Getting Started HP Notebook
© Copyright 2011 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ..................................................................................................................... 4 Top ....................
Using keypads ................................................................................................................... 24 Using the embedded numeric keypad ............................................................... 24 Turning the embedded numeric keypad on and off .......................... 25 Switching key functions on the embedded numeric keypad ............. 25 Using an optional external numeric keypad ...................................................... 25 Using pointing devices ......
Backup and recovery .................................................................................................................................... 50 Windows 7 .......................................................................................................................................... 50 Backing up your information .............................................................................................. 50 Performing a system recovery ...............................................
viii
1 Welcome ● Finding information After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, refer to Networking on page 16. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer and includes a limited subscription for free updates.
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about Quick Setup poster ● How to set up the computer ● Help to identify computer components Getting Started guide ● Computer features To access this guide: ● How to connect to a wireless network Select Start > Help and Support > User Guides.
Resources For information about Safety & Comfort Guide ● Proper workstation setup, posture, health, and work habits To access this guide: ● Electrical and mechanical safety information Select Start > Help and Support > User Guides. – or – Select Start > All Programs > HP > HP Documentation. – or – Go to http://www.hp.com/ergo. Worldwide Telephone Numbers booklet HP support telephone numbers This booklet is provided with your computer.
2 Getting to know your computer ● Top ● Front ● Right ● Left ● Display ● Rear ● Bottom Top TouchPad Component 4 Description (1) Pointing stick (select models only) Moves the pointer and selects or activates items on the screen. (2) Left pointing stick button (select models only) Can be used with the pointing stick and functions like the left button on an external mouse. (3) TouchPad on/off button Turns the TouchPad on and off.
Component (4) Description TouchPad Moves the pointer and selects or activates items on the screen. NOTE: Vertical scrolling is supported on the right edge of the TouchPad. (5) Left TouchPad button Functions like the left button on an external mouse. (6) Right pointing stick button (select models only) Can be used with the pointing stick and functions like the right button on an external mouse. (7) Right TouchPad button Functions like the right button on an external mouse.
Component (5) Description QuickWeb light ● On: The computer is on. ● Off: The computer is off or in Hibernation. NOTE: For more information, refer to “HP QuickWeb” in this guide and to the HP Quickweb software Help (6) (7) 6 Mute light Num lock light Chapter 2 Getting to know your computer ● Amber: Computer sound is off. ● Off: Computer sound is on. On: Num lock is on.
Buttons and fingerprint reader Component Description (1) TouchPad on/off button Turns the TouchPad on and off. (2) Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component (4) Description QuickWeb button ● When the computer is off or in Hibernation, press the button to open HP QuickWeb. ● When the computer is in Microsoft Windows, press the button to open the default Web browser. ● When the computer is in HP QuickWeb, press the button to open the default Web browser. NOTE: For more information, refer to “HP QuickWeb” in this guide and to the HP QuickWeb software Help.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) Function keys Execute frequently used system functions when pressed in combination with the fn key. (3) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (4) Start key Displays the Start menu. (5) Menu key Displays the active program’s shortcut menu (same as right-click menu).
Front Component Description (1) Display release latch Opens the computer. (2) Wireless light ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off. ● On: The computer is on. ● Blinking: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. ● Amber: The computer is connected to external power and the battery is charged from 0 – 90%.
Right Component (1) Description Audio-out (headphone) jack Produces sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio. NOTE: When a device is connected to the headphone jack, the computer speakers are disabled. (2) Audio-in (microphone) jack Connects an optional computer headset microphone, stereo array microphone, or monaural microphone. (3) 1394 port Connects an optional IEEE 1394 or 1394a device, such as a camcorder.
Left Component (1) Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. 12 (2) RJ-45 (network) jack Connects a network cable. (3) USB ports (2) Connect optional USB devices. (4) ExpressCard slot or Smart Card reader slot (depending on configuration) Supports optional ExpressCards or Smart Cards.
Display Component Description (1) Turns off the display or initiates Sleep if the display is closed while the power is on. Internal display switch NOTE: The display switch is not visible from the outside of the computer. (2) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (3) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide-area networks (WWAN).
Rear Component Description Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Bottom Component Description (1) Battery release latch Releases the battery from the battery bay. (2) Docking connector Connects an optional docking device. (3) Bottom cover release latch Releases or locks the bottom cover. (4) SIM slot Contains a wireless subscriber identity module (SIM). The SIM slot is located inside the battery bay. (5) Battery bay Holds the battery. (6) Accessory battery connector Connects an optional accessory battery.
