HP ProBook Notebook PC User Guide
© Copyright 2010 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Features ........................................................................................................................................................... 1 Identifying hardware ............................................................................................................................. 1 Top components .................................................................................................................. 1 TouchPad ...................................
Cleaning the TouchPad and keyboard ............................................................................................... 17 3 Multimedia ..................................................................................................................................................... 19 Multimedia features ............................................................................................................................ 19 Identifying your multimedia components .........................
Using battery power ........................................................................................................................... 33 Inserting or removing the battery ....................................................................................... 34 Charging a battery ............................................................................................................. 35 Maximizing battery discharge time ..........................................................................
7 External media cards .................................................................................................................................... 61 Using Media Card Reader cards ........................................................................................................ 61 Inserting a digital card ........................................................................................................ 61 Removing a digital card ..........................................................
Diagnostics menu .............................................................................................................. 86 System Configuration menu .............................................................................................. 87 Index ...................................................................................................................................................................
x
1 Features Identifying hardware ▲ To see a list of hardware installed in the computer, select Computer > Control Center > YaST > Hardware Information. Top components TouchPad Component Description (1) To turn the TouchPad zone on and off, quickly double-tap the TouchPad off indicator. TouchPad off indicator NOTE: When the TouchPad zone is active, the light is off. (2) TouchPad zone Moves the pointer and selects or activates items on the screen.
Lights NOTE: Refer to the illustration that most closely matches your computer. 2 Component Description (1) ● Amber: The TouchPad is off. ● Off: The TouchPad is on. TouchPad off indicator (2) Caps lock light On: Caps lock is on. (3) E-mail client light Blinking: Launching Evolution e-mail client. (4) Web browser light Blinking: Launching Firefox browser.
Component Description (5) ● On: The computer is on. ● Blinking: The computer is in the Suspend state. ● Off: The computer is off or in Hibernation. ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off.
Component Description (3) ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button to shut down the computer. ● When the computer is in the Suspend state, press the button briefly to exit Suspend. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Keys NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (3) Embedded numeric keypad keys Can be used like the keys on an external numeric keypad when pressed in combination with the fn and num lk keys.
Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (3) Integrated numeric keypad keys Can be used like the keys on an external numeric keypad. (4) Function keys Execute frequently used system functions when pressed in combination with the fn key.
Component Description (1) USB ports (2) Connect optional USB devices. (2) RJ-11 (modem) jack (select models only) Connects a modem cable. (3) Optical drive light (select models only) Blinking: The optical drive is being accessed. (4) Optical drive (select models only) Reads optical discs and, on select models, also writes to optical discs. Component Description (1) USB ports (2) Connect optional USB devices. (2) RJ-11 (modem) jack (select models only) Connects a modem cable.
Component Description (1) Attaches an optional security cable to the computer. Security cable slot NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (2) Power connector Connects an AC adapter. (3) AC adapter light ● On: The computer is connected to external power and the battery is charging. ● Off: (4) Vent ◦ The computer is not connected to external power.
Component Description (2) Enables airflow to cool internal components. Vent NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (3) External monitor port Connects an external VGA monitor or projector. (4) RJ-45 (network) jack Connects a network cable. (5) HDMI port Connects an optional HDMI device.
Component Description (1) Internal display switch Turns off the display if the display is closed while the power is on. (2) Internal microphone Records sound. (3) Webcam light (select models only) On: The webcam is in use. (4) Webcam (select models only) Records video and captures still photographs. Wireless antennas (select models only) The antennas send and receive signals from one or more wireless devices. These antennas are not visible from the outside of the computer.
Component Description (1) WWAN antennas (2)* Send and receive wireless signals to communicate with wireless wide area networks (WWANs). (2) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLANs). *The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions.
Additional hardware components Component Description (1) Power cord* Connects an AC adapter to an AC outlet. (2) Battery* Powers the computer when the computer is not plugged into an external power source. (3) AC adapter Converts AC power to DC power. *Batteries and power cords vary in appearance by country or region.
Have this information available when you contact technical support. The service tag label is affixed to the bottom of the computer. ● Regulatory label—Provides regulatory information about the computer. The regulatory label is affixed to the bottom of the computer. ● Modem approval label—Provides regulatory information about the modem and lists the agency approval markings required by some of the countries in which the modem has been approved for use.
