Installation Guide hp rp8400 Server Series Third Edition Version 4.
Legal Notices The information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material. Restricted Rights Legend.
Contents 1. Introduction Customer Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparing the Site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accepting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HP Installation Specialist Responsibilities .
Contents Verifying Presence of the Cell Boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring AC Line Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Powering On the hp rp8400 Server Series Cabinet (48 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Verifying the System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables Table 1. Revisions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 3-1. Wheel Kit Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Table A-1. Factory-Integrated Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables 6
Figures Figure 2-1. Power Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-1. Removing the Polystraps and Cardboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-2. Removing the Shipping Bolts and Plastic Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 3-3. Preparing to Roll Off the Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures 8
Preface This guide provides the HP Installation Specialist with the background information and procedures needed to install the hp rp8400 server series.
Revision History Table 1 Edition Revisions Part Number Release Date Description Second A6093-96012 August 2002 Updated with additions and corrections. Third A6093-960 August 2003 Added Configuring a Web Console on the MP to Chapter 5.
Scope The information contained in this manual applies to the hp rp8400 server series. This guide is divided into the following chapters: • Chapter 1, “Introduction”—Describes the responsibilities of the customer and the HP Installation Specialist prior to and during installation. • Chapter 2, “Safety Considerations”—Lists the safety considerations for installing a new system or upgrading an existing system.
Warnings, Cautions and Notes This document presents warnings, cautions and notes in the following format. WARNING A warning highlights information that if not adhered to could cause harm or injury to personnel. CAUTION A caution highlights procedures or information necessary to avoid damage to equipment, damage to software, loss of data, or invalid test results. NOTE A note highlights supplemental information.
Safety and Regulatory Information For your protection, this product has been tested to various national and international regulations and standards. The scope of this regulatory testing includes electrical/mechanical safety, radio frequency interference, ergonomics, acoustics, and hazardous material. Where required, approvals obtained from third-party test agencies are shown on the product label. Safety in Material Handling WARNING Do not lift the server manually.
EMI Statement (European Union Only) This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Digital Apparatus Statement (Canada) This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. BSMI (Taiwan) This product has been reviewed and is fully compliant to CNS 13438 (CISPR 22: 1993) Class A.
In command syntax diagrams, italic identifies variables that must be supplied by the user. Bold 16 In paragraph text, bold identifies either equipment markings or actions that require an operator response.
Associated Documents The following is a list of other documents that provide more details on the topics presented in this manual: • Standard for the Protection of Electronic Computer Data Processing Equipment, (NFPA75) National Fire Protection Association • EIA Standard RS-232-C, Electronic Industries Association • Electrostatic Discharge Failures of Semiconductor Devices, Unger, B.A.
1 Introduction This chapter contains a general description of the responsibilities of the Customer and HP Installation Specialist before and during an installation.
Introduction Customer Responsibilities Customer Responsibilities The customer is responsible for: • Preparing the Site • Accepting the Equipment Preparing the Site The customer and a Hewlett-Packard representative should review the site survey and site inspection checklists located in the Site Preparation Guide: hp rp8400 server series to identify potential problems that may arise before, during, or after installation of the system.
Introduction HP Installation Specialist Responsibilities HP Installation Specialist Responsibilities The HP Installation Specialist is responsible for: • Unpacking the equipment • Installing the cabinets • Connecting the system to AC power • Completing the installation report Tool Requirements The following list provides the HP Installation Specialist with the recommended tools for performing the unpacking and installation process.
Introduction HP Installation Specialist Responsibilities CAUTION Do not leave side or top covers off the server for extended periods of time while troubleshooting the server. Overall reliability of the server will be compromised if covers are not replaced after servicing. Connecting and Testing AC Power After the equipment has been unpacked and moved into position, it must be connected to the site AC power supply.
2 Safety Considerations It is important to observe safety procedures when installing Hewlett-Packard computers and their peripheral devices. General guidelines are provided in this chapter.
Safety Considerations Input Power Ratings Input Power Ratings Each cabinet has a label mounted at the rear of the cabinet that lists its input power rating. See Figure 2-1 for the cabinet power label. WARNING Safety warning labels affixed to the rear of the processor must be in the correct language for the installation and must show the power configuration of the power controller. Incorrect labels may result in injury to personnel and damage to equipment.
