ProCurve Radio Port 230 ProCurve Radio Port 210 December 2005 DRAFTv.12 Radio Port Install Guide http://www.procure.
© Copyright 2005 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HewlettPackard.
Introduction The ProCurve Radio Port 230 and ProCurve Radio Port 210, components of the ProCurve Wireless LAN System, link wireless 802.11a/b/g devices to the Ethernet network through a wireless services-enabled switch. These devices are to be used with the HP ProCurve Switch 5300xl with a ProCurve Wireless EDGE Services xl Module or other compatible wireless services-enabled switch products.
• Embedded omni directional diversity antennas • Integrated 10/100 Base TX RJ-45 port • Two LED indicators • Safety wire tie point • Lap-style lock port • Slots for wall mounting • Clips for mounting on a suspended ceiling T-Bar LEDs Radio Characteristics The ProCurve Radio Port 230 comprises two 802.11 radios: (1) a 802.11 b/g radio operating in the 2.4 to 2.5 GHz band and (2) an 802.11a radio operating in the 4.9 to 5.875 GHz band. The ProCurve Radio Port 210 has a single 802.11b/ g radio.
The Radio Port 230 has two LEDs indicators displaying connection status, error conditions, and networking activity for each of the two radios. Operation is as follows: Startup: Radio Port Startup occurs immediately following the application of PoE power, or following a power or software reset. 1. Both GREEN and AMBER LEDs light steadily for several seconds, while the Radio Port performs an internal self-test. 2. The AMBER LED then flashes 3 times per second, while the GREEN LED is off.
1. Match the model number on the purchase order with the model numbers in the packing list and on the case of the device shipped. 2. Verify that the contents of the box include the intended ProCurve Radio Port 230 or 210 and mounting hardware: Radio Port Item Notes 230 210 J9006A J9004A 802.11a & 802.11b/g integrated antenna configuration. 802.11b/g integrated antenna configuration. 3.
Wall mounting consists of hanging the ProCurve Radio Port 230 or 210 along its width or length using the pair of wideshoulder screws provided and mounting slots on the underside of the Radio Port. The ProCurve Radio Port 230 or 210 can be mounted onto any wood, plaster, or cement wall surface using the provided wall anchors when necessary. The illustration shows a horizontal mount. Wall Mount Hardware • Two wide-shoulder Phillips pan head self-tapping screws. • Two wall anchors.
See Detail Below Use these alignment arrows to mark the wall in preparation for installing mounting screws 8
RJ45 Wiring Options The Radio Port case is designed to accommodate multiple options for routing the RJ-45 cable.
Suspended Ceiling Tile T-Bar Mount Mounting the Radio Port 230 or 210 to a suspended ceiling T-Bar grid consists of attaching the Radio Port to the underside of a T-Bar in a suspended ceiling grid, and twisting the Radio Port to lock the case onto the T-Bar. Ceiling Mount Hardware • Safety wire (recommended) and security cable (optional) Ceiling Mount Procedure 1. Lift the ceiling tiles around the T-Bar where the Radio Port is to be installed. 2. If required, loop a safety wire, between 1.01mm (.04in.
To Remove the Radio Port from the T-Bar 1. Lift the ceiling tiles away from the T-Bar to which the Radio Port is attached. 2. Using your finger, depress the T-Bar Retaining Clip that locks the Radio Port to the T-Bar 3. Rotate the Radio Port counter clock-wise to release the T-Bar from the Radio Port’s T-Bar Suspension Clips. Troubleshooting Radio Port Installation This section describes how to troubleshoot the installation of your ProCurve Radio Port primarily from a hardware perspective.
CAUTION 2. The network between the Radio Port and the wireless services-enabled switch has a Layer 2 compatibility issue (e.g. the two devices are on different VLANs.) 3. The wireless services-enabled switch may not be configured properly. In the case of the ProCurve Switch 5300xl, verify that the Wireless EDGE Services xl Module is properly installed, configured, and operational.
Information Item Information Location • details about the Radio Port's status and the status of the wireless services-enabled switch including the software (OS) version of the switch and any installed modules, a copy of the wireless services configuration, • a copy of the switch Event Log, • a copy of the switch status • counters information • Switch console (Wireless Services Configuration Level): show command • switch event Log • Syslog server entry file, if configured • copy of your network topology
Regulatory Model Identification Number For regulatory identification purposes, this product has been assigned a Regulatory Model Number (RMN). The RMN for your product is RSVLC-0502. The RMN should not be confused with the marketing name (ProCurve Radio Port 210, ProCurve Radio Port 230) or the Product Number (J9004A, J9006A). Regulatory Statements Notice for U.S.A.
z The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
5 GHz Operation: • • • "This device requires the user to properly enter the current country of operation during the initial setup of the Radio Port. Once the country of operation has been entered, the Radio Port will automatically limit the available channels, ensuring compliant operation in the selected country. Incorrectly entering the country of operation may result in illegal operation and may cause harmful interference to other systems.
Notice for Canada This device complies with the limits for a Class B digital device and conforms to Industry Canada standard ICES-003. Products that contain a radio transmitter comply with Industry Canada standard RSS210 and are labeled with an IC approval number. Cet appareil numérique de la classe B est conforme à la norme ICES-003 de Industry Canada. La radio sans fil de ce dispsitif est conforme à la certification RSS 210 de Industry Canada et est étiquetée avec un numéro d'approbation IC.
EU Declaration of Conformity DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Manufacturer's Name: Hewlett-Packard Company Manufacturer's Address: 8000 Foothills Blvd. Roseville, CA 95747-5502 U.S.A.
Notice For Japan Notice For Taiwan: DGT LPD (Low Power devices) Statement 19
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements 1 Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa Liidus See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektrija elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti.
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Készülékek magánháztartásban történő selejtezése az Európai Unió területén A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltérő módon kezelendő. A vásárló a hulladékká vált készüléket köteles a kijelölt gyűjtőhelyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából.
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Pozbywanie się zużytego sprzętu przez użytkowników w prywatnych gospodarstwach domowych w Unii Europejskiej Ten symbol na produkcie lub jego opakowaniu oznacza, że produktu nie wolno wyrzucać do zwykłych pojemników na śmieci. Obowiązkiem użytkownika jest przekazanie zużytego sprzętu do wyznaczonego punktu zbiórki w celu recyklingu odpadów powstałych ze sprzętu elektrycznego i elektronicznego.
Waste Electrical and Electronic Equipment (WEEE) Statements Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet genom att överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska produkter.
