HP EliteBook User Guide
© Copyright 2010 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel is a trademark of Intel Corporation in the U.S. and other countries. Java is a U.S. trademark of Sun Microsystems, Inc. Microsoft, Windows, and Windows Vista are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Features Identifying hardware ............................................................................................................................. 1 Top components .................................................................................................................. 1 Pointing devices .................................................................................................. 1 Lights ............................................................................
Bluetooth and Internet Connection Sharing (ICS) ............................................................. 24 Troubleshooting wireless network problems ...................................................................................... 25 Cannot create a WLAN connection ................................................................................... 25 Cannot connect to a preferred network .............................................................................
Adjusting the volume ......................................................................................................... 39 Multimedia software ........................................................................................................................... 40 Accessing your preinstalled multimedia software .............................................................. 41 Installing multimedia software from a disc .........................................................................
5 Power management Setting power options ......................................................................................................................... 61 Using power-saving states ................................................................................................. 61 Initiating and exiting Sleep ................................................................................ 61 Initiating and exiting Hibernation .......................................................................
6 Drives Identifying installed drives .................................................................................................................. 76 Handling drives ................................................................................................................................... 76 Improving hard drive performance ..................................................................................................... 78 Using Disk Defragmenter ...........................................
Security Protecting the computer ................................................................................................................... 109 Using passwords .............................................................................................................................. 110 Setting passwords in Windows ........................................................................................ 110 Setting passwords in Computer Setup ...................................................
Using Computer Setup ..................................................................................................................... 135 Navigating and selecting in Computer Setup ................................................................... 135 Restoring factory settings in Computer Setup ................................................................. 136 Computer Setup menus ...................................................................................................................
xii
1 Features Identifying hardware Components included with the computer may vary by region and model. The illustrations in this chapter identify the standard features on most computer models. To see a list of hardware installed in the computer: 1. Select Start > Computer > System Properties. 2. In the left pane, click Device Manager. You can also add hardware or modify device configurations using Device Manager.
Component Description (1) Pointing stick Moves the pointer and selects or activates items on the screen. (2) Left pointing stick button Functions like the left button on an external mouse. (3) TouchPad* Moves the pointer and selects or activates items on the screen. (4) Left TouchPad button* Functions like the left button on an external mouse. (5) Right pointing stick button Functions like the right button on an external mouse. (6) TouchPad scroll zone* Scrolls up or down.
Component Description (3) ● Amber: A battery is charging. ● Turquoise: A battery is close to full charge capacity. ● Blinking amber: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly. ● Off: If the computer is plugged into an external power source, the light turns off when all batteries in the computer are fully charged.
Buttons, switches, and fingerprint reader Component Description (1) ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button to shut down the computer. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component Description (4) ● When the computer is off, press the button to open HP QuickWeb. ● When the computer is on, press the button to open the default Web browser. (5) QuickWeb button Wireless button Turns the wireless feature on or off but does not establish a wireless connection. NOTE: A wireless network must be set up in order to establish a wireless connection. (6) TouchPad button Turns the TouchPad on or off. (7) Caps lock button Turns caps lock on or off.
Component Description (2) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (3) Windows logo key Displays the Windows Start menu. (4) Windows applications key Displays a shortcut menu for items beneath the pointer. (5) Embedded numeric keypad keys Can be used like the keys on an external numeric keypad. (6) Function keys Execute frequently used system functions when pressed in combination with the fn key.
Component Description (4) ● Blinking turquoise: The hard drive or optical drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. Drive light (5) Business card slot Holds a business card in position so that the webcam (select models only) can capture an image. (6) SD Card Reader Supports the Secure Digital (SD) Memory Card and MultiMediaCard (MMC) optional digital card formats. (7) Display release button Opens the computer. (8) Speakers (2) Produce sound.
Component Description (1) Smart card reader Supports optional smart cards and Java™ cards. (2) Upgrade bay Supports an optical drive or a hard drive. (3) eSATA/USB port Connects an eSATA device or a USB device. (4) RJ-45 (network) jack Connects a network cable. (5) RJ-11 (modem) jack (select models only) Connects a modem cable (purchased separately). Left-side components Component Description (1) Enables airflow to cool internal components.
Bottom components Component Description (1) Battery bay Holds the battery. (2) Battery release latch Releases the battery from the battery bay. (3) SIM slot (select models only) Contains a wireless subscriber identity module (SIM). The SIM slot is located inside the battery bay. (4) Docking connector Connects an optional docking device. (5) Accessory battery connector Connects an optional accessory battery. (6) Vents (7) Enable airflow to cool internal components.
Component Description (8) Business card holder Holds a business card. (9) Memory module compartment Contains the expansion memory module slot. (10) Hard drive bay Holds the hard drive. Display components Component Description (1) Turns off the display and initiates Sleep if the display is closed while the power is on. Internal display switch NOTE: The internal display switch is not visible from the outside of the computer. (2) Internal microphones (2) Record sound.
Wireless antennas (select models only) On select computer models, at least 2 antennas send and receive signals from one or more wireless devices. These antennas are not visible from the outside of the computer. Component Description (1) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide-area networks (WWANs). (2) WLAN antennas (3)* (select models only) Send and receive wireless signals to communicate with wireless local area networks (WLANs).
Additional hardware components Component Description (1) Power cord* Connects an AC adapter to an AC outlet. (2) AC adapter Converts AC power to DC power. (3) Battery* Powers the computer when the computer is not plugged into external power. *Batteries and power cords vary in appearance by country or region. Identifying the labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer.