Safety Considerations Input Power Ratings 3. Facility circuit breakers are adequate for specified cabinet current loads. Refer to the Site Preparation Guide: hp rp8400 server series for circuit breaker size requirements. 4. Facility AC power connection to the processor cabinet complies with and is tested by guidelines set forth in Chapter 4, “AC Power.
Safety Considerations Electrical Safety Precautions Electrical Safety Precautions Hazardous voltages are present inside the server cabinet while the site AC circuit breakers are set to ON. Ensure that the site AC circuit breakers are set to OFF before servicing the system. Circuit Breakers WARNING 26 Set all AC input circuit breakers to the OFF position before connecting a power cable plug to the facility’s AC power. Failure to do so may cause injury to personnel.
3 Unpacking Inspect shipping containers when the equipment arrives at the site. Check equipment after the packing has been removed. This chapter discusses how to inspect and receive the hp rp8400 server cabinet.
Unpacking NOTE The server will ship in one of three different configurations. The configurations are on a pallet in a Rosebowl II cabinet, on a pallet for rack mount into an existing cabinet on the customer site, and on a pallet with a wheel kit for installation as a standalone server.
Unpacking Inspecting the hp rp8400 Server Cabinet Inspecting the hp rp8400 Server Cabinet Hewlett-Packard shipping containers are designed to protect their contents under normal shipping conditions. After the equipment arrives at the customer site, carefully inspect each carton for signs of shipping damage. A tilt indicator is installed on each carton shipped. The beads in the indicator will roll to the upper position if the container has been tilted to an angle that could cause equipment damage.
Unpacking Receiving the hp rp8400 Server Cabinet Receiving the hp rp8400 Server Cabinet This section contains information pertaining to unpacking the server cabinet. WARNING Wear protective glasses while cutting the plastic bands around the shipping container. These bands are under tension. When cut, they can spring back and cause serious eye injury. NOTE Position the pallet allowing for enough space to roll the cabinet off the pallet before starting.
Unpacking Receiving the hp rp8400 Server Cabinet Step 3. Remove the corrugated wrap from the pallet. Step 4. Remove the packing materials. CAUTION The plastic wrapping material should be cut off rather than pulled off. Pulling the plastic covering off represents an ESD hazard. Step 5. Remove four bolts holding down the ramps and remove the ramps. NOTE Figure 3-2 shows one ramp attached to the pallet on either side of the cabinet with each ramp secured to the pallet using two bolts.
Unpacking Receiving the hp rp8400 Server Cabinet Step 6. Remove the six bolts from the base attaching the rack to the pallet. Figure 3-3Preparing to Roll Off the Pallet WARNING 32 Make sure that the leveling feet on the rack are raised before you roll the rack down the ramp and any time you roll the rack on the casters. Use caution when rolling the cabinet off the ramp. A single server in the cabinet weighs approximately 508 pounds.
Unpacking Receiving the hp rp8400 Server Cabinet Securing the Cabinet Once in position, secure and stabilize the cabinet using the leveling feet at the corners of the base and install the anti-tip mechanisms on the bottom front and rear of the rack.
Unpacking Rack Mount System Installation Rack Mount System Installation Servers shipped as a stand alone or in the to be racked configuration must have the core I/O handles and the PCI towel bars attached at system installation. Obtain and install the core I/O handles and PCI towel bars from the accessory kit A6093-04046. The towel bars and handles are the same part. Refer to service note A6093A-11. There are several documents written to help with rack mounting the server.
Unpacking Rack Mount System Installation This procedure should only be performed by FOUR (4) qualified HP Service Personnel utilizing proper lifting techniques and procedures. System damage can occur through improper removal and re-installation of devices. This task must be performed by trained personnel only. Instructions for removing and re-installing these components can be found in the Removal & Replacement chapter of the Service Guide.
Unpacking Rack Mount System Installation • Installing the ballast kit (J1479A) • Installing the barrel nuts on the front and rear columns • Installing the slides Step 2. Follow the instructions on the outside of the server packaging to remove the banding and carton top from the server pallet. Step 3. Insert the lifter forks between the cushions. Figure 3-5Pallet Cushion Layout without Server on Pallet Position the Lifter Forks at These Insertion Points Step 4.
