HP DesignJet T1700 Printer Series-Assembly Manual

ManualsBrandsHP ManualsDesktopsHP DesignJet T1700 44-in Printer

Large Format Division

Camí de Can Graells 1-21 · 08174

Sant Cugat del Vallès

Barcelona · Spain

ZHCN

ZHTW

HP DesignJet T1700

Printer Series

Assembly instructions

組み立てマニュアル

组装说明

組裝說明

조립 지침

Petunjuk Perakitan

*W6B56-90006*

W6B56-90006

Hardware Setup:

1- Assemble the stand

2- Attach the printer body to the stand assembly

3- Set up the printer

4- Printhead and cartridge setup

5- Connectivity & Mobile Printing

Software setup:

Now, it’s easy to print large-format documents from virtually anywhere, using your

laptop, printer touchscreen, iPhone®, or iPad®.

Install the product software from www.hp.com/go/T1700/drivers

ハードウェアのセットアップ:

1-スタンドの組み立て

2- プリンタの本体を組み立てたス

タンドに取り付ける

3- プリンタをセットアップする

4-プリントヘッドおよびカートリッジをセットア

ップする

5- 接続およびモバイル印刷

ソフトウェアのセットアップ:

ラップトップコンピュータ、プリンタのタッチス

クリーン、

iPhone®、iPad®を使い、大判ドキュメントをどこか

らでも簡単に印刷できるようになりました。

製品ソフトウェアは、

www.hp.com/go/T1700/drivers

からインストールしてください。

硬件设置:

1-组装支架

2- 将打印机机身安装到支架组件上

3- 设置打印机

4- 打印头和墨盒设置

5- 连接和移动打印

软件设置：

现在，使用便携式电脑、打印机触摸屏、iPhone® 或 iPad®，

即可随时随地轻松打印大幅面文档。

从以下位置中安装产品软件：

www.hp.com/go/T1700/drivers

硬體設定：

1- 組裝機架

2- 將印表機本體組裝到機架組件

3- 設定印表機

4- 印字頭和墨水匣設定

5- 連線與行動列印

軟體設定：

現在，您幾乎可從任何位置，輕鬆列印

大型格式文件，只要使用您的筆記型電腦、印表機

觸控式螢幕、iPhone® 或 iPad® 就可以辦到。

從下列網站安裝產品軟體：www.hp.com/go/T1700/drivers

하드웨어 설치:

1- 스탠드 조립

2- 프린터 본체를 스탠드 조립에 붙

이기

3- 프린터 설치

4- 프린트 헤드 및 카트리지 설치

5- 연결 및 모바일 인쇄

소프트웨어 설치:

이제 노트북, 프린터 터치 스크린, iPhone® 또는

iPad®를 사용하여 어디에서나 대형 파일을 쉽게

인쇄할 수 있습니다.

www.hp.com/go/T1700/drivers

에서 제공하는제품 소프트웨어를 설치하십시오.

Kongurasi Perangkat Keras:

1- Memasang dudukan

2-Memasang badan printer ke

rakitan dudukan

3-Membuat pengaturan awal

printer

4- Kongurasi printhead dan kartrid

5- Konektivitas dan Pencetakan Melalui Perangkat Bergerak

Kongurasi Perangkat Lunak:

Kini Anda dapat dengan mudah mencetak dokumen berformat besar secara virtual di

manapun, menggunakan laptop, layar sentuh printer, iPhone®, atau iPad®.

Instal perangkat lunak produk dari: www.hp.com/go/T1700/drivers

Summary of content (26 pages)

