HP LaserJet Managed MFP E72525, E72530, E72535, E72825, E72830, E72835 - Engine Install Guide

ManualsBrandsHP ManualsDesktopsHP LaserJet Managed Flow MFP E72525-E72535z - Base Product 25-35 ppm

NJ

OE

support.hp.com

1.1 1.2

Engine Install Guide

WARNING: Make sure the work area is free of debris

and the oor is not slippery or wet.

CAUTION: The printer assembly is heavy. Four people

must lift and install it on the dual cassette feeder (DCF)

(Y1F97A), the 2000-sheet high capacity input (HCI)

(Y1F99A), or the stand (Y1G17A).

Unpack and acclimate the printer.

CAUTION: Before the printer is powered on, make sure that the room and equipment are at least 15°C (59°F).

NOTE: Leave the printer on the shipping pallet until it is ready to install on a DCF, HCI, or stand.

Remove the printer, imaging drum, toner collection unit (TCU), and associated hardware from the

box. After unpacking the printer and supplies, allow them to acclimate for four hours.

NOTE: If the printer and hardware were stored below 0°C (32°F), it may take them longer to acclimate.

CAUTION: Do not remove the shipping tape or protective packing materials until after the printer

is installed on a DCF, HCI, or stand. (Step 3.2)

NOTE: The imaging drum is stored in the output bin area below the automatic document feeder.

Pull the protective clear plastic down to the base of the printer

toallow access to lifting points.

HP recommends reviewing

the video before performing

the installation.

TopazOnly_Engine_IG 4languages_.indd 1 3/1/2019 8:23:08 PM

HP LaserJet Managed MFP E72825, E72830, E72835

HP LaserJet Managed MFP E72525, E72530, E72535

https://www.hp.com/videos/A3install

Summary of content (9 pages)

PAGE 1
HP LaserJet Managed MFP E72825, E72830, E72835 HP LaserJet Managed MFP E72525, E72530, E72535 NJ OE Engine Install Guide support.hp.com WARNING: Make sure the work area is free of debris and the floor is not slippery or wet. CAUTION: The printer assembly is heavy. Four people must lift and install it on the dual cassette feeder (DCF) (Y1F97A), the 2000-sheet high capacity input (HCI) (Y1F99A), or the stand (Y1G17A). https://www.hp.
PAGE 2
Prepare the DCF, 2000-sheet HCI, or stand for installation. CAUTION: Use care when lifting. Use proper safe lifting practices. IMPORTANT: Retain two thumbscrews for securing the HCI or stand. 2.1 Follow the in-box directions to unpack the DCF, HCI, or stand. If the Stapler-Stacker (Y1G18A) or Booklet Finisher (Y1G07A) will be installed, the HP LaserJet Spacer (Y1G24A) must be installed on the bottom of the DCF, HCI, or stand. If the spacer is not required, go to step 2.7. 2.
PAGE 3
.2 NJ Carefully lift the printer assembly and align the printer to the alignment pins and connector on the accessory. Carefully lower the printer onto the accessory. CAUTION: The printer assembly is heavy. Four people must lift and install it on the DCF, the HCI, or the stand. NOTE: On the printer, open each door and all of the trays to check for shipping tape and packing materials. Remove all shipping tape and protective packing materials.
PAGE 4
5 Install the toner cartridge. 5.1 5.2 5.4 5.5 Open the front and right doors. NOTE: Leave the doors open until the toner cartridge, imaging drum, and the toner collection unit (TCU) are installed. Install the toner cartridge. 6 Remove the toner cartridge packaging. Shake the cartridge side-to-side (about five times) to distribute the toner throughout the cartridge. 5.
PAGE 5
6.6 Remove the orange plug from the imaging unit. Tighten one thumb screw. 6.7 Pull straight out on the red arrow tab to remove the seal at the front of the imaging unit. Slide the imaging unit into the device. Hold the imaging unit with one hand on the bottom and the other hand on the gray handle at the front. 6.9 6.8 6.10 Push and hold the imaging unit in place while installing the first screw (callout 1) to secure the imaging unit. Install the second screw (callout 2). 6.
PAGE 6
9 Load paper in Tray 2. NOTE: Paper is used to print configuration sheets as needed (Letter or A4). 9.1 9.2 Push down on the blue tab in the back of the tray. At the same time, pinch or squeeze the blue tab in the front of the tray and slide to adjust to the proper paper length. Both tabs are spring-loaded and will lock, once released. 9.3 Squeeze the sides of the tab, and then slide to adjust the paper width. 9.4 Load the paper.
PAGE 7
11 Late point differentiation configuration (LPDC) checklist (automatic). CAUTION: The LPDC procedure must be performed by a trained person during the device install, staging or, setup process. NOTE: If no internet connection is available, or the LPDC process is not possible via the network connection, the speed license can be downloaded to a USB flash drive and manually installed. Go to Step 12. NOTE: Wait 24-48 hours from the time the unit is shipped to when the license becomes available in the cloud.
PAGE 8
12 Late point differentiation configuration (LPDC) checklist (manually using USB flash drive). • Make sure that the network cable is disconnected from the printer. • Turn on the main power switch (near the power cord), and then press the power button on the front of the printer to turn the power on. • Download the speed license to a USB flash drive. • With an internet-connected PC, open a browser and go to the HP Jet Advantage Management (JAM) Activation site: https://activation.jamanagement.hp.
PAGE 9
13 Install the model nameplate and barcode label. NOTE: The model nameplates are included in the large box that contained the CD, power cord, tray labels, and other items. 13.1 14 13.2 Find the bar code that matches the model nameplate and then install the new bar code label on the inside of the front cover of the printer. 13.3 Install the nameplate. Install the stabilization blocks. 14.1 14.2 © Copyright 2020 HP Development Company, L.P. www.hp.com 9 TopazOnly_Engine_IG 4languages_.