HP DesignJet T1700 Printer Series - Assembly instructions

ManualsBrandsHP ManualsDesktopsHP DesignJet T1700 44-in Printer

Large Format Division

Camí de Can Graells 1-21 · 08174

Sant Cugat del Vallès

Barcelona · Spain

HP DesignJet T1700

Printer Series

Assembly instructions

Instructions d’assemblage

Anleitung zum Zusammenbau

Istruzioni per l’installazione

Instrucciones de montaje

Instruções de montagem

Instructies voor het opstellen



*W6B56-90004*

W6B56-90004

Hardware Setup:

1- Assemble the stand

2- Attach the printer body to the stand assembly

3- Set up the printer

4- Printhead and cartridge setup

5- Connectivity & Mobile Printing

Software setup:

Now, it’s easy to print large-format documents from virtually anywhere,

using your laptop, printer touchscreen, iPhone®, or iPad®.

Install the product software from www.hp.com/go/T1700/drivers

Installation du matériel :

1- Assemblage du support

2- Fixation de l’imprimante au support

3- Conguration de l’imprimante

4- Installation des têtes d’impression et des cartouches

5- Connectivité et impression mobile

Installation du logiciel :

Il est désormais facile d’imprimer des documents grand format depuis

quasiment n’importe où à l’aide d’un ordinateur portable, de l’écran tactile

de l’imprimante, d’un iPhone® ou d’un iPad®.

Installation du logiciel du produit à partir dewww.hp.com/go/T1700/drivers

Hardware-Setup:

1- Zusammenbauen des Standfußes

2- Aufsetzen des Druckers auf den

Standfuß

3-Einrichten des Druckers

4- Einrichten von Druckköpfen und Patronen

5- Verbindung und HP Mobile Printing

Software-Setup:

Das Drucken großformatiger Dokumente von nahezu jedem Standort aus

mit Ihrem Notebook, Drucker-Touchscreen,

iPhone® oder iPad® ist nun einfacher denn je.

Installieren Sie die Produktsoftware von: www.hp.com/go/T1700/drivers

Installazione dell’hardware:

1- Assemblaggio del piedistallo

2- Fissare il corpo della

stampante al piedistallo

3-Installazione della stampante

4 - Installazione delle cartucce e delle testine di stampa

5- Connettività e soluzioni “mobili” per la stampa

Impostazione del software:

Ora è semplice stampare documenti di grande formato da praticamente

qualsiasi posizione utilizzando il laptop, lo schermo a soramento della

stampante, l’iPhone® o l’iPad®.

Installare il software del prodotto da: www.hp.com/go/T1700/drivers

Instalación del hardware:

1- Montaje del soporte

2- Una la estructura de la impresora al conjunto del soporte

3-Con iguración de la impresora.

4- Instalación del cabezal de impresión y el cartucho

5-Conectividad e impresión desde dispositivos móviles

Instalación del software:

Ahora resulta muy fácil imprimir documentos de gran formato desde

prácticamente cualquier lugar mediante un portátil, la pantalla táctil de

la impresora, un iPhone® o un iPad®.

Instale el software del producto desde: www.hp.com/go/T1700/drivers

Conguração de hardware:

1- Monte a base

2- Conecte a impressora à

montagem da base

3- Instalar a impressora

4 - Conguração de cartucho de tinta e cabeçotes de impressão

5- Conectividade e impressão móvel

Conguração de software:

Agora, é fácil imprimir documentos em grandes formatos de

praticamente qualquer lugar usando olaptop, a tela sensível ao toque

da impressora, o iPhone® ou o iPad®.

Instale o software do produto pelo site: www.hp.com/go/T1700/drivers

Installatie van de hardware:

1- De voet in elkaar zetten

2- Bevestig het hoofdbestanddeel van de printer aan de gemonteerde

staander

3- De printer opstellen

4- Installatie van printkop en cartridge

5- Connectiviteit en mobiel afdrukken

Installatie van de software:

Nu kunt u eenvoudig documenten van groot formaat vanaf vrijwel elke

locatie af te drukken, met behulp van uw laptop,

uw printertouchscreen, iPhone® of iPad®.

Installeer de productsoftware via: www.hp.com/go/T1700/drivers























®iPhone ®iPad.

www.hp.com/go/T1700/drivers

Summary of content (28 pages)

