Installing the RSVLC-0501 Installation Procedures Mounting the Access Point on a Suspended Ceiling T-Rail Installing the RSVLC-0501 2. Turn access point until clips secure T-rail 1.
Installing the RSVLC-0501 Installation Procedures Horizontal Surface Mounting Place the access point on a table or other horizontal surface. The access point accessory kit provides rubber feet that can be used to help keep the access point from sliding on the surface. Attach the rubber feet to the four corners on the bottom of the access point within the embossed circles. Use a sturdy surface in an uncluttered area.
Installing the RSVLC-0501 Installation Procedures 5. Connect the Network Cable Connect the network cable, described under “Cabling Infrastructure” (page 2-4), from the network device or your patch panel to the RJ-45 port on the access point. Using the RJ-45 Connectors Installing the RSVLC-0501 To connect: Push the RJ-45 plug into the RJ-45 port until the tab on the plug clicks into place.
Installing the RSVLC-0501 Installation Procedures 7.
Installing the RSVLC-0501 Installation Procedures Direct Console Access To connect a console to the access point, follow these steps: Installing the RSVLC-0501 1. 8A Connect the PC or terminal to the access point’s Console port using a DB-9 female-tofemale serial cable. (If your PC or terminal has a 25-pin serial connector, first attach a 9-pin to 25-pin straightthrough adapter at one end of the console cable.) The Console cable is described below.
Installing the RSVLC-0501 Installation Procedures Note: As indicated in the following table, some of the wires should not be connected. If you do connect the wires that are labeled “Reserved”, you might get unexpected results with some terminals. Serial interface signal directions DB-9 (DTE) RSVLC-0501 Reserved Reserved GND Reserved Reserved 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 DB-25 (DTE) Terminal or PC Reserved Reserved GND Reserved Reserved 8 3 2 20 7 6 4 5 22 2.
Installing the RSVLC-0501 Sample Network Topologies Sample Network Topologies This section shows you a few sample network topologies in which the RSVLC0501 is implemented. The wireless solution supports a stand-alone wireless network configuration as well as an integrated configuration with wired Ethernet LANs.
Installing the RSVLC-0501 Sample Network Topologies Infrastructure Wireless LAN File Server Wired LAN Extension to Wireless Adapters Desktop PC Switch RSVLC-0501 PC with wireless PCI Adapter The RSVLC-0501 is designed to provide access to a wired LAN for wireless clients. An integrated wired/wireless LAN is called an Infrastructure configuration. A Basic Service Set (BSS) consists of a group of wireless PC users, and an access point that is directly connected to the wired LAN.
Infrastructure Wireless LAN for Roaming Wireless PCs Seamless Roaming for Wireless Clients File Server Desktop PC Switch Wireless Client Switch Wireless Client RSVLC-0501 RSVLC-0501 Wireless Client The Basic Service Set (BSS) defines the communications domain for each access point and its associated wireless clients.
Installing the RSVLC-0501 Sample Network Topologies A wireless infrastructure can also support roaming for mobile workers. More than one access point can be configured to create an Extended Service Set (ESS). By placing the access points so that a continuous coverage area is created, wireless users within this ESS can roam freely. All HP wireless network cards, adapters, and access points within a specific ESS must be configured with the same SSID.
Installing the RSVLC-0501 Sample Network Topologies Installing the RSVLC-0501 — This page is intentionally unused.
3 Getting Started With Access Point Configuration This chapter is a guide for using the access point’s console to quickly assign an Internet Protocol (IP) address and subnet mask to the access point, set a manager password, and, optionally, configure other basic features. For more information on using the access point’s console and the Web browser interface, please see the Management and Configuration Guide, which is on the Documentation CD-ROM that came with your access point.
Getting Started With Access Point Configuration Many other features can be configured through the access point’s console interface to optimize the access point’s performance, to enhance your control of the network traffic, and to improve network security. Once an IP address has been configured on the access point, these features can be accessed more conveniently through a remote Telnet or Secure Shell (SSH) session, or through the access point’s Web browser interface.