2 Pointing devices and keyboard Using pointing devices Setting pointing device preferences Use Mouse Properties or TouchPad to customize settings for pointing devices, such as button configuration, click speed, and pointer options. To access Mouse Properties, select Computer > Control Center > Mouse. To access TouchPad properties, select Computer > Control Center > TouchPad. Connecting an external mouse You can connect an external USB mouse to the computer using one of the USB ports on the computer.
Function Hotkey Initiate Sleep. fn+f1 Decrease screen brightness. fn+f2 Increase screen brightness. fn+f3 Switch the screen image. fn+f4 Open the default e-mail client. fn+f5 Open the default Web browser. fn+f6 Mute speaker sound. fn+f7 Decrease volume speaker sound. fn+f8 Increase volume speaker sound. fn+f9 Play previous track. fn+f10 Play, pause, or resume a CD, DVD, or BD. fn+f11 Play next track.
Switching the screen image Press fn+f4 to switch the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, pressing fn+f4 alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor. Most external monitors receive video information from the computer using the external VGA video standard.
Playing the next track or section of an audio CD or a DVD While an audio CD or a DVD is playing, press fn+f12 to play the next track of the CD or the next section of the DVD. Using the embedded numeric keypad The 15 keys of the embedded numeric keypad can be used like the keys on an external keypad. When the embedded numeric keypad is turned on, each key on the keypad performs the function indicated by the icon in the upper-right corner of the key.
Clean the keyboard regularly to prevent keys from sticking and to remove dust, lint, and particles that can become trapped beneath the keys. A can of compressed air with a straw extension can be used to blow air around and under the keys to loosen and remove debris.
3 Multimedia Multimedia features Your computer includes multimedia features that allow you to listen to music, watch movies, and view pictures.
Component Description (1) Internal microphone Records sound. (2) Webcam Records video and captures still photographs. (3) Speakers (2) Produce sound. (4) Audio-out (headphone) jack Produces sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio. NOTE: When a device is connected to the headphone jack, the computer speakers are disabled.
◦ ● To increase volume, press and hold the fn key (1), and then tap the volume up key f9 (4) until the desired volume level is reached. Operating system volume control: a. Click the Volume icon in the notification area, at the far right of the taskbar. b. Increase or decrease the volume by moving the slider up or down. – or – a. Right-click the Volume icon to view volume options, such as Mute, Volume Control, and Preferences. b. Right-click the Volume icon to launch Volume Control.
CAUTION: To prevent loss of information or damage to a disc, observe the following guidelines: Before writing to a disc, connect the computer to a reliable external power source. Do not write to a disc while the computer is running on battery power. Before writing to a disc, close all open programs except the disc software you are using. Do not copy directly from a source disc to a destination disc or from a network drive to a destination disc.
To connect external devices, such as external speakers, headphones, or a microphone, refer to the information provided with the device. For best results, remember the following tips: ● Be sure that the device cable is securely connected to the correct jack on your computer. (Cable connectors are normally color-coded to match the corresponding jacks on the computer.) ● Be sure to install any drivers required by the external device.
▲ To connect a display device, connect the device cable to the external monitor port. NOTE: If a properly connected external display device does not display an image, press fn+f4 to transfer the image to the device. Repeatedly pressing fn+f4 alternates the screen image between the computer display and the device. Using the HDMI port Select computer models include an HDMI (High Definition Multimedia Interface) port.
To connect a video or audio device to the HDMI port: 1. Plug one end of the HDMI cable into the HDMI port on the computer. 2. Connect the other end of the cable to the video device, according to the device manufacturer's instructions. 3. Press fn+f4 to switch the image between the display devices connected to the computer. Optical drive (select models only) Depending on the type of optical drive and software installed in your computer, the optical drive plays, copies, and creates CDs, DVDs, or BDs.
Optical drive type Blu-ray R/RE DVD+/RW SuperMulti DL Drive* Write to CDRW Write to DVD±RW/ R Yes Write to DVD±R DL Yes Write label to LightScribe CD or DVD ±RW/R Yes No Write to BD R/RE Yes *Double-layer discs can store more data than single-layer discs. However, double-layer discs burned with this drive may not be compatible with many single-layer DVD drivers and players. † LightScribe discs must be purchased separately.
DVD±R discs Use blank DVD±R discs to permanently store large amounts of information. After data is recorded, it cannot be erased or written over. DVD±RW discs Use DVD±RW discs if you want to be able to erase or write over data that you saved earlier. This type of disc is ideal for testing audio or video recordings before you burn them to a CD or DVD that cannot be changed. LightScribe DVD+R discs Use LightScribe DVD+R discs for sharing and storing data, home videos, and photos.