PAGE 1
HP DesignJet T1700 Printer Series EN Assembly instructions JA 組み立てマニュアル ZHCN 组装说明 ZHTW 組裝說明 KO 조립 지침 ID Petunjuk Perakitan EN Hardware Setup: 1- Assemble the stand 2- Attach the printer body to the stand assembly 3- Set up the printer 4- Printhead and cartridge setup 5- Connectivity & Mobile Printing ZHTW 軟體設定：現在，您幾乎可從任何位置，輕鬆列印大型格式文件，只要使用您的筆記型電腦、印表機觸控式螢幕、iPhone® 或 iPad® 就可以辦到。 Software setup: Now, it’s easy to print large-format documents from virtually anywhere, using your laptop, print
PAGE 2
1 EN Please read these instructions carefully. These assembly instructions explain how to assemble the printer. • Because the product is heavy, you may need three people to unpack it. When more than one person is needed, this symbol is displayed *. • You need a roll of 15in (381mm) minimum paper to align the printheads. • You need a LAN connection to connect the printer to the internet. Note: Roll and LAN cables are not included. • To download the printer drivers go to www.hp.com/go/T1700/drivers.
PAGE 3
EN JA ZHCN ZHTW KO ID 4 5 1 Assemble the stand スタンドの組み立て组装支架組裝機架 스탠드 조립 Memasang dudukan X8 40’ EN Locate the stand pieces and remove the following: 1. Right leg / 2. Basket frame / 3. Right foot / 4. Screwdriver and screws / 5. Cross brace / 6. Left foot / 7. Left leg / 8.Cross bar. Fix one foot to a leg with 8 screws. Repeat the process for the other foot and leg. Place the cross brace on the floor with the letters L and R face up. JA スタンド部品を見つけ、トレイから次のものを取り除きます 1. 右脚部 /2. バスケットフレーム/ 3.
PAGE 4
6 7 8 9 EN Slot a leg onto the cross brace to install the leg with the long side of the foot as shown in the image. Important: Note that there are stickers on the legs, make sure the letters match the ones on the cross brace (R with R, L with L). Fix the leg to the cross brace with 3 screws at the inner face of the leg. Important: Do not fully tighten them. Slot the other leg onto the cross brace making sure that the basket supports located on the feet (1 on each foot) are on the same side.
PAGE 5
10 11 12 13 X2+2 EN Fix the cross bar to the bottom of the legs with 4 screws (2 each side) . Turn the stand upright. Attach the outside of the leg to the cross brace with 2 screws. Repeat the process with the other leg. Fully tighten all the stand’s screws. At this point two spare screws should remain.
PAGE 6
15 14 EN JA ZHCN ZHTW KO ID EN To finish the stand assembly check that the 4 wheels are locked. 16 2 Attach the printer body to the stand assembly プリンタの本体を組み立てたスタンドに取り付ける将打印机机身安装到支架组件上將印表機本體組裝到機架組件 프린터 본체를 스탠드 조립에 붙 이 기 Memasang badan printer kerakitan dudukan Remove the tapes from the film, then remove the tray and box. IMPORTANT: Make sure there is nothing on top of the printer body before continuing.
PAGE 7
17 18 19 20 EN Remove the small flaps from each of the foam end pieces. Do not remove the foam end pieces. Remove the tape from the transparent covering that protects the product. Open the transparent covering and remove the desiccant bag from the top of the product. There is a round yellow button protruding from the top of one stand leg, and a square green button protruding from the top of the other leg. Each button fits into a hole in the product.
PAGE 8
21 22 23 24 EN Place the stand on the product slowly and carefully, so that the colored buttons on the legs fit into the corresponding holes in the product. IMPORTANT: Make sure there is nothing on top of the printer body before continuing. Locate the 4 black screws. Fix the printer to the stand from underneath with the 4 black screws. Check that the wheels on the stand are locked.
PAGE 9
25 26 27 28 EN Make sure there is nothing on the printer. Rotate the product 90°. IMPORTANT: While you rotate, keep the roll feeds face downwards. You may need a third person. Hold the product by the foam end pieces and rotate it until it stands on its feet, with all four wheels in contact with the floor. The T1700 weighs 88.9 kg (196 lb) and T1700dr 89.4 kg (197.1 lb). Remove the foam end pieces. Remove the transparent covering from the product.
PAGE 10
29 30 31 32 EN Install the pocket at the back of the printer. Remove the tape from the stand, and unfold the fabric. Pass the fabric through to the front of the printer and then insert the frame. Check the picture for correct installation. Clip the basket frame to the feet. Press firmly until it clicks into place. The basket is now complete.
PAGE 11
33 EN JA ZHCN ZHTW KO ID 34 35 3 Set up the printer プリンタをセットアップする设置打印机設定印表機 프린터 설치 Membuat pengaturan awal printer 15’ EN Remove the orange tape pieces from the product, except for the ones coming from inside the product. Open the Window. You will see a cardboard support attached to the product with tape. Remove the tape.
PAGE 12
37 36 38 39 90º EN Turn the cardboard support 90° to the right. CAUTION: Avoid hitting the belts. Carefully lift the cardboard support up and out of the product. It will not be needed again; you can discard it. Inside the right-hand side of the product, you will see a piece of cardboard. Remove the cardboard carefully. It will not be needed again so it can be disposed off.
PAGE 13
40 41 42 43 7-15’ EN Remove the orange tapes and unlock the wheels. Move the printer to its final destination. Connect the network cable. If you find a USB flash drive in a plastic bag inside the box, it contains the latest Firmware. Please follow the instructions in the bag. Otherwise, please ignore this step. * The USB drive is only needed in some units. Connect the power cable to the printer, and the outlet. JA オレンジ色のテープを取り外し、キャスターのロックを解除します。プリンタを最終的に設置する場所に移動します。ネットワークケーブルを接続し.
