ProCurve Radio Port 220 December 2005 DRAFT v.14 Radio Port Install Guide http://www.procure.
© Copyright 2005 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HewlettPackard.
Introduction The ProCurve Radio Port 220, a component of the ProCurve Wireless LAN System, links wireless 802.11a/b/g devices to the Ethernet network through a wireless services-enabled switch. This device is to be used with the HP ProCurve Switch 5300 xl, with a ProCurve Wireless EDGE Services xl Module, or other compatible wireless services-enabled switch product.
Bottom View Mount Slots Light Pipe Clip Slots Front View Rear View RJ-45 Lock Port The lock port, compatible with laptop-style security cables, is on the side of the case.
Technical Specifications Operating Voltage Operating Current Power Operating Temperature Non-Operating/Storage Temperature Operating Humidity Non-Operating/Storage Humidity Operating Altitude (max) Non-Operating/Storage Altitude Plenum Rated 48VDC (from 802.3af-compliant power source) 148mA (typical) 7W (typical) -4 to 122° F (-20 to 50° C) -40°F to 158°F (-40 to 70°C ) 5 to 95% (non-condensing) 5 to 95% (non-condensing) 10,000 ft (3,048 m) 15,000ft.
LED Indicators The Radio Port 220 has LED indicators on the front of the case that visually display the status of the device. When the Radio Port is mounted above a suspended ceiling, an additional set of LED indicators on the back of the unit can be extended through the ceiling tile using a provided lightpipe extender, making the Radio Port location and status visible from below the ceiling. Wall Mount. Top View RSMA Antenna Connectors 5 Ghz Primary 2.4 Ghz Primary LEDs 5 Ghz Secondary 2.
3.Both LEDs then go off for a moment, followed by both LEDs lighting steadily for a few seconds. 4.After this sequence, assuming no error conditions have occurred, the Radio Port will enter Normal operation mode. This means that the Radio Port has successfully communicated with and been adopted by a wireless services-enabled switch.
Wall Mount Wall mounting consists of hanging the ProCurve Radio Port 220 along its width or length using the pair of wideshoulder mounting screws provided, and mounting slots on the bottom of the unit. The ProCurve Radio Port 220 can be mounted onto any wood, plaster, or cement wall surface using the provided wall anchors when necessary. The illustration shows a vertical mount.
6. If required, install and attach a security cable to the Radio Port's lock port. The lock port, compatible with laptop-style security cables, is on the side of the case. Attach the opposite end of the security cable to a secure, stationary point. 7. Attach the appropriate antennas to the Radio Port's antenna connectors. Pay close attention to ensure that the appropriate antenna for each frequency band is attached to the appropriate antenna connector for that frequency band on the Radio Port.
Ceiling Mount Procedure 1. If possible, remove the ceiling tile from its frame and place it, finished side down, on a work surface. 2. Mark a point on the upper or unfinished side of the tile where the light pipe extender will be installed. It is best to leave at least 5 cm (2 in.) or more between the edge of the ceiling tile and the center of the light pipe to allow clearance for placement of the Radio Port and antenna connections above the ceiling tile. 3.
Caution HP Product Number Frequency Range (GHZ Antenna Type/ Coverage Diversity Actual Gain w/ specified cable (dBi) J8448A 2.4 Directional pointto-point (Yagi) No 13.8 J8997A 2.4/5.0 Omni-directional (ceiling-mount panel) Yes 3.0/4.0 J8998A 5.0 Indoor/Outdoor Omni-directional (dipole) No 6.3 J8999A 2.4/5.0 60-degree Directional (panel) No 6.9/7.7 J9000A 5.0 25- degree Directional (panel) No 13.
LED Error Indicators GREEN LED Off steadily while Ethernet cable is linked to a PoE source. Remains off even when Radio Port is disconnected from Ethernet cable and reconnected. AMBER LED Off steadily while Ethernet cable is linked to a PoE source. Remains off even when Radio Port is disconnected from Ethernet cable and reconnected.
to get technical support. The HP ProCurve web site, www.procurve.com also provides up-to-date support information under product support. In addition, your HP-authorized network reseller can provide you with assistance, both with services that they offer and with services offered by HP.
Grounding • • If your LAN covers an area served by more than one power distribution system, be sure their safety grounds are securely interconnected. LAN cables may occasionally be subject to hazardous transient voltages (such as lightning or disturbances in the electrical utilities power grid). Handle exposed metal components of the network with caution. Servicing There are no user-serviceable parts inside this product.
z z z The antenna 4 of this device requires Professional installation to satisfy the FCC requirements, and its Maximum output is 19.5 dBm. Operations in the band 5.15-5.25GHz are restricted to indoor usage only. FCC RF exposure compliance for specific co-located transmitter conditions (radio port 230) was evaluated for mobile operating configurations, other co-located configurations or operations in conjunction with any other antenna or transmitter are not authorized and require separate FCC approval.
• • In France, this device may use the entire 2400 - 2483.5 MHz band (Channels 1 through 13) for indoor applications. For outdoor use, only the 2400 - 2454 MHz frequency band (Channels 1 through 7) may be used. For the latest requirements, see http://www.art-telecom.fr. L'utilisation de cet equipement (2.4GHz wireless LAN) est soumise à certaines restrictions: cet equipement peut être utilisé à l'interieur d'un batiment en utilisant toutes les frequences de 2400 a 2483.5MHz (Chaine 1-13).
Notice For Canada This device complies with the limits for a Class B digital device and conforms to Industry Canada standard ICES-003. Products that contain a radio transmitter comply with Industry Canada standard RSS210 and are labeled with an IC approval number. Cet appareil numérique de la classe B est conforme à la norme ICES-003 de Industry Canada. La radio sans fil de ce dispsitif est conforme à la certification RSS 210 de Industry Canada et est étiquetée avec un numéro d'approbation IC.
EU Declaration of Conformity: DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Manufacturer's Name: Hewlett-Packard Company Manufacturer's Address: 8000 Foothills Blvd. Roseville, CA 95747-5502 U.S.A.
Notice For Japan Notice For Taiwan: DGT LPD (Low Power devices) Statement 19
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements 1 Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa Liidus See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektrija elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti.
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Készülékek magánháztartásban történő selejtezése az Európai Unió területén A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltérő módon kezelendő. A vásárló a hulladékká vált készüléket köteles a kijelölt gyűjtőhelyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából.
Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Pozbywanie się zużytego sprzętu przez użytkowników w prywatnych gospodarstwach domowych w Unii Europejskiej Ten symbol na produkcie lub jego opakowaniu oznacza, że produktu nie wolno wyrzucać do zwykłych pojemników na śmieci. Obowiązkiem użytkownika jest przekazanie zużytego sprzętu do wyznaczonego punktu zbiórki w celu recyklingu odpadów powstałych ze sprzętu elektrycznego i elektronicznego.
Waste Electrical and Electronic Equipment (WEEE) Statements Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet genom att överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska produkter.
