HP DesignJet z9+ PostScript Printer - Assembly instructions

ManualsBrandsHP ManualsDesktopsHP DesignJet Z9+dr 44-in PostScript Printer with V-Trimmer TAA Compliant

Large Format Division

Camí de Can Graells 1-21 · 08174

Sant Cugat del Vallès

Barcelona · Spain

Printed in XXX

HP DesignJet Z9

Printer Series

Assembly instructions

Instructions d’assemblage

Anleitung zum Zusammenbau

Istruzioni per l’installazione

Instrucciones de montaje

Instruções de montagem

Instructies voor het opstellen



*X9D24-90033*

X9D24-90033

Hardware Setup:

1- Assemble the stand

2- Attach the printer body to the stand assembly

3- Set up the printer

4- Printhead and cartridge setup

5- Connectivity & Mobile Printing

Software setup:

Now, it’s easy to print large-format documents from virtually anywhere,

using your laptop, printer touchscreen, iPhone®, or iPad®.

Install the product software from www.hp.com/go/Z9/drivers

Installation du matériel :

1- Assemblage du support

2- Fixation de l’imprimante au support

3- Conguration de l’imprimante

4- Installation des têtes d’impression et des cartouches

5- Connectivité et impression mobile

Installation du logiciel :

Il est désormais facile d’imprimer des documents grand format depuis

quasiment n’importe où à l’aide d’un ordinateur portable, de l’écran tactile

de l’imprimante, d’un iPhone® ou d’un iPad®.

Installation du logiciel du produit à partir dewww.hp.com/go/Z9/drivers

Hardware-Setup:

1- Zusammenbauen des Standfußes

2- Aufsetzen des Druckers auf den

Standfuß

3-Einrichten des Druckers

4- Einrichten von Druckköpfen und Patronen

5- Verbindung und HP Mobile Printing

Software-Setup:

Das Drucken großformatiger Dokumente von nahezu jedem Standort aus

mit Ihrem Notebook, Drucker-Touchscreen,

iPhone® oder iPad® ist nun einfacher denn je.

Installieren Sie die Produktsoftware von: www.hp.com/go/Z9/drivers

Installazione dell’hardware:

1- Assemblaggio del piedistallo

2- Fissare il corpo della

stampante al piedistallo

3-Installazione della stampante

4 - Installazione delle cartucce e delle testine di stampa

5- Connettività e soluzioni “mobili” per la stampa

Impostazione del software:

Ora è semplice stampare documenti di grande formato da praticamente

qualsiasi posizione utilizzando il laptop, lo schermo a soramento della

stampante, l’iPhone® o l’iPad®.

Installare il software del prodotto da: www.hp.com/go/Z9/drivers

Instalación del hardware:

1- Montaje del soporte

2- Una la estructura de la

impresora al conjunto del soporte

3-Conguración de la impresora.

4- Instalación del cabezal de impresión y el cartucho

5-Conectividad e impresión desde dispositivos móviles

Instalación del software:

Ahora resulta muy fácil imprimir documentos de gran formato desde

prácticamente cualquier lugar mediante un portátil, la pantalla táctil de

la impresora, un iPhone® o un iPad®.

Instale el software del producto desde: www.hp.com/go/Z9/drivers

Conguração de hardware:

1- Monte a base

2- Conecte a impressora à

montagem da base

3- Instalar a impressora

4 - Conguração de cartucho de tinta e cabeçotes de impressão

5- Conectividade e impressão móvel

Conguração de software:

Agora, é fácil imprimir documentos em grandes formatos de

praticamente qualquer lugar usando olaptop, a tela sensível ao toque

da impressora, o iPhone® ou o iPad®.

Instale o software do produto pelo site: www.hp.com/go/Z9/drivers

Installatie van de hardware:

1- De voet in elkaar zetten

2- Bevestig het hoofdbestanddeel van de printer aan de gemonteerde

staander

3- De printer opstellen

4- Installatie van printkop en cartridge

5- Connectiviteit en mobiel afdrukken

Installatie van de software:

Nu kunt u eenvoudig documenten van groot formaat vanaf vrijwel elke

locatie af te drukken, met behulp van uw laptop,

uw printertouchscreen, iPhone® of iPad®.

Installeer de productsoftware via: www.hp.com/go/Z9/drivers























®iPhone ®iPad.

www.hp.com/go/Z9/drivers

Summary of content (28 pages)

