HP Notebook User Guide
© Copyright 2010 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ..................................................................................................................... 3 Top .....................
5 Multimedia ..................................................................................................................................................... 18 Using the media activity action keys .................................................................................................. 18 Audio .................................................................................................................................................. 18 Adjusting the volume ..............................
Inserting a digital card ........................................................................................................ 34 Removing a digital card ..................................................................................................... 35 Using a USB device ........................................................................................................................... 35 Connecting a USB device ................................................................................
The computer is unusually warm ....................................................................................... 51 An external device is not working ...................................................................................... 51 The wireless network connection is not working ................................................................ 51 Contacting customer support ............................................................................................................. 52 Labels ...
1 Welcome ● Finding information After you set up and register the computer, take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, refer to Networking on page 10. ● Get to know your computer—Learn about your computer features. Refer to Getting to know your computer on page 3 and Keyboard and pointing devices on page 15 for additional information.
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about Quick Setup poster ● Setting up the computer ● Identifying computer components MeeGo Help ● Computer software To access the MeeGo Help, click the MeeGo Help icon in your Myzone Favorites, or click the Applications icon on the MeeGo panel.
2 Getting to know your computer ● Top ● Front ● Right side ● Left side ● Display ● Bottom Top TouchPad Component Description (1) TouchPad light Turns the TouchPad on and off. Quickly double-tap the TouchPad light to turn the TouchPad on and off. (2) Left TouchPad button Functions like the left button on an external mouse. (3) Right TouchPad button Functions like the right button on an external mouse. (4) TouchPad zone Moves the pointer and selects or activates items on the screen.
Lights Component (1) (2) (3) (4) 4 Description TouchPad light Caps lock light Mute light Wireless light Chapter 2 Getting to know your computer ● On: The TouchPad is off. ● Off: The TouchPad is on. ● On: Caps lock is on. ● Off: Caps lock is off. ● On: Computer sound is off. ● Off: Computer sound is on. ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Displays system information when pressed in combination with the esc key. (3) action keys Execute frequently used system functions.
Right side Component (1) (2) (3) Description Digital Media Slot Power light Power switch Supports the following digital card formats: ● Memory Stick ● Memory Stick Pro ● MultiMediaCard ● Secure Digital (SD) Card ● Secure Digital High Capacity (SDHC) Memory Card ● Secure Digital Extended Capacity (SDxC) Memory Card ● White: The computer is on. ● Blinking white: The computer is in the Sleep state. ● Off: The computer is off.
Left side Component Description (1) Power connector Connects an AC adapter. (2) Battery light ● Off: The computer is running on battery power. ● Blinking white: The battery has reached a low or critical battery level. ● Amber: A battery is charging. ● White: The computer is connected to external power and the battery is fully charged. (3) External monitor port Connects an external VGA monitor or projector. (4) Vent Enables airflow to cool internal components.
Display Component Description (1) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) Internal microphone Records sound. (3) Webcam Records video and captures still photographs. (4) Webcam light On: The webcam is in use. *The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions.
Bottom Component Description (1) Battery locking latch Locks the battery into the battery bay. (2) Battery bay Holds the battery. (3) Battery release latch Releases the battery from the battery bay.
3 Networking ● Using an Internet service provider (ISP) ● Identifying wireless and network status icons ● Creating a wireless connection ● Using a WLAN ● Using Bluetooth wireless devices (select models only) ● Connecting to a wired network Your computer may support one or both of the following types of Internet access: ● Wireless—For mobile Internet access, you can use a wireless connection. Refer to Connecting to a WLAN on page 12 or Setting up a new WLAN on page 12.
Network Connection (connected) Indicates that a wired network is connected and active. Network Connection (disconnected) Indicates that wired and wireless networks are not connected.
Using a WLAN A wireless connection connects the computer to Wi-Fi networks, or WLANs. A WLAN is composed of other computers and accessories that are linked by a wireless router or a wireless access point.
Protecting your WLAN When you set up a WLAN or access an existing WLAN, always enable security features to protect your network from unauthorized access. WLANs in public areas (hotspots) like coffee shops and airports may not provide any security. If you are concerned about the security of your computer in a hotspot, limit your network activities to e-mail that is not confidential and basic Internet surfing.
