HP Photosmart C8100 All-in-One series
Computer connection information The HP All-in-One comes equipped with a USB port so you can connect directly to a computer using a USB cable. You can also connect the HP All-in-One to either a wired or wireless network. Additionally, the built-in Bluetooth® Wireless Technology allows Bluetooth® devices to print to the HP All-in-One. This section contains the following topics: Supported connection types Connect using Ethernet Connect using integrated wireless WLAN 802.
Chapter 4 Connect using integrated wireless WLAN 802.11 The HP All-in-One uses an internal networking component that supports a wireless network. For detailed instructions on connecting the HP All-in-One to a wireless (802.11) network, see “Integrated wireless WLAN 802.11 network setup” on page 32. Connect using an integrated wireless Bluetooth® connection Finish setup The integrated wireless Bluetooth® connection allows you to print images from most Bluetooth devices, including computers.
6. When you have finished entering a name for the HP All-in-One, touch OK. The name you entered will appear on your Bluetooth device when you connect to the HP All-in-One to print. 7. Touch OK to exit the Setup menu. Set Bluetooth security for the HP All-in-One You can enable printer security settings through the Bluetooth menu on the HP All-inOne. Touch Setup on the display, and then touch Bluetooth.
Chapter 4 5. Use the visual keyboard to enter a new passkey. NOTE: The passkey must be 1 to 4 characters long, and can only consist of numbers. Finish setup 6. When you have finished entering your passkey, touch OK. The Bluetooth menu appears. 7. Touch Security Level. 8. Touch High. High level security requires authentication. Passkey authentication is now set for the HP All-in-One.
To turn the Bluetooth radio on and off 1. Touch Setup on the display. 2. Touch Bluetooth. or 3. Touch Bluetooth Radio. 4. Touch On or Off. Reset Bluetooth settings on the HP All-in-One You can reset all of the Bluetooth settings on the HP All-in-One to the factory defaults. NOTE: Only select Reset Bluetooth if you want all of the HP All-in-One Bluetooth settings returned to factory defaults. To reset the Bluetooth settings 1. Touch Setup on the display. 2. Touch Bluetooth.
Chapter 4 To install and print using the Microsoft stack 1. Make sure that you have installed the HP All-in-One software on the computer. Finish setup NOTE: The purpose of installing the software is to make sure the printer driver is available for the Bluetooth® connection. Therefore, if you have already installed the software, you do not need to reinstall it. If you want both a USB and a Bluetooth® connection to the HP All-in-One, install the USB connection first.
Chapter 16 This section contains the following topics: Technical information • Regulatory model identification number • FCC statement • Laser compliance • Notice to users in Korea • VCCI (Class B) compliance statement for users in Japan • Notice to users in Japan about power cord • Geräuschemission Regulatory model identification number For regulatory identification purposes, your product is assigned a Regulatory Model Number. The Regulatory Model Number for your product is SDGOB-0712.
Laser compliance This laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated May 27, 2001; and with IEC 60825-1:1993/A2:2001. WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product’s installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation: -- Do not try to open the module enclosure.
Chapter 16 Regulatory wireless statements This section contains the following regulatory information pertaining to wireless products: Technical information • Wireless: Exposure to radio frequency radiation • Wireless: Notice to users in Brazil • Wireless: Notice to users in Canada • European Union Regulatory Notice • Wireless: Notice to users in Taiwan Wireless: Exposure to radio frequency radiation Exposure to radio frequency radiation Caution The radiated output power of this device is far b
European Union Regulatory Notice European Union Regulatory Notice Products bearing the CE marking comply with the following EU Directives: Low Voltage Directive 73/23/EEC EMC Directive 2004/108/EC Technical information • • CE compliance of this product is valid only if powered with the correct CE-marked AC adapter provided by HP.
Chapter 16 Declaration of conformity (European Economic Area) The Declaration of Conformity in this document complies with ISO/IEC 17050-1 and EN 17050-1. It identifies the product, manufacturer’s name and address, and applicable specifications recognized in the European community.