Have this information available when you contact technical support. The service tag label is affixed to the bottom of the computer. ● Microsoft® Certificate of Authenticity—Contains the Windows Product Key. You may need the Product Key to update or troubleshoot the operating system. This certificate is affixed to the bottom of the computer. ● Regulatory label—Provides regulatory information about the computer. The regulatory label is affixed inside the battery bay.
2 Wireless, modem, and local area network Using wireless devices (select models only) Wireless technology transfers data across radio waves instead of wires.
Identifying wireless and network icons Icon Name Description Wireless (connected) Identifies the location of the wireless lights and the wireless buttons on the computer. Also identifies the Wireless Assistant software on the computer and indicates that one or more of the wireless devices are on. Wireless (disconnected) Indicates that all of the wireless devices are off.
Using Wireless Assistant software (select models only) A wireless device can be turned on or off using the Wireless Assistant software. If a wireless device is disabled by Computer Setup, it must be reenabled by Computer Setup before it can be turned on or off using Wireless Assistant. NOTE: Enabling or turning on a wireless device does not automatically connect the computer to a network or a Bluetooth-enabled device.
For more information, refer to Help and Support. Select Start > Help and Support.
Using a WLAN device (select models only) With a WLAN device, you can access a wireless local area network (WLAN), which is composed of other computers and accessories that are linked by a wireless router or a wireless access point. NOTE: The terms wireless router and wireless access point are often used interchangeably.
When you set up a WLAN or access an existing WLAN, always enable security features to protect your network from unauthorized access. The common security levels are Wi-Fi Protected Access (WPA) and Wired Equivalent Privacy (WEP). Because wireless radio signals travel outside the network, other WLAN devices can pick up unprotected signals and either connect to your network (uninvited) or capture information being sent across it.
Connecting to a WLAN To connect to the WLAN, follow these steps: 1. Be sure that the WLAN device is on. If it is on, the wireless light is blue. If the wireless light is amber, press the wireless button. 2. Select Start > Connect to. 3. Select your WLAN from the list, and then type the network security key, if required. ● If the network is unsecured, meaning that anyone can access the network, a warning is displayed. Click Connect Anyway to accept the warning and complete the connection.
Using HP Mobile Broadband (select models only) HP Mobile Broadband enables your computer to use wireless wide area networks (WWANs) to access the Internet from more places and over larger areas than it can by using WLANs. Using HP Mobile Broadband requires a network service provider (called a mobile network operator), which in most cases is a mobile phone network operator. Coverage for HP Mobile Broadband is similar to mobile phone voice coverage.
6. Remove the battery. 7. Insert the SIM into the SIM slot, and gently push the SIM into the slot until it is firmly seated. 8. Replace the battery. NOTE: HP Mobile Broadband will be disabled if the battery is not replaced. 9. Reconnect external power. 10. Reconnect external devices. 11. Turn on the computer. Removing a SIM (select models only) To remove a SIM: 22 1. Shut down the computer.
7. Press in on the SIM (1), and then remove it from the slot (2). 8. Replace the battery. 9. Reconnect external power. 10. Reconnect external devices. 11. Turn on the computer.
Using a Bluetooth wireless device (select models only) A Bluetooth device provides short-range wireless communications that replace the physical cable connections that traditionally link electronic devices such as the following: ● Computers (desktop, notebook, PDA) ● Phones (cellular, cordless, smart phone) ● Imaging devices (printer, camera) ● Audio devices (headset, speakers) Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network (PAN) of Bluetooth devi
Troubleshooting wireless network problems Some possible causes for wireless connection problems include the following: ● Wireless device is not installed correctly or has been disabled. ● Wireless device or router hardware has failed. ● Network configuration (SSID or security) has been changed. ● Wireless device encountered interference from other devices. NOTE: Wireless networking devices are included with select computer models only.
Cannot connect to a preferred network Windows can automatically repair a corrupted WLAN connection: ● If there is a network status icon in the notification area, at the far right of the taskbar, right-click the icon, and then click Diagnose and repair from the menu. Windows resets your network device and attempts to reconnect to one of the preferred networks. ● If an “x” is superimposed over the network status icon, one or more of your WLAN or LAN drivers are installed but the computer is not connected.
If you are provided with new wireless network keys and SSID for a network, and if you have previously connected to that network, follow these steps to connect to the network: 1. Select Start > Network > Network and Sharing Center > Manage wireless networks. A list showing the available WLANs is displayed. If you are in a hotspot where several WLANs are active, several will be displayed. 2. Right-click the network, and then click Properties.
Using the modem (select models only) The modem must be connected to an analog telephone line using a 6-pin, RJ-11 modem cable (purchased separately). In some countries or regions, a country- or region-specific modem cable adapter (purchased separately) is also required. Jacks for digital PBX systems may resemble analog telephone jacks, but they are not compatible with the modem. WARNING! Connecting the internal analog modem to a digital line can permanently damage the modem.
To connect the modem to an analog telephone line that does not have an RJ-11 telephone jack, follow these steps: 1. Plug the modem cable into the modem jack (1) on the computer. 2. Plug the modem cable into the country- or region-specific modem cable adapter (2). 3. Plug the country- or region-specific modem cable adapter (3) into the telephone wall jack. Selecting a location setting Viewing the current location selection To view the current location setting for the modem, follow these steps: 1.
CAUTION: To prevent configuring the modem in a way that violates the telecommunications regulations and laws of the country or region you are visiting, select the country or region in which the computer is located. The modem may not function properly if the correct country or region selection is not made. To add a location setting for the modem, follow these steps: 1. Select Start > Control Panel > Hardware and Sound > Phone and Modem Options. 2. Then click the Dialing Rules tab. 3. Click New.