Getting Started With Access Point Configuration 3. Type configure to enter global configuration mode. ProCurve RSVLC-0501#configure ProCurve RSVLC-0501(config)# 4. Type password manager password to create a password for the Manager, where password can consist of between 3 and 16 alphanumeric characters and is case sensitive.
Getting Started With Access Point Configuration gateway command, where gateway is the address of the default gateway router. Check with your system administrator to obtain an IP address that is compatible with your network. ProCurve RSVLC-0501(ethernet)#ip address 192.168.2.2 255.255.255.0 ProCurve RSVLC-0501(ethernet)#ip default-gateway 192.168.2.
Getting Started With Access Point Configuration 1. From any command level, type the show radio command followed by the radio number to display the radio’s configuration, including the radio mode, radio channel, and operation status. The following illustration shows the default settings. ProCurve RSVLC-0501# show radio 1 Description Radio 1 - 802.11g Base MAC 00:14:C2:A5:1D:60 Mode 802.
Getting Started With Access Point Configuration 5. To configure the access point’s radio 2 interface, type radio 2 and repeat steps 1 to 4. Note that when the radio 2 interace mode is set to 802.11a, the available channels are 36 to 165, depending on the country setting. 6. To save all configuration settings from the running configuration file to the startup configuration file, type write memory from any command level.
Getting Started With Access Point Configuration Where to Go From Here The above procedure, using the CLI, configured your access point with a Manager password, IP address, and subnet mask. As a result, with the proper network connections, you can now manage the access point from a PC equipped with Telnet or a Secure Shell client, or a Web browser interface. The above procedure also configured the primary Service Set Identifier (SSID), the radio channel, and enabled wireless operation.
Getting Started With Access Point Configuration Using the IP Address for Remote Access Point Management Using the IP Address for Remote Access Point Management With your RSVLC-0501, you can use the access point’s IP address to manage the access point from any PC that is on the same subnet as the access point. You can use either a Telnet or Secure Shell (SSH) session, or a standard Web browser to manage the access point.
Getting Started With Access Point Configuration Using the IP Address for Remote Access Point Management Starting an SSH Session To access the console through an SSH session, SSH v2.0 client software must be installed on the management station PC. Note that after boot up, the access point’s SSH server needs about two minutes to generate host encryption keys. The SSH server is disabled while the keys are being generated. Note The access point supports only SSH version 2.0.
Getting Started With Access Point Configuration Using the IP Address for Remote Access Point Management The administration Web browser must have JavaScript enabled to support the interactive features of the administration interface. It must also support HTTP uploads to use the firmware upgrade feature. Getting Started With Access Point Configuration A typical Web browser interface screen is shown in the next illustration.
4 Using an External Antenna with the RSVLC-0501 The HP RSVLC-0501 provides a variety of external antenna options for extending the radio range and shaping the coverge area. These antennas offer a number of different mounting locations, including indoor or outdoor, wall, ceiling, or radio mast. This chapter shows you how to install an external antenna for your RSVLC0501. Professional Installation Required Only the HP antennas listed in this guide are permitted to be connected to the RSVLC-0501.
Using an External Antenna with the RSVLC-0501 External Antenna Options External Antenna Options The RSVLC-0501 external antenna options are outlined in the following table: Table 4-1. Antenna Type Summary of External Antennas to Use With the RSVLC-0501 Part Number Mounting Horizontal Beamwidth (3dB) Vertical Beamwidth (3dB) J8441A Ceiling or mast 360 Degrees 31 Degrees 2.4 GHz 8 dBi outdoor omnidirectional J8444A Mast 360 Degrees 12 Degrees 2.
Using an External Antenna with the RSVLC-0501 Installation Procedures Installation Procedures Follow these steps to install an external antenna and connect it to the RSVLC0501. Caution Never mount the access point outdoors to be near an external antenna. The access point must always be installed indoors. 1. Plan the Installation Warning ■ Pigtail Cables - Use the coax pigtail cable attached to the antenna to connect to the access point.