Unpacking Rack Mount System Installation Step 5. Slowly raise the server off the pallet until it clears the pallet cushions. Figure 3-6Raising the Server Off the Pallet Cushions Step 6. Carefully roll the lifter and server away from the pallet. Do not raise the server any higher than necessary when moving it over to the rack. Step 7.
Unpacking Wheel Kit Installation Wheel Kit Installation Compare the packing list with the contents of the wheel kit before beginning the installation. Table 3-1 Wheel Kit Packing List Part Number Description Quantity A6093-04081 Pedestal Cover Assembly 2 A6093-04082 Right Front Caster Assembly 1 A6093-04083 Right Rear Caster Assembly 1 A6093-04084 Left Front Caster Assembly 1 A6093-04085 Left Rear Caster Assembly 1 0515-2478 M4 x 0.
Unpacking Wheel Kit Installation 1. Cut and remove the polystrap bands securing the HP Server to the pallet. 2. Lift the carton top from the cardboard tray resting on the pallet. 3. Remove the bezel kit carton and top cushion from the pallet. Figure 3-7 Bezel Kit and Top Cushion Top Cushions Bezel Kit Cardboard Tray Pallet 4. Unfold bottom cardboard tray.
Unpacking Wheel Kit Installation 5. Remove the front cushion only. Do not remove any other cushions until further instructed. Figure 3-8 Removal of Cushion from Front Edge of Server Rear Cushion Side Cushion Front Cushion 6. Open the wheel kit box and locate the two front casters. The front casters are shorter in length than the two rear casters. Each front caster is designed to fit only on one corner of the server. There is a right front caster and a left front caster.
Unpacking Wheel Kit Installation 7. Remove two of the eight screws from the plastic pouch. Attach one wheel caster to the front of the server. Figure 3-9 Attaching a Caster Wheel to the Server Front Caster 8. Attach the remaining front caster to the server using two more screws supplied in the plastic pouch. 9. Remove the rear cushion at the rear of the server. Do not remove the remaining cushions. 10. Mount the two rear casters to the server using the remaining four screws. 11.
Unpacking Wheel Kit Installation 12. Attach the ramp to the edge of the pallet. Note there are two pre-drilled holes in the ramp. Use the two screws taped to the ramp and attach it to the pallet.
Unpacking Wheel Kit Installation 13. Remove the two side cushions from the server and unfold the cardboard tray so that it lays flat on the pallet. Figure 3-11 Side Cushion Removal from Server Side Cushion Ramp 14. Carefully roll the server off the pallet and down the ramp. 15. Obtain the pedestal covers from the wheel kit. Note that the pedestal covers are designed to fit on either side of the server.
Unpacking Wheel Kit Installation 16. Insert the slot on the pedestal cover into the front caster. Secure the pedestal cover to the server by tightening the captive screw on the cover at the rear of the server.
Unpacking Wheel Kit Installation 17. Wheel kit installation is complete once both pedestal covers are attached to the server and the bezel cover is snapped into place on the front of the server.
Unpacking Power Distribution Unit Power Distribution Unit The server may ship with a 60A Power Distribution Unit (PDU). The NEMA PDU will have four 20A circuit breakers. The IEC PDU will have four 16A circuit breakers. Each circuit breaker will have two IEC 320-20 outlets associated with each breaker providing a total of eight IEC 320-20 outlets. The PDU will be 3U high and will be rack-mounted in the server cabinet Documentation for installation will accompany the PDU.
4 AC Power Once the system has been unpacked and moved into position, it must be connected to a source of AC power which must be checked before the system is powered up. This chapter describes these activities.
AC Power • 48 Wiring and Voltage Checks Chapter 4
AC Power Overview Overview The hp rp8400 server series has an AC power plug on a 3-wire AC power cable. These systems connect to a power source of 200-240 V AC. WARNING Do not set site AC circuit breakers serving the cabinet(s) to ON before verifying that the cabinet has been wired into the site AC power supply correctly. Failure to do so may result in injury to personnel or damage to equipment when AC power is applied to the cabinet.