To change the dialing mode in your current modem location setting, follow these steps: ● 1. Select Start > Control Panel > Hardware and Sound > Phone and Modem Options. 2. Then click the Dialing Rules tab. 3. Select your modem location setting. 4. Click Edit. 5. Click either Tone or Pulse. 6. Click OK twice. Check the telephone number you are dialing and the response of the remote modem. Dial a telephone number, be sure that there is a response from the remote modem, and then hang up.
Connecting to a local area network (LAN) Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased separately). If the network cable contains noise suppression circuitry (1), which prevents interference from TV and radio reception, orient the circuitry end of the cable (2) toward the computer. To connect the network cable: 1. Plug the network cable into the network jack (1) on the computer. 2. Plug the other end of the cable into a network wall jack (2).
3 Pointing devices and keyboard Using pointing devices Setting pointing device preferences Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options. To access Mouse Properties, select Start > Control Panel > Hardware and Sound > Mouse. Using the TouchPad To move the pointer, slide your finger across the TouchPad surface in the direction you want the pointer to go.
Function Hotkey Display system information. fn+esc Initiate Sleep. fn+f3 Switch the screen image. fn+f4 Display battery information. fn+f8 Decrease screen brightness. fn+f9 Increase screen brightness. fn+f10 Activate the ambient light sensor. fn+f11 To use a hotkey command on the computer keyboard, follow either of these steps: ● Briefly press the fn key, and then briefly press the second key of the hotkey command.
When Sleep is initiated, your information is stored in system memory, the screen is cleared, and power is conserved. While the computer is in the Sleep state, the power lights blink. The computer must be on before you can initiate Sleep. NOTE: If a critical battery level occurs while the computer is in the Sleep state, the computer initiates Hibernation and the information stored in memory is saved to the hard drive.
Using HP QuickLook QuickLook allows you to save calendar, contact, inbox, and task information from Microsoft Outlook to the hard drive of your computer. Then, when the computer is off or in Hibernation, you can press the QuickLook button on the computer to view this information without waiting for the operating system to restart. Use QuickLook to manage contact information, calendar events, e-mail information, and tasks without restarting your computer.
Component Description NOTE: The keypad function that is active when the computer is turned off will be reinstated when the computer is turned back on. Using the embedded numeric keypad The 15 keys of the embedded numeric keypad can be used like the keys on an external keypad. When the embedded numeric keypad is turned on, each key on the keypad performs the function indicated by the icon in the upper-right corner of the key.
Cleaning the TouchPad, keyboard, and vents Dirt and grease on the TouchPad can cause the pointer to jump around on the screen. To avoid this, clean the TouchPad with a damp cloth, and wash your hands frequently when using the computer. WARNING! To reduce the risk of electric shock or damage to internal components, do not use a vacuum cleaner attachment to clean the keyboard. A vacuum cleaner can deposit household debris on the keyboard surface.
4 Multimedia Multimedia features Your computer includes multimedia features that allow you to listen to music and view pictures.
◦ ● To increase volume, press the volume up button (3). Windows volume control: a. Click the Volume icon in the notification area, at the far right of the taskbar. b. Increase or decrease the volume by moving the slider up or down. Click the Mute icon to mute the volume. – or – a. Right-click the Volume icon in the notification area, at the far right of the taskbar, and then click Open Volume Mixer. b.
Accessing your preinstalled multimedia software To access preinstalled multimedia software: ▲ Select Start > All Programs, and then open the multimedia program you want to use. NOTE: Some programs may be located in subfolders. NOTE: For details about using software included with the computer, refer to the software manufacturer’s instructions. These instructions may be provided with the software, on disc, or on the manufacturer’s Web site.
Audio Your computer enables you to use a variety of audio features: ● Play music using your computer speakers and/or connected external speakers ● Record sound using the internal microphones or connect an external microphone ● Download music from the Internet ● Create multimedia presentations using audio and images ● Transmit sound and images with instant messaging programs ● Stream radio programs (select models only) or receive FM radio signals ● Create or “burn” audio CDs Connecting external
NOTE: For best results when recording, speak directly into the microphone and record sound in a setting free of background noise. ▲ To confirm or change the audio settings on your computer, right-click the Sound icon on the taskbar, or select Start> Control Panel > Audio.
Video Your computer enables you to use a variety of video features: ● Watch movies ● Play games over the Internet ● Edit pictures and video to create presentations ● Connect external video devices Connecting an external monitor or projector Your computer has both an external monitor port and a DisplayPort that allow you to connect external monitors and projectors.
▲ To connect a digital display device, connect the device cable to the DisplayPort. NOTE: If a properly connected external display device does not display an image, press fn+f4 to transfer the image to the device. Repeatedly pressing fn+f4 alternates the screen image between the computer display and the device.
Optical drive (select models only) Your computer may include an optical drive that expands the functionality of the computer. The optical drive allows you to read data discs, play music, and watch movies. Identifying the optical drive ▲ Select Start > Computer. You will see a list of all the devices installed on your computer.
CAUTION: To prevent possible audio and video degradation, loss of information, or loss of audio or video playback functionality, do not initiate Sleep or Hibernation while reading a CD, DVD, or BD, or writing to a CD or DVD. Selecting the right disc (CDs, DVDs, and BDs) An optical drive supports optical discs (CDs, DVDs, and BDs). CDs, used to store digital data, are also used for commercial audio recordings and are convenient for your personal storage needs.
LightScribe DVD+R discs Use LightScribe DVD+R discs for sharing and storing data, home videos, and photos. These discs are read-compatible with most DVD-ROM drives and DVD video players. With a LightScribe-enabled drive and LightScribe software, you can write data to the disc and then add a designer label to the outside of the disc. Blu-ray Discs (BDs) BD is a high-density optical disc format for the storage of digital information, including high-definition video.
