HSG80 ACS Solution Software Version 8.7 for Compaq Tru64 UNIX Installation and Configuration Guide
Table Of Contents
- HSG80 ACS Solution Software Version 8.7 for Compaq Tru64 UNIX Installation and Configuration Guide
- About this Guide
- 1- Planning a Subsystem
- Defining Subsystems
- What is Failover Mode?
- Selecting a Cache Mode
- Enabling Mirrored Caching
- What is the Command Console LUN?
- Determining Connections
- Assigning Unit Numbers
- What is Selective Storage Presentation?
- 2- Planning Storage Configurations
- Where to Start
- Determining Storage Requirements
- Configuration Rules for the Controller
- Addressing Conventions for Device PTL
- Choosing a Container Type
- Creating a Storageset Profile
- Planning Considerations for Storageset
- Changing Characteristics through Switches
- Specifying Storageset and Partition Switches
- Specifying Initialization Switches
- Specifying Unit Switches
- Creating Storage Maps
- 3- Preparing the Host System
- Installing RAID Array Storage System
- Making a Physical Connection
- Preparing LUNs for Access by Tru64 UNIX FileSystem
- DECsafe Available Server Environment (ASE)
- HSG80 Units and Tru64 UNIX Utilities
- Solution Software Upgrade Procedures
- New Features, ACS 8.7 for Tru64
- 4- Installing and Configuring HSG Agent
- 5- FC Configuration Procedures
- Establishing a Local Connection
- Setting Up a Single Controller
- Setting Up a Controller Pair
- Configuring Devices
- Configuring Storage Containers
- Assigning Unit Numbers and Unit Qualifiers
- Configuration Options
- Verifying Storage Configuration from Host
- 6- Using CLI for Configuration
- 7- Backing Up, Cloning, and Moving Data
- A- Subsystem Profile Templates
- Storageset Profile
- Storage Map Template 1 for the BA370 Enclosure
- Storage Map Template 2 for the second BA370 Enclosure
- Storage Map Template 3 for the third BA370 Enclosure
- Storage Map Template 4 for the Model 4214R Disk Enclosure
- Storage Map Template 5 for the Model 4254 Disk Enclosure
- Storage Map Template 6 for the Model 4310R Disk Enclosure
- Storage Map Template 7 for the Model 4350R Disk Enclosure
- Storage Map Template 8 for the Model 4314R Disk Enclosure
- Storage Map Template 9 for the Model 4354R Disk Enclosure
- B- Installing, Configuring, and Removing the Client
- C- SWCC Agent in TruCluster Environment
- SWCC Overview
- Running the SWCC Agent on a V4.0G Cluster
- Running the SWCC Agent under ASE Services
- Running the SWCC Agent on a V5.x Cluster
- Problems with Running the Agent on Multiple Clusters
- Configure the Controller
- Use Multiple-Bus Failover Mode
- Verify That the HSG80/HSG60 Unit Offsets Are Zero
- Install and Run the Agent on One Cluster Member
- Example of Installing the Agent on a Cluster Member
- Create the CAA Action Script
- Create the CAA Resource
- Glossary
- Index
Installing and Configuring HSG Agent
4–3HSG80 ACS Solution Software Version 8.7 for Compaq Tru64 UNIX Installation and
Configuration Guide
4–3
About the Network Connection for the Agent
The network connection, shown in Figure 4–1, displays the subsystem connected to a
hub or a switch. SWCC can consist of any number of Clients and Agents in a network.
However, it is suggested that you install only one Agent on a computer.
By using a network connection, you can configure and monitor the subsystem from
anywhere on the LAN. If you have a WAN or a connection to the Internet, monitor the
subsystem with TCP/IP.
IMPORTANT: SWCC does not support the dynamic host configuration protocol (DHCP) or the
Windows Internet Name Service (WINS).
3 Verify that there is a LUN for communications. This can be either the
CCL or a LUN that was created with the CLI. See “What is the
Command Console LUN?” on page 1–11 in Chapter 1.
4 Install the Agent (TCP/IP network connections) on a system connected
to the HSG80 controller. See Chapter 3 for agent installation.
5 Add the name of the Client system to the Agent’s list of Client system
entries (TCP/IP network connections). This can be done during
installation or when reconfiguring the Agent.
6 Install the Client software on Windows 2000 with Service Pack 2 or 3 or
Windows NT 4.0 with Service Pack 6A. See Appendix B.
7 Add the name of the Agent system to the Navigation Tree of each Client
system that is on the Agent’s list of Client system entries (TCP/IP
network connections). See Appendix B.
8 Set up pager notification (TCP/IP network connections). Refer to
“Setting Up Pager Notification” in the StorageWorks Command Console
Version 2.5, User Guide.
Table 4–2: Installation and Configuration Overview (Continued)
Step Procedure