HP Mini 2102, HP Mini 210, and Compaq Mini 210 Maintenance and Service Guide
© Copyright 2009, 2010 Hewlett-Packard Development Company, L.P. Intel is a trademark of Intel Corporation in the U.S. and other countries. Microsoft, Windows, and Windows Vista are U.S. registered trademarks of Microsoft Corporation. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation.
iv Safety warning notice
Table of contents 1 Product description ........................................................................................................... 1 2 External component identification ..................................................................................... 5 Identifying the hardware ........................................................................................................... 5 Top components .......................................................................................
Workstation guidelines .............................................................. 35 Equipment guidelines ................................................................. 36 Component replacement procedures ........................................................................................ 37 Computer feet ......................................................................................................... 37 Battery .............................................................................
Using the Instant Restore utility when the operating system is functioning ......... 78 Using the Instant Restore utility when the operating system is not functioning .... 78 Using Windows Backup and Restore ......................................................................... 78 Using system restore points ....................................................................................... 79 When to create restore points ....................................................................
viii
1 Product description Category Description HP Mini 2102 and HP Mini 210 Product Name HP Mini 2102 √ HP Mini 210 √ Compaq Mini 210 Processor Compaq Mini 210 √ Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB) √ √ Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB), 6.
Category Description HP Mini 2102 and HP Mini 210 Compaq Mini 210 Supports the following configurations: √ √ √ √ ● 1-GB total system memory NOTE: Supported on computers with all operating systems ● 2-GB total system memory NOTE: Supported only on computers with Windows 7 Premium, Windows 7 Professional, and Windows 7 Starter with Certificate of Authenticity (COA) Emerging Markets and FreeDOS, and in China, Windows XP only. Hard drives Supports the following 9.5-mm (0.37-in) × 6.35-cm (2.
Category Description HP Mini 2102 and HP Mini 210 Compaq Mini 210 Wireless Integrated WLAN by way of: √ √ 2 WLAN antennas built into display assembly √ √ Integrated WWAN by way of HP un2400 Mobile Broadband Module (optional) √ √ Digital Media Slot (consumer models) or Media Card Reader (commercial models) with push-push technology supporting: √ √ √ √ Audio-in/out combo, supporting jack detection √ √ RJ-45 (Ethernet, includes link and activity lights) √ √ USB (2–3) √ √ VGA, suppor
Category Description HP Mini 2102 and HP Mini 210 Compaq Mini 210 HP Clikpad TouchPad with multi-touch/gesture support √ √ 40-W UMA AC adapter (non-Smart) with localized cable plug support and stepped plug √ √ AC adapter connector on cable √ √ 1.0-m (3.28-ft) power cord √ √ 3-cell Lithium-ion (Li-ion) battery (3s1P, 2.55-Ah, 28-Wh) √ √ 6-cell battery (3s2P, 2.55-Ah, 55-Wh) √ √ 6-cell high capacity battery (3s2P, 3.0-Ah, 66.
2 External component identification Identifying the hardware Components included with the computer may vary by region and model. The illustrations in this chapter identify the standard features on most computer models. To see a list of hardware installed in the computer, follow these steps: 1. Select Start > My Computer. 2. In the left pane of the System Tasks window, select View system information. 3. Select Hardware tab > Device Manager.
Top components TouchPad Item Component Description (1) TouchPad on/off button Turns the TouchPad on and off. Quickly double-tap the button to turn the TouchPad on and off. (2) TouchPad Moves the pointer and selects or activates items on the screen. (3) Left TouchPad button* Functions like the left button on an external mouse. (4) Right TouchPad button* Functions like the right button on an external mouse. *This table describes factory settings.
Lights Item Component Description (1) TouchPad light ● On: The TouchPad is disabled. ● Off: The TouchPad is enabled. (2) Caps lock light On: Caps lock is on. (3) Mute light On: Speaker sound is off. (4) Wireless light ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/ or a Bluetooth device, is on. NOTE: Wireless devices are enabled at the factory. ● Off: All wireless devices are off.
Keys Item Component Description (1) Action keys Execute frequently used system functions. (2) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (3) Windows logo key Displays the Windows Start menu. (4) Windows applications key Displays a shortcut menu for items beneath the pointer. Front components 8 Component Description Speakers (2) Produce sound.