5. Gently press the disc (3) down onto the tray spindle until the disc snaps into place. 6. Close the disc tray. If you have not yet configured AutoPlay, as described in the following section, an AutoPlay dialog box opens. It prompts you to select how you want to use the media content. NOTE: For best results, be sure that your AC adapter is plugged into an external power source while playing a BD. Configuring AutoPlay 1. Select Start > Control Panel > Play CDs or other media automatically. 2.
To change settings through the operating system: 1. Select Start > Computer > System properties. 2. In the left pane, click Device Manager. NOTE: Windows includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information. 3. Click the plus (+) next to DVD/CD-ROM drives. 4.
Creating (burning) a CD or DVD If your optical drive is a CD-RW, DVD-RW, or DVD±RW optical drive, you can use software such as Windows Media Player to burn data and audio files, including MP3 and WAV music files. To burn video files to a CD or DVD, use MyDVD. Observe the following guidelines when burning a CD or DVD: ● Before burning a disc, save and close any open files and close all programs.
2. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces. NOTE: If the tray is not fully accessible, tilt the disc carefully as you remove it. 3. Close the disc tray and place the disc in a protective case. Troubleshooting The following sections describe several common issues and resolutions. The optical disc tray does not open for removal of a CD, DVD, or BD 52 1.
3. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces. NOTE: If the tray is not fully accessible, tilt the disc carefully as you remove it. 4. Close the disc tray and place the disc in a protective case. The computer does not detect the optical drive If Windows does not detect an attached device, the device driver software may be missing or corrupted.
A disc does not play ● Save your work and close all open programs before playing a CD, DVD, or BD. ● Log off the Internet before playing a CD, DVD, or BD. ● Be sure that you insert the disc properly. ● Be sure that the disc is clean. If necessary, clean the disc with filtered water and a lint-free cloth. Wipe from the center of the disc to the outer edge. ● Check the disc for scratches. If you find scratches, treat the disc with an optical disc repair kit available at many electronics stores.
A movie stops, skips, or plays erratically ● Clean the disc. ● Conserve system resources by trying the following suggestions: ◦ Log off the Internet. ◦ Change the color properties of the desktop: 1. Right-click on a blank area of the computer desktop, and select Personalize > Display Settings. 2. Set Colors to Medium (16 bit), if this setting is not already selected. ◦ Disconnect external devices, such as a printer, scanner, camera, or handheld device.
A device driver must be reinstalled 1. Remove any discs from the optical drive. 2. Click Start and type device manager in the Start Search box. As you type, search results are listed in the pane above the box. 3. In the results pane, click Device Manager. If prompted by User Account Control, click Continue. 4.
To use Microsoft Update: 1. Open your Internet browser and go to http://www.microsoft.com, and click Security & Updates. 2. Click Microsoft Update to get the latest updates for your computer operating system, programs, and hardware. 3. Follow the on-screen instructions to install Microsoft Update. If prompted by User Account Control, click Continue. 4. Click Change settings and select a time for Microsoft Update to check for updates to the Windows operating system and other Microsoft products. 5.
Webcam (select models only) Your computer may include an integrated webcam, located at the top of the display. With the preinstalled software, you can use the webcam to record audio and video and capture still photographs. You can preview the photo, video recording, or audio recording, and save it on your computer hard drive. To access the webcam and HP Webcam software, select Start > All Programs > HP > HP Webcam.
● Hue—Controls the aspect of color that distinguishes it from another color (what makes a color red, green, or blue). Hue is distinct from saturation, which measures the intensity of the hue. ● Saturation—Controls the strength of color in the final image. A higher saturation setting creates a bolder image; a lower saturation setting creates a more subtle image. ● Sharpness—Controls the definition of edges in an image.
4. Slowly lower the display (1) until the webcam light (2) blinks and you hear a sound, which indicates that the webcam is now in focus. The webcam turns on, and the scanning process starts immediately. You will hear a camera shutter sound when the image is captured, and the information from the card is filled in the fields automatically. 5. If you are capturing multiple business card images, remove the business card and insert another one. The webcam light turns on when the card is in focus.
5 Power management Setting power options Using power-saving states The computer has two power-saving states enabled at the factory: Sleep and Hibernation. When Sleep is initiated, the power light blinks and the screen clears. Your work is saved to memory, letting you exit Sleep faster than exiting Hibernation. If the computer is in the Sleep state for an extended period or if the battery reaches a critical battery level while in the Sleep state, the computer initiates Hibernation.
When the computer exits Sleep, the power lights turn on and your work returns to the screen where you stopped working. NOTE: If you have set a password to be required when the computer exits Sleep, you must enter your Windows password before your work will return to the screen.
You can change power plan settings or create your own power plan. Viewing the current power plan ▲ Move the pointer over the battery meter icon in the notification area, at the far right of the taskbar. – or – Select Start > Control Panel > System and Maintenance > Power Options. Selecting a different power plan ▲ Click the battery meter icon in the notification area, and then select a power plan from the list.
Using Power Assistant (select models only) Power Assistant allows you to configure system settings to optimize your computer's power consumption and battery charge.
When you disconnect external AC power, the following events occur: ● The computer switches to battery power. ● The display brightness is automatically decreased to save battery life. To increase display brightness, press the fn+f10 hotkey or reconnect the AC adapter. Connecting the AC adapter WARNING! To reduce the risk of electric shock or damage to the equipment: Plug the power cord into an AC outlet that is easily accessible at all times.
You can keep a battery in the computer or in storage, depending on how you work. Keeping the battery in the computer whenever the computer is plugged into AC power charges the battery and also protects your work in case of a power outage. However, a battery in the computer slowly discharges when the computer is off and unplugged from external power.
