HP ProLiant BL460c Gen9 Server Blade User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers and storage systems. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.
© Copyright 2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation.
Contents Component identification ............................................................................................................... 6 Front panel components ................................................................................................................................ 6 Front panel LEDs and buttons ......................................................................................................................... 6 Power fault LEDs.........................................
Memory configurations ..................................................................................................................... 34 General DIMM slot population guidelines ........................................................................................... 35 Installing a DIMM............................................................................................................................. 36 Processor option........................................................................
HP operating systems and virtualization software support for ProLiant servers ......................................... 62 HP Technology Service Portfolio ......................................................................................................... 63 Change control and proactive notification .......................................................................................... 63 Battery replacement ...........................................................................................
Component identification Front panel components Item Description 1 Hard drive bay 1 2 Server blade release button 3 Server blade release lever 4 Hard drive bay 2 5 HP c-Class Blade SUV connector* (behind the serial label pull tab) 6 Serial label pull tab *The SUV connector and the HP c-Class Blade SUV Cable are used for some server blade configuration and diagnostic procedures.
Item Description 3 Status button and system power LED* Flashing green (1 Hz/cycle per sec) = Performing power on sequence Solid amber = System in standby Off = No power present** UID button/LED* Solid blue = Activated Flashing blue: • • • 1 Hz/cycle per sec = Remote management or firmware upgrade in progress 4 Hz/cycle per sec = iLO manual reboot sequence initiated 8 Hz/cycle per sec = iLO manual reboot sequence in progress Off = Deactivated 4 NIC activity LED* Solid green = Link to network Flash
Item Description 2 Drive bay 2 Hot-plug drive LED definitions Item LED Status Definition 1 Locate Solid blue The drive is being identified by a host application. Flashing blue The drive carrier firmware is being updated or requires an update. Rotating green Drive activity Off No drive activity Solid white Do not remove the drive. Removing the drive causes one or more of the logical drives to fail. Off Removing the drive does not cause a logical drive to fail.
System board components Item Description 1 System battery 2 Solid state device connector 3 Processor 2 DIMM slots (8) 4 Processor 1 DIMM slots (8) 5 SAS controller connector 6 Mezzanine connector 1 (Type A mezzanine only) 7 Mezzanine connector 2 (Type A or Type B mezzanine) 8 Enclosure connector 9 MicroSD card slot 10 FlexibleLOM connectors (2) 11 Drive backplane 12 Internal USB connector 13 HP Smart Storage Battery connector 14 Direct-connect SATA connector 15 System mainten
Position Default Function S3 Off Reserved S4 Off Reserved S5 Off Off = Power-on password is enabled. On = Power-on password is disabled. S6 Off Off = No function. On = ROM reads system configuration as invalid. S7 Off Off = Set default boot mode to UEFI. On = Set default boot mode to legacy. S8 — Reserved S9 — Reserved S10 — Reserved S11 — Reserved S12 — Reserved To access the redundant ROM, set S1, S5, and S6 to on.
SUV cable connectors CAUTION: Before disconnecting the SUV cable from the connector, always squeeze the release buttons on the sides of the connector. Failure to do so can result in damage to the equipment.
Operations Power up the server blade The Onboard Administrator initiates an automatic power-up sequence when the server blade is installed. If the default setting is changed, use one of the following methods to power up the server blade: • Use a virtual power button selection through HP iLO. • Press and release the Power On/Standby button. When the server blade goes from the standby mode to the full power mode, the system power LED changes from amber to solid green.
o poweroff server [bay number] force This form of the command forces the server blade to enter standby mode without properly exiting applications and the OS. If an application stops responding, this method forces a shutdown. • Use the Onboard Administrator GUI to initiate a shutdown: a. Select the Enclosure Information tab. b. In the Device Bays item, select the Overall checkbox. c.
Remove the access panel To remove the component: 1. Power down the server blade (on page 12). 2. Remove the server blade (on page 13). 3. Place the server blade on a flat, level work surface. 4. Press the access panel release button. 5. Slide the access panel towards the rear of the server blade, and then lift to remove the panel. Remove the DIMM baffle 1. Power down the server blade (on page 12). 2. Remove the server blade (on page 13). 3.
o DIMM baffle (right side) o DIMM baffle (left side) Remove the storage controller 1. Power down the server blade (on page 12). 2. Remove the server blade (on page 13).