Right-side components item Component Description (1) Digital Media Slot Supports the following optional digital card formats: (2) (3) Power light Power switch ● Memory Stick (MS) ● MS/Pro ● MultiMediaCard (MMC) ● Secure Digital High Capacity (SDHC) Memory Card (standard and large size) ● xD-Picture ● White: The computer is on. ● Blinking white: The computer is in the Standby state. ● Off: The computer is off or in Hibernation.
item Component Description (6) RJ-45 (network) jack and cover Connects a network cable. (7) Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. Left-side components 10 item Component Description (1) Power connector Connects an AC adapter. (2) Battery light ● Off: The computer is running on battery power.
item Component Description (6) USB port Connects an optional USB device. (7) Audio-out (headphone) jack/Audio-in (microphone) jack Produces sound when connected to optional powered stereo speakers, headphones, earbuds, a headset, or television audio. Also connects an optional headset microphone. NOTE: When an audio component is connected to the jack, the computer speakers are disabled. The audio component cable must have a 4-conductor connector.
Bottom components 12 item Component Description (1) Battery release latches (2) Release the battery from the battery bay. (2) Battery bay Holds the battery.
Wireless antennas item Component Description (1) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide-area networks (WWANs), (2) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local-area networks (WLANs). *The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions.
3 Illustrated parts catalog Serial number label location When ordering parts or requesting information, the serial number label, located inside the battery bay area of the computer, provides important information that you may need when contacting technical support. NOTE: Serial number label location, format, and color vary on select models.
Computer major components Item Description Spare part number (1) Display assembly, 25.7 cm (10.
Item Description Spare part number ● WSVGA, flush glass display assembly in red 612202-001 ● WSVGA, flush glass display assembly in silver 612196-001 ● HD, flush glass display assembly in black 612201-001 ● HD, flush glass display assembly in blue 612199-001 ● HD, flush glass display assembly in red 612203-001 ● HD, flush glass display assembly in silver 612197-001 ● WSVGA, AntiGlare, flush glass display assembly in pink 605040-001 ● HD, AntiGlare, flush glass display assembly in pi
Item Description Spare part number ● For use in Spain 590527-071 ● For use in Switzerland 590527-BG1 ● For use in Taiwan 590527-AB1 ● For use in Thailand 590527-281 ● For use in Turkey 590527-141 ● For use in the United Kingdom 590527-031 ● For use in the United States 590527-001 White (for full-feature models only): ● For use in Belgium 607977-A41 ● For use in Brazil 607977-201 ● For use in the Czech Republic 607977-221 ● For use in Denmark, Finland, and Norway 607977-DH1
Item Description Spare part number ● For use in the United Kingdom 607977-031 ● For use in the United States 607977-001 Pink (for full-feature models only): (3) ● For use in Belgium 607978-A41 ● For use in Brazil 607978-201 ● For use in the Czech Republic 607978-221 ● For use in Denmark, Finland, and Norway 607978-DH1 ● For use in France 607978-051 ● For use in French Canada 607978-121 ● For use in Germany 607978-041 ● For use in Greece 607978-DJ1 ● For use in Hungary 60
Item Description Spare part number In pink 608304-001 In white 608305-001 For de-feature (DF) models only: In black 596144-001 (4) Speakers (includes cable) 596153-001 (5) System board (includes replacement thermal material): Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB) 608951-001 Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB), decoder ring, WWAN 608952-001 Intel® Atom™ N455 1.
Item Description Spare part number Atheros 9285G 802.11b/g/n Half MiniCard 605560-001 Broadcom 4313/2070 802.11b/g/n (1x1) and BT Half MiniCard 600370-001 Broadcom BCM94313HMG2L 802.11b/g/n (1x1) Half MiniCard 593836-001 Ralink RT3090 802.
Display assembly components NOTE: Display assembly subcomponents are available only for standard display assemblies. Flush glass display assemblies are available only as hinge-up assemblies. Item Description (1) Display bezel (includes WLAN antenna transceivers and cables and WWAN antenna transceivers and cables): (2) (3) Spare part number For use only with HP Mini 2102 and 210 computer models 589656-001 For use only with Compaq Mini 210 computer models 589655-001 Display panel: 25.7-cm (10.