The time shown indicates the approximate running time remaining on the battery if the battery continues to provide power at the current level. For example, the time remaining will decrease when a DVD is playing and will increase when a DVD stops playing. Inserting or removing the battery CAUTION: Removing a battery that is the sole power source can cause loss of information.
3. Remove the battery from the computer (2). Charging a battery WARNING! Do not charge the computer battery while you are onboard aircraft. The battery charges whenever the computer is plugged into external power through an AC adapter, an optional power adapter, or an optional docking device. The battery charges whether the computer is off or in use, but it charges faster when the computer is off.
● Blinking amber: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly. ● Off: If the computer is plugged into an external power source, the light turns off when all batteries in the computer are fully charged. If the computer is not plugged into an external power source, the light stays off until the battery reaches a low battery level.
Resolving a low battery level when a charged battery is available 1. Turn off the computer or initiate Hibernation. 2. Remove the discharged battery, and then insert a charged battery. 3. Turn on the computer. Resolving a low battery level when no power source is available ▲ Initiate Hibernation. – or – Save your work and shut down the computer. Resolving a low battery level when the computer cannot exit Hibernation When the computer lacks sufficient power to exit Hibernation, follow these steps: 1.
Step 2: Disable Hibernation and Sleep 1. Click the battery meter icon in the notification area, and then click More power options. – or – Select Start > Control Panel > System and Maintenance > Power Options. 2. Under the current power plan, click Change plan settings. 3. Record the Turn off the display and Put the computer to sleep settings listed in the On battery column so that you can reset them after the calibration. 4.
Step 4: Fully recharge the battery To recharge the battery: 1. Plug the computer into external power and maintain external power until the battery is fully recharged. When the battery is recharged, the battery light on the computer turns off. You can use the computer while the battery is recharging, but the battery will charge faster if the computer is off. 2. If the computer is off, turn it on when the battery is fully charged and the battery light has turned off.
If a computer will be unused and unplugged from external power for more than 2 weeks, remove the battery and store it separately. To prolong the charge of a stored battery, place it in a cool, dry place. NOTE: A stored battery should be checked every 6 months. If the capacity is less than 50 percent, recharge the battery before returning it to storage. Calibrate a battery before using it if it has been stored for one month or more.
Testing an AC adapter Test the AC adapter if the computer exhibits any of the following symptoms: ● The computer will not turn on when connected to the AC adapter. ● The display does not turn on when the computer is connected to the AC adapter and external power. ● The power light is off when the computer is connected to the AC adapter. To test the AC adapter: 1. Remove the battery from the computer. 2. Connect the AC adapter to the computer and to an AC outlet. 3. Turn on the computer.
If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try the following emergency procedures in the sequence provided: ● Press ctrl+alt+delete, and then press the power button. ● Press and hold the power button for at least 5 seconds. ● Disconnect the computer from external power and remove the battery.
6 Drives Identifying installed drives Your computer includes a hard drive (with a rotating disc) or a solid-state drive (SSD) with solid-state memory. Because it has no moving parts, an SSD does not generate as much heat as a hard drive. To view the drives installed on the computer, select Start > Computer. NOTE: Windows includes the User Account Control feature to improve the security of your computer.
CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information, observe these precautions: Before you move a computer that is connected to an external hard drive, initiate Sleep and allow the screen to clear, or properly disconnect the external hard drive. Before handling a drive, discharge static electricity by touching the unpainted metal surface of the drive. Do not touch the connector pins on a removable drive or on the computer.
Improving hard drive performance Using Disk Defragmenter As you use the computer, files on the hard drive become fragmented. Disk Defragmenter consolidates the fragmented files and folders on the hard drive so that the system can run more efficiently. After you start Disk Defragmenter, it works without supervision. Depending on the size of your hard drive and the number of fragmented files, Disk Defragmenter may take more than an hour to complete.
Using HP 3D DriveGuard HP 3D DriveGuard protects the hard drive by parking the drive and halting I/O requests under either of the following conditions: ● You drop the computer. ● You move the computer with the display closed while the computer is running on battery power. A short time after the end of one of these events, HP 3D DriveGuard returns the hard drive to normal operation. NOTE: Solid-state drives lack rotating parts, so protection by HP 3D DriveGuard is unnecessary.
Using HP 3D DriveGuard software The HP 3D DriveGuard software enables you to perform the following tasks: ● Enable and disable HP 3D DriveGuard. NOTE: Permission to enable or disable HP 3D DriveGuard is dependent on certain user privileges. Members of an Administrator group can change privileges for non-Administrator users. ● Determine whether a drive in the system is supported. To open the software and change settings, follow these steps: 1.
Replacing a hard drive in the hard drive bay CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by briefly pressing the power button. Then shut down the computer through the operating system. To remove a hard drive: 1. Save your work.
11. Lift the hard drive (3) out of the hard drive bay. To install a hard drive: 82 1. Insert the hard drive into the hard drive bay (1). 2. Pull the hard drive tab (2) to the left to connect the hard drive. 3. Tighten the hard drive screw (3). 4. Align the tabs (1) on the hard drive cover with the notches on the computer. 5. Replace the cover (2).
6. Tighten the hard drive cover screws (3). 7. Replace the battery. 8. Turn the computer right-side up, and then reconnect external power and external devices. 9. Turn on the computer.
Replacing a drive in the upgrade bay The upgrade bay can hold either a hard drive or an optical drive. Removing the protective insert The upgrade bay may contain a protective insert. You must remove the insert before inserting a drive into the upgrade bay. To remove the insert: 1. Save your work. 2. Shut down the computer and close the display. 3. Disconnect all external hardware devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5.