PAGE 14
44 45 46 EN JA ZHCN ZHTW KO ID 4 Printhead and cartridge setup プリントヘッドおよびカートリッジをセットアップする打印头和墨盒设置印字頭和墨水匣設定 프린트 헤드 및 카트리지 설치 Konfigurasi printhead dan kartrid 40’ EN Remove the plastic film covering the window and the plastic film covering the front panel (LCD display). When all cables are connected, switch the printer on. On the front panel, the HP logo appears. Please wait a while. You will then be prompted to select the language of the product.
PAGE 15
47 48 49 50 10’ EN Insert the ink cartridges one-by-one (x6). Each cartridge is marked with its own color, and should be inserted only into the slot of the same color. Avoid touching pins, leads or circuits. The cartridges must be inserted the right way around: the ink outlet in the catridge should meet the ink inlet in the slot. Push the cartridge into the slot until it clicks into place. Close the ink cartridge cover. The printer now prepares the ink system for use.
PAGE 16
51 52 53 54 EN Open the window and pull the blue printhead cover handle up and towards you to release the latch. Push the handle back to raise the lid to access the setup printheads. Look at each setup printhead to verify that it has ink inside. The setup printheads only purpose is to prevent ink loss during ink cartridge installation. Remove and discard all the setup printheads. You may need to use force to extract each printhead. The setup printheads contain ink, which could leak out.
PAGE 17
55 56 57 58 EN When all of the setup printheads have been removed, press “Next”on the front panel. The front panel prompts you to install the new printheads. Unwrap each printhead and remove all orange parts. The printhead is designed to be inserted into any available slot. Once the printhead is inserted into a slot it sets up to work only with that combination of colors, so it is important to mark the printhead with the specific color combination to be used. Insert the printheads one by one.
PAGE 18
59 60 61 62 10’ EN Pull the handle down to close the cover. Ensure that the end of the blue handle catches the wire loop on the near side of the carriage. Lower the handle to rest on the carriage cover. Close the top cover. The product checks and prepares the new printheads. Once the printhead check has finished the product will be ready to load paper for the printhead alignment.
PAGE 19
63 65 64 66 EN When the front panel prompts you to load paper for printhead alignment: Take the spindle and use it to load the paper the first time. Note: Calibration requires paper at least 15in (381mm) wide. If the blue removable stop is on the spindle, remove it. Load the roll onto the spindle as indicated in the image. Add the removable stop to the spindle to keep the roll in place. Push the removable stop towards the roll as far as it will go. No gap should be left between stop and paper.
PAGE 20
67 68 69 70 2x EN Feed the leading edge of the paper into the product until the product takes hold of it. Do not insert the roll paper into the cutsheet slot. Note: do not close the roll cover until the front panel notifies you. The product will proceed to align the printheads. This process involves printing, and therefore needs to use paper with a straight leading edge. Note: printhead alignment requires paper at least 15in (381mm) wide. Roll paper is recommended.
PAGE 21
71 72 73 74 EN Open the roll cover. Remove the spindle. Load the paper onto the spindle as indicated in steps 64 and 65. From the back of the product, place the spindle into the product. Feed the leading edge of the paper into the product until the product takes hold of it. Then move to the front of the product. Note: do not close the roll cover until the front panel notifies you. If the paper types of the two rolls differ, go to step 80 and calibrate the paper.
PAGE 22
EN 5 Connectivity and Mobile Printing KO 1 - Make sure that your printer is correctly connected to the Internet. 2 - Enable the services during initial setup of the printer, or later following the instructions in the front panel. The printer may need to restart if the firmware has updated.
PAGE 23
75 76 77 hp.com/go/DesignJetclick EN The connectivity wizard will now start and take you step by step through connecting your printer to the internet. Follow the instructions. Take note of the printer’s email address for email printing. Install the product software on your computer. Download it from: www.hp.com/go/T1700/drivers Be sure to follow the software installation instructions.
PAGE 24
78 從智慧型手機或平板電腦列印︰ - 印表機必須啟用 AirPrint。 - iOS 列印是透過 Airprint 啟用，不需要任何安裝作業。 - 如需 Android 列印，請從 Google Play 安裝 HP 列印服務外掛程式。 - 您也可以下載 HP Smart App (iOS/Android) 應用程式，以強化從智慧型手機或平板電腦進行列印的功能。詳情請上網查詢： http://www.hp.com/go/designjetmobility EN Print from your smartphone or tablet - AirPrint must be enabled on the printer. - iOS printing is enabled through Airprint, no installation is required. - For Android printing, install the HP Print Service Plugin from Google Play.
PAGE 25
79 80 EN Optional: Managing printer security in HP Connected. When you enable web services the printer is in unlock mode meaning everyone who knows the printer’s email address can print. If you are the printer administrator you can change the status to lock mode, customize your printer’s email address, or manage the printer security (you will need the printer code and an account at HP Connected. Check your region’s availability).
PAGE 26
EN © Copyright 2017 HP Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. JA © Copyright 2017 HP Development Company, L.P.