AC Power AC Power Connections AC Power Connections This section provides a brief overview of concerns to be aware of when attaching the site AC power to the server cabinet. See the Site Preparation Guide for the hp rp8400 Server Series for a more detailed explanation. Hewlett-Packard personnel should not be directly involved in the selection of material, installation, or connection of site AC power.
AC Power Wiring and Voltage Checks Wiring and Voltage Checks This section details the methods to check wiring and voltage before powering up a new system. WARNING Do not set site AC circuit breakers serving the cabinet(s) to ON before verifying that the cabinet has been wired into the site AC power supply correctly. Failure to do so may result in injury to personnel or damage to equipment when AC power is applied to the cabinet.
AC Power Wiring and Voltage Checks Verify the connection of the cabinet ground to site AC power ground through a continuity check between the cabinet and site AC power supply ground. The continuity check should be performed while the site AC power supply circuit breakers serving the cabinet and the cabinet circuit breaker are all set to OFF. Use the following procedure to verify that the cabinet ground connects to the site AC power supply ground: Step 1.
AC Power Wiring and Voltage Checks Voltage Range Verification of Receptacle This procedure measures the voltage between L1 and L2, then from L1 to ground and finally from L2 to ground. Three separate measurements will be performed during this procedure. Refer to Figure 4-1 for voltage reference points when performing the following measurements. Figure 4-1Voltage Reference Points for IEC 320 C19 Plug Step 1. Measure the voltage between L1 and L2.
AC Power Wiring and Voltage Checks Safety Ground Verification (Single Power Source) This procedure measures the voltage level between A0 and A1. The voltage level between B0 and B1 will also be verified. All measurements will be taken between ground pins. Refer to Figure 4-2 for ground reference points when performing these measurements. Figure 4-2Safety Ground Reference Check - Single Power Source Step 1. Measure the voltage between A0 and A1.
AC Power Wiring and Voltage Checks Safety Ground Verification (Dual Power Source) This procedure measures the voltage level between A0 and A1, between B0 and B1, between A0 and B0 and between A1 and B1. All measurements will be taken between ground pins. Refer to Figure 4-3 for ground reference points when performing these measurements. Figure 4-3Safety Ground Reference Check - Dual Power Source Step 1. Measure the voltage between A0 and A1. Take the AC voltage down to the lowest scale on the volt meter.
AC Power Wiring and Voltage Checks Voltage Check (Additional Procedure) The voltage check ensures that all phases (and neutral, for international systems) are connected correctly to the cabinet and that the AC input voltage is within limits. This procedure will need to be performed if the previous voltage check procedure did not yield the expected results as previously outlined.
AC Power Wiring and Voltage Checks WARNING SHOCK HAZARD Risk of shock hazard while testing primary power. Use properly insulated probes. Be sure to replace access cover when finished testing primary power. Step 10. Set the server power to ON. Step 11. Check that the indicator light on each power supply is lit.
AC Power Wiring and Voltage Checks Regulatory and System Serial Number Label Check A system serial number is located on the regulatory label affixed to cabinet. This label is printed in the appropriate language for the installation location. The serial number check verifies that the label is affixed to the server and that it is printed in the correct language. Refer to Figure 4-5 for label details.
5 System Installation This chapter contains the procedures for completing the system installation procedures for the hp rp8400 server series.
System Installation • “Turning On Housekeeping Power and Logging in to the MP” • “Configuring LAN Information for the MP” • “Configuring the Management Processor for use with a Web Console” • “Verifying Presence of the Cell Boards” • “Configuring AC Line Status” • “Powering On the hp rp8400 Server Series Cabinet (48 V)” • “Verifying the System Configuration” • “Adding Processors with Instant Capacity On Demand (iCOD)” • “Booting HP-UX on the Partition(s)” 60 Chapter 5
System Installation hp rp8400 Server Series AC Input Power hp rp8400 Server Series AC Input Power The server can receive AC input from two different AC power sources. If two separate power sources are available, the server can be plugged into the separate power sources increasing system reliability should one power source fail. The main power source is defined to be A0 and A1. The redundant power source is defined to be B0 and B1. See Figure 5-1 for the AC power input label scheme.
