Getting Started HP Notebook
© Copyright 2011 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 1 2 Getting to know your computer ..................................................................................................................... 3 Top .....................
Using TouchPad gestures ................................................................................. 19 Scrolling ............................................................................................ 20 Pinching/Zooming ............................................................................. 20 Rotating ............................................................................................ 21 6 Maintenance ................................................................................
1 Welcome After you set up and register the computer, it is important to take the following steps: 1. Set up your wired or wireless network. For more information, refer to Networking on page 13. 2. Update your antivirus software. For more information, refer to the HP Notebook Reference Guide. For information on finding this guide, refer to Finding information on page 1. 3. Create recovery discs or a recovery flash drive. For more information, refer to Backup and recovery on page 29. 4.
Resource Contents Help and Support ● Operating system information To access Help and Support, select Start > Help and Support. ● Software, driver, and BIOS updates ● Troubleshooting tools NOTE: For country- or region-specific support, go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions.
2 Getting to know your computer Top TouchPad Component (1) Description TouchPad light ● On: The TouchPad is off. ● Off: The TouchPad is on. (2) TouchPad on/off button Turns the TouchPad on and off. Quickly double-tap the TouchPad on/off button to turn the TouchPad on and off. (3) Left TouchPad button Functions like the left button on an external mouse. (4) TouchPad zone Moves the pointer and selects or activates items on the screen.
Lights Component (1) TouchPad light ● On: The TouchPad is off. ● Off: The TouchPad is on. (2) Caps lock light On: Caps lock is on. (3) Power light ● On: The computer is on. ● Blinking: The computer is in Sleep state. ● Off: The computer is off or in Hibernation. ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off.
Buttons Component Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (3) Windows logo key Displays the Windows Start menu. (4) Windows applications key Displays a shortcut menu for items beneath the pointer. (5) Action keys Execute frequently used system functions.
Right side Component Description (1) Optical drive (select models only) Reads and writes to an optical disc. (2) Optical drive light ● Green: The optical drive is being accessed. ● Off: The optical drive is idle. (3) USB port Connects an optional USB device. (4) AC adapter light ● White: The computer is connected to external power and the battery is fully charged. ● Amber: The computer is connected to external power and the battery is charging.
Left side Component Description (1) External monitor port Connects an external VGA monitor or projector. (2) Vents (2) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (3) RJ-45 (network) jack Connects a network cable.
Component Description (9) Hard drive light ● Blinking white: The hard drive is being accessed. (10) Power light ● White: The computer is on. ● Blinking white: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. Display Component Description (1) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) Webcam light On: The webcam is in use. (3) Webcam Records video and captures still photographs.
Bottom Component Description (1) Battery bay Holds the battery. (2) Vents (5) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (3) Battery release latch Releases the battery from the battery bay.
3 HP QuickWeb (select models only) Getting started The HP QuickWeb environment provides a fun and engaging way to perform many of your favorite activities. Your computer is ready to go within seconds of starting HP QuickWeb, allowing you to rapidly access the Internet, widgets, and communication programs. To use QuickWeb, press the QuickWeb key, and then start browsing the Web, communicating with others using Skype, and exploring other HP QuickWeb widgets.
Starting HP QuickWeb ▲ To start HP QuickWeb, press the QuickWeb key when the computer is off or in Hibernation. The following table explains the different behaviors of the QuickWeb key. Key Behavior QuickWeb key ● When the computer is off or in Hibernation, press the key to open HP QuickWeb. ● When the computer is in Microsoft Windows, press the key to open the default Web browser. ● When the computer is in HP QuickWeb, press the key to open the Web browser.
4 Networking NOTE: Internet hardware and software features vary depending on computer model and your location. Your computer may support one or both of the following types of Internet access: ● Wireless—For mobile Internet access, you can use a wireless connection. Refer to Connecting to an existing WLAN on page 14 or Setting up a new WLAN network on page 14. ● Wired—You can access the Internet by connecting to a wired network.
Connecting to a wireless network Wireless technology transfers data across radio waves instead of wires.
Configuring a wireless router For help in setting up a WLAN, refer to the information provided by your router manufacturer or your ISP. The Windows operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network, select Start > Control Panel > Network and Internet > Network and Sharing Center > Set up a new connection or network > Set up a new network. Then follow the on-screen instructions.
5 Keyboard and pointing devices Using the keyboard Using the action keys An action key performs an assigned function. The icon on each of the f1 through f12 keys illustrates the assigned function for that key. To use an action key function, press and hold the key. The action key feature is enabled at the factory. You can disable this feature in Setup Utility (BIOS) and revert back to standard settings by pressing the fn key and one of the function keys to activate the assigned function.
Icon Key Description f7 Plays, pauses, or resumes a track of an audio CD or a section of a DVD or a BD. f8 Plays the next track of an audio CD or the next section of a DVD or a BD. f9 Decreases speaker volume incrementally as long as you hold down the key. f10 Increases speaker volume incrementally as long as you hold down the key. f11 Mutes or restores speaker sound. f12 Turns the wireless feature on or off. NOTE: A wireless network must be set up before a wireless connection is possible.
Turning the TouchPad off or on To turn the TouchPad off or on, quickly double-tap the TouchPad on/off button. NOTE: The TouchPad light is off when the TouchPad is on. The TouchPad light and on-screen display icons indicate the TouchPad status when the TouchPad is turned off or on. The following table shows and describes the TouchPad display icons. TouchPad light Icon Description Amber Indicates that the TouchPad is off. Off Indicates that the TouchPad is on.