3 Networking ● Using an Internet service provider (ISP) ● Connecting to a wireless network NOTE: Internet hardware and software features vary depending on computer model and your location. Your computer may support one or both of the following types of Internet access: 16 ● Wireless—For mobile Internet access, you can use a wireless connection. Refer to Connecting to an existing WLAN on page 18 or Setting up a new WLAN network on page 18.
Using an Internet service provider (ISP) Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service. NOTE: Your ISP will give you a user ID and password to access the Internet. Record this information and store it in a safe place.
Connecting to an existing WLAN 1. Turn on the computer. 2. Be sure that the WLAN device is on. 3. Click the network icon in the notification area, at the far right of the taskbar. 4. Select a network to connect to. 5. Click Connect. 6. If required, enter the security key.
Configuring a wireless router For help in setting up a WLAN, refer to the information provided by your router manufacturer or your ISP. The Windows operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network: ● Windows 7—Select Start > Control Panel > Network and Internet > Network and Sharing Center > Set up a new connection or network > Set up a network. Then follow the on-screen instructions.
4 HP QuickWeb Getting started The HP QuickWeb environment provides a fun and engaging way to perform many of your favorite activities. Your computer is ready to go within seconds of turning it on, allowing you to rapidly access the Internet, widgets, and communication programs. Simply press the QuickWeb button on your computer, and then start browsing the Internet, communicating with Skype, and exploring other HP QuickWeb programs.
Starting HP QuickWeb ● To start HP QuickWeb, press the QuickWeb button when the computer is off or in Hibernation. The following table explains the different behaviors of the QuickWeb button. Button Bahavior QuickWeb button ● When the computer is off or in Hibernation, opens HP QuickWeb. ● When the computer is in Microsoft Windows, opens the default Web browser. ● When the computer is in HP QuickWeb, opens the default Web browser.
5 22 Keyboard and pointing devices ● Using the keyboard ● Using pointing devices Chapter 5 Keyboard and pointing devices
Using the keyboard Identifying the hotkeys A hotkey is a combination of the fn key (1) and either the esc key (2) or one of the function keys (3). To use a hotkey: ▲ Briefly press the fn key, and then briefly press the second key of the hotkey combination. Hotkey combination Description fn+esc Displays system information. fn+f3 Initiates Sleep, which saves your information in system. The display and other system components turn off and power is conserved.
Hotkey combination Description fn+f8 Displays charge information for all installed batteries. The display indicates which batteries are charging and reports the amount of charge remaining in each battery. fn+f9 Decreases the screen brightness level. fn+f10 Increases the screen brightness level. Using keypads The computer includes an embedded numeric keypad. The computer also supports an optional external numeric keypad or an optional external keyboard that includes a numeric keypad.
Turning the embedded numeric keypad on and off Press fn+num lk to turn on the embedded numeric keypad. Press fn+num lk again to turn off the keypad. NOTE: The embedded numeric keypad is turned off while an external keyboard or numeric keypad is connected to the computer.
Using the pointing stick Press the pointing stick in the direction you want to move the pointer on the screen. Use the left and right pointing stick buttons as you would the left and right buttons on an external mouse. Using the TouchPad To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go. Use the left and right TouchPad buttons like the buttons on an external mouse.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off light. NOTE: The TouchPad on/off light is off when the TouchPad is on. Navigating To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
Selecting Use the left and right TouchPad buttons like the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To view the demonstration of a gesture: 1. Right-click the Synaptics icon in the notification area, at the far right of the taskbar, and then click TouchPad Properties. 2.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. NOTE: Two-finger scrolling is enabled at the factory. Pinching/Zooming Pinching allows you to zoom in or out on images or text. ● Zoom in by placing two fingers together on the TouchPad, and then moving them apart.
Rotating Rotating allows you to rotate items such as photos. To rotate, anchor your left forefinger in the TouchPad zone. Move the right forefinger around the anchored finger in a sweeping motion, moving from 12 o’clock to 3 o’clock. To reverse the rotation, move your right forefinger from 3 o’clock to 12 o’clock. 30 NOTE: Rotating must be done within the TouchPad zone. NOTE: Rotating is disabled at the factory.