To connect the network cable: 1. Plug the network cable into the network jack (1) on the computer. 2. Plug the other end of the cable into a network wall jack (2). WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a modem or telephone cable into the RJ-45 (network) jack.
4 Keyboard and pointing devices ● Using the keyboard ● Using the TouchPad Using the keyboard Identifying the hotkey A hotkey is a combination of the fn key (1) and the esc key (2). Hotkey Description fn+esc Displays information about system hardware components and the system BIOS version number.
Identifying the action keys Action keys, located at the top of the keyboard, execute specifically assigned functions. Press a key to activate its assigned function. Action key Description f2 Decreases the screen brightness level. f3 Increases the screen brightness level. f4 Switches the screen image among display devices connected to the system.
Using the TouchPad To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go. Use the left and right TouchPad buttons like the buttons on an external mouse. NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased separately) by connecting it to one of the USB ports on the computer.
5 Multimedia ● Using the media activity action keys ● Audio ● Webcam ● Video Your computer may include the following: ● Integrated speakers ● Integrated microphones ● Integrated webcam ● Preinstalled multimedia software ● Multimedia buttons or keys Using the media activity action keys Media action keys allow you to play, pause, fast forward, or rewind a media file.
NOTE: Refer to Getting to know your computer on page 3 and Keyboard and pointing devices on page 15 for information on what type of volume controls your computer has. Checking your audio functions To check the system sound on your computer, follow these steps: 1. Select the Devices icon on the MeeGo panel. 2. Click All settings. 3. Click Sound. 4. On the Sound Effects tab, click on a sound under Choose an alert sound. To check the recording functions of the computer, follow these steps: 1.
▲ To connect a VGA display device, connect the device cable to the external monitor port. NOTE: Press f4 to switch the image between the display devices connected to the computer.
6 Power management ● Shutting down the computer ● Setting power options ● Using battery power ● Using external AC power Shutting down the computer CAUTION: Unsaved information will be lost when the computer is shut down.
NOTE: You cannot initiate any type of networking connection or perform any computer functions while the computer is in the Sleep state. Initiating and exiting Sleep The system is set at the factory to initiate Sleep after a period of inactivity when running on battery power or on external power. Power settings can be changed using the Devices icon on the MeeGo panel. With the computer on, you can initiate Sleep by closing the display. You can exit Sleep in either of the following ways: ● Open the display.
Displaying the remaining battery charge ▲ Place the mouse pointer over the battery meter icon on the MeeGo panel to see how much battery charge remains, or click the Devices icon on the MeeGo panel.
Inserting the battery To insert the battery: 1. Save your work and shut down the computer. 2. Disconnect all external devices connected to the computer. 3. Unplug the power cord from the AC outlet. 4. With the display closed, position the computer upside down on a flat surface with the battery bay toward you. 5. Insert the battery (1) into the battery bay until the battery release latch (2) clicks. 6. Slide the battery locking latch (3) to the right to lock the battery into the battery bay.
6. Slide and hold the battery release latch (2) while removing the battery (3) from the battery bay. Charging a battery WARNING! Do not charge the computer battery while you are onboard aircraft. The battery charges whenever the computer is plugged into external power through an AC adapter or an optional power adapter. The battery charges whether the computer is off or in use, but it charges faster when the computer is off.
Conserving and maximizing battery life To conserve battery life: ● Turn off wireless and local area network (LAN) connections and exit modem applications when you are not using them. ● Disconnect unused external devices that are not plugged into an external power source. ● Stop, disable, or remove any external media cards that you are not using. ● Decrease brightness. ● Initiate Sleep or shut down the computer when you are not using the computer. To maximize battery life: 1.
Resolving a low battery level Resolving a low battery level when external power is available ▲ Connect one of the following devices: ● AC adapter ● Optional docking or expansion device ● Optional power adapter purchased as an accessory from HP Resolving a low battery level when a charged battery is available 1. Save your work. 2. Turn off the computer or initiate Sleep. 3. Replace the discharged battery with a charged battery. 4. Turn on the computer.
Replacing the battery Computer battery life varies, depending on power management settings, programs running on the computer, display brightness, external devices connected to the computer, and other factors. NOTE: To ensure that you always have battery power when you need it, HP recommends purchasing a new battery when the storage capacity indicator on the battery turns green-yellow.