5. Gently press the disc (3) down onto the tray spindle until the disc snaps into place. 6. Close the disc tray. 7. Select Computer > More Applications. 8. Open an audio player, such as Helix Banshee, to play the disc. NOTE: After you insert a disc, a short pause is normal. If Suspend or Hibernation is initiated during playback of a disc, you may experience the following behaviors: ● Your playback may be interrupted. ● You may see a warning message asking if you want to continue.
2. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces. NOTE: If the tray is not fully accessible, tilt the disc carefully as you remove it. 3. Close the disc tray and place the disc in a protective case. The optical disc tray does not open for removal of a CD, DVD, or BD 1. Insert the end of a paper clip (1) into the release access in the front bezel of the drive. 2.
3. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces. NOTE: If the tray is not fully accessible, tilt the disc carefully as you remove it. 4. Close the disc tray and place the disc in a protective case. Webcam Your computer includes an integrated webcam, located at the top of the display.
4 Power management Setting power options Using power-saving states The computer has two power-saving states enabled at the factory: Suspend and Hibernation. When Suspend is initiated, the power light blinks and the screen clears. Your work is saved to memory, letting you exit Suspend faster than exiting Hibernation. If the computer is in the Suspend state for an extended period or if the battery reaches a critical battery level while in the Suspend state, the computer initiates Hibernation.
Using the Power icon The Power icon is located in the notification area, at the far right of the taskbar. The Power icon allows you to quickly access power settings, view remaining battery charge, and then select a different power plan. ● To display the percentage of remaining battery charge, click the Power icon, and then click Information. ● To access Power Management Preferences, click the Power icon, and then click Preferences.
Connecting the AC adapter WARNING! To reduce the risk of electric shock or damage to the equipment: Plug the power cord into an AC outlet that is easily accessible at all times. Disconnect power from the computer by unplugging the power cord from the AC outlet (not by unplugging the power cord from the computer). If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3pin outlet.
WARNING! To reduce potential safety issues, use only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased from HP. Computer battery life varies, depending on power management settings, programs running on the computer, display brightness, external devices connected to the computer, and other factors. Inserting or removing the battery CAUTION: Removing a battery that is the sole power source can cause loss of information.
3. Remove the battery (2). Charging a battery WARNING! Do not charge the computer battery while you are onboard an aircraft. The battery charges whenever the computer is plugged into external power through an AC adapter, an optional power adapter, an optional expansion product, or an optional docking device (select models only). The battery charges whether the computer is off or in use, but it charges faster when the computer is off.
Maximizing battery discharge time Battery discharge time varies, depending on the features you use while on battery power. Maximum discharge time gradually shortens as the battery storage capacity naturally degrades. Tips for maximizing battery discharge time: ● Lower the brightness on the display. ● Remove the battery from the computer when it is not being used or charged. ● Store the battery in a cool, dry location. ● Select the Powersave setting in Power Management.
Resolving a low battery level when a charged battery is available 1. Turn off the computer or initiate Hibernation. 2. Remove the discharged battery, and then insert a charged battery. 3. Turn on the computer. Resolving a low battery level when no power source is available ▲ Initiate Hibernation. – or – Save your work and shut down the computer. Resolving a low battery level when the computer cannot exit Hibernation When the computer lacks sufficient power to exit Hibernation, follow these steps: 1.
Step 2: Disable Hibernation and Suspend 1. Click the Power icon, located on the far right of the taskbar, and then click Preferences. 2. Under the Running on AC and Running on Battery tabs, record the current values for the following settings: ● Put the display to Suspend when the computer is inactive for: ● Put the computer to Suspend when it is inactive for: 3. Change all 4 settings to Never. 4. Click Close.
Step 5: Reenable Hibernation and Suspend CAUTION: Failure to reenable Hibernation after calibration may result in a full battery discharge and information loss if the computer reaches a critical battery level. 1. Click the Power icon, located on the far right of the taskbar, and then click Preferences. 2. Under the Running on AC and Running on Battery tabs, reset the previously recorded values for the following settings: 3.
Replacing the battery Computer battery life varies, depending on the power management settings, programs running on the computer, display brightness, external devices connected to the computer, and other factors. Battery Check notifies you to replace the battery when an internal cell is not charging properly, or when the battery storage capacity has reached a “weak” condition. A message refers you to the HP Web site for more information about ordering a replacement battery.
If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try the following emergency procedures in the sequence provided: ● Press and hold the power button for at least 5 seconds. ● Disconnect the computer from external power and remove the battery.
5 Drives Handling drives Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply.
● DVD-ROM Drive ● DVD+/-RW SuperMulti Double-Layer LightScribe Drive ● Blu-ray ROM DVD+/-RW SuperMulti Double-Layer LightScribe Drive Using optional external devices NOTE: For more information about required software and drivers, or to learn which computer port to use, refer to the manufacturer's instructions.
7. Remove the screws from the battery area. NOTE: Refer to the illustration that most closely matches your computer.
8. Remove the 2 screw covers (1) and screws (2) from the back edge of the computer. NOTE: Some models do not have any screw covers or screws to remove. 9. Turn the computer display-side up, and then open the computer as far as possible. CAUTION: Do not use excessive force to open the computer beyond the limits of the display hinges. Forcing extension beyond these limits will cause damage to the display. 10.
11. Remove the screws from the keyboard. NOTE: Refer to the illustration that most closely matches your computer.
12. Slide the keyboard back toward the display (1), and then rotate it forward (2) to gain access to the keyboard cable connector. NOTE: Refer to the illustration that most closely matches your computer. CAUTION: Do not rip the keyboard cable. – or – Slide the keyboard back toward the display (1), and then rotate it to the right side (2) to gain access to the keyboard cable connector. CAUTION: Do not rip the keyboard cable.
13. Release the ZIF connector (1) to which the keyboard cable is attached, disconnect the keyboard cable (2) from the system board by pulling upward, and then remove the keyboard from the computer (3). NOTE: Refer to the illustration that most closely matches your computer.
14. Remove the screws from the palm rest. 15. Slide the palm rest to the right until it disengages from the base enclosure (1), and then rest the palm rest on the computer (2). 16. Remove the 2 hard drive screws (1), and then loosen the captive screw (2) that secures the hard drive. 17. Use the plastic tab (3) on the hard drive to slide the hard drive to the right to disconnect it from the system board.
18. Lift the hard drive (4) out of the hard drive bay. To install a hard drive: 50 1. Insert the hard drive into the hard drive bay (1). 2. Use the plastic tab (2) on the hard drive to slide the hard drive to the left to connect it to the system board. 3. Replace the 2 hard drive screws (3), and then tighten the captive screw (4) to secure the hard drive to the computer.
4. Turn over the palm rest (1), resting it in the palm rest tray, and then slide the palm rest to the left to reconnect it to the base enclosure (2). 5. Replace the screws in the palm rest. 6. Place the keyboard upside down on the palm rest of the computer (1).
7. Insert the keyboard cable (2) into the ZIF connector (3) on the system board, and then secure the connector. NOTE: Refer to the illustration that most closely matches your computer.
8. Turn over the keyboard (1) into the keyboard tray, and then slide the keyboard (2) into place. NOTE: Refer to the illustration that most closely matches your computer.
9. Replace the screws on the keyboard. NOTE: Refer to the illustration that most closely matches your computer.
10. Place the switch cover on top of the switch cover tray (1), and then slide the switch cover into place (2). 11. Close the computer display. 12. Turn the computer upside down on a flat surface, with the battery bay toward you. 13. Replace the 2 screws (1) and their covers (2) on the back edge of the computer. NOTE: Some models do not have any screws or screw covers to replace.
14. Replace the screws in the battery area. NOTE: Refer to the illustration that most closely matches your computer. 15. Replace the battery. 16. Turn the computer right-side up, and then reconnect external power and external devices. 17. Turn on the computer.
6 External devices Using a USB device Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Some USB devices may require additional support software, which is usually included with the device. For more information about device-specific software, refer to the manufacturer's instructions. Your computer model has 4 USB ports, which support USB 1.0, USB 1.1, and USB 2.0 devices.
Using USB legacy support USB legacy support (enabled by default) permits the following actions: ● Using a USB keyboard, mouse, or hub connected to a USB port on the computer during startup or in an MS-DOS-based program or utility ● Starting or restarting from an optional external MultiBay or an optional USB bootable device USB legacy support is enabled at the factory. To disable or enable USB legacy support: 1.
2. Connect the eSATA cable for the device to the eSATA port. Once connection has been established, an authentication window opens on the screen asking for the root password. 3. Enter the root password, and then the system auto-mounts the eSATA device and an icon is placed on the desktop. Stopping and removing an eSATA device CAUTION: To prevent loss of information or an unresponsive system, stop the eSATA device before removing it.