System Installation hp rp8400 Server Series AC Input Power See Figure 5-2 for the graphical representation of how the input power cords supply power to each BPS. Figure 5-2 CAUTION Distribution of Input Power for Each Bulk Power Supply Do not route data and power cables together in the same cable management arm. Do not route data and power cables in parallel paths in close proximity to each other. The suggested minimum distance that the data and power cables should be apart is 3 inches (7.
System Installation hp rp8400 Server Series AC Input Power Applying Power to the hp rp8400 Server Series Initial observations can be made as to the functionality of the server before attaching any LAN or serial cables, the system console or any peripherals to the server. When an active AC power source is first applied to the server, the following observations can be made at three different intervals or points in time.
System Installation Setting Up the CE Tool (PC) Setting Up the CE Tool (PC) The CE Tool is usually a laptop. It allows communication with the Management Processor (MP) in the server. The MP monitors the activity of either a one partition or a multiple partition configuration.
System Installation Setting Up the CE Tool (PC) If the CE Tool is a laptop using Reflection 1, check or change these communications settings using the following procedure: 1. From the Reflection 1 Main screen, pull down the Connection menu and select Connection Setup. 2. Select Serial Port. 3. Select Com1. 4. Check the settings and change, if required. Go to More Settings to set Xon/Xoff. Click OK to close the More Settings window. 5. Click OK to close the Connection Setup window. 6.
System Installation Setting Up the CE Tool (PC) 1. Connect one end of a null modem cable (9-pin to 9-pin) (Part Number 5182-4794) to the Local RS-232 port on the Core I/O card (the DB9 connector located at the bottom of the Core I/O card). Figure 5-3 LAN and RS-232 Connectors on the Core I/O Board RS-232 UPS Port SYSTEM LAN Port RS-232 Remote Port GSP LAN Port RS-232 Local Port 2. Connect the other end of the RS-232 cable to the CE Tool.
System Installation Turning On Housekeeping Power and Logging in to the MP Turning On Housekeeping Power and Logging in to the MP After connecting the serial display device, the power to the server cabinet is now ready to be turned On to get a login prompt for the Management Processor (MP). Switching the power to On allows power to flow to the Bulk Power Supplies (BPS) located at the front of the server cabinet, which in turn provides housekeeping power (HKP).
System Installation Turning On Housekeeping Power and Logging in to the MP • after 30 seconds has elapsed. Note the flashing amber BPS LED for each BPS becomes a flashing green LED Figure 5-5 BPS LED Location 3. Login to the MP: a. Enter Admin at the login prompt. (This term is case sensitive.) It takes a few moments for the MP prompt to appear. If it does not, make sure the laptop serial device settings are correct: 8 bits, no parity, 9600 baud, and None for both Receive and Transmit. Then, try again.
System Installation Turning On Housekeeping Power and Logging in to the MP The MP Main Menu appears: Figure 5-6 MP Main Menu MP login: Admin MP password: Welcome to the S Class 16K-A Management Processor (c) Copyright 1995-2001 Hewlett-Packard Co., All Rights Reserved. Version 0.
System Installation Configuring LAN Information for the MP Configuring LAN Information for the MP This section describes how to set and verify the server Management Processor (MP) LAN port information. LAN information includes the MP network name, the MP IP address, the subnet mask, and gateway address. This information is provided by the customer. To set the MP LAN IP address: 1. At the MP Main Menu prompt (MP>), enter cm. From the MP Command Menu prompt (MP:CM>), enter lc (for LAN configuration).
System Installation Configuring LAN Information for the MP 5. Confirm the new address. 6. Enter the MP Network Name. This is the host name for the customer LAN. The name can be as many as 64 characters, and include alpha numerics, - (dash), _ (under bar), . (period), or a space. It is recommended that the name be a derivative of the complex name. For example, Acme.com_MP. 7. Enter the LAN parameters for Subnet mask and Gateway address. This information shall come from the customer. 8.
