: This option does not provide backups of your information. Before using this option, back up any personal information you wish to retain. You can initiate this option by using the f11 key. To use the f11 key: Press f11 while the computer boots. – or – Press and hold f11 as you press the power button. The following options are available: ● Cancel/Reboot—Reboots the system. No recovery or restore activity is performed.
12 Computer Setup (BIOS) and Advanced System Diagnostics Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of peripherals installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter. – or – ● To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions.
BIOS version information (also known as ROM date and System BIOS) can be displayed as follows: 1. Start Computer Setup. 2. Use a pointing device or the arrow keys to select File > System Information. 3. To exit Computer Setup without saving your changes, click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter.
Using Advanced System Diagnostics Advanced System Diagnostics allows you to run diagnostic tests to determine if the computer hardware is functioning properly. The following diagnostic tests are available in Advanced System Diagnostics: ● Start-up test—This test analyzes the main computer components that are required to start the computer. ● Run-in test—This test repeats the start-up test and checks for intermittent problems that the start-up test does not detect.
13 MultiBoot About the boot device order As the computer starts, the system attempts to boot from enabled boot devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly.
Enabling boot devices in Computer Setup The computer will boot to a USB device or a NIC device only if the device has first been enabled in Computer Setup. To start Computer Setup and enable a USB device or a NIC device as a boot device, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3.
● The computer will boot from a NIC device only if the device has been enabled in the Built-In Device Options menu of Computer Setup and if booting from the device has been enabled in the Boot Options menu of Computer Setup. Booting from a NIC does not affect logical drive designations because no drive letter is associated with the NIC. ● Drives in an optional docking device are treated like external USB devices in the boot order.
Dynamically choosing a boot device using the f9 prompt To dynamically choose a boot device for the current startup sequence, follow these steps: 1. Open the Select Boot Device menu by turning on or restarting the computer, and then pressing esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f9. 3. Use a pointing device or the arrow keys to select a boot device, and then press enter. Your changes go into effect immediately.
A Troubleshooting and support Troubleshooting The following sections describe several common issues and solutions. The computer is unable to start up If the computer does not turn on when you press the power button, the following suggestions may help you determine why the computer does not start up: ● If the computer is plugged into an AC outlet, plug another electrical device into the outlet to be sure that the outlet is providing adequate power.
CAUTION: Emergency shutdown procedures result in the loss of unsaved information. ● Press and hold the power button for at least 5 seconds. ● Disconnect the computer from external power and remove the battery. The computer is unusually warm It is normal for the computer to feel warm to the touch while it is in use. But if the computer feels unusually warm, it may be overheating because a vent is blocked. If you suspect that the computer is overheating, allow the computer to cool to room temperature.
The optical disc tray does not open for removal of a CD or DVD 1. Insert the end of a paper clip (1) into the release access in the front bezel of the drive. 2. Press in gently on the paper clip until the disc tray is released, and then pull out the tray (2) until it stops. 3. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
The computer does not detect the optical drive If your operating system does not detect an installed device, the device driver software may be missing or corrupted. 1. Remove any discs from the optical drive. 2. Click Computer and then click System Monitor. 3. On the Hardware tab, identify the Storage Controller in the Type column. 4. Click the triangle next to the devices until you locate your optical drive. If the drive is listed, it should be functioning correctly.
The process of burning a disc does not begin, or it stops before completion ● Be sure that all other programs are closed. ● Turn off Suspend mode and Hibernation. ● Be sure that you are using the right kind of disc for your drive. ● Be sure that the disc is inserted properly. ● Select a slower write speed and try again. ● If you are copying a disc, save the information on the source disc to your hard drive before trying to burn the contents to a new disc, and then burn from your hard drive.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support. The serial number label is affixed inside the battery bay.
B Cleaning your computer Cleaning products Use the following products to safely clean and disinfect your computer: ● Dimethyl benzyl ammonium chloride 0.3 percent maximum concentration (For example: germicidal disposable wipes. These wipes come in a variety of brand names.
Cleaning the TouchPad and keyboard CAUTION: When cleaning the TouchPad and keyboard, do not let liquids drip between the keys. This can permanently damage internal components. ● To clean and disinfect the TouchPad and keyboard, use a soft microfiber cloth or chamois moistened with one of the cleaning solutions listed previously or use an acceptable germicidal disposable wipe.
C Specifications Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
D Electrostatic discharge Electrostatic discharge is the release of static electricity when two objects come into contact—for example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.
Index A AC adapter light, identifying 11 action keys volume 26 airport security devices 39 audio features 26 audio functions, checking 27 audio-in (microphone) jack, identifying 10 audio-out (headphone) jack, identifying 10 B backup 63 battery charging 33 conserving power 36 disposing 37 inserting 32 life 35 low battery levels 35 power 32 removing 32 storing 36 temperature 36 battery bay 13 battery release latches 13, 32 BIOS determining version 68 downloading an update 69 updating 68 BIOS administrator pas
initiated during critical battery level 35 initiating 31 high-definition devices, connecting 29 hot keys adjusting volume 19 decrease screen brightness 19 description 19 increase screen brightness 19 microphone mute 19 switching screen image 19 using 19 hubs 51 I icons network 14 wired network 14 wireless 14 input power 83 integrated numeric keypad, identifying 8, 21 integrated webcam light, identifying 12 internal display switch 12 internal microphones, identifying 12 Internet connection setup 16 issues, r
power connector, identifying 11 power lights 4 power, conserving 36 product name and number, computer 80 public WLAN connection 15 PXE server 72 R readable media 30 recovery 63 regulatory information regulatory label 80 wireless certification labels reset computer 65 steps 65 RJ-45 (network) jack 11 RJ-45 (network) lights 11 80 S screen brightness keys 19 screen image, switching 19 scrolling TouchPad gesture 24 security cable 61 security cable slot, identifying 10 security screw, using 39 security, wirele