Item Description Spare part number Display hinge caps (not illustrated) 598850-001 (4) Webcam/microphone module 589654-001 (5) ● Display panel cable, WSVGA (includes webcam/microphone module cable) 589664-001 ● Display panel cable, HD (includes webcam/microphone module cable) 599473-001 (6) 22 Display enclosure (includes WLAN antenna transceivers and cables and WWAN antenna transceivers and cables): For use only with HP computer models in black 589661-001 For use only with HP computer mod
Mass storage devices NOTE: Each hard drive spare part kit includes a cable adapter, bracket, and 4 isolators.
Miscellaneous parts Description Spare part number 40-W UMA AC adapter, non-smart RC/V 584540-001 40-W UMA AC adapter, non-smart RC/V 2W 613162-001 Power cord: 24 For use in Argentina 490371-D01 For use in Austalia 490371-011 For use in Brazil 490371-201 For use in Denmark 490371-081 For use in Europe 490371-021 For use in Israel 490371-BB1 For use in Italy 490371-061 For use in Japan 490371-291 For use in the People's Republic of China 490371-AA1 For use in Singapore and the United
Sequential part number listing Spare part number Description 490371-001 Power cord for use in North America 490371-011 Power cord for use in Australia 490371-021 Power cord for use in Europe, the Middle East, and Africa 490371-031 Power cord for use in Singapore and the United Kingdom 490371-061 Power cord for use in Italy 490371-081 Power cord for use in Denmark 490371-111 Power cord for use in Switzerland 490371-201 Power cord for use in Brazil 490371-291 Power cord for use in Japan 49
26 Spare part number Description 589659-001 Display enclosure for use only with HP Mini 2102 and 210 computer models in red (includes WLAN antenna transceivers and cables and WWAN antenna transceivers and cables) 589660-001 Display enclosure for use only with HP Mini 2102 and 210 computer models in blue (includes WLAN antenna transceivers and cables and WWAN antenna transceivers and cables) 589661-001 Display enclosure for use only with HP Mini 2102 and 210 computer models in black (includes WLAN an
Spare part number Description 590527-291 Keyboard, black, for use only in Japan (includes cable) 590527-A41 Keyboard, black, for use only in Belgium (includes cable) 590527-AB1 Keyboard, black, for use only in Taiwan (includes cable) 590527-AD1 Keyboard, black, for use only in South Korea (includes cable) 590527-B31 Keyboard, black, for use only in the Netherlands (includes cable) 590527-BA1 Keyboard, black, for use only in Slovenia (includes cable) 590527-BB1 Keyboard, black, for use only in
28 Spare part number Description 605040-001 25.7-cm (10.1-in) WSVGA, AntiGlare, flush glass display assembly in pink (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN transceivers and cables, and webcam/ microphone module and cable) 605041-001 25.7-cm (10.1-in) HD, AntiGlare, flush glass display assembly in pink (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN transceivers and cables, and webcam/ microphone module and cable) 605560-001 Atheros 9285G 802.
Spare part number Description 607977-001 Keyboard, white, for use only in the United States (includes cable) 607977-031 Keyboard, white, for use only in the United Kingdom (includes cable) 607977-041 Keyboard, white, for use only in Germany (includes cable) 607977-051 Keyboard, white, for use only in France (includes cable) 607977-061 Keyboard, white, for use only in Italy (includes cable) 607977-071 Keyboard, white, for use only in Spain (includes cable) 607977-121 Keyboard, white, for use o
30 Spare part number Description 608307-001 Service cover, pink 608308-001 Service cover, white 608951-001 Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB) 608952-001 Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB), decoder ring, WWAN 608953-001 Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB), Broadcom FLEA 608954-001 Intel® Atom™ N455 1.
Spare part number Description 614994-001 Service cover, silver (Brazil only) 615862-001 1-GB memory module (667-MHz, DDR3): 615863-001 2-GB memory module (667-MHz, DDR3): 615864-001 1-GB memory module (667-MHz, DDR3), WWAN 615865-001 2-GB memory module (667-MHz, DDR3), WWAN Sequential part number listing 31
4 Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.
Cables and connectors CAUTION: When servicing the device, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the device. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables.
Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.
Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations. ● Place items on a grounded surface before removing items from their containers.
Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
Component replacement procedures This chapter provides removal and replacement procedures. There are as many as 33 screws, in 5 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement. Computer feet The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Feet Kit, spare part number 589680-001.
Battery Description Spare part number 6-cell high-capacity, 66.6-WHr (includes 2 release latches and 2 rubber feet) 596240-001 6-cell, 55-WHr (includes 2 release latches and 2 rubber feet) 596239-001 3-cell, 28-WHr (includes 2 release latches) 590543-001 Before disassembling the computer, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
SIM Before removing the SIM, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38). Remove the SIM: 1.