Using an External Antenna with the RSVLC-0501 Installation Procedures ■ ■ Warning • For optimum coverage, mount the antenna at the center of the area with a line-of-sight path to all points within the area. • Avoid mounting next to or near building support columns or other obstructions that may cause reduced signal or null zones in parts of the coverage area. • When mounting outdoors using a mast, make sure that the antenna extends beyond the top of the mast.
Using an External Antenna with the RSVLC-0501 Installation Procedures Note that diversity antennas have two pigtail cables. A diversity antenna includes two internal antenna elements that are identical. Both antenna pigtail cables must be connected to the access point for correct operation. Other non-diversity antennas, which have only one pigtail cable, attach to the access point’s “Primary” antenna connector for the appropriate radio. To connect pigtail cables to the access point, follow these steps: 1.
Using an External Antenna with the RSVLC-0501 Installation Procedures 4. Configure the Antenna Mode and Type Using the web browser interface, CLI, or SNMP, you must configure the RSVLC-0501 to use an external antenna. For more information on access point configuration, see the Management and Configuration Guide, which is on the Documentation CD-ROM that came with your access point.
Using an External Antenna with the RSVLC-0501 Installation Procedures Antenna Type selection; Internal or External. Antenna Mode selection; Diversity or Single.
— This page is intentionally unused.
5 This chapter describes how to troubleshoot your HP ProCurve RSVLC-0501. Note that this document describes troubleshooting mostly from a hardware perspective. You can perform more in-depth troubleshooting on the RSVLC0501 using the software tools available with the access point, including the full-featured console interface and the built-in Web browser interface.
Troubleshooting Basic Troubleshooting Tips Troubleshooting Because the RSVLC-0501 behaves in this way (in compliance with the IEEE 802.3 standard), if a device connected to the access point has a fixed configuration at full duplex, the device will not connect correctly to the access point. The result will be high error rates and very inefficient communications between the access point and the device. All devices connected to the RSVLC-0501 should be configured to autonegotiate.
Troubleshooting Diagnosing with the LEDs Table 5-1 shows LED patterns on the access point that indicate problem conditions. 1. Check in the table for the LED pattern that you see on your access point. 2. Refer to the corresponding diagnostic tip on the next few pages. Table 5-1.
Troubleshooting Diagnosing with the LEDs Problem Solution 2 The access point is not receiving power from the PoE source. 1. Verify that access point’s 10/100Base-TX port is attached to a PoE source device. 2. Verify that the PoE source device is powered on, and that the PoE function has been administratively enabled on the source port attached to the access point. 3. Refer to Tip 6 to verify that the network cable is functioning properly.
Troubleshooting Proactive Networking Proactive Networking ■ A graphical Web browser interface that you can use to manage your access point from a PC running a supported Web browser, for example Microsoft Internet Explorer. The Device Information tab can be used to display access point configuration settings, attached client station settings, and the event log.
Troubleshooting Hardware Diagnostic Tests Troubleshooting Hardware Diagnostic Tests Testing the Access Point by Resetting It If you believe that the access point is not operating correctly, you can reset the access point to test its circuitry and operating code. To reset an access point, either Caution ■ Unplug and plug in the power cord (power-cycling). ■ Press the Reset button on the back of the access point for about two seconds (until the LEDs start to blink rapidly).
Troubleshooting Hardware Diagnostic Tests Testing Twisted-Pair Cabling Network cables that fail to provide a link or provide an unreliable link between the access point and the connected network device may not be compatible with the IEEE 802.3 Type 10Base-T, or 100Base-TX standards. The twisted-pair cables attached to the RSVLC-0501 must be compatible with the appropriate standards. To verify that your cable is compatible with these standards, use a qualified cable test device.
Troubleshooting Restoring Custom and Factory Default Configurations Troubleshooting Restoring Custom and Factory Default Configurations As part of your troubleshooting process on the RSVLC-0501, it may become necessary to return the access point’s configuration to custom or factory default settings. This process momentarily interrupts the access point’s operation, clears the console event log, resets the network counters to zero, performs a complete self test, and reboots the access point.