PAGE 1
HP DesignJet T1700 Printer Series EN Hardware Setup: 1- Assemble the stand 2- Attach the printer body to the stand assembly 3- Set up the printer 4- Printhead and cartridge setup 5- Connectivity & Mobile Printing EN Assembly instructions FR Instructions d’assemblage Software setup: Now, it’s easy to print large-format documents from virtually anywhere, using your laptop, printer touchscreen, iPhone®, or iPad®. DE Anleitung zum Zusammenbau Install the product software from www.hp.
PAGE 2
1 EN Please read these instructions carefully. These assembly instructions explain how to assemble the printer. • Because the product is heavy, you may need three people to unpack it. When more than one person is needed, this symbol is displayed *. • You need a roll of 15in (381mm) minimum paper to align the printheads. • You need a LAN connection to connect the printer to the internet. Note: Roll and LAN cables are not included. • To download the printer drivers go to www.hp.com/go/T1700/drivers.
PAGE 3
EN FR DE IT ES PT NL 4 5 1 Assemble the stand Assemblage du support Zusammenbauen des Standfußes Assemblaggio del piedistallo Montaje del soporte Monte a base De voet in elkaar zetten ‫تجميع الحامل‬ AR X8 40’ EN Locate the stand pieces and remove the following: 1. Right leg / 2. Basket frame / 3. Right foot / 4. Screwdriver and screws / 5. Cross brace / 6. Left foot / 7. Left leg / 8.Cross bar. Fix one foot to a leg with 8 screws. Repeat the process for the other foot and leg.
PAGE 4
EN 8 7 6 9 Slot a leg onto the cross brace to install the leg with the long side of the foot as shown in the image. Important: Note that there are stickers on the legs, make sure the letters match the ones on the cross brace (R with R, L with L). Fix the leg to the cross brace with 3 screws at the inner face of the leg. Important: Do not fully tighten them. Slot the other leg onto the cross brace making sure that the basket supports located on the feet (1 on each foot) are on the same side.
PAGE 5
11 10 12 13 X2+2 EN Fix the cross bar to the bottom of the legs with 4 screws (2 each side) . Turn the stand upright. Attach the outside of the leg to the cross brace with 2 screws. Repeat the process with the other leg. Fully tighten all the stand’s screws. At this point two spare screws should remain. FR Fixez la barre transversale en bas des pieds à l’aide de 4 vis (2 de chaque côté). Placez le support en position verticale. Fixez la partie externe du montant à la traverse à l’aide de 2 vis.
PAGE 6
15 14 EN FR DE IT ES PT EN To finish the stand assembly check that the 4 wheels are locked.
PAGE 7
18 17 19 20 EN Remove the small flaps from each of the foam end pieces. Do not remove the foam end pieces. Remove the tape from the transparent covering that protects the product. Open the transparent covering and remove the desiccant bag from the top of the product. There is a round yellow button protruding from the top of one stand leg, and a square green button protruding from the top of the other leg. Each button fits into a hole in the product.
PAGE 8
21 22 23 24 EN Place the stand on the product slowly and carefully, so that the colored buttons on the legs fit into the corresponding holes in the product. IMPORTANT: Make sure there is nothing on top of the printer body before continuing. Locate the 4 black screws. Fix the printer to the stand from underneath with the 4 black screws. Check that the wheels on the stand are locked.
PAGE 9
26 25 27 28 EN Make sure there is nothing on the printer. Rotate the product 90°. IMPORTANT: While you rotate, keep the roll feeds face downwards. You may need a third person. Hold the product by the foam end pieces and rotate it until it stands on its feet, with all four wheels in contact with the floor. The T1700 weighs 88.9 kg (196 lb) and T1700d 89.4 kg (197.1 lb). Remove the foam end pieces. Remove the transparent covering from the product.
PAGE 10
29 EN 31 30 32 Install the pocket at the back of the printer. Remove the tape from the stand, and unfold the fabric. Pass the fabric through to the front of the printer and then insert the frame. Check the picture for correct installation. Clip the basket frame to the feet. Press firmly until it clicks into place. The basket is now complete. FR Installez le bac à l’arrière de l’imprimante. Retirez les bandes adhésives et dépliez le tissu.
PAGE 11
33 EN FR DE IT ES PT NL 34 35 3 Set up the printer Configuration de l’imprimante Einrichten des Druckers Installazione della stampante Configuración de la impresora Instalar a impressora De printer opstellen ‫إعداد الطابعة‬ AR 15’ EN Remove the orange tape pieces from the product, except for the ones coming from inside the product. Open the Window. You will see a cardboard support attached to the product with tape. Remove the tape.
PAGE 12
37 36 39 38 90º EN Turn the cardboard support 90° to the right. CAUTION: Avoid hitting the belts. Carefully lift the cardboard support up and out of the product. It will not be needed again; you can discard it. Inside the right-hand side of the product, you will see a piece of cardboard. Remove the cardboard carefully. It will not be needed again so it can be disposed off. FR Faites pivoter le support en carton à 90° sur la droite. ATTENTION : Évitez de percuter les courroies.
PAGE 13
40 41 42 43 7-15’ EN Remove the orange tapes and unlock the wheels. Move the printer to its final destination. Connect the network cable. If you find a USB flash drive in a plastic bag inside the box, it contains the latest Firmware. Please follow the instructions in the bag. Otherwise, please ignore this step. * The USB drive is only needed in some units. Connect the power cable to the printer, and the outlet. FR Retirez les rubans orange et déverrouillez les roues.
PAGE 14