Service cover Description Spare part number Service cover 589679-001 Service cover, blue 596146-001 Service cover, red 596147-001 Service cover, silver 596148-001 Service cover 589679-001 Service cover, for use only with DF computer models 600707-001 Service cover, pink 608307-001 Service cover, white 608308-001 Service cover, for use only with DF computer models (Brazil only) 614991-001 Before removing the service cover, follow these steps: 1. Shut down the computer.
2. Release the right side of the service cover (2) by lifting it slightly away from the base enclosure. NOTE: It is normal for the service cover to flex slightly when it is released. You may also hear some popping noises as the service cover tabs disengage from the base enclosure slots. 3. Press the left release button (1). 4. Release the left side of the service cover (2) by lifting it slightly from away from the base enclosure.
5. Continue lifting the rear edge of the service cover (1) up and forward until it rests at an angle, and then remove the service cover (2). Install the service cover: 42 1. Place the service cover above the computer at an angle, with the front edge toward the front of the computer. 2. Insert the front edge of the service cover (1) into the front edge of the base enclosure, making sure the tabs on the cover insert into the slots on the base enclosure (2).
3. Swing the rear edge of the service cover (1) back and down, and then firmly press down on the cover (2) so the clips on the cover access the slots on the base enclosure. Hard drive NOTE: Each hard drive spare part kit includes a cable adapter, bracket, and four rubber isolators.
3. Remove the hard drive (4) by sliding it up and to the right at an angle. 4. If it is necessary to replace the hard drive bracket, follow these steps: a. Disconnect the cable adapter (1) from the hard drive. b. Remove the four Phillips PM3.0×3.0 screws (2) that secure the hard drive bracket to the drive. c. Remove the hard drive bracket (3). d. Remove the four rubber isolators (4) from the bracket. Reverse this procedure to reassemble and install the hard drive.
WWAN module Description Spare part number HP un2400 Mobile Broadband WWAN module 531993-001 CAUTION: The WWAN module and the WLAN module are not interchangeable. To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region.
3. Remove the WWAN module (4) by pulling the module away from the slot at an angle. NOTE: WWAN modules are designed with a notch (5) to prevent incorrect insertion of the WWAN module into the WWAN module slot. Reverse this procedure to install the WWAN module.
WLAN module Description Spare part number Atheros 9285G 802.11b/g/n Half MiniCard 605560-001 Broadcom 4313/2070 802.11b/g/n (1x1) and BT Half MiniCard 600370-001 Broadcom BCM94313HMG2L 802.11b/g/n (1x1) Half MiniCard 593836-001 Ralink RT3090 802.11b/g/n + BC4 Bluetooth PCI-e half MiniCard 602992-001 CAUTION: The WWAN module and the WLAN module are not interchangeable.
3. Remove the WLAN module (3) by pulling the module away from the slot at an angle. NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion of the WLAN module into the WLAN module slot. Reverse this procedure to install the WLAN module.
Memory module Description Spare part number 1-GB memory module (667-MHz, DDR3) 615862-001 2-GB memory module (667-MHz, DDR3) 615863-001 1-GB memory module (667-MHz, DDR3), WWAN 615864-001 2-GB memory module (667-MHz, DDR3), WWAN 615865-001 Before removing the memory module, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
2. Grasp the edge of the memory module (2), and then pull it out of the memory module slot. NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the memory module slot. Reverse this procedure to install the memory module.
RTC battery Description Spare part number RTC battery 599516-001 Before removing the real-time clock (RTC) battery, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Keyboard NOTE: The keyboard spare part kit includes a keyboard cable.
For use in: Spare part number For use in: Spare part number Belgium 590527-A41 The Netherlands 590527-B31 Brazil 590527-201 Portugal 590527-131 The Czech Republic 590527-221 Russia 590527-251 Denmark, Finland, and Norway 590527-DH1 Saudi Arabia 590527-171 France 590527-051 Slovenia 590527-BA1 French Canada 590527-121 South Korea 590527-AD1 Germany 590527-041 Spain 590527-071 Greece 590527-DJ1 Switzerland 590527-BG1 Hungary 590527-211 Taiwan 590527-AB1 Israel 590527-B
Remove the keyboard: 54 1. Remove the three Phillips PM2.0×6.0 screws that secure the keyboard to the computer. 2. Turn the computer right-side up, with the front toward you. 3. Open the computer as far as it will open. 4. Lift the rear edge of the keyboard (1) until it rests at an angle. 5. Slide the keyboard (2) back until the keyboard cable and connector are accessible. 6.