7 Drives ● Handling drives ● Replacing the hard drive Handling drives Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply. Observe these precautions: ● Before you move a computer that is connected to an external hard drive, initiate Sleep and allow the screen to clear, or properly disconnect the external hard drive.
Replacing the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on or in the Sleep state. If you are not sure whether the computer is off or in Sleep, turn the computer on by sliding the power switch. Then shut down the computer by sliding the power switch. Removing the hard drive 30 1. Save your work and shut down the computer. 2.
9. Grasp the tab on the hard drive, and lift the hard drive (3) out of the hard drive bay.
Installing a hard drive 1. Grasp the tab on the hard drive, and lower the hard drive into the hard drive bay (1). 2. Replace the 3 hard drive screws (2). 3. Insert the hard drive cable into the cable routing channel. 4. Grasp the tab on the hard drive cable connector (3), and then carefully press the hard drive cable connector onto the system board until it snaps into place. 5. Replace the vanity cover: 6. 32 a.
7. Reconnect external power and external devices. 8. Turn on the computer. 9. After you install the hard drive you will need to format the drive. Follow the on-screen instructions to format the hard drive.
8 External cards and devices ● Using Digital Media Slot cards ● Using a USB device ● Using optional external devices Using Digital Media Slot cards Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital media-equipped cameras and PDAs as well as with other computers. To determine which digital card formats are supported on your computer, refer to Getting to know your computer on page 3.
Removing a digital card CAUTION: To reduce the risk of loss of data or an unresponsive system, use the following procedure to safely remove the digital card. Save your information and close all programs associated with the digital card. To remove a digital card: 1. Select the Devices icon on the MeeGo panel. 2. Click the Eject button next to the name of the digital card. 3. Either press in on the card (1), and then remove it from the slot (2). – or – Pull the card out of the slot.
Connecting a USB device CAUTION: To prevent damage to a USB connector, use minimal force to connect a USB device. ▲ To connect a USB device to the computer, connect the USB cable for the device to the USB port. Removing a USB device CAUTION: To prevent damage to a USB connector, do not pull on the cable to remove the USB device. CAUTION: To prevent loss of information or an unresponsive system, use the following procedure to safely remove a USB device. To remove a USB device: 1.
Using optional external drives Removable external drives expand your options for storing and accessing information. A USB drive can be added by connecting the drive to a USB port on the computer. NOTE: HP external USB optical drives should be connected to the powered USB port on the computer.
9 Memory modules The computer memory module compartment is located on the bottom of the computer. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module. CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginning any procedure, ensure that you are discharged of static electricity by touching a grounded metal object.
6. Remove the existing memory module: a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up. b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. c. 7. To protect a memory module after removal, place it in an electrostatic-safe container.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 8. 9. Replace the vanity cover: a. Insert the 4 tabs on the front edge of the vanity cover into the 4 slots in the base (1). b. Rotate the back edge (2) of the vanity cover toward you, and then firmly press it down until it snaps into place.
10 Security ● Protecting the computer ● Using passwords ● Installing an optional security cable Protecting the computer NOTE: Security solutions are designed to act as deterrents, but they may not deter software attacks or prevent the computer from being mishandled or stolen. Security features provided with your computer can protect the computer, personal information, and data from a variety of risks. The way you use your computer will determine which security features you need to use.
Setting passwords in Setup Utility Setup Utility passwords Function Administrator password* ● Protects access to Setup Utility. ● After this password is set, it must be entered each time you access Setup Utility. CAUTION: If you forget your administrator password, you cannot access Setup Utility. NOTE: The administrator password can be used in place of the power-on password. NOTE: Your administrator password is not displayed as it is set, entered, changed, or deleted.
Entering an administrator password At the Enter password prompt, type your administrator password, and then press enter. After 3 unsuccessful attempts to enter the administrator password, you must restart the computer and try again. Managing a power-on password To set, change, or delete this password, follow these steps: 1. Open Setup Utility by turning on or restarting the computer. While the “Press the ESC key for Startup Menu” message is displayed in the lower-left corner of the screen, press esc.
44 3. Insert the cable lock into the security cable slot on the computer (3), and then lock the cable lock with the key. 4. Remove the key and keep it in a safe place.