3. Place the server blade on a flat, level work surface. 4. Remove the access panel (on page 14). 5. Prepare the storage controller for removal. 6. Remove the storage controller. Remove the front panel/hard drive cage assembly 1. Power down the server blade (on page 12). 2. Remove the server blade (on page 13). 3. Place the server blade on a flat, level work surface. 4. Remove the access panel (on page 14). 5.
6. Remove the internal USB drive, if installed. To locate the internal USB connector, see "System board components (on page 9)." 7. Remove all DIMM baffles ("Remove the DIMM baffle" on page 14). 8. Remove the storage controller (on page 15). CAUTION: Always remove the SAS controller before removing the front panel/drive cage assembly. 9. Extend the serial label pull tab from the front of the server blade. 10. Remove the two T-15 screws from the front panel/drive cage assembly. 11.
5. Remove the mezzanine assembly. Remove the FlexibleLOM 1. Power down the server blade (on page 12). 2. Remove the server blade (on page 13). 3. Place the server blade on a flat, level work surface. 4. Remove the access panel (on page 14). 5. Remove the mezzanine assembly (on page 17). 6. Use the FlexibleLOM handle to remove the FlexibleLOM from the system board. Install the storage controller 1. Power down the server blade (on page 12).
2. Remove the server blade (on page 13). 3. Place the server blade on a flat, level work surface. 4. Remove the access panel (on page 14). 5. Prepare the storage controller for installation. 6. Align the storage controller with the alignment pins and lower it into server blade. 7. Push the handle down into the closed position to fully seat the storage controller. Install the access panel 1. Place the access panel on top of the server blade. 2.
Setup Overview Installation of a server blade requires the following steps: 1. Install and configure an HP BladeSystem c-Class enclosure. 2. Install any server blade options. 3. Install interconnect modules in the enclosure. 4. Connect the interconnect modules to the network. 5. Install a server blade. 6. Complete the server blade configuration. Installing an HP BladeSystem c-Class enclosure Before performing any server blade-specific procedures, install an HP BladeSystem c-Class enclosure.
Installing interconnect modules For specific steps to install interconnect modules, see the documentation that ships with the interconnect module. Interconnect bay numbering and device mapping • HP BladeSystem c7000 Enclosure To support network connections for specific signals, install an interconnect module in the bay corresponding to the FlexibleLOM or mezzanine signals.
• HP BladeSystem c3000 Enclosure and Tower Enclosure Notes Server blade signal Interconnect bay number FlexibleLOM 1 — Mezzanine 1 2 Four port cards connect to bay 2. Mezzanine 2 3 and 4 • • • Interconnect bay label Four port cards Ports 1 and 3 connect to bay 3. Ports 2 and 4 connect to bay 4.
Two types of interconnect modules are available for HP BladeSystem c-Class enclosures: Pass-Thru modules and switch modules. For more information about interconnect module options, see the HP website (http://www.hp.com/go/bladesystem/interconnects). IMPORTANT: To connect to a network with a Pass-Thru module, always connect the Pass-Thru module to a network device that supports Gigabit or 10 Gb speed, depending on the corresponding Pass-Thru model.
2. Remove the enclosure connector cover. 3. Install the server blade. Completing the configuration To complete the server blade and HP BladeSystem configuration, see the overview card that ships with the enclosure.
Hardware options installation Introduction If more than one option is being installed, read the installation instructions for all the hardware options and identify similar steps to streamline the installation process. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly ground the server before beginning any installation procedure.
2. Prepare the drive. 3. Install the drive. 4. Determine the status of the drive from the drive LED definitions ("Hot-plug drive LED definitions" on page 8). Storage controller option To install the component: 1. Back up all server blade data. 2. Power down the server blade (on page 12). 3. Remove the server blade (on page 13). 4. Place the server blade on a flat, level work surface. 5. Remove the access panel (on page 14).
6. Prepare the storage controller for installation. 7. Align the storage controller with the alignment pins and lower it into server blade. 8. Push the handle down into the closed position to fully seat the storage controller. 9. Install the access panel (on page 19). 10. Install the server blade ("Installing a server blade" on page 23). 11. Power up the server blade (on page 12). HP Smart Storage Battery option To install the component: 1. Power down the server blade (on page 12). 2.