Reverse this procedure to install the keyboard.
Top cover NOTE: The top cover includes the TouchPad board and bracket. Description Spare part number In black, for use only with FF computer models 589676-001 In black, for use only with DF computer models 596144-001 In pink 608304-001 In white 608305-001 Before removing the top cover, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
5. Disconnect the speaker cable (1) from the system board. 6. Release the ZIF connector (2) to which the TouchPad cable is connected, and then disconnect the TouchPad cable (3) from the system board. 7. Remove the five Phillips PM2.0×6.0 screws that secure the top cover to the base enclosure. 8. Release the top cover (1) by lifting the rear edge until it disengages from the base enclosure.
9. Remove the top cover (2) by lifting it straight up. Reverse this procedure to install the top cover.
Speakers Description Spare part number Speakers (include cables) 596153-001 Before removing the speakers, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC Adapter from the computer.
Reverse this procedure to install the speakers.
Display assembly Description Spare part number 25.7-cm (10.
Remove the display assembly: 62 1. Close the computer. 2. Turn the computer upside down, with the front toward you. 3. Release the WLAN antenna cables (1) from the clips built into the base enclosure (2). 4. Turn the computer right-side up, with the front toward you. 5. Open the computer as far as it will open. 6. Disconnect the display panel cable (1) from the system board.
7. Release the wireless antenna cables (2) from the clip built into the base enclosure. CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in damage to the display assembly and other device components. 8. Remove the two Phillips PM2.0×4.0 screws (1) that secure the display assembly to the base enclosure. 9. Remove the display assembly (2). Reverse this procedure to reassemble and install the display assembly.
System board NOTE: The system board spare part kit includes replacement thermal material. Description Spare part number Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB) 608951-001 Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB), decoder ring, WWAN 608952-001 Intel® Atom™ N455 1.66-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB), Broadcom FLEA 608953-001 Intel® Atom™ N455 1.
When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● SIM (see SIM on page 39) ● WWAN module (see WWAN module on page 45) ● WLAN module (see WLAN module on page 47) ● Memory module (see Memory module on page 49) ● RTC battery (see RTC battery on page 51) ● Fan/heat sink assembly (see Fan/heat sink assembly on page 67) Remove the system board: 1.
5. Remove the system board (3) by sliding it up and away from the base enclosure. Reverse the procedure to install the system board.
Fan/heat sink assembly Description Spare part number Fan/heat sink assembly (includes replacement thermal material) 589681-001 NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side of the computer. The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist.
4. Remove the fan/heat sink assembly (3). NOTE: Due to the adhesive quality of the thermal material located between the fan/heat sink assembly and system board components, it may be necessary to move the fan/heat sink assembly from side to side to detach it from the system board.
Power connector cable Description Spare part number Power connector cable 589682-001 Before removing the power connector cable, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
3. Remove the power connector cable (3). Reverse this procedure to install the power connector cable.
5 Setup Utility Starting Setup Utility Setup Utility is a ROM-based information and customization utility that can be used even when your Windows operating system is not working. The utility reports information about the computer and provides settings for startup, security, and other preferences. To start Setup Utility: ▲ Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10 = BIOS Setup Options” message is displayed in the lower-left corner of the screen.
Navigating and selecting in Setup Utility Because Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection are by keystroke. ● To choose a menu or a menu item, use the arrow keys. ● To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the arrow keys or f5 or f6. ● To select an item, press enter. ● To close a text box or return to the menu display, press esc.
Exiting Setup Utility You can exit Setup Utility with or without saving changes. ● To exit Setup Utility and save your changes from the current session: If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Saving Changes, and then press enter. ● To exit Setup Utility without saving your changes from the current session: If the Setup Utility menus are not visible, press esc to return to the menu display.
System Configuration Menu Select To do this Language Support Change the Setup Utility language. Processor C4 State Enable/disable the processor C4 standby state. Boot Options Set the following boot options: ● f10 and f12 Delay (sec.)―Set the delay for the f10 and f12 functions of Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20). ● HP QuickWeb―Enable/disable the QuickWeb Boot menu in Setup Utility. ● Internal Network Adapter boot―Enable/disable boot from Internal Network Adapter.