44 45 46 EN FR DE IT ES PT 4 Printhead and cartridge setup Installation des têtes d’impression et des cartouches Einrichten von Druckköpfen und Patronen Installazione delle cartucce e delle testine di stampa Instalación del cabezal de impresión y el cartucho Configuração de cartucho de tinta e cabeçotes de impressão Installatie van printkop en cartridge ‫ تعيين إعدادات الخرطوشة ورأس‬AR ‫الطباعة‬ EN Remove the plastic film covering the window and the plastic film covering the front panel (LCD displa
PAGE 15
47 48 49 50 10’ EN Insert the ink cartridges one-by-one (x6). Each cartridge is marked with its own color, and should be inserted only into the slot of the same color. Avoid touching pins, leads or circuits. The cartridges must be inserted the right way around: the ink outlet in the catridge should meet the ink inlet in the slot. Push the cartridge into the slot until it clicks into place. Close the ink cartridge cover. The printer now prepares the ink system for use.
PAGE 16
52 51 53 54 EN Open the window and pull the blue printhead cover handle up and towards you to release the latch. Push the handle back to raise the lid to access the setup printheads. Look at each setup printhead to verify that it has ink inside. The setup printheads only purpose is to prevent ink loss during ink cartridge installation. Remove and discard all the setup printheads. You may need to use force to extract each printhead. The setup printheads contain ink, which could leak out.
PAGE 17
55 56 57 58 EN When all of the setup printheads have been removed, press “Next”on the front panel. The front panel prompts you to install the new printheads. Unwrap each printhead and remove all orange parts. The printhead is designed to be inserted into any available slot. Once the printhead is inserted into a slot it sets up to work only with that combination of colors, so it is important to mark the printhead with the specific color combination to be used. Insert the printheads one by one.
PAGE 18
60 59 61 62 10’ EN Pull the handle down to close the cover. Ensure that the end of the blue handle catches the wire loop on the near side of the carriage. Lower the handle to rest on the carriage cover. Close the top cover. The product checks and prepares the new printheads. Once the printhead check has finished the product will be ready to load paper for the printhead alignment. FR Tirez sur la poignée vers le bas pour fermer le couvercle du chariot.
PAGE 19
63 65 64 66 EN When the front panel prompts you to load paper for printhead alignment: Take the spindle and use it to load the paper the first time. Note: Calibration requires paper at least 15in (381mm) wide. If the blue removable stop is on the spindle, remove it. Load the roll onto the spindle as indicated in the image. Add the removable stop to the spindle to keep the roll in place. Push the removable stop towards the roll as far as it will go. No gap should be left between stop and paper.
PAGE 20
67 68 69 70 2x EN Feed the leading edge of the paper into the product until the product takes hold of it. Do not insert the roll paper into the cutsheet slot. Note: do not close the roll cover until the front panel notifies you. The product will proceed to align the printheads. This process involves printing, and therefore needs to use paper with a straight leading edge. Note: printhead alignment requires paper at least 15in (381mm) wide. Roll paper is recommended.
PAGE 21
72 71 73 74 EN Open the roll cover. Remove the spindle. Load the roll onto the spindle. Follow the steps 64 and 65. From the back of the product, place the spindle into the product. Feed the leading edge of the paper into the product until the product takes hold of it. Then move to the front of the product. Note: do not close the roll cover until the front panel notifies you. If the paper types of the two rolls differ, go to step 80 and calibrate the paper. FR Ouvrez le capot du rouleau.
PAGE 22
5 EN Connectivity and Mobile Printing ES FR Connectivité et impression mobile 1 - Vérifiez que l’imprimante est correctement connectée à Internet. 2 - Activez les services Web lors de la configuration initiale de l’imprimante, ou ultérieurement, en suivant les instructions qui s’affichent sur le panneau avant. Si le micrologiciel est mis à jour, le redémarrage de l’imprimante peut être nécessaire.
PAGE 23
75 76 77 hp.com/go/DesignJetclick EN The connectivity wizard will now start and take you step by step through connecting your printer to the internet. Follow the instructions. Take note of the printer’s email address for email printing. Install the product software on your computer. Download it from: www.hp.com/go/T1700/drivers Be sure to follow the software installation instructions.
PAGE 24
78 EN Print from your smartphone or tablet - AirPrint must be enabled on the printer. - iOS printing is enabled through Airprint, no installation is required. - For Android printing, install the HP Print Service Plugin from Google Play. - You can also download the HP Smart App (iOS/Android) to enhance your printing capabilities from a smartphone or tablet. For more information visit: http://www.hp.
PAGE 25
79 80 EN Optional: Managing printer security in HP Connected. When you enable web services the printer is in unlock mode meaning everyone who knows the printer’s email address can print. If you are the printer administrator you can change the status to lock mode, customize your printer’s email address, or manage the printer security (you will need the printer code and an account at HP Connected. Check your region’s availability).
PAGE 26
PAGE 27
PAGE 28
EN © Copyright 2017 HP Development Company, L.P. ES The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. FR DE © Copyright 2017 HP Development Company, L.P.