4. Remove the access panel (on page 14). 5. Disconnect the direct connect SATA cable, if installed ("Installing the direct connect SATA cable" on page 47). 6. Remove the internal USB drive, if installed. To locate the internal USB connector, see "System board components (on page 9)." 7. Remove the right DIMM baffle ("Remove the DIMM baffle" on page 14). 8. Install the HP Smart Storage Battery on the DIMM baffle. 9. Route the cable on the DIMM baffle. 10. Align and install the DIMM baffle.
11. Press down on the cable connector to fully seat the HP Smart Storage Battery cable connector to the system board. 12. Route and connect the direct connect SATA cable, if installed ("Installing the direct connect SATA cable" on page 47). 13. Install the access panel (on page 19). 14. Install the server blade ("Installing a server blade" on page 23). 15. Power up the server blade (on page 12).
5. Remove the mezzanine assembly. 6. Align the mezzanine card with the guide pins on the mezzanine assembly.
7. Install the mezzanine card in the mezzanine assembly, and then tighten the mezzanine card screws to secure the card to the mezzanine assembly. 8. Align the mezzanine assembly with the guide pins on the system board, and then install the mezzanine assembly on the system board. 9. Press down firmly on the mezzanine assembly handles, and then close the mezzanine assembly latch. 10. Install the access panel (on page 19). 11. Install the server blade ("Installing a server blade" on page 23). 12.
The memory subsystem in this server blade can support LRDIMMs and RDIMMs: • RDIMMs offer address parity protection. • LRDIMMs support higher densities than single- and dual-rank RDIMMs, and higher speeds than quad-rank RDIMMs. This support enables you to install more high capacity DIMMs, resulting in higher system capacities and higher bandwidth. All types are referred to as DIMMs when the information applies to all types. When specified as LRDIMM or RDIMM, the information applies to that type only.
Channel Slot Slot number 4 D H 6 5 For the location of the slot numbers, see "DIMM slot locations (on page 10)." This multi-channel architecture provides enhanced performance in Advanced ECC mode. DIMM slots in this server blade are identified by number and by letter. Letters identify the population order. Slot numbers indicate the DIMM slot ID for spare replacement.
Item Description Definition 2 Rank 1R = Single-rank 2R = Dual-rank 4R = Quad-rank 3 Data width x4 = 4-bit x8 = 8-bit 4 Memory generation DDR4 5 2133 MT/s 6 Maximum memory speed CAS latency 7 DIMM type R = RDIMM (registered) L = LRDIMM (load reduced) 32 GB P=15 For more information about product features, specifications, options, configurations, and compatibility, see the product QuickSpecs on the HP website (http://www.hp.com/go/qs).
Advanced ECC protects the server blade against some multi-bit memory errors. Advanced ECC can correct both single-bit memory errors and 4-bit memory errors if all failed bits are on the same DRAM device on the DIMM. Advanced ECC provides additional protection over Standard ECC because it is possible to correct certain memory errors that would otherwise be uncorrected and result in a server blade failure.
Online spare population guidelines For Online Spare memory mode configurations, observe the following guidelines: • Observe the general DIMM slot population guidelines (on page 35). • Each channel must have a valid online spare configuration. • Each channel can have a different valid online spare configuration. • Each populated channel must have a spare rank. A single dual-rank DIMM is not a valid configuration.
10. Install the DIMM. 11. Route and connect the direct connect SATA cable, if installed ("Installing the direct connect SATA cable" on page 47). 12. Install all DIMM baffles. 13. Install the FlexibleLOM. 14. Install the mezzanine assembly. 15. Install the access panel (on page 19). 16. Install the server blade ("Installing a server blade" on page 23). 17. Power up the server blade (on page 12). To configure the memory mode, use HP UEFI System Utilities (on page 57).
To install a processor: 1. Update the system ROM. Locate and download the latest ROM version from the HP website (http://www.hp.com/support). Follow the instructions on the website to update the system ROM. 2. Power down the server blade (on page 12). 3. Remove the server blade (on page 13). 4. Place the server blade on a flat, level work surface. 5. Remove the access panel (on page 14). 6. Remove the storage controller (on page 15). 7. Access the processor socket.