To remove a hard drive from the upgrade bay: 1. Save your work. 2. Shut down the computer and close the display. 3. Disconnect all external hardware devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5. Turn the computer upside down on a flat surface. 6. Remove the battery from the computer. 7. Remove the protective screw caps (1), and then remove the 4 hard drive screws (2). 8. Loosen the upgrade bay screw (1). 9.
10. Remove the hard drive from the upgrade bay. To install a hard drive in the upgrade bay: 1. 86 Insert the hard drive into the upgrade bay.
2. Tighten the upgrade bay screw. 3. Replace the 4 hard drive screws (1), and then replace the protective screw caps (2). 4. Replace the battery. 5. Turn the computer right-side up, and then reconnect external power and external devices. 6. Turn on the computer. Replacing an optical drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the optical drive from the upgrade bay.
To remove an optical drive from the upgrade bay: 88 1. Save your work. 2. Shut down the computer and close the display. 3. Disconnect all external hardware devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5. Turn the computer upside down on a flat surface. 6. Remove the battery from the computer. 7. Loosen the upgrade bay screw (1). 8. Using a flat-bladed screwdriver, gently push the tab to release the optical drive (2). 9.
To install an optical drive in the upgrade bay: 1. Insert the optical drive into the upgrade bay. 2. Tighten the upgrade bay screw. 3. Replace the battery. 4. Turn the computer right-side up, and then reconnect external power and external devices. 5. Turn on the computer.
7 External devices Using a USB device Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Some USB devices may require additional support software, which is usually included with the device. For more information about device-specific software, refer to the manufacturer's instructions. Your computer model has 4 USB ports, which support USB 1.0, USB 1.1, and USB 2.0 devices.
Stopping and removing a USB device CAUTION: To prevent loss of information or an unresponsive system, stop a USB device before removing it. CAUTION: To prevent damage to a USB connector, do not pull on the cable to remove the USB device. To stop and remove a USB device: 1. Double-click the Safely Remove Hardware icon in the notification area, at the far right of the taskbar. NOTE: To display the Safely Remove Hardware icon, click the Show Hidden Icons icon (< or <<) in the notification area. 2.
Using a 1394 device IEEE 1394 is a hardware interface that connects a high-speed multimedia or data storage device to the computer. Scanners, digital cameras, and digital camcorders often require a 1394 connection. Some 1394 devices may require additional support software, which is usually included with the device. For more information about device-specific software, refer to the manufacturer's instructions. The 1394 port also supports IEEE 1394a devices.
3. Click Stop, and then click OK. 4. Remove the device.
Using external drives Removable external drives expand your options for storing and accessing information. A USB drive can be added by connecting the drive to a USB port on the computer. USB drives include the following types: ● 1.
Using a docking device The docking connector connects the computer to an optional docking device. An optional docking device provides additional ports and connectors that can be used with the computer.
8 External media cards Using SD Card Reader cards Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other computers. The SD Card Reader supports the following formats: ● MultiMediaCard (MMC) ● Secure Digital (SD) Memory Card Inserting a digital card CAUTION: To avoid damaging the digital card or the computer, do not insert any type of adapter into the SD Card Reader.
Removing a digital card CAUTION: To prevent loss of information or an unresponsive system, stop a digital card before removing it. 1. Save your information and close all programs associated with the digital card. NOTE: To stop a data transfer, click Cancel in the operating system Copying window. 2. Stop the digital card: a. Double-click the Safely Remove Hardware icon in the notification area, at the far right of the taskbar.
CAUTION: To prevent damage to the connectors: Use minimal force when inserting an ExpressCard. Do not move or transport the computer when an ExpressCard is in use. The ExpressCard slot may contain a protective insert. To remove the insert: 1. Press in on the insert (1) to unlock it. 2. Pull the insert out of the slot (2). To insert an ExpressCard: 1. Hold the card label-side up, with the connectors facing the computer. 2.
Stopping and removing an ExpressCard CAUTION: To prevent loss of data or an unresponsive system, stop an ExpressCard before removing it. 1. Save your information and close all programs associated with the ExpressCard. NOTE: To stop a data transfer, click Cancel in the operating system Copying window. 2. Stop the ExpressCard: a. Double-click the Safely Remove Hardware icon in the notification area, at the far right of the taskbar.
Inserting a smart card To insert a smart card: 1. Holding the smart card label-side up, gently slide the card into the smart card reader until the card is seated. 2. Follow the on-screen instructions for logging on to the computer using the smart card PIN. Removing a smart card To remove a smart card: ▲ Grasp the edge of the smart card, and pull it out of the smart card reader.
9 Memory modules The computer has two memory module compartments. The primary memory module compartment is located under the keyboard. The expansion memory module compartment is located on the bottom of the computer. The memory capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot.
Adding or replacing a memory module in the expansion memory module slot To add or replace a memory module in the expansion memory module slot, follow these steps: 1. Save your work. 2. Shut down the computer and close the display. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. 3. Disconnect all external devices connected to the computer. 4.
b. Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot. To protect a memory module after removal, place it in an electrostatic-safe container. 10. Insert a memory module: a. Align the notched edge (1) of the memory module with the tab in the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module and do not bend the memory module. b.
13. Tighten the memory module compartment cover screw (3). 14. Replace the battery. 15. Turn the computer right-side up, and then reconnect external power and external devices. 16. Turn on the computer.
Upgrading a memory module in the primary memory module slot To upgrade a memory module in the primary memory module slot, follow these steps: 1. Save your work. 2. Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. 3. Disconnect all external devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5.