To connect an external device to the computer: CAUTION: To reduce the risk of damage to the equipment when connecting a powered device, be sure that the device is turned off and the AC power cord is unplugged. 1. Connect the device to the computer. 2. If you are connecting a powered device, plug the device power cord into a grounded AC outlet. 3. Turn on the device. To disconnect an unpowered external device, turn off the device, and then disconnect it from the computer.
7 External media cards Using Media Card Reader cards Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital media-equipped cameras and PDAs, as well as with other computers.
Removing a digital card CAUTION: To prevent loss of data or an unresponsive system, be sure that you are not accessing the digital card before removal. 1. Save your information and close all programs associated with the digital card. NOTE: Refer to the digital card user documentation for complete instructions on safe card removal. 2. Press in on the digital card (1), and then remove it from the slot (2).
2. Pull the insert out of the slot (2). To insert an ExpressCard: 1. Hold the card label-side up, with the connectors facing the computer. 2. Insert the card into the ExpressCard slot, and then push in on the card until it is firmly seated. NOTE: An inserted ExpressCard uses power even when idle. To conserve power, stop or remove an ExpressCard when it is not in use.
64 Chapter 7 External media cards
8 Memory modules The computer has one memory module compartment, which is located under the keyboard. The memory capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot. All memory modules installed in the computer must be the same type. When upgrading memory capacity, verify that the upgrade modules are the same as those already installed in the computer.
7. Remove the screws from the battery area. NOTE: Refer to the illustration that most closely matches your computer.
8. Remove the 2 screw covers (1) and screws (2) from the back edge of the computer. NOTE: Some models do not have any screw covers or screws to remove. 9. Turn the computer display-side up, and then open the computer as far as possible. CAUTION: Do not use excessive force to open the computer beyond the limits of the display hinges. Forcing extension beyond these limits will cause damage to the display. 10.
11. Remove the screws from the keyboard. NOTE: Refer to the illustration that most closely matches your computer.
12. Slide the keyboard back toward the display (1), and then rotate it forward (2) to gain access to the keyboard cable connector. NOTE: Refer to the illustration that most closely matches your computer. CAUTION: Do not rip the keyboard cable. – or – Slide the keyboard back toward the display (1), and then rotate it to the right side (2) to gain access to the keyboard connector. CAUTION: Do not rip the keyboard cable. 13.
b. Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot. To protect a memory module after removal, place it in an electrostatic-safe container. 14. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. a. Align the notched edge (1) of the memory module with the tab in the memory module slot. b.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place.
15. Turn over the keyboard (1) into the keyboard tray, and then slide the keyboard (2) into place. NOTE: Refer to the illustration that most closely matches your computer.
16. Replace the screws on the keyboard. NOTE: Refer to the illustration that most closely matches your computer.
17. Place the switch cover on top of the switch cover tray (1), and then slide the switch cover into place (2). 18. Close the computer display. 19. Turn the computer upside down on a flat surface, with the battery bay toward you. 20. Replace the 2 screws (1) and their covers (2) on the back edge of the computer. NOTE: Some models do not have any screws or screw covers to replace.
21. Replace the screws in the battery area. NOTE: Refer to the illustration that most closely matches your computer. 22. Replace the battery. 23. Turn the computer right-side up, and then reconnect external power and external devices. 24. Turn on the computer.
9 Security NOTE: Some of the features described in this chapter may not be supported by your computer or your operating system. Protecting the computer NOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. Security features provided with your computer can protect the computer, personal information, and data from a variety of risks. The way you use your computer will determine which security features you need to use.
● If you forget the setup password set in Computer Setup, you will not be able to access the utility. ● If you have the stringent security feature enabled in Computer Setup and you forget the setup password, the computer is inaccessible and can no longer be used. Call technical support or your authorized service provider for additional information. ● If you forget the setup password set in Computer Setup, you cannot turn on the computer or exit Hibernation.
Note the following characteristics of the setup password: ● It is not interchangeable with an operating system root password, although both passwords can be identical. ● It is not displayed as it is set, entered, changed, or deleted. ● It must be set and entered with the same keys. For example, a setup password set with keyboard number keys will not be recognized if you enter it thereafter with embedded numeric keypad number keys.
To apply DriveLock protection to an internal hard drive, a user password and a master password must be set in Computer Setup. Note the following considerations about using DriveLock protection: ● After DriveLock protection is applied to a hard drive, the hard drive can be accessed only by entering either the user password or the master password. ● The owner of the user password should be the day-to-day user of the protected hard drive.
