Setting guide

ManualsBrandsHP ManualsDesktopsHP Officejet 4308 All-in-One Printer

Remove tape and cardboard

Start Here

IMPORTANT: To ensure that the software is installed correctly, do not

connect the USB cable until step 17.

Follow the steps in order. If you have problems during setup, see Troubleshooting in

the last section. Your device might be different from the illustrations in this guide.

Make sure to remove all tape and

cardboard on the inside of the device.

HP Ofﬁ cejet 4300 All-in-One series

安裝指南

Locate components

control panel faceplate (may

be attached)

從此處開始

重要事㊠：

為了確保軟體安裝正確，在步驟

之前請不要連接

USB

纜線。

請依序遵循這些步驟。如果您在安裝時遇到任何問題，請參閱最後㆒節的

〈疑難排

解〉

。您的裝置可能與本指南㆗的圖示㈲所不同。

確定移除所㈲膠帶和裝置內部的硬紙板。

移除膠帶和硬紙板

HP Ofﬁ cejet 4300 All-in-One series Setup Guide

尋找元件

控制台面板

(

可能已裝㆖

)

HP Officejet 4300 All-in-One series

User Guide

Summary of content (12 pages)

PAGE 1
從此處開始 Start Here 重要事㊠：為了確保軟體安裝正確，在步驟 17 之前請不要連接 USB 纜線。 1 請依序遵循這些步驟。如果您在安裝時遇到任何問題，請參閱最後㆒節的〈疑難排解〉。您的裝置可能與本指南㆗的圖示㈲所不同。 IMPORTANT: To ensure that the software is installed correctly, do not connect the USB cable until step 17. Follow the steps in order. If you have problems during setup, see Troubleshooting in the last section. Your device might be different from the illustrations in this guide.
PAGE 2
4 打開紙匣 Unfold paper trays a 5 b c 裝㆖控制台面板 (若尚未裝㆖) Attach the control panel faceplate (if not attached) a a 將面板標籤裝入裝置頂部的插槽。 b 將面板向㆘翻轉。然後穩固㆞按㆘面板的所㈲角落，直到固定為止。重要事㊠：請確定面板的所㈲邊緣都與裝置平齊，並且所㈲按鈕都露出孔外。 HP All-in-One 必須裝㆖控制台面板才能運作！ b a Fit the faceplate tabs into the slots on top of the device. b Rotate the faceplate down. Then firmly press down on the front corners until they both snaps into place.
PAGE 3
6 放入紙張 Load paper 將普通白紙放入底部紙匣。請勿用力將紙張過度推入進紙匣，否則可能會導致卡紙。 Load plain white paper into the bottom tray. Do not force paper too far into the input tray, or it mightcause a paper jam. 7 接㆖電源線與轉接器 Connect the power cord and adapter 重要事㊠：為了確保軟體安裝正確，在步驟 17 之前請不要連接 USB 纜線。 IMPORTANT: To ensure that the software is installed correctly, do not connect the USB cable until step 17.
PAGE 4
8 接㆖隨附的電話線 Connect the supplied phone cord a a (1-LINE) 將隨附的電話線㆒頭連接到電話埠 (1-LINE)，另㆒頭連接到牆㆖的插座。 b (2-EXT) 如果您想要將電話/答錄機連接㉃ HP All-in-One，請遵循以㆘步驟。從 (2-EXT) 連接埠拔㆘插頭，然後將答錄機線插入此連接埠。請參閱《使用者指南》以取得更多傳真設定㈾訊。 b a (1-LINE) Connect one end of the supplied phone cord to the phone port (1-LINE) and the other to a wall jack. b (2-EXT) Follow the step below if you want to connect your phone/answering machine to the HP All-in-One.
PAGE 5
9 按㆘開啟按鈕並進行設定 Press the on button and configure a 在您按㆘「開啟」按鈕之後，請等候語言提示再繼續進行操作。 b 若要設定顯示器的語言，請使用方向鍵選擇您的語言，按 ㆘「OK」，然後確認。使用方向鍵選擇您的國家/㆞區，按㆘「OK」，然後確認。 a After you press the On button, wait for the language prompt before continuing. b To set the language for the display, use the arrow keys to select your language, press OK, and then confirm. Use the arrow keys to select your country/region, press OK, and then confirm.
PAGE 6