9. Slide the 4 keyboard release latches to release the keyboard. 10. Gently lift the top edge of the keyboard and tilt the keyboard over until it rests on the palm rest of the computer. 11. Remove the memory module: a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module.
b. Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot. To protect a memory module after removal, place it in an electrostatic-safe container. 12. Insert a memory module: a. Align the notched edge (1) of the memory module with the tab in the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module and do not bend the memory module. b.
14. Slide the 4 keyboard release latches to lock the keyboard (2). 15. Close the cover. 16. Turn the computer upside down on a flat surface. 17. Replace the 3 keyboard access screws. 18. Replace the battery. 19. Turn the computer right-side up, and then reconnect external power and external devices. 20. Turn on the computer.
10 Security Protecting the computer NOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. NOTE: In some countries or regions, the computer supports CompuTrace, which is an online securitybased tracking and recovery service. If the computer is stolen, CompuTrace can track the computer if the unauthorized user accesses the Internet. You must purchase the software and subscribe to the service in order to use CompuTrace.
Using passwords Most security features use passwords. Whenever you set a password, write down the password and store it in a secure location away from the computer. Note the following password considerations: ● Setup and DriveLock passwords are set in Computer Setup and are managed by the system BIOS.
BIOS administrator passwords Function DriveLock user password Protects access to the internal hard drive that is protected by DriveLock, and is set under DriveLock Passwords during the enable process. TPM embedded security password When enabled as a BIOS administrator password, protects access to the computer contents when the computer turns on, restarts, or exits Hibernation. This password requires the optional embedded security chip to support this security feature.
Your changes go into effect when the computer restarts. To delete this password in Computer Setup, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3. Use a pointing device or the arrow keys to select Security > Change Password, and then press enter. 4. When prompted, type your current password. 5.
● The user password and the master password can be identical. ● You can delete a user password or master password only by removing DriveLock protection from the drive. DriveLock protection can be removed from the drive only with the master password. Setting a DriveLock password To set a DriveLock password in Computer Setup, follow these steps: 1. Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2.
Changing a DriveLock password To change a DriveLock password in Computer Setup, follow these steps: 1. Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3. Use a pointing device or the arrow keys to select Security > DriveLock passwords, and then press enter. 4. Use a pointing device to select an internal hard drive.
Using Computer Setup Auto DriveLock In a multiple-user environment, you can set an Automatic DriveLock password. When the Automatic DriveLock password is enabled, a random user password and a DriveLock master password will be created for you. When any user passes the password credential, the same random user and DriveLock master password will be used to unlock the drive. NOTE: You must have a BIOS administrator password before you can access the Automatic DriveLock features.
Using Computer Setup security features Securing system devices You can disable or enable system devices from the following menus in Computer Setup: ● Boot Options ● Device Configurations ● Built-In Device Options ● Port Options To disable or reenable system devices in Computer Setup, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3.
To view this general system information in Computer Setup, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3. Use a pointing device or the arrow keys to select File > System Information, and then press enter. NOTE: To prevent unauthorized access to this information, you must create a BIOS administrator password in Computer Setup.
Using antivirus software When you use the computer to access e-mail, a network, or the Internet, you expose the computer to computer viruses. Computer viruses can disable the operating system, programs, or utilities, or cause them to function abnormally. Antivirus software can detect most viruses, destroy them, and in most cases, repair any damage they have caused. To provide ongoing protection against newly discovered viruses, antivirus software must be kept up to date.
Using firewall software When you use the computer to access e-mail, a network, or the Internet, unauthorized persons may be able to gain access to the computer, your personal files, and information about you. Use the firewall software preinstalled on the computer to protect your privacy. McAfee Total Protection antivirus software is preinstalled on the computer. To access your software, select Start > All Programs > McAfee > Managed Services > Total Protection.
Installing critical updates CAUTION: Microsoft sends alerts regarding critical updates. To protect the computer from security breaches and computer viruses, install all critical updates from Microsoft as soon as you receive an alert. Updates to the operating system and other software may have become available after the computer was shipped.
Using HP ProtectTools Security Manager (select models only) HP ProtectTools Security Manager software is preinstalled on select computer models. This software can be accessed through Windows Control Panel. It provides security features that help protect against unauthorized access to the computer, networks, and critical data. For more information, refer to the HP ProtectTools Security Manager software Help. Select Start > HP > HP ProtectTools Security Manager.
Installing a security cable NOTE: A security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. 1. Loop the security cable around a secured object. 2. Insert the key (1) into the cable lock (2). 3. Insert the cable lock into the security cable slot on the computer (3), and then lock the cable lock with the key. NOTE: Your computer may look different from the illustration. The location of the security cable slot varies by computer model.
11 Software updates 123
Updating software Updated versions of the software provided with your computer are available either through the HP Support Assistant or on the HP Web site. The HP Support Assistant automatically checks for updates from HP. The utility runs at a specified interval and provides a list of support alerts, such as security enhancements, and optional software and driver updates.
To update the software using the HP Web site, follow these steps: 1. Identify your computer model, product category, and series or family. Prepare for a system BIOS update by identifying the BIOS version currently installed on the computer. For details, refer to the "Determining the BIOS version" section. If your computer is connected to a network, consult the network administrator before installing any software updates, especially system BIOS updates.
Updating the BIOS To update the BIOS, first determine what BIOS version you currently have, and then download and install the new BIOS. Determining the BIOS version BIOS version information (also known as ROM date and System BIOS) can be displayed by pressing fn+esc (if you are already in Windows) or by using Computer Setup. To use Computer Setup for displaying BIOS information, follow these steps: 1.