PAGE 1
HP DesignJet Z9 Printer Series EN Hardware Setup: 1- Assemble the stand 2- Attach the printer body to the stand assembly 3- Set up the printer 4- Printhead and cartridge setup 5- Connectivity & Mobile Printing EN Assembly instructions FR Instructions d’assemblage Software setup: Now, it’s easy to print large-format documents from virtually anywhere, using your laptop, printer touchscreen, iPhone®, or iPad®. DE Anleitung zum Zusammenbau Install the product software from www.hp.
PAGE 2
1 Product working area Before you start unpacking, consider where you are going to put the assembled product. You should allow some clear space on all sides of the product box. The recommended clearances are shown in the illustration. • To assemble the product you will need at least 3 x 3 m (118 x 118 in) of empty floor space. • Time required to assemble the printer is approximately 110 minutes. EN Please read these instructions carefully.
PAGE 3
EN FR DE IT ES PT NL 4 5 1 Assemble the stand Assemblage du support Zusammenbauen des Standfußes Assemblaggio del piedistallo Montaje del soporte Monte a base De voet in elkaar zetten ‫تجميع الحامل‬ AR X8 40’ EN Locate the stand pieces and remove the following: 1. Right leg / 2. Basket frame / 3. Right foot / 4. Screwdriver and screws / 5. Cross brace / 6. Left foot / 7. Left leg / 8. Cross bar (Z9+ 44” only). Fix one foot to a leg with 8 screws. Repeat the process for the other foot and leg.
PAGE 4
7 6 EN 8 9 Slot a leg onto the cross brace to install the leg with the long side of the foot as shown in the image. Important: Note that there are stickers on the legs, make sure the letters match the ones on the cross brace (R with R, L with L). Fix the leg to the cross brace with 3 screws at the inner face of the leg. Important: Do not fully tighten them. Slot the other leg onto the cross brace making sure that the basket supports located on the feet (1 on each foot) are on the same side.
PAGE 5
11 10 12 13 X2+2 EN HP DesignJet Z9+ 44” only: Fix the cross bar to the bottom of the legs with 4 screws (2 each side). Turn the stand upright. Attach the outside of the leg to the cross brace with 2 screws. Repeat the process with the other leg. Fully tighten all the stand’s screws. At this point two spare screws should remain. FR Modèle HP DesignJet Z9+ 44 pouces uniquement: Fixez la barre transversale en bas des pieds à l’aide de 4 vis (2 de chaque côté).
PAGE 6
15 14 EN FR DE IT ES PT EN To finish the stand assembly check that the 4 wheels are locked.
PAGE 7
18 17 19 20 EN Remove the small flaps from each of the foam end pieces. Do not remove the foam end pieces. Remove the tape from the transparent covering that protects the product. Open the transparent covering and remove the desiccant bag from the top of the product. There is a round yellow button protruding from the top of one stand leg, and a square green button protruding from the top of the other leg. Each button fits into a hole in the product.
PAGE 8
21 22 23 24 EN Place the stand on the product slowly and carefully, so that the colored buttons on the legs fit into the corresponding holes in the product. IMPORTANT: Make sure there is nothing on top of the printer body before continuing. Locate the 4 black screws. Fix the printer to the stand from underneath with the 4 black screws. Check that the wheels on the stand are locked.
PAGE 9
26 25 27 28 EN Make sure there is nothing on the printer. Rotate the product 90°. IMPORTANT: While you rotate, keep the roll feeds face downwards. You may need a third person. Hold the product by the foam end pieces and rotate it until it stands on its feet, with all four wheels in contact with the floor. The 24’ inch models weigh about 70 kg ( 154 lb ) and the 44’ inch models weigh about 90 kg (198 lb). Remove the foam end pieces. Remove the transparent covering from the product.
PAGE 10
29 EN 31 30 32 Install the pocket at the back of the printer. Remove the tape from the stand, and unfold the fabric. Pass the fabric through to the front of the printer and then insert the frame. Check the picture for correct installation. Clip the basket frame to the feet. Press firmly until it clicks into place. The basket is now complete. FR Installez le bac à l’arrière de l’imprimante. Retirez les bandes adhésives et dépliez le tissu.
PAGE 11
33 EN FR DE IT ES PT NL 34 35 3 Set up the printer Configuration de l’imprimante Einrichten des Druckers Installazione della stampante Configuración de la impresora Instalar a impressora De printer opstellen ‫إعداد الطابعة‬ AR 15’ EN Remove the orange tape pieces from the product, except for the ones coming from inside the product. HP DesignJet Z9+dr PostScript Printer: Carefully remove the cardboard from the output platen.
PAGE 12
36 37 38 39 90º EN You will see a cardboard support attached to the product with tape. Remove the tape. Turn the cardboard support 90° to the right. CAUTION: Avoid hitting the belts. Carefully lift the cardboard support up and out of the product. It will not be needed again; you can discard it. Repeat steps 36 to 37 in case you find a second cardboard support like the one removed.
PAGE 13
40 41 42 43 7-15’ EN Part of the stopper may fall off while being removed, if this happens remove both parts. The stopper will not be needed again, you can discard it. Remove the orange tapes and unlock the wheels. Move the printer to its final destination. Connect the network cable. If you find a USB flash drive in a plastic bag inside the box, it contains the latest Firmware. Please follow the instructions in the bag. Otherwise, please ignore this step.
PAGE 14
45 44 46 EN Connect the power cable to the printer, and the outlet. Remove the plastic film covering the window and the plastic film covering the front panel (LCD display). When all cables are connected, switch the printer on. On the front panel, the HP logo appears. Please wait a while. You will then be prompted to select the language of the product. If USB flash drive is found, follow the front panel instructions. FR Branchez le câble d’alimentation à l’imprimante et la prise.