System Installation Configuring the Management Processor for use with a Web Console Configuring the Management Processor for use with a Web Console The Web console is an embedded feature of the management processor (MP). The Web console allows access to the server via the LAN port on the core I/O card. MP configuration must be done from an ASCII console. NOTE The MP has a separate LAN port from the system LAN port.
System Installation Configuring the Management Processor for use with a Web Console Step 3. Access the Web console by launching a Web browser on the same subnet using the IP address for the MP LAN port. Figure 5-10 Browser Window Zoom In/Out Title Bar Step 4. Click anywhere on the Zoom In/Out title bar to generate a full screen MP window. There is not a separate administration layer when using the embedded Web access of the MP.
System Installation Configuring the Management Processor for use with a Web Console Removing Users - Users can be removed or disabled with the security options command. To remove a user, perform the following: 1. Access the MP. 2. Enter the Security Options and access control (so) command. 3. Select the second menu item then enter “D” for delete. Return the MP to default configurations - The Default Configuration (dc) command is used to reset all or some of the MP values to the default values.
System Installation Verifying Presence of the Cell Boards Verifying Presence of the Cell Boards To perform this activity, either connect to the Management Processor (MP) over the customer console or connect the CE Tool (laptop) to the RS-232 Local port on the MP. After login to the MP, verify that the MP detects the presence of all the cells installed in the server cabinet. It is important for the MP to detect the cell boards. If it does not, the partitions will not boot.
System Installation Configuring AC Line Status Configuring AC Line Status Utilities is able to detect if power is applied to each of the AC input cords for the server. This is achieved by sampling the status of the bulk power supplies. During installation, use the following procedure to check the configuration for the AC line status and configure it to match the customer’s environment. Step 1. At the MP prompt, enter cm.
System Installation Powering On the hp rp8400 Server Series Cabinet (48 V) Powering On the hp rp8400 Server Series Cabinet (48 V) After powering on the Management Processor (MP) (+3.3 V HKP), and checking that the MP detects the presence of the cell boards, power up the server cabinet, or, apply the 48 V power to the system. If using a LAN crossover cable with the laptop, review server cabinet activity for each partition configured, as the server cabinet powers up and boots.
System Installation Verifying the System Configuration Verifying the System Configuration At this point in the installation process, the hardware is set up, the Management Processor (MP) is connected to the LAN, the AC and DC power have been turned on, and the selftest is completed. Now the configuration can be verified. After DC is powered on and the selftest is completed, the BCH prompt appears (Main Menu: Enter command or menu>). 1. Enter di to display a list of the Boot Console Handler (BCH) commands.
System Installation Adding Processors with Instant Capacity On Demand (iCOD) Adding Processors with Instant Capacity On Demand (iCOD) The Instant Capacity On Demand (iCOD) program provides access to additional CPU resources beyond the amount that was purchased for the server. This provides the ability to activate additional CPU power for unexpected growth and unexpected spikes in workloads such as Internet or E-intelligence.
System Installation Booting HP-UX on the Partition(s) Booting HP-UX on the Partition(s) To boot HP-UX on a partition: 1. At the MP Main Menu, enter co. If at the BCH prompt, enter Ctrl B to return to the MP Main Menu. If at the MP CM Menu, enter ma to return to the MP Main Menu. 2. Identity the partition to boot. Partitions may be booted in any order. 3. At the BCH prompt, enter bo. The prompt, Do you wish to stop at the ISL prompt prior to booting? (y/n) appears. 4. Enter n.
6 Installation Cleanup After the hp rp8400 server series has been installed in a computer room and verified, conduct the post installation check. Before turning the system over to the customer, it is important to inspect the system visually and clean up the installation area.
Installation Cleanup Installation Cleanup Checklist Installation Cleanup Checklist Use the following list to ensure the system is ready to be turned over to the customer. • Inspect circuit boards. Check that all circuit boards are installed and properly seated, and that the circuit board retainers are reinstalled. • Inspect cabling. Check that all cables are installed, secured, and properly routed. • Inspect test points. Check that test leads are removed from the voltage test points.