Troubleshooting Restoring Custom and Factory Default Configurations Once the LEDs shut off, release the reset button. The LED shutdown is followed by all LEDs flashing rapidly (about once per second). 3. Release the clear button while the LEDs are still flashing. The configuration sets to the custom default settings and the AP is rebooted. To restore a custom default configuration using the console, execute the erase startup-config command from the console command prompt.
Troubleshooting Downloading New Access Point Software Troubleshooting Downloading New Access Point Software When product enhancements occur for the RSVLC-0501, new software can be downloaded to the access point by several methods. For more information, see the Management and Configuration Guide, which is on the Documentation CD-ROM that came with your access point. The new access point software is made available on the HP ProCurve Web site, http://www.hp.
Troubleshooting HP Customer Support Services Information Item your network records Troubleshooting • copy of your network topology map, including network addresses assigned to the relevant devices Information Location 5-11
— This page is intentionally unused.
A Specifications Physical 21.83 cm (8.60 in) Depth: 13.73 cm (5.40 in) Height: 3.27 cm (1.29 in) Weight: 0.80 kg (1.76 lbs) Specifications Width: Electrical Adapter AC voltage: 100-240 volts, 0.4A, 50/60 Hz DC voltage: 48 volts, 0.38A Power consumption: 11 watts PoE (DC) Input voltage: -48 VDC, 0.15A, 7.2 watts Note: Power can also be provided to the access point through the Ethernet port based on IEEE 802.3af Power over Ethernet (PoE) specifications.
Specifications Connectors ■ The 10/100 Mbps RJ-45 twisted-pair port is compatible with the IEEE 802.3u 100Base-TX and IEEE 802.3 Type 10Base-T standards. Note: To provide Power over Ethernet to the access point, all 4 pairs of wires must be connected for any network cable attached to this port. Safety Specifications Complies with: ■ IEC 60950-1: 2001 ■ EN 60950-1: 2002 ■ UL 60950-1 1st Ed. ■ UL 2043 ■ CAN/CSA-C22.2 No. 60950-1-03 EMC Compliance (Class B) Complies with: ■ FCC Part 15.
Specifications Wireless 802.11b/g IEEE 802.11b/g Radio Technology: Direct Sequence Spread Spectrum (DSSS) Orthogonal Frequency Division Multiplexing (OFDM) Data Rate: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps per channel Operating Frequency: 2.4 ~ 2.4835 GHz (US, Canada, ETSI) 2.4 ~ 2.497 GHz (Japan) Maximum Channels: FCC/IC: 1-11, ETSI: 1-13, MKK: 1-13 (802.11g), 1-14 (802.
Specifications Receiver Sensitivity 802.11b/g Data Rate (Mbps) Typical Receiver Sensitivity (dBm) at 25C 1 -90 11 -85 54 -70 Specifications 802.
B Access Point Port and Network Cables This appendix includes access point connector information and network cable information for cables that should be used with the RSVLC-0501, including minimum pin-out information and specifications for twisted-pair cables. Note Incorrectly wired cabling is the most common cause of problems for LAN communications. HP recommends that you work with a qualified LAN cable installer for assistance with your cabling requirements.
Access Point Port and Network Cables Twisted-Pair Cable/Connector Pin-Outs Twisted-Pair Cable/Connector Pin-Outs The access point includes one 10/100Base-TX port. This port uses the “HP Auto MDIX” feature, which means that you can use either straight-through or crossover twisted-pair cables to connect the access point to a switch.
Access Point Port and Network Cables Twisted-Pair Cable/Connector Pin-Outs Straight-Through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections Because the 10/100 port on the access point supports auto-MDIX operation, you can use either “straight-through” or “crossover” cable for network connections to PCs, servers, hubs, or switches. Cable Diagram Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 1 and 2 on connector “B”.
Access Point Port and Network Cables Twisted-Pair Cable/Connector Pin-Outs Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection Because the 10/100 port on the access point supports auto-MDIX operation, you can use either “straight-through” or “crossover” cable for network connections to PCs, servers, hubs, or switches. Access Point Port and Network Cables Cable Diagram Note Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 3 and 6 on connector “B”.