6 Maintenance ● Inserting or removing the battery ● Removing or replacing the bottom cover ● Replacing or upgrading the hard drive ● Replacing a drive in the upgrade bay ● Adding or replacing memory modules ● Updating programs and drivers ● Using SoftPaq Download Manager ● Cleaning your computer Inserting or removing the battery NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide. To insert the battery: 1.
To remove the battery: CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and initiate Hibernation or shut down the computer through Windows before removing the battery. 32 1. Turn the computer upside down on a flat surface, with the battery bay toward you. 2. Slide the battery release latch (1) to release the battery. 3. Remove the battery from the computer (2).
Removing or replacing the bottom cover CAUTION: To prevent information loss or an unresponsive system: Save your work and shut down the computer before adding or replacing a memory module or hard drive. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
3. Slide the bottom cover towards the battery bay until the bottom cover snaps into place. 4. With the battery bay toward you, slide the bottom cover release latch to the left (3), and if you choose to, insert and tighten the optional screw (4) to hold the bottom cover in place. Slide the release latch to the right to lock the bottom cover (5). NOTE: If you want to use the optional screw, it is stored inside the bottom cover. 5. 34 Insert the battery (see Inserting or removing the battery on page 31).
Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. Removing the hard drive To remove the hard drive: 1.
3. Tighten the hard drive screws (4). 4. Replace the bottom cover (see Replacing the bottom cover on page 33). 5. Insert the battery (see Inserting or removing the battery on page 31). 6. Connect AC power and external devices to the computer. 7. Turn on the computer. Replacing a drive in the upgrade bay The upgrade bay can hold either a hard drive or an optical drive.
8. Remove the hard drive screws from the upgrade bay. 9. Loosen the upgrade bay screw (1). 10. Using a flat-bladed screwdriver, gently push the tab to release the hard drive (2). 11. Remove the hard drive from the upgrade bay (3).
To install a hard drive in the upgrade bay: 1. Insert the hard drive (1) into the upgrade bay, and then tighten the upgrade bay screw (2). 2. Replace the hard drive screws. 3. Replace the bottom cover (see Replacing the bottom cover on page 33). 4. Insert the battery (see Inserting or removing the battery on page 31). 5. Turn the computer right-side up, and then reconnect AC power and external devices to the computer. 6. Turn on the computer.
To remove an optical drive from the upgrade bay: 1. Save your work. 2. Shut down the computer and close the display. 3. Disconnect all external hardware devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5. Turn the computer upside down on a flat surface, with the upgrade bay toward you. 6. Remove the battery (see Inserting or removing the battery on page 31). 7. Remove the bottom cover (see Removing the bottom cover on page 33). 8.
40 2. Tighten the upgrade bay screw (2). 3. Replace the bottom cover (see Replacing the bottom cover on page 33). 4. Insert the battery (see Inserting or removing the battery on page 31). 5. Turn the computer right-side up, and then reconnect AC power and external devices to the computer. 6. Turn on the computer.
Adding or replacing memory modules The computer has two memory module compartments. One memory module compartment is located underneath the keyboard and the other is located underneath the bottom cover. The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 6. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
8. Insert the battery (see Inserting or removing the battery on page 31). 9. Connect AC power and external devices to the computer. 10. Turn on the computer. Adding or replacing the primary memory module underneath the keyboard CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before adding or replacing memory modules. Do not remove a memory module while the computer is on, in the Sleep state, or in Hibernation.
c. Turn the computer right-side up, lift the top edge of the keyboard, and then rest the keyboard on the TouchPad. NOTE: Do not disconnect the keyboard cable. 6. If you are replacing a memory module, remove the existing memory module: a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up. b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot.
7. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. a. Align the notched edge (1) of the memory module with the tab in the memory module slot. b. With the memory module at a 45-degree angle from the surface of the memory module compartment, press the module (2) into the memory module slot until it is seated. c.
9. c. Press gently on the keyboard (3) so that it snaps in place. d. Turn the computer upside down, and then tighten the keyboard screws (4) to lock the keyboard into place. Replace the bottom cover (see Replacing the bottom cover on page 33). 10. Insert the battery (see Inserting or removing the battery on page 31). 11. Connect AC power and external devices to the computer. 12. Turn on the computer.