11 Backup and recovery Recovery after a system failure is as good as your most recent backup. HP recommends that you regularly back up your files to ensure you have the latest data. Performing a system recovery CAUTION: Using Recovery completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed.
12 Setup Utility (BIOS) ● Starting Setup Utility ● Using Setup Utility ● Updating the BIOS Setup Utility, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Setup Utility includes settings for the types of peripherals installed, the startup sequence of the computer, and the amount of system and extended memory. CAUTION: Use extreme care when making changes in Setup Utility.
Displaying system information 1. Start Setup Utility. 2. Select the Main menu. System information such as the system time and date, and identification information about the computer is displayed. 3. To exit Setup Utility without changing any settings, use the arrow keys to select Exit > Exit Discarding Changes, and then press enter. Restoring factory default settings in Setup Utility 1. Start Setup Utility. 2. Use the arrow keys to select Exit > Load Setup Defaults, and then press enter. 3.
Updating the BIOS Updated versions of the BIOS may be available on the HP Web site. The computer will periodically check for updated versions of the BIOS when a network connection is available. You will be notified if an update is available. Follow the on-screen instructions to complete the update. NOTE: To set how often the BIOS updates are checked, click the Applications icon on the MeeGo panel. Click System Tools, and then click Update System. To manually install BIOS updates, follow these steps: 1.
Make a note of the path to the location on your hard drive where the BIOS update is downloaded. You will need to access this path when you are ready to install the update. NOTE: If you connect your computer to a network, consult the network administrator before installing any software updates, especially system BIOS updates. BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the download is complete.
A Troubleshooting and support ● Troubleshooting ● Contacting customer support ● Labels Troubleshooting The following sections describe several common issues and solutions.
The computer is on but not responding If the computer is turned on but is not responding to software or keyboard commands, try the following emergency shutdown procedures, in the sequence provided, until shutdown occurs: CAUTION: Emergency shutdown procedures result in the loss of unsaved information. ● Slide and hold the power switch for at least 5 seconds. ● Disconnect the computer from external power and remove the battery.
● Be sure that the wireless router or access point is properly connected to its power adapter and to the cable or DSL modem, and that the lights are on. ● Disconnect and then reconnect all cables, and turn the power off and then back on. Contacting customer support If the information provided in this guide does not address your questions, you can contact HP Customer Support at: http://www.hp.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support. The serial number label is affixed to the bottom of the computer.
B Routine care ● Cleaning the display ● Cleaning the TouchPad and keyboard Cleaning the display CAUTION: To prevent permanent damage to the computer, never spray water, cleaning fluids, or chemicals on the display. To remove smudges and lint, frequently clean the display with a soft damp, lint-free cloth. If the screen requires additional cleaning, use premoistened antistatic wipes or an antistatic screen cleaner.
C Specifications ● Input power ● Operating environment Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz.
D Electrostatic discharge Electrostatic discharge is the release of static electricity when two objects come into contact—for example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.
Index A action keys adjusting volume 16 audio CD or DVD controls 16 decrease screen brightness 16 identifying 5 increase screen brightness 16 media 18 muting speaker sound 16 switching screen image 16 volume 18 wireless 16 administrator password creating 42 entering 43 managing 42 airport security devices 29 audio features 18 audio functions, checking 19 audio-in (microphone) jack, identifying 7 audio-out (headphone) jack, identifying 7 B battery charging 25 conserving power 26 disposing 27 life 26 low batt
K keyboard hotkey, identifying keyboard, using 15 keys action 5 esc 5 fn 5 15 P passwords set in operating system 41 set in Setup Utility 42 ports external monitor 19 USB 6, 7, 35 VGA 19 power conserving 26 power connector, identifying 7 power light, identifying 6 power switch, identifying 6 power-on password creating 43 entering 43 managing 43 product name and number, computer 53 public WLAN connection 12 M managing a power-on password 43 managing an administrator password 42 media controls action keys
W webcam identifying 8 using 19 webcam light, identifying 8 wireless certification label 53 wireless devices, types 11 wireless encryption 13 wireless icon 10 wireless key identifying 16 using 11 wireless light 4, 11 wireless network (WLAN) connecting 12 corporate WLAN connection 12 described 11 equipment needed 12 public WLAN connection 12 security 13 WLAN antennas, identifying 8 WLAN device 53 WLAN label 53 writable media 21 Index 59