9. Open each of the processor locking levers in the order indicated in the following illustration, and then open the processor retaining bracket. 10. Remove the clear processor socket cover. Retain the processor socket cover for future use. CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To avoid damage to the system board, do not touch the processor or the processor socket contacts.
11. Install the processor. Verify that the processor is fully seated in the processor retaining bracket by visually inspecting the processor installation guides on either side of the processor. THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. 12. Close the processor retaining bracket. When the processor is installed properly inside the processor retaining bracket, the processor retaining bracket clears the flange on the front of the socket. CAUTION: Do not press down on the processor.
13. Press and hold the processor retaining bracket in place, and then close each processor locking lever. Press only in the area indicated on the processor retaining bracket. 14. Remove the thermal interface protective cover from the heatsink. CAUTION: To avoid damage to the system board, processor socket, and screws, do not overtighten the heatsink screws.
15. Using a T-15 screwdriver, install the heatsink. 16. Install the storage controller (on page 18). 17. Install the access panel (on page 19). 18. Install the server blade ("Installing a server blade" on page 23). 19. Power up the server blade (on page 12). HP Trusted Platform Module option For more information about product features, specifications, options, configurations, and compatibility, see the product QuickSpecs on the HP website (http://www.hp.com/go/qs).
• When returning a system board for service replacement, do not remove the TPM from the system board. When requested, HP Service provides a TPM with the spare system board. • Any attempt to remove an installed TPM from the system board breaks or disfigures the TPM security rivet. Upon locating a broken or disfigured rivet on an installed TPM, administrators should consider the system compromised and take appropriate measures to ensure the integrity of the system data.
11. Install the TPM board. Press down on the connector to seat the board ("System board components" on page 9). 12. Install the TPM security rivet by pressing the rivet firmly into the system board. 13. Install the front panel/drive cage assembly. 14. Install the storage controller (on page 18). 15. Install the DIMM baffle. 16. Route and connect the direct connect SATA cable, if installed ("Installing the direct connect SATA cable" on page 47). 17. Install the USB drive, if removed. 18.
Retaining the recovery key/password The recovery key/password is generated during BitLocker setup, and can be saved and printed after BitLocker is enabled. When using BitLocker, always retain the recovery key/password. The recovery key/password is required to enter Recovery Mode after BitLocker detects a possible compromise of system integrity.
Cabling Cabling resources Cabling configurations and requirements vary depending on the product and installed options. For more information about product features, specifications, options, configurations, and compatibility, see the product QuickSpecs on the HP website (http://www.hp.com/go/qs).
Installing the direct connect SATA cable Using the HP c-Class Blade SUV Cable The HP c-Class Blade SUV Cable enables the user to perform server blade administration, configuration, and diagnostic procedures by connecting video and USB devices directly to the server blade. For SUV cable connectors, see "SUV cable connectors (on page 11).
3. Connect a USB mouse to one USB connector. 4. Connect a USB keyboard to the second USB connector. Item Description 1 Monitor 2 USB mouse 3 USB keyboard 4 HP c-Class Blade SUV Cable Accessing local media devices Use the following configuration when configuring a server blade or loading software updates and patches from a USB CD/DVD-ROM. Use a USB hub when connecting a USB CD-ROM drive to the server blade. The USB hub provides additional connections. 1.
o USB mouse Item Description 1 Monitor 2 USB CD/DVD-ROM drive 3 USB keyboard 4 USB hub 5 USB mouse 6 HP c-Class Blade SUV Cable Cabling 49
Troubleshooting Troubleshooting resources The HP ProLiant Gen9 Troubleshooting Guide, Volume I: Troubleshooting provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, issue resolution, and software maintenance on ProLiant servers and server blades. To view the guide, select a language: • English (http://www.hp.com/support/Gen9_TSG_en) • French (http://www.hp.com/support/Gen9_TSG_fr) • Spanish (http://www.hp.
Software and configuration utilities Server mode The software and configuration utilities presented in this section operate in online mode, offline mode, or in both modes.
Using HP iLO, you can do the following: • Access a high-performance and secure Integrated Remote Console to the server from anywhere in the world if you have a network connection to the server. • Use the shared .NET Integrated Remote Console to collaborate with up to four server administrators. • Remotely mount high-performance Virtual Media devices to the server blade. • Securely and remotely control the power state of the managed server blade.
HP Active Health System does not collect information about Active Health System users' operations, finances, customers, employees, partners, or data center, such as IP addresses, host names, user names, and passwords. HP Active Health System does not parse or change operating system data from third-party error event log activities, such as content created or passed through by the operating system. The data that is collected is managed according to the HP Data Privacy policy.
HP Insight Remote Support HP strongly recommends that you register your device for remote support to enable enhanced delivery of your HP Warranty, HP Care Pack Service, or HP contractual support agreement.
Intelligent Provisioning Intelligent Provisioning is a single-server deployment tool embedded in HP ProLiant Gen8 and later servers that simplifies HP ProLiant server setup, providing a reliable and consistent way to deploy HP ProLiant server configurations: • Intelligent Provisioning assists with the OS installation process by preparing the system for installing "off-the-shelf" and HP branded versions of operating system software and integrating optimized HP ProLiant server support software.
CAUTION: Perform a backup before running the Erase Utility. The utility sets the system to its original factory state, deletes the current hardware configuration information, including array setup and disk partitioning, and erases all connected hard drives completely. Before using this utility, see the instructions in the HP Intelligent Provisioning User Guide. Use the Erase Utility to erase drives and Active Health System logs, and to reset UEFI System Utilities settings.
For more information about HP SUM, see the product page on the HP website (http://www.hp.com/go/hpsum). To download HP SUM, see the HP website (http://www.hp.com/go/hpsum/download). To access the HP Smart Update Manager User Guide, see the HP SUM Information Library (http://www.hp.com/go/hpsum/documentation). HP UEFI System Utilities The HP UEFI System Utilities is embedded in the system ROM.
Flexible boot control This feature enables you to do the following: • Add Boot Options o Browse all FAT16 and FAT32 file systems. o Select an X64 UEFI application with an .EFI extension to add as a new UEFI boot option, such as an OS boot loader or other UEFI application. The new boot option is appended to the boot order list. When you select a file, you are prompted to enter the boot option description (which is then displayed in the Boot menu), as well as any optional data to be passed to an .
more information about supported operating systems, see the HP UEFI System Utilities and Shell Release Notes on the HP website (http://www.hp.com/go/ProLiantUEFI/docs). A physically present user can customize the certificates embedded in the UEFI BIOS by adding/removing their own certificates. Embedded UEFI shell The system BIOS in all HP ProLiant Gen9 servers includes an embedded UEFI Shell in the ROM.
Warning: The Product ID should ONLY be modified by qualified service personnel. This value should always match the Product ID located on the chassis. 7. Enter the product ID and press the Enter key. 8. Press the F10 key to confirm exiting System Utilities. The server blade automatically reboots. Utilities and features HP Smart Storage Administrator HP SSA is a configuration and management tool for HP Smart Array controllers.
USB support HP provides standard USB 2.0 support, standard USB 3.0 support, and legacy USB support. Standard support is provided by the OS through the appropriate USB device drivers. Before the OS loads, HP provides support for USB 2.0 devices through legacy USB support, which is enabled by default in the system ROM. USB 3.0 ports are not functional before the OS loads. The native OS provides USB 3.0 support through appropriate xHCI drivers.
The server blade includes new hardware that may not have driver support on all OS installation media. If you are installing an Intelligent Provisioning-supported OS, use Intelligent Provisioning (on page 55) and its Configure and Install feature to install the OS and latest supported drivers. If you do not use Intelligent Provisioning to install an OS, drivers for some of the new hardware are required.
HP Technology Service Portfolio Connect to HP for assistance on the journey to the new style of IT. HP Technology Services delivers confidence and reduces risk to help you realize agility and stability in your IT infrastructure. Utilize our consulting expertise in the areas of private or hybrid cloud computing, big data and mobility requirements, improving data center infrastructure and better use of today’s server, storage and networking technology. For more information, see the HP website (http://www.hp.
Battery replacement If the server blade no longer automatically displays the correct date and time, then replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • • • • Do not attempt to recharge the battery.