6 Backup and recovery (Windows only) Windows 7 To protect your information, back up your files and folders. In case of system failure, you can use the backup files to restore your computer. CAUTION: In the event of a hard drive failure, you cannot use your computer to access the Disaster Recovery utility. Therefore, HP recommends that you download the Disaster Recovery utility SoftPaq, and then extract it to a USB flash drive as soon as possible after software setup.
To copy the screen and paste it into a word-processing document, follow these steps: 1. Display the screen. 2. Copy the screen: To copy the active window, press alt+prt sc. To copy the entire screen, press prt sc. 3. Open a word-processing document, click Edit, and then click Paste. 4. Save the document. Creating a copy of the hard drive The back up drive function of BackOnTrack creates a Disaster Recovery Set that is an exact image of your hard drive data.
Using the Disaster Recovery utility NOTE: To perform a recovery with Disaster Recovery, you need a USB flash drive (purchased separately). For optimum performance, the capacity of the drive should be no larger than 2 GB. Disaster Recovery recovers data from a Disaster Recovery Set that you previously created with Roxio BackOnTrack. Disaster Recovery is available from the HP Web site in a compressed file called a SoftPaq. NOTE: Running the SoftPaq makes the USB drive bootable.
Using the Instant Restore utility You can restore your computer from Windows when the operating system is functioning. If the operating system is not functioning, you can also access the utility by restarting your computer. NOTE: For more information about the Instant Restore utility, refer to the BackOnTrack software Help. Using the Instant Restore utility when the operating system is functioning To recover information when the operating system is functioning properly, follow these steps: 1.
Using system restore points When you back up your system, you are creating a system restore point. A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then revert back to that point if you want to reverse subsequent changes made to your system. NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since the last restore point.
Backing up and recovering using HP Recovery Manager If your computer includes HP Recovery Manager, tools provided by the operating system and by HP Recovery Manager software are designed to help you with the following tasks for safeguarding your information and restoring it in case of a system failure: ● Backing up your information ● Creating a set of recovery discs ● Creating system restore points ● Recovering a program or driver ● Performing a full system recovery Backing up your information As
3. Open a word-processing document, click Edit, and then click Paste. 4. Save the document. ● You can back up your information to an optional external hard drive, a network drive, or discs. ● When backing up to discs, use any of the following types of discs (purchased separately): CD-R, CD-RW, DVD+R, DVD-R, or DVD±RW. The discs you use depend on the type of optical drive you are using.
Performing a recovery NOTE: You can recover only files that you have previously backed up. HP recommends that you use Recovery Manager to create a set of recovery discs (entire drive backup) as soon as you set up your computer. Recovery Manager software allows you to repair or restore the system if you experience system failure or instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery partition (select models only) on the hard drive.
– or – a. Turn on or restart the computer. b. Press f11 while the “Press for recovery” message is displayed on the screen. NOTE: It may take several minutes for Recovery Manager to load. 2. In the Recovery Manager window, click System Recovery. 3. Follow the on-screen instructions. Windows XP To protect your information, back up your files and folders. In case of system failure, you can use the backup files to restore your computer.
Creating a copy of the hard drive The back up drive function of BackOnTrack creates a Disaster Recovery Set that is an exact image of your hard drive data. You can back up the image to an external hard drive (purchased separately). To create a Disaster Recovery Set using BackOnTrack, follow these steps: NOTE: Be sure that the computer is connected to AC power before you start the backup process. 1. Click Start, click All Programs, and then click Roxio. 2.
Using the Disaster Recovery Utility NOTE: To perform a recovery with Disaster Recovery, you need a USB flash drive (purchased separately). For optimum performance, the capacity of the drive should be no larger than 2 GB. Disaster Recovery recovers data from a Disaster Recovery Set that you previously created with Roxio BackOnTrack. Disaster Recovery is available from the HP Web site in a compressed file called a SoftPaq. NOTE: Running the SoftPaq makes the USB drive bootable.
Using the Instant Restore utility You can restore your computer from Windows when the operating system is functioning. If the operating system is not functioning, you can also access the utility by restarting your computer. NOTE: For more information about the Instant Restore utility, refer to the BackOnTrack software Help. Using the Instant Restore utility when the operating system is functioning To recover information when the operating system is functioning properly, follow these steps: 1.