Selecting Use the left and right TouchPad buttons as you would use the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To view the demonstration of a gesture: 1. Select Start > Control Panel > Hardware and Sound > Synaptics > Settings. 2. Click a gesture to activate the demonstration.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. NOTE: Two-finger scrolling is enabled at the factory. Pinching/Zooming Pinching allows you to zoom in or out on images or text. ● Zoom in by placing two fingers together on the TouchPad, and then moving them apart.
Rotating Rotating allows you to rotate items such as photos. To rotate, anchor your left forefinger in the TouchPad zone. Move the right forefinger around the anchored finger in a sweeping motion, moving from 12 o’clock to 3 o’clock. To reverse the rotation, move your right forefinger from 3 o’clock to 12 o’clock. NOTE: Rotating is disabled at the factory.
6 Maintenance Inserting or removing the battery NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide. Inserting the battery ▲ Insert the battery (1) into the battery bay and rotate it downward (2) until it is firmly seated. Removing the battery CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information.
2. Remove the battery from the computer (2). Adding or replacing a hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
24 5. Remove the service door (2). 6. Disconnect the hard drive cable from the system board (1), and then lift the hard drive out of the hard drive bay (2).
Installing a hard drive 1. Insert the hard drive into the hard drive bay (1), and then connect the hard drive cable to the system board (2). 2. Align the tabs (1) on the service door with the notches on the computer. 3. Close the service door (2). 4. Tighten the 2 screws (3) on the service door. 5. Replace the battery. 6. Reconnect external power and external devices. 7. Turn on the computer.
Adding or replacing memory modules The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module. CAUTION: Electrostatic discharge (ESD) can damage electronic components.
b. Grasp the edge of the memory module, and then gently pull the memory module out of the memory module slot (2). NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 7.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the module. 8. Align the tabs (1) on the service door with the notches on the computer. 9. Close the service door (2). 10. Tighten the 2 screws (3) on the service door. 11. Replace the battery. 12. Reconnect external power and external devices. 13. Turn on the computer.
7 Backup and recovery Your computer includes tools provided by the operating system and HP to help you safeguard your information and restore it if ever needed.
Guidelines: ● Purchase high-quality DVD-R, DVD+R, DVD-R DL, or DVD+R DL discs. NOTE: Read-write discs, such as CD-RW, DVD±RW, double-layer DVD±RW, and BD-RE (rewritable Blu-ray) discs, are not compatible with the HP Recovery Manager software. ● The computer must be connected to AC power during this process. ● Only one set of recovery discs or one recovery flash drive can be created per computer. NOTE: If you are creating recovery discs, number each disc before inserting it into the optical drive.
Performing a system restore HP Recovery Manager software allows you to repair or restore the computer to its original factory state. HP Recovery Manager works from recovery discs, a recovery flash drive, or from a dedicated recovery partition (select models only) on the hard drive. NOTE: A system restore needs to be performed if the computer hard drive has failed or if all attempts to correct any functional computer issues fail. A system restore should be used as a final attempt to correct computer issues.
4. Select the optical drive or the flash drive. 5. Follow the on-screen instructions. Changing the computer boot order To change the boot order for recovery discs: 1. Restart the computer. 2. Press esc while the computer is restarting, and then press f9 for boot options. 3. Select Internal CD/DVD ROM Drive from the boot options window. To change the boot order for recovery flash drive: 1. Insert the flash drive into a USB port. 2. Restart the computer. 3.
To create a screen shot: 1. Display the screen you want to save. 2. Copy the screen image: To copy only the active window, press alt+prt sc. To copy the entire screen, press prt sc. 3. Open a word-processing document, and then select Edit > Paste. The screen image is added to the document. 4. Save and print the document. Using Windows Backup and Restore Guidelines: ● Be sure that the computer is connected to AC power before you start the backup process.
When to create restore points ● Before you add or modify software or hardware ● Periodically, whenever the computer is functioning optimally NOTE: If you revert to a restore point and then change your mind, you can reverse the restoration. Create a system restore point 1. Select Start > Control Panel > System and Security > System. 2. In the left pane, click System Protection. 3. Click the System Protection tab. 4. Follow the on-screen instructions.
8 Customer support Contacting customer support If the information provided in this user guide, in the HP Notebook Reference Guide, or in Help and Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician.
Labels The labels that are affixed to the computer provide information that you may need when troubleshooting system problems or traveling internationally with the computer: ● Service tag—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support.
9 Specifications Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
Index A AC adapter light, identifying 7 action keys decrease screen brightness 16 Help and Support 16 HP QuickWeb 16 increase screen brightness 16 next track 17 play, pause, resume 17 previous track 16 switch screen image 16 volume down 17 volume mute 17 volume up 17 wireless 17 Action keys, identifying 6 audio-in (microphone) jack, identifying 8 audio-out (headphone) jack, identifying 8 B backing up customized window, toolbar, and menu bar settings 32 personal files 32 battery bay 10, 36 battery release la
N network jack, identifying 8 O operating environment 37 operating system Microsoft Certificate of Authenticity label 36 Product Key 36 P pinching TouchPad gesture 20 pointing devices, setting preferences 17 ports HDMI 8 USB 8 power button, identifying 5 power connector, identifying 7 power light, identifying 9 Product Key 36 product name and number, computer 36 Q QuickWeb Home Screen 12 starting 12 QuickWeb software 11 R recovering from the dedicated recovery partition 31 recovering from the recovery dis