Regulatory information Safety and regulatory compliance For safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products, available at the HP website (http://www.hp.com/support/Safety-Compliance-EnterpriseProducts). Belarus Kazakhstan Russia marking Manufacturer Hewlett-Packard Company, Address: 3000 Hanover Street, Palo Alto, California 94304, U.S.
Valid date formats include the following: • YWW, where Y indicates the year counting from within each new decade, with 2000 as the starting point. For example, 238: 2 for 2002 and 38 for the week of September 9. In addition, 2010 is indicated by 0, 2011 by 1, 2012 by 2, 2013 by 3, and so forth. • YYWW, where YY indicates the year, using a base year of 2000. For example, 0238: 02 for 2002 and 38 for the week of September 9.
Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage: • Avoid hand contact by transporting and storing products in static-safe containers.
Specifications Environmental specifications Specification Value — Temperature range* Operating 10°C to 35°C (50°F to 95°F) Non-operating -30°C to 60°C (-22°F to 140°F) Relative humidity (noncondensing)** — Operating 10% to 90% @ 28°C (82.4°F) Non-operating 5% to 95% @ 38.7°C (101.7°F) Altitude† — Operating 3050 m (10,000 ft) Non-operating 9144 m (30,000 ft) * The following temperature conditions and limitations apply: - All temperature ratings shown are for sea level.
Support and other resources Before you contact HP Be sure to have the following information available before you call HP: • Active Health System log (HP ProLiant Gen8 or later products) Download and have available an Active Health System log for 7 days before the failure was detected. For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP website (http://www.hp.com/go/ilo/docs).
providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts: • Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service. • Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP (http://www.hp.com/go/selfrepair). Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair).
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet. CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen einen Aufpreis verfügbar.
sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio. Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica, visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto. OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça.
Support and other resources 75
Support and other resources 76
Acronyms and abbreviations ACU Array Configuration Utility AMP Advanced Memory Protection API application program interface ASR Automatic Server Recovery CSR certificate signing request HP SSA HP Smart Storage Administrator HP SUM HP Smart Update Manager iLO Integrated Lights-Out IML Integrated Management Log JSON JavaScript Object Notation KVM keyboard, video, and mouse PCIe Peripheral Component Interconnect Express Acronyms and abbreviations 77
POST Power-On Self Test RBSU ROM-Based Setup Utility REST representational state transfer SAS serial attached SCSI SPP HP Service Pack for ProLiant SUV serial, USB, video TPM Trusted Platform Module UEFI Unified Extensible Firmware Interface USB universal serial bus VCA Version Control Agent VCRM Version Control Repository Manager Acronyms and abbreviations 78
Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback.
Index A access panel 19 ACU (Array Configuration Utility) 60 Advanced ECC memory 34, 35 array controllers 18, 26 ASR (Automatic Server Recovery) 60 authorized reseller 69 Automatic Server Recovery (ASR) 60 B Basic Input/Output System (BIOS) 51, 60 batteries, replacing 64 battery 9, 27, 46, 64 battery replacement notice 65 before you contact HP 69 BIOS (Basic Input/Output System) 51, 60 BIOS upgrade 51, 60 blade blank 20, 23 BSMI notice 65 buttons 6 C cables 46, 47, 48 cabling 11, 46, 47 Canadian notice 65
front panel components 6 front panel LEDs 6 front panel/drive cage assembly 16 internal USB connector 9 G Japanese notice 65 grounding methods 67 L H LED, health 6 LED, power button 6 LED, system power 6 LEDs 8 LEDs, hard drive 8 LEDs, NIC 6 LEDs, SAS hard drive 8 LEDs, troubleshooting 50 LEDs, unit identification (UID) 6 local KVM, accessing a server blade with 47 local media devices, accessing 48 hard drive backplane connector 9 hard drive bays 6 hard drive LEDs 8 hard drives, determining status o
QuickSpecs 33, 46, 51 specifications 68 specifications, environmental 68 specifications, server blade 68 SPP 56 static electricity 67 storage controller 18, 26 support 69 supported operating systems 62 SUV connector 6, 11, 47, 48 switches, interconnect 21 system board battery 9, 64 system components 6 system configuration settings 61 System Erase Utility 55 system maintenance switch 9 system power LED 6 system, keeping current 61 R T recovery key 45 redundant ROM 61 regulatory compliance identification