5. Follow the on-screen instructions to access the BIOS update you want to download. Make a note of the download date, name, or other identifier. You may need this information to locate the update later, after it has been downloaded to your hard drive. 6. At the download area, perform these steps: a. Identify the BIOS update that is newer than the BIOS version currently installed on your computer. b. Follow the on-screen instructions to download your selection to the hard drive.
Updating programs and drivers 1. Open your Web browser, go to http://www.hp.com/support, and then select your country or region. 2. Click the option for software and driver downloads, type your computer model number in the product box, and then press enter. – or – If you want a specific SoftPaq, type the SoftPaq number in the Search box, at the top-right corner of the screen. Then press enter, and follow the instructions provided. Proceed to step 6. 3.
Using SoftPaq Download Manager HP SoftPaq Download Manager (SDM) provides quick access to SoftPaq information for HP computers, without the need to specify a SoftPaq number. The software works by reading and downloading a published database file containing computer model and SoftPaq information. Using this tool, you can easily search for SoftPaqs by computer model, and then download, unpack, and install the SoftPaqs.
12 Backup and recovery To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
Backing up your information Recovery after a system failure is as complete as your most current backup. You should create your initial backup immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. You can back up your information to an optional external hard drive, a network drive, or discs.
Performing a recovery In case of system failure or instability, the computer provides the following tools to recover your files: ● Windows recovery tools: You can use the Backup and Restore Center to recover information you have previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows from starting correctly. ● f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image.
Using f11 recovery tools CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled. Personal files must be restored from a backup.
5. Click Next. 6. Select Repair your computer. 7. Follow the on-screen instructions.
13 Computer Setup Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer. NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy support is enabled. To start Computer Setup, follow these steps: 1.
To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the tab key and the arrow keys to select File > Ignore changes and exit, and then press enter. – or – ● To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions.
File menu Select To do this System Information ● View identification information for the computer and the batteries in the system. ● View specification information for the processor, cache and memory size, system ROM, video revision, and keyboard controller version. Set System Date and Time Set or change the date and time on the computer. System Diagnostics Displays the following information: ● System Information ◦ Identification information for the computer and the batteries in the system.
Select To do this Setup BIOS Administrator Password Set up a BIOS administrator password. User Management (requires a BIOS administrator password) Create New BIOS User Account ● Select from a list of BIOS users. ● Select from a list of ProtectTools users. Password Policy (requires a BIOS administrator password) Revise password policy criteria. HP SpareKey Enable/disable HP SpareKey (enabled by default).
Select To do this Language Change the Computer Setup language. Boot Options ● Set a Startup Menu delay (in seconds). ● Set the Multiboot Express Boot Popup delay in seconds. ● Enable/disable Custom Logo (disabled by default). ● Enable/disable Display Diagnostic URL (enabled by default). ● Enable/disable CD-ROM boot (enabled by default). ● Enable/disable SD Card boot (enabled by default). ● Enable/disable floppy boot (enabled by default).
Select Built-In Device Options 140 Chapter 13 Computer Setup To do this ● Enable/disable Preboot Authentication on HP QuickLook Boot (enabled by default). ● Enable/disable HP QuickWeb (enabled by default). ● Enable/disable HP QuickWeb: Write Protect (disabled by default). ● Enable/disable Virtualization Technology (select models only; disabled by default). ● Enable/disable TXT (Intel Trusted Execution Technology) (select models only; disabled by default).
Select Port Options (all are enabled by default) To do this ● Enable/disable the microphone (enabled by default). ● Enable/disable the internal speakers (enabled by default). NOTE: All port options are enabled by default. ● Enable/disable the serial port. ● Enable/disable the parallel port. ● Enable/disable the flash media reader. ● Enable/disable the USB port. CAUTION: Disabling the USB port also disables MultiBay devices and ExpressCard devices on the advanced port replicator.
14 MultiBoot About the boot device order As the computer starts, the system attempts to boot from enabled boot devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly.
Enabling boot devices in Computer Setup The computer will boot to a USB device or a NIC device only if the device has first been enabled in Computer Setup. To start Computer Setup and enable a USB device or a NIC device as a boot device, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3.
Considering boot order changes Before changing the boot order, note the following considerations: ● When the computer restarts after the boot order has been changed, the computer attempts to start using the new boot order. ● If there is more than one type of boot device, the computer attempts to boot using the first of each type of boot device (except for optical devices).
Choosing MultiBoot preferences You can use MultiBoot in the following ways: ● To set a new boot order that the computer uses each time it is turned on, by changing the boot order in Computer Setup. ● To dynamically choose the boot device, by pressing esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen, and then pressing f9 to enter the Boot Device Options menu. ● To use MultiBoot Express to set variable boot orders.
Dynamically choosing a boot device To dynamically choose a boot device for the current startup sequence, follow these steps: 1. Open the Select Boot Device menu by turning on or restarting the computer, and then pressing esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f9. 3. Use a pointing device or the arrow keys to select a boot device, and then press enter. Your changes go into effect immediately.
15 Management and Printing Using Client Management Solutions Client Management Solutions software provides standards-based solutions for managing client (user) desktop, workstation, notebook, and tablet computers in a networked environment.
Managing and updating software HP provides several tools for managing and updating software on client computers: ● HP Client Automation (select models only) ● HP SSM (System Software Manager) HP Client Automation (select models only) HP Client Automation automates the management of software such as operating systems, programs, software updates, and content and configuration settings to ensure that each computer is maintained in the correct configuration.
Index Symbols/Numerics 1394 cable, connecting 92 1394 devices connecting 92 removing 92 1394 port 92 1394 port, identifying 8 A AC adapter connecting 65 identifying 12 accessory battery connector, identifying 9 administrator password 110 airport security devices 77 ambient light sensor hotkey 35 AMT options AMT Setup Prompