Memory Modules User Guide
© Copyright 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Table of contents Adding or replacing memory modules Adding or replacing a memory module in the expansion memory module slot .................................... 2 Upgrading a memory module in the primary memory module slot ....................................................... 5 Index ...................................................................................................................................................................
iv
Adding or replacing memory modules The computer has two memory module compartments. The primary memory module compartment is located under the keyboard. The expansion memory module compartment is located on the bottom of the computer. The memory capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot.
Adding or replacing a memory module in the expansion memory module slot To add or replace a memory module in the expansion memory module slot, follow these steps: 1. Save your work. 2. Shut down the computer and close the display. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. 3. Disconnect all external devices connected to the computer. 4.
b. Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot. To protect a memory module after removal, place it in an electrostatic-safe container. 10. Insert a memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module, and do not bend the memory module. a. Align the notched edge (1) of the memory module with the tab in the memory module slot. b.
13. Tighten the memory module compartment cover screw (3). 14. Replace the battery. 15. Turn the computer right-side up, and then reconnect external power and external devices. 16. Turn on the computer.
Upgrading a memory module in the primary memory module slot To upgrade a memory module in the primary memory module slot, follow these steps: 1. Save your work. 2. Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. 3. Disconnect all external devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5.
. Carefully lift the top edge of the keyboard and tilt the keyboard over until it rests on the palm rest of the computer. NOTE: If the left side of the keyboard releases before the right side, pull the keyboard slightly to the left to release the right side. 11. Remove the memory module compartment cover screw (1). 12. Lift the memory module compartment cover (2). 13. Remove the memory module: a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up.
b. Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot. To protect a memory module after removal, place it in an electrostatic-safe container. 14. Insert a memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module, and do not bend the memory module. a. Align the notched edge (1) of the memory module with the tab in the memory module slot. b.
16. Replace the memory module compartment cover screw (2). 17. Replace the keyboard.
18. Press down on the 4 switch cover locations (1) making sure that the switch cover hooks are engaged, and then slide the switch cover to the left (2). NOTE: If there are bumps or raised areas on the switch cover, remove the switch cover and repeat this step. 19. Turn the computer upside down on a flat surface. 20. Replace the keyboard access screws. 21. Replace the battery. 22. Turn the computer right-side up, and then reconnect external power and external devices. 23. Turn on the computer.
Index K keyboard screws removing 5 replacing 9 M memory module inserting 7 removing 2, 6 replacing 2, 5 upgrading primary 5 memory module compartment cover removing 2 replacing 3 memory, replacing memory modules 2, 5 10 Index