3. Use the arrow keys to select the location of the internal hard drive, and then press f10. 4. Use the arrow keys to select the field for the password you want to change. Type your current password in the Old password field, and then type the new password in the New password field and in the Verify new password field. Then press f10. 5. To save your preferences, use the arrow keys to select File > Save changes and exit. Then follow the instructions on the screen.
The stringent security feature enhances power-on security by forcing user authentication with your configured setup password or smart card PIN before granting access to the system. Setting stringent security To enable stringent security in Computer Setup, follow these steps: 1. Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the “F10 = ROM Based Setup” message is displayed in the lower-left corner of the screen. 2.
Using firewall software When you use the computer to access e-mail, a network, or the Internet, unauthorized persons may be able to gain access to information about you, the computer, and your personal files. Use the firewall software preinstalled on the computer to protect your privacy: ▲ Select Computer > Control Center > YaST > Security and Users > Firewall. Firewall features include information on logging and reporting, and automatic alarms to monitor all incoming and outgoing traffic.
NOTE: The location of the security cable slot varies by computer model.
10 Computer Setup Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer or your operating system. NOTE: Pointing devices are not supported in Computer Setup. You must use the keyboard to navigate and make selections.
Your preferences go into effect when the computer restarts. Restoring factory settings in Computer Setup To return all settings in Computer Setup to the values that were set at the factory, follow these steps: 1. Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the "F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen. 2. Use the arrow keys to select File > Restore Defaults, and then press enter. 3.
Select To do this Setup Password Enter, change, or delete a setup password. Password Options ● Enable/disable stringent security. ● Enable/disable the password requirement on computer restart. ● Enable/disable DriveLock on any computer hard drive. ● Enter, change, or disable DriveLock on an optional MultiBay hard drive. DriveLock Passwords NOTE: DriveLock settings are accessible only when you enter Computer Setup by turning on (not restarting) the computer.
System Configuration menu NOTE: Some of the menu items listed in this section may not be supported by your computer or your operating system. Select To do this Language Change the Computer Setup language. Boot options ● Set an f9, f10, and f12 delay when starting up. ● Enable/disable CD-ROM boot. ● Enable/disable floppy boot. ● Enable/disable internal network adapter boot. ● Enable/disable MultiBoot, which sets a boot order that can include most boot devices in the system.
Select To do this Built-in device options ● Enable/disable embedded WLAN Device Radio. ● Enable/disable embedded Bluetooth Device Radio. ● Enable/disable Network Interface Controller (NIC) ● Enable/disable LAN/WLAN Switching. ● Enable/disable Wake on LAN. ● Enable/disable the integrated camera (webcam) ● Enable/disable USB port. ● Enable/disable ExpressCard slot.
Index A AC adapter connecting 33 identifying 12 AC adapter light, identifying 7, 8 airport security devices 42 antennas WLAN 11 WWAN 11 audio devices, connecting external 22 audio functions, checking 23 audio-in (microphone) jack, identifying 6, 20 audio-out (headphone) jack, identifying 6, 20 automatic updates, software 82 B battery charging 35 disposing 39 inserting 34 removing 34 replacing 40 storing 39 battery bay 9, 13 battery charge, maximizing 36 battery light 35 battery power 33 battery release latc
E e-mail application hotkey 16 e-mail client light, identifying 2 earbuds 20 embedded keypad keys, identifying 5 eSATA cable, connecting 58 eSATA devices connecting 58 description 58 removing 59 stopping 59 eSATA port, identifying 8, 9 esc key, identifying 5, 6 ExpressCard configuring 62 inserting 62 removing 63 removing insert 62 ExpressCard slot, identifying 8, 9 external audio devices, connecting 22 external drive 42, 59 external monitor port, identifying 8, 9, 23 F File menu 85 fingerprint reader, ident
using 26 writing to 22 optical drive identifying 7 protecting 22 optical drive light, identifying 7 P passwords DriveLock 78 root 77 setup 77 user 77 pointing devices setting preferences 14 ports eSATA 8, 9, 58 external monitor 8, 9, 23 HDMI 8, 9, 24 USB 7, 8, 9, 57 power connecting 33 power button, identifying 4 power connector, identifying 7, 8 power cord, identifying 12 power light, identifying 3 power management 32 product name and number, computer 12 projector, connecting 23 R readable media 31 regul