PAGE 15
47 EN FR DE IT ES PT NL 4 Printhead and cartridge setup Installation des têtes d’impression et des cartouches Einrichten von Druckköpfen und Patronen Installazione delle cartucce e delle testine di stampa Instalación del cabezal de impresión y el cartucho Configuração de cartucho de tinta e cabeçotes de impressão Installatie van printkop en cartridge ‫ تعيين إعدادات الخرطوشة ورأس‬AR ‫الطباعة‬ 48 49 EN When prompted by the front panel to insert the ink cartridges, open both the left-hand and right-
PAGE 16
51 50 52 53 10’ EN The printer now prepares the ink system for use. Please wait until it has completed before you continue. When the ink system is ready, the front panel will prompt you to open the window and printhead cover. Open the window and pull the blue printhead cover handle up and towards you to release the latch. Push the handle back to raise the lid to access the setup printheads. FR L’imprimante va maintenant préparer le système d’encre aux fins d’utilisation.
PAGE 17
55 54 56 57 EN Look at each setup printhead to verify that it has ink inside. The setup printheads only purpose is to prevent ink loss during ink cartridge installation. Remove and discard all the setup printheads. You may need to use force to extract each printhead. The setup printheads contain ink, which could leak out. Avoid touching pins, leads or circuits. When all of the setup printheads have been removed, press “Next”on the front panel.
PAGE 18
58 59 60 61 EN The printhead is designed to be inserted into any available slot. Once the printhead is inserted into a slot it sets up to work only with that combination of colors, so it is important to mark each printhead with the specific color combination to be used. Insert the printheads one by one. Push each printhead into the slot until it clicks into place. Pull the handle down to close the cover. Ensure that the end of the blue handle catches the wire loop on the near side of the carriage.
PAGE 19
64 63 62 65 10’ EN Close the top cover. The product checks and prepares the new printheads. Once the printhead check has finished the product will be ready to load paper for the printhead alignment. When the front panel prompts you to load paper for printhead alignment: Take the spindle and use it to load the paper the first time. Note: Calibration requires paper at least 20in (508mm) wide. Note: The spindle comes preinstalled in some models. If the blue removable stop is on the spindle, remove it.
PAGE 20
66 68 67 69 EN Add the removable stop to the spindle to keep the roll in place. Push the removable stop towards the roll as far as it will go. No gap should be left between stop and paper. From the front of the product, place the spindle into the product. Feed the leading edge of the paper into the product until the product takes hold of it. Do not insert the roll paper into the cutsheet slot. Note: do not close the roll cover until the front panel notifies you.
PAGE 21
71 70 72 73 2x EN The front panel will display a series of messages showing the progress of the printhead alignment. There is no need to take any action until the alignment has finished. HP DesignJet Z9+dr PostScript Printer only: The printer will calibrate the vertical cutters. HP DesignJet Z9+dr PostScript Printer only: Paper load on lower roll; Go to the rear of the product, and remove the orange stoppers from each end of the spindle.
PAGE 22
75 74 EN From the back of the product, place the spindle into the product. Feed the leading edge of the paper into the product until the product takes hold of it. Then move to the front of the product. Note: do not close the roll cover until the front panel notifies you. If the paper types of the two rolls differ, go to step 81 and calibrate the paper. FR Depuis l’arrière du produit, placez la bobine dans le produit.
PAGE 23
5 EN Connectivity and Mobile Printing ES FR Connectivité et impression mobile PT 1 - Vérifiez que l’imprimante est correctement connectée à Internet. 2 - Activez les services Web lors de la configuration initiale de l’imprimante, ou ultérieurement, en suivant les instructions qui s’affichent sur le panneau avant. Si le micrologiciel est mis à jour, le redémarrage de l’imprimante peut être nécessaire.
PAGE 24
76 77 78 hp.com/go/DesignJetclick EN The connectivity wizard will now start and take you step by step through connecting your printer to the internet. Follow the instructions. Take note of the printer’s email address for email printing. Install the product software on your computer. Download it from: www.hp.com/go/Z9/drivers Be sure to follow the software installation instructions.
PAGE 25
79 EN Print from your smartphone or tablet - AirPrint must be enabled on the printer. - iOS printing is enabled through Airprint, no installation is required. - For Android printing, install the HP Print Service Plugin from Google Play. - You can also download the HP Smart App (iOS/Android) to enhance your printing capabilities from a smartphone or tablet. For more information visit: http://www.hp.
PAGE 26
80 81 EN Optional: Managing printer security in HP Connected. When you enable web services the printer is in unlock mode meaning everyone who knows the printer’s email address can print. If you are the printer administrator you can change the status to lock mode, customize your printer’s email address, or manage the printer security (you will need the printer code and an account at HP Connected. Check your region’s availability).
PAGE 27
PAGE 28
EN © Copyright 2018 HP Development Company, L.P. ES The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. FR DE © Copyright 2018 HP Development Company, L.P.