Drives User Guide
© Copyright 2008 Hewlett-Packard Development Company, L.P. Windows is a U.S. registered trademark of Microsoft Corporation. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Table of contents 1 Handling drives 2 Using an optical drive (select models only) Identifying the installed optical drive ..................................................................................................... 2 Using optical discs (CDs and DVDs) .................................................................................................... 3 Selecting the right disc .........................................................................................................................
The optical disc tray does not open for removal of a CD or DVD ....................................................... 30 The computer does not detect the optical drive ................................................................................. 30 A disc does not play ........................................................................................................................... 32 A disc does not play automatically ...........................................................................
1 Handling drives Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply. CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information, observe these precautions: Before you move a computer that is connected to an external hard drive, initiate Sleep and allow the screen to clear, or properly disconnect the external hard drive.
2 Using an optical drive (select models only) Your computer includes an optical drive that expands the functionality of the computer. Identify what kind of device is installed in your computer to see its capabilities. The optical drive allows you to read data discs, play music, and watch movies. Identifying the installed optical drive ▲ Select Start > Computer. You will see a list of all the devices installed on your computer, including your optical drive.
Using optical discs (CDs and DVDs) An optical drive, such as a DVD-ROM drive, supports optical discs (CDs and DVDs). These discs store information, such as music, photos, and movies. DVDs have a higher storage capacity than CDs. Your optical drive can read standard CD and DVD discs. NOTE: Some of the optical drives listed may not be supported by your computer. The listed drives are not necessarily all of the supported optical drives.
Selecting the right disc An optical drive supports optical discs (CDs and DVDs). CDs, used to store digital data, are also used for commercial audio recordings and are convenient for your personal storage needs. DVDs are used primarily for movies, software, and data backup purposes. DVDs are the same form factor as CDs but have at least 8 times the storage capacity. NOTE: The optical drive on your computer may not support all the types of optical discs discussed in this section.
Playing a CD or DVD 1. Turn on the computer. 2. Press the release button (1) on the drive bezel to release the disc tray. 3. Pull out the tray (2). 4. Hold the disc by the edges to avoid touching the flat surfaces and position the disc label-side up over the tray spindle. NOTE: If the tray is not fully accessible, tilt the disc carefully to position it over the spindle. 5. Gently press the disc (3) down onto the tray spindle until the disc snaps into place. 6. Close the disc tray.
Configuring AutoPlay 1. Select Start > Control Panel > Play CDs or other media automatically. 2. Confirm that the Use AutoPlay for all media and devices check box is selected. 3. Click Choose a default, and then select one of the available options for each media type listed. NOTE: Choose WinDVD to play DVDs. 4. Click Save. NOTE: For more information about AutoPlay, refer to Help and Support.
Changing DVD region settings Most DVDs that contain copyrighted files also contain region codes. The region codes help protect copyrights internationally. You can play a DVD containing a region code only if the region code on the DVD matches the region setting on your DVD drive. CAUTION: The region settings on your DVD drive can be changed only 5 times. The region setting you select the fifth time becomes the permanent region setting on the DVD drive.
Observing the copyright warning It is a criminal offense, under applicable copyright laws, to make unauthorized copies of copyrightprotected material, including computer programs, films, broadcasts, and sound recordings. Do not use this computer for such purposes. CAUTION: To prevent loss of information or damage to a disc, observe the following guidelines: Before writing to a disc, connect the computer to a reliable external power source.
Copying a CD or DVD 1. Select Start > All Programs > Roxio > Creator Business. 2. In the right pane, click Copy Disc. 3. Insert the disc you want to copy into the optical drive. 4. Click Copy at the bottom right of the screen. Creator Business reads the source disc and copies the data to a temporary folder on your hard drive. 5. When prompted, remove the source disc from the optical drive and insert a blank disc into the drive.
Creating or “burning” a CD or DVD CAUTION: Observe the copyright warning. It is a criminal offense, under applicable copyright laws, to make unauthorized copies of copyright-protected material, including computer programs, films, broadcasts, and sound recordings. Do not use this computer for such purposes. If your computer includes a DVD±RW optical drive, you can use software such as Windows® Media Player or Roxio Creator Business to burn data and audio files, including MP3 and WAV music files.
Removing an optical disc (CD or DVD) 1. Press the release button (1) on the drive bezel to release the disc tray, and then gently pull out the tray (2) until it stops. 2. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces. NOTE: If the tray is not fully accessible, tilt the disc carefully as you remove it. 3. Close the disc tray and place the disc in a protective case.
3 Using external drives Removable external drives expand your options for storing and accessing information. A USB drive can be added by connecting the drive to a USB port on the computer or on an optional docking device. USB drives include the following types: ● 1.
4 Using HP 3D DriveGuard HP 3D DriveGuard protects the hard drive by parking the drive and halting I/O requests under either of the following conditions: ● You drop the computer. ● You move the computer with the display closed while the computer is running on battery power. A short time after the end of one of these events, HP 3D DriveGuard returns the hard drive to normal operation.
Identifying HP 3D DriveGuard status The drive light on the computer changes to an amber color to show that the drive is parked. To determine whether drives are currently protected or whether a drive is parked, select Start > Control Panel > Mobile PC > Windows Mobility Center: ● If the software is enabled, a green check mark is superimposed over the hard drive icon. ● If the software is disabled, a red X is superimposed over the hard drive icon.
Using HP 3D DriveGuard software The HP 3D DriveGuard software enables you to perform the following tasks: ● Enable and disable HP 3D DriveGuard. NOTE: Permission to enable or disable HP 3D DriveGuard is dependent on certain user privileges. Members of an Administrator group can change privileges for non-Administrator users. ● Determine whether a drive in the system is supported. To open the software and change settings, follow these steps: 1.
5 Improving hard drive performance Using Disk Defragmenter As you use the computer, files on the hard drive become fragmented. Disk Defragmenter consolidates the fragmented files and folders on the hard drive so that the system can run more efficiently. After you start Disk Defragmenter, it works without supervision. Depending on the size of your hard drive and the number of fragmented files, Disk Defragmenter may take more than an hour to complete.
6 Replacing a hard drive Your computer is equipped with either a 1.8-inch hard drive or a 2.5-inch hard drive. The replacement procedures vary, depending on computer model. CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation.
Replacing a 1.8-inch hard drive To remove a 1.8-inch hard drive: 1. Save your work. 2. Shut down the computer and close the display. 3. Disconnect all external hardware devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5. Turn the computer upside down on a flat surface, with the hard drive bay toward you. 6. Remove the battery from the computer. 7. Loosen the 2 hard drive cover screws (1). 8. Lift the hard drive cover away from the computer (2). 9.
11. Remove the hard drive screw (3). 12. Tilt the hard drive away from the hard drive bay (1). 13. Lift the hard drive out of the hard drive bay (2). Replacing a 1.
14. Gently disconnect hard drive cable from the hard drive. To install a 1.8-inch hard drive: 20 1. Insert the hard drive cable into the hard drive cable connector and press in gently until the cable is firmly seated. 2. Insert the hard drive into the hard drive bay (1).
3. Tilt the hard drive down until it is firmly seated (2). 4. Replace the hard drive retention bracket (1). 5. Replace the hard drive retention bracket screws (2). 6. Replace the hard drive screw (3). 7. Align the tabs (1) on the hard drive cover with the notches on the computer. 8. Replace the cover (2). Replacing a 1.
9. Tighten the hard drive cover screws (3). 10. Reinstall the battery. 11. Turn the computer right-side up, and then reconnect external power and external devices. 12. Turn on the computer.
Replacing a 2.5-inch hard drive To replace a 2.5-inch hard drive: 1. Save your work. 2. Shut down the computer and close the display. 3. Disconnect all external hardware devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5. Turn the computer upside down on a flat surface, with the hard drive bay toward you. 6. Remove the battery from the computer. 7. Remove the 6 keyboard access screws. 8. Remove the 4 hard drive screws. 9.
10. Carefully slide the switch cover to the right (1) to release the switch cover hooks, and then lift the switch cover away from the keyboard (2). 11. Carefully lift the top edge of the keyboard and tilt the keyboard over until it rests on the palm rest of the computer. NOTE: If the left side of the keyboard releases before the right side, pull the keyboard slightly to the left to release the right side.
12. Gently disconnect the USB cable from the USB connector. 13. Remove the hard drive from the hard drive bay. NOTE: Be sure that the USB cable is free from obstructions as you remove the hard drive. Replacing a 2.
To install a 2.5-inch hard drive: 1. Insert the hard drive into the hard drive bay until it is firmly seated. NOTE: As you insert the drive, be sure that the USB cable is tucked into the hard drive cage and is free from obstructions. 2. 26 Insert the USB cable into USB cable connector, and press in gently until the cable is firmly seated.
3. Replace the keyboard. 4. Press down on the 4 switch cover locations (1) making sure that the switch cover hooks are engaged, and then slide the switch cover to the left (2). NOTE: If there are bumps or raised areas on the switch cover, remove the switch cover and repeat this step. 5. Turn the computer upside down on a flat surface. Replacing a 2.
6. Replace the 4 hard drive screws. 7. Replace the 6 keyboard access screws. 8. Replace the battery. 9. Turn the computer right-side up, and then reconnect external power and external devices. 10. Turn on the computer.
7 Troubleshooting The following sections describe several common issues and resolutions.
The optical disc tray does not open for removal of a CD or DVD 1. Insert the end of a paper clip (1) into the release access in the front bezel of the drive. 2. Press in gently on the paper clip until the tray is released, and then pull out the tray (2) until it stops. 3. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
● Scan for hardware changes. Windows scans your system for installed hardware and installs any required drivers. ● Click Properties to see if the device is working properly: ◦ Click Troubleshoot to fix problems. ◦ Click the Driver tab to update, disable, or uninstall drivers for this device.
A disc does not play ● Save your work and close all open programs before playing a CD or DVD. ● Log off the Internet before playing a CD or DVD. ● Be sure that you insert the disc properly. ● Be sure that the disc is clean. If necessary, clean the disc with filtered water and a lint-free cloth. Wipe from the center of the disc to the outer edge. ● Check the disc for scratches. If you find scratches, treat the disc with an optical disc repair kit available at many electronics stores.
A disc does not play automatically 1. Select Start > Control Panel > Play CDs or other media automatically. 2. Confirm that the Use AutoPlay for all media and devices check box is selected. 3. Click Save. A CD or DVD should now start automatically when it is inserted into the optical drive.
The process of burning a disc does not begin, or it stops before completion 34 ● Be sure that all other programs are closed. ● Turn off Sleep mode and Hibernation. ● Be sure that you are using the right kind of disc for your drive. See your user guides for more information about disc types. ● Be sure that the disc is inserted properly. ● Select a slower write speed and try again.
A device driver must be reinstalled To reinstall a device driver, follow these steps: 1. Remove any discs from the optical drive. 2. Click Start and type device manager in the Start Search box. As you type, search results are listed in the pane above the box. 3. In the results pane, click Device Manager. If prompted by User Account Control, click Continue. 4.
To use HP Update: 1. Select Start > All Programs > HP > HP Update. 2. On the HP Welcome screen, click Settings, and then select a time when the utility should check for software updates on the Web. 3. Click Next to immediately check for HP software updates. To use the HP Web site: 36 1. Open your Internet browser, and go to http://www.hp.com/support. 2. Select your country or region. 3.
Index A airport security devices 1 AutoPlay 6 C CD burning 10 copying 9 playing 5 removing 11 CD drive 2, 12 copyright warning 8 D device drivers HP 35 Microsoft 35 reinstalling 35 Disk Cleanup software 16 Disk Defragmenter software 16 disk performance 16 diskette drive 12 drive light 14 drives caring for 1 diskette 12 DVD ROM Drive 3 DVD±RW SuperMulti DL Drive 3 external 12 hard 12, 17, 20 optical 2, 12 See also hard drive; optical drive DVD burning 10 changing region setting 7 copying 9 playing 5 remov