7 Returning Equipment If damaged equipment is found, use the following procedure to return it to Hewlett-Packard.
Returning Equipment Repacking the Cabinet for Shipment Repacking the Cabinet for Shipment Use the original packing material to repackage the server cabinet for shipment. If the packing material is not available, contact your local Hewlett-Packard Sales and Support office regarding shipment. Before shipment, securely place a tag on the container (and equipment) to identify the owner and the service to be performed. Include the SPU cabinet model number.
A Installation Checklist This section provides a means of tracking progress to ensure that all steps required for a successful installation are completed.
Installation Checklist Using the Checklist Using the Checklist The checklist provided here is an installation aid and should be used only after you have installed a few systems using the detailed procedures described in the body of this manual. This checklist is a compilation of the tasks described in this manual. The checklist is organized as follows: PROCEDURES The procedures outlined in this document in order.
Installation Checklist Using the Checklist Table A-1 Factory-Integrated Installation Checklist (Continued) (Continued) PROCEDURE IN-PROCESS COMPLETED Unpack the peripheral cabinet (if ordered) Unpack other equipment Remove and dispose of packaging material Move cabinet(s) and equipment to computer room Move cabinets into final position Position cabinets next to each other (approx.
Installation Checklist Using the Checklist Table A-1 Factory-Integrated Installation Checklist (Continued) (Continued) PROCEDURE IN-PROCESS COMPLETED Install non-factory-integrated I/O cards (if required) Select PCI card slot Install PCI card Verify installation Route cables using the cable management arm Install other peripherals (if required) Perform visual inspection and complete installation Set up network services (if required) Enable iCOD (if available) Final inspection of circuit boards Final i
B Accessing the MP Using a Modem A modem may be used to access the Management Processor (MP) remotely. A modem is often used in conjunction with a paging device to alert a remote monitor about the condition of the SPU. As with the Local RS-232 connection, only one window can be viewed on the display device. When enabled, it provides direct access to the MP and to any partition.
Accessing the MP Using a Modem To connect the serial display device to the MP using a modem: 1. At the side of the SPU cabinet, connect one end of a modem cable to the Remote RS-232 port on the Core I/O card. Figure B-1 Remote Connection 2. Connect the other end of the RS-232 cable to the modem. 3. Connect a dedicated phone (analog) line to the modem. 4. Set modem configuration as specified for remote support.
Accessing the MP Using a Modem To modify the modem configuration to configure remote login, enter ca (Configure Asynchronous and Modem Parameters) at the MP command prompt (MP:CM>) and follow the instruction on the screen. Figure B-2 The ca Command Screen MP> cm Enter HE to get a list of available commands MP:CM> ca This command allows modification of the asychronous parameters. WARNING: Changing the asynchronous parameters requires reboot of the MP for proper local operation.
Accessing the MP Using a Modem Verifying Modem Communications Verifying Modem Communications Verify the modem communications using the following procedure: 1. If not already obtained, get the modem phone number from the customer. 2. Contact the testing organization. This could be the Response Center or the WWSIT team. 3. Provide the organization with the phone number and parameters set using the MP ca command. 4. Request confirmation of the communication link, or check the modem light for activity.
Index A ac power, 22, 47 connections, 50 input, 61 overview, 49 safety warning label check, 58 voltage check, 56 wiring and voltage checks, 51 wiring check, 51 AC power inputs A0, 61 A1, 61 B0, 61 B1, 61 accepting the equipment, 20 associated documents, 17 B BCH prompt, 77 bo (Boot) command, 80 booting HP-UX, 80 BPS (Bulk Power Supply), 67 Bulk Power Supplies BPS, 62 C ca (Configure Asychronous and Modem Parameters) command, 91 cables, checking, 82 cell board, 62 verifying presence, 75 checklist installatio
Index lists, 24 login name MP, 68 ls (LAN Status) command, 71 M MA (Main Menu) command, 78 MAC address, 70 Management Processor (MP), 64 ME (Memory) command, 78 modem, 89 MP login name, 68 password, 68 MP (Management Processor) logging in, 67 powering on, 67 MP network name, 70 N N+1 capability, 62 notational conventions, 15 notes and cautions, 13 null modem cable connectivity, 65 part number, 65 P password MP, 68 PDC Processor Dependent Code, 77 power applying cabinet, 77 cabinet switch, 77 grids, 61 house