12 插入㆔色列㊞墨匣 Insert the tri-color print cartridge a 重要事㊠：裝置必須為「開啟」狀態，您才可以插入列㊞墨匣。 a 將㆔色列㊞墨匣滑入㊧側插槽，如圖所示。 b 將墨匣的頂部向㆖並向裡穩固㆞推入插槽，直到固定為止。 IMPORTANT: The device must be On before you can insert the print cartridges. b a Slide the tri-color print cartridge into the left slot as shown. b Push the top part of the cartridge firmly up and into the slot until it snaps into place.
PAGE 7
14 校正列㊞墨匣 Align the print cartridges a OK b a 按㆘「OK」列㊞校正頁 (確定您已在底部紙匣放入普通白紙)。 b 從出紙匣取出校正頁。 c 將校正頁㈲列㊞的㆒面向㆘放入進紙器，如圖 c ㆗ 所示。 d 按㆘「OK」掃描校正頁。掃描頁面後，校正即完成。 a Press OK to print the alignment page. (Make sure you have loaded plain white paper in the bottom tray). b Remove the alignment page from the output tray. c Place the alignment page facedown into the document feeder as shown in diagram c. d Press OK to scan the alignment page After the page is scanned, alignment is complete.
PAGE 8
16 放入正確的 CD Insert the correct CD Windows 使用者： a 插入綠色 HP All-in-One Windows CD。 b 依照螢幕㆖的指示安裝軟體。 c 在「連線類型」畫面㆖，確定選取「直接連接㉃電腦」。繼續到㆘㆒頁。附註：如果啟動畫面沒㈲出現，請連按兩㆘「我的電腦」，再連按兩㆘㈲ HP 標誌的「光碟機」圖示，然後連按兩㆘ setup.exe。 Windows Users: a Insert the green HP All-in-One Windows CD. b Follow the onscreen instructions to install the software. c On the Connection Type screen, make sure to select directly to this computer. Continue to the next page.
PAGE 9
17 連接 USB 纜線 Connect the USB cable Windows 使用者： a 依照螢幕㆖的指示進行，直到您看到提示連接 USB 纜線 (這可能會花幾分鐘的時間)。 b 出現提示時，將 USB 纜線㆒頭連接到 HP All-in-One 後方的連接埠，然後將另㆒頭連接到您電腦㆖的任何㆒個 USB 連接埠。 Windows Users: a Follow the onscreen instructions until you see the prompt to connet the USB cable. (This may take several minutes.) b Once the prompt appears, connect the USB cable to the port on the back of the HP Allin-One, and then to any USB port on your computer.
PAGE 10
17 連接 USB 纜線 (續㆖頁) Connect the USB cable (continued) 如果您沒㈲看見此畫面，請參閱最後㆒節的〈疑難排解〉。 If you do not see this screen, see Troubleshooting in the last section. Windows 使用者： c 依照螢幕㆖的指示進行。完成「傳真設定精靈」與「立即註冊」畫面。當您完成軟體安裝後，即完成了所㈲步驟。 Windows Users: c Follow the onscreen instructions. Complete the Fax Setup Wizard and the Sign up now screens. After you complete software installation, you are finished.
PAGE 11
疑難排解問題：「卡紙」訊息出現在顯示器㆖。動作：提起控制台，慢慢㆞清除任何卡住的紙張。確定您已移除所㈲包裝用的膠帶。當您清除卡紙後，請確定將控制台按㆘回到原來的位置。您可能還需要從後方存取擋門或從裝置內部清除任何卡住的紙張。問題：當您插入列㊞墨匣後，出現「移除並檢查列㊞墨匣」訊息。動作：取出列㊞墨匣。確定從銅色的接點㆖撕掉所㈲膠帶。重新插入墨匣，然後關閉列㊞墨匣門。問題：(僅㊜用 Windows) 沒㈲看見畫面提示您連接 USB 纜線。動作：拿出 HP All-in-One Windows CD，再重新插入。參考步驟 16。問題：(僅㊜用 Windows) 顯示 Microsoft「新增硬體」畫面。動作：按㆒㆘「取消」。拔掉 USB 纜線，再插入 HP All-in-One Windows CD。參考步驟 16 和 17。問題：(僅㊜用 Windows) 顯示「裝置安裝無法順利完成」畫面。動作：檢查控制台面板是否穩固裝好。拔掉裝置插頭再重新插㆖。檢查所㈲連線。確定 USB 纜線已插到電腦。請勿將 USB 纜線插到鍵盤或是未開啟電源的集線器。參考步驟 5 和 17。存
PAGE 12
*Q8081-90159* *Q8081-90159* Troubleshooting Q8081-90159 Problem: The paper jam message appears on the display. Action: Lift the control panel and gently remove any jammed paper. Make sure that you removed all packaging tape. After you have clearedd the jam, make sure you press the control panel back into place. You may also need to remove any jammed paper from the rear access door or from inside the device. Problem: The Remove and check print cartridges message appears after you insert print cartridges.