7 Connector pin assignments Audio-in (microphone) Pin Signal 1 Audio signal in 2 Audio signal in 3 Ground Audio-out (headphone) Pin Signal 1 Audio out, left channel 2 Audio out, right channel 3 Ground Audio-in (microphone) 87
External monitor 88 Pin Signal 1 Red analog 2 Green analog 3 Blue analog 4 Not connected 5 Ground 6 Ground analog 7 Ground analog 8 Ground analog 9 +5 VDC 10 Ground 11 Monitor detect 12 DDC 2B data 13 Horizontal sync 14 Vertical sync 15 DDC 2B clock Chapter 7 Connector pin assignments
RJ-45 (network) Pin Signal 1 Transmit + 2 Transmit - 3 Receive + 4 Unused 5 Unused 6 Receive - 7 Unused 8 Unused Universal Serial Bus Pin Signal 1 +5 VDC 2 Data 3 Data + 4 Ground RJ-45 (network) 89
8 Power cord set requirements The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used.
Requirements for specific countries and regions Country/region Accredited agency Applicable note number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 The Netherlands KEMA 1 Norway NEMKO 1 The People's Republic of China COC 5 South Korea EK 4 Sweden SEMKO 1 Switzlerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1.
9 Recycling Battery When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal. Display WARNING! The backlight contains mercury. Caution must be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. CAUTION: The procedures in this chapter can result in damage to display components.
Perform the following steps: 1. Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. 2. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel 3.
94 4. Disconnect all display panel cables (1) from the display inverter and remove the inverter 2. 5. Remove all screws (1) that secure the display panel assembly to the display enclosure. 6. Remove the display panel assembly (2) from the display enclosure. 7. Turn the display panel assembly upside down. 8. Remove all screws that secure the display panel frame to the display panel. 9.
10. Remove the display panel frame (2) from the display panel. 11. Remove the screws (1) that secure the backlight cover to the display panel. 12. Lift the top edge of the backlight cover (2) and swing it outward. 13. Remove the backlight cover. 14. Turn the display panel right-side up. 15. Remove the backlight cables (1) from the clip (2) in the display panel. 16. Turn the display panel upside down.
17. Remove the backlight frame from the display panel. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. 18. Remove the backlight from the backlight frame. 19. Disconnect the display cable (1) from the LCD panel. 20. Remove the screws (2) that secure the LCD panel to the display rear panel. 21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel. 23. Remove the LCD panel. 24. Recycle the LCD panel and backlight.
Index A AC adapter spare part numbers 30 AC adapter, spare part numbers 24, 25 action keys 8 antenna locations 13 audio, product description 2 audio-in jack connector pinout 87 location 11 audio-out jack connector pinout 87 location 11 B backup and recovery, Windows 7 backing up information 80 creating hard drive copy 76 creating recovery discs 81 Disaster Recovery utility 77 HP Recovery Manager 80 Instant Restore utility 78 performing a recovery 76, 82 restoring to previous date and time 79 system restore
display hinge caps, spare part numbers 22 Display Hinge Kit, spare part numbers 21, 25 display panel cable, HD spare part numbers 27 display panel cable, spare part numbers 22, 26 display panel, spare part numbers 21 display rubber kit spare part numbers 27 Display Rubber Kit, spare part numbers 22 Display Screw Kit, spare part numbers 22, 26 display switch 11 drive light 10 drives, preventing damage 33 DVD±RW and CD-RW SuperMulti Combo Drive, spare part numbers 23, 25 E electrostatic discharge 34 Ethernet,
plastic parts 32 pointing device components 6 product description 3 ports external monitor 10 monitor 10 product description 3 Universal Serial Bus (USB) 9, 11 power connector 10 power connector cable removal 69 spare part numbers 19, 26, 69 power cord requirements for all countries 90 requirements for specific countries and regions 91 set requirements 90 spare part numbers 24, 25 power light 9 power requirements, product description 4 power switch 9 processor C4 state 74 processor, product description 1 pr
webcam/microphone module, spare part numbers 22, 25 Windows applications key 8 Windows logo key 8 wireless antenna locations 13 wireless light 7 wireless module, product description 3 WLAN module removal 47 spare part numbers 19, 25, 27, 28, 47 workstation guidelines 35 WWAN module removal 45 spare part numbers 20, 25, 45 Index 101