Updating programs and drivers HP recommends that you update your programs and drivers on a regular basis with the latest versions. Go to http://www.hp.com/support to download the latest versions. You can also register to receive automatic update notifications when they become available. Using SoftPaq Download Manager HP SoftPaq Download Manager (SDM) is a tool that provides quick access to SoftPaq information for HP business computers without requiring the SoftPaq number.
Cleaning your computer ● Cleaning products ● Cleaning procedures Cleaning products Use the following products to safely clean and disinfect your notebook or tablet PC: ● Dimethyl benzyl ammonium chloride 0.3 percent maximum concentration (For example: germicidal disposable wipes. These wipes come in a variety of brand names.
Cleaning the TouchPad and keyboard CAUTION: When cleaning the TouchPad and keyboard, do not let liquids drip between the keys. This can permanently damage internal components. ● To clean and disinfect the TouchPad and keyboard, use a soft microfiber cloth or chamois moistened with one of the cleaning solutions listed previously or use an acceptable germicidal disposable wipe.
7 Backup and recovery Windows 7 ● Backing up your information ● Performing a system recovery To protect your information, use Windows Backup and Restore to back up individual files and folders, back up your entire hard drive (select models only), create system repair discs (select models only) by using the installed optical drive (select models only) or an optional external optical drive, or create system restore points.
new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. The system repair discs (select models only) are used to start up (boot) the computer and repair the operating system in case of system instability or failure. Your initial and subsequent backups allow you to restore your data and settings if a failure occurs. You can back up your information to an optional external hard drive, a network drive, or discs.
Using the Windows recovery tools To recover information you previously backed up: 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to recover your system settings, your computer (select models only), or your files. To recover your information using Startup Repair, follow these steps: CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive.
3. If the HP Recovery partition is listed, restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 4. Press f11 while the “Press for recovery” message is displayed on the screen. 5. Follow the on-screen instructions. Using a Windows 7 operating system DVD (purchased separately) To order a Windows 7 operating system DVD, go to http://www.hp.
Windows Vista To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
To create a backup using Backup and Restore Center: NOTE: Be sure that the computer is connected to AC power before you start the backup process. NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore Center. 2. Follow the on-screen instructions to back up your entire computer (select models only) or your files.
4. Select Repair your computer. 5. Follow the on-screen instructions. NOTE: For additional information on recovering information using the Windows tools, perform a search for these topics in Help and Support. Using f11 recovery tools CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed.
Using a Windows Vista operating system DVD (purchased separately) To order a Windows Vista operating system DVD, go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. You can also order the DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet included with the computer. CAUTION: Using a Windows Vista operating system DVD completely erases hard drive contents and reformats the hard drive.
8 58 Customer support ● Contacting customer support ● Labels Chapter 8 Customer support
Contacting customer support If the information provided in this user guide, in the HP Notebook Reference Guide, or in Help and Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support. The serial number label is affixed to the bottom of the computer.
9 Specifications ● Input power ● Operating environment 61
Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
Operating environment Factor Metric U.S.
Index Symbols/Numerics 1394 port, identifying 11 A accessory battery connector, identifying 15 audio-in (microphone) jack 11 audio-out (headphone) jack 11 B Backup and Restore 51 Backup and Restore Center 54, 55 battery bay 15, 60 battery light 10 battery release latch 15 battery, replacing 31 Bluetooth compartment, identifying 15 Bluetooth label 60 bottom cover, removing or replacing 33 buttons left pointing stick button 4 left TouchPad 5 optical drive eject 12 power 7 QuickWeb 8 right pointing stick bu
function 9 menu 9 num lk 9 start 9 L labels Bluetooth 60 HP Mobile Broadband Module 60 Microsoft Certificate of Authenticity 60 regulatory 60 serial number 60 SIM 60 wireless certification 60 WLAN 60 latch, battery release 15 lights battery 10 caps lock 5 hard drive 10 HP QuickWeb 6 mute 6 num lock 6 power 5, 10 webcam 13 wireless 5, 10 M memory module inserting 42, 45 removing 41, 44 replacing 41 memory module compartment, identifying 15 menu key, identifying 9 Microsoft Certificate of Authenticity label 6
wireless lights 5, 10 wireless network (WLAN), equipment needed 18 wireless network, connecting 17 wireless router, configuring 19 wireless set up 18 wireless, identifying 15 WLAN connecting 18 protecting 19 WLAN antennas, identifying 13 WLAN device 60 WLAN label 60 WWAN antennas, identifying 13 Z zooming TouchPad gesture 66 Index 29