C Safety and EMC Regulatory Statements Safety Information ! Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. CAUTION A CAUTION in the manual denotes a hazard that can damage the equipment or create a non-compliant condition.
Safety and EMC Regulatory Statements Safety Information Regulatory Model Identification Number Safety and EMC Regulatory Statements For regulatory identification purposes, this product has been assigned a Regulatory Model Number (RMN). The RMN for your product is RSVLC0501. The RMN should not be confused with the marketing name (Wireless Enterprise Access Point 530) or the Product Number (J8986A, J8987A).
Safety and EMC Regulatory Statements Informations concernant la sécurité Informations concernant la sécurité ! Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d'obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d'entraîner des dommages corporels ou la mort.
Safety and EMC Regulatory Statements Hinweise zur Sicherheit Hinweise zur Sicherheit ! Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten. WARNING Eine WARNING in der Dokumentation symbolisiert eine Gefahr, die Verletzungen oder sogar Todesfälle verursachen kann. CAUTION CAUTION in der Dokumentation symbolisiert eine Gefahr, die dis Gerät beschädigen kann.
Safety and EMC Regulatory Statements Considerazioni sulla sicurezza Considerazioni sulla sicurezza ! Simbolo di riferimento alla documentazione. Se il prodotto è contrassegnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso. WARNING La dicitura WARNING denota un pericolo che può causare lesioni o morte. CAUTION La dicitura CAUTION denota un pericolo che può danneggiare le attrezzature.
Safety and EMC Regulatory Statements Consideraciones sobre seguridad Consideraciones sobre seguridad ! Símbolo de referencia a la documentación. Si el producto va marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto. WARNING Una WARNING en la documentación señala un riesgo que podría resultar en lesiones o la muerte. CAUTION Una CAUTION en la documentación señala un riesgo que podría resultar en averías al equipo.
Safety and EMC Regulatory Statements Safety Information (Japan) Safety Information (Japan) Safety and EMC Regulatory Statements C-7
Safety and EMC Regulatory Statements Safety Information (China) Safety and EMC Regulatory Statements Safety Information (China) C-8
Safety and EMC Regulatory Statements EMC Regulatory Statements EMC Regulatory Statements Notice for U.S.A. Manufacturer’s FCC Declaration of Conformity Statement Tested to Comply with FCC Standards Product No: J8986A Regulatory Model No: RSVLC-0501 Manufacturer: Hewlett-Packard Company 3000 Hanover Street Palo Alto, CA 94304-1185 USA Phone: 650-857-1501 For questions regarding this declaration, contact the Product Regulations Manager at the above address or phone number.
Safety and EMC Regulatory Statements EMC Regulatory Statements The FCC requires the user to be notified that any changes or modifications made to the device that are not expressly approved by the Hewlett-Packard Company may void the user’s authority to operate the equipment. If this device is going to be operated in the 5.15 ~ 5.25 GHz frequency range, then it is restricted to an indoor environment only.
Safety and EMC Regulatory Statements EMC Regulatory Statements Notice for European Community This device complies with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC and R&TTE Directive 1999/5/EC. Compliance with these directives implies conformity to harmonized European standards (European Norms) that are listed on the EU Declaration of Conformity that has been issued by HP for this device.
Safety and EMC Regulatory Statements EMC Regulatory Statements 1-13). Pour une utilisation en environnement exterieur, vous devez utiliser les frequencies comprises entre 2454 a 2483.5-MHz (Chaine 10-13). Pour les dernières restrictions, voir http://www.art-telecom.fr. 5 GHz Operation: ■ This device requires the user or installer to properly enter the current country of operation in the 5 GHz Radio Configuration Window as described in the Management and Configuration Guide, before operating this device.
Safety and EMC Regulatory Statements EMC Regulatory Statements Transmit Power Control (TPC) for 5GHz Operation This device employs Transmit Power Control (TPC) to reduce the potential for interference to other communication systems operating in the 5GHz frequency bands. The TPC feature implemented in this Wireless LAN device must be configured by the end-user when operating in any European Community or EFTA country.
Safety and EMC Regulatory Statements EMC Regulatory Statements HP Product Number Power (dBm) Module 1_bg 802.11b: 22 802.11g: 18.5 Module 2_abg 2.4-2.5 802.11a: 17 4.9-5.99 802.11b: 22 802.11g: 18.5 Module 2_abg 802.11a: 17 J8999A J8998A Frequency Range (GHz) 5.15-5.875 Antenna Type Actual Gain (dBi) Directional 6.9/7.7 Omni 6.3 J9000A Module 2_abg 802.11a: 17 5.15-5.875 Directional 13.
Safety and EMC Regulatory Statements EMC Regulatory Statements EU Declaration of Conformity TO BE INCLUDED LATER Safety and EMC Regulatory Statements C-15
Safety and EMC Regulatory Statements EMC Regulatory Statements Notice for Japan Notice for Taiwan Safety and EMC Regulatory Statements DGT LPD (Low Power Device) Statement: C-16
Safety and EMC Regulatory Statements EMC Regulatory Statements Notice for Korea Safety and EMC Regulatory Statements C-17
— This page is intentionally unused.
D Recycle Statements Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Recycle Statements Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen.
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Nolietotu iekārtu iznīcināšanas noteikumi lietotājiem Eiropas Savienības privātajās mājsaimniecībās Šāds simbols uz izstrādājuma vai uz tā iesaiņojuma norāda, ka šo izstrādājumu nedrīkst izmest kopā ar citiem sadzīves atkritumiem. Jūs atbildat par to, lai nolietotās iekārtas tiktu nodotas speciāli iekārtotos punktos, kas paredzēti izmantoto elektrisko un elektronisko iekārtu savākšanai otrreizējai pārstrādei.
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Recycle Statements Descarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem.
Index B 10/100Base-TX connections, length limitations … 2-4 ports, cables used with … 2-4 10/100Base-TX port location on access point … 1-5 back of access point 10/100Base-TX port … 1-5 Auxiliary port … 1-8 Clear button … 1-8 console port … 1-6 description … 1-5 lock … 1-6 network port … 1-6 power connector … 1-6 Reset button … 1-7 basic access point configuration command line interface … 3-2 basic troubleshooting tips … 5-1 blinking LEDs error indications … 5-3 buttons Clear button … 1-8 Reset button … 1
Index cabling infrastructure … 2-4 Clear button description … 1-8 location on access point … 1-8 to delete password protection … 3-7 CLI prompt, console displaying … 2-15 command line interface key command descriptions … 3-6 configuration command line interface … 3-2 DHCP … 3-2 IP address, manually … 3-2 restoring factory defaults … 5-8 connecting the access point to a power source … 2-11 connector specifications … A-2 console checking messages during troubleshooting … 5-6 command line interface … 3-2 disp
L O LAN LED … 1-4 behaviors … 1-4 LEDs behavior during self test … 2-6 blinking definition … 1-4 checking during troubleshooting … 5-6 descriptions of … 1-4 error indications … 5-3 LAN … 1-4 location on access point … 1-3 on access point … 1-4 Power … 1-4 behavior during self test … 2-6 Self Test behavior during self test … 2-6 Wireless … 1-4 length limitations 10/100Base-TX connections … 2-4 location for the access point, considerations … 2-4, 4-3 lock location on access point … 1-6 out-of-band console
Index S safety and regulatory statements … C-1 safety specifications … A-2 self test LED behavior during … 2-6 Power LED behavior … 2-6 Self Test LED behavior during self test … 2-6 serial cable for direct console connection … 2-14 sides of access point antennas … 1-5 specifications connectors … A-2 electrical … A-1 emmissions … A-2 environmental … A-1 physical … A-1 safety … A-2 wireless … A-3 SSH access to the console … 3-9 straight-through cable pin-out … B-3 summary of access point installation … 2-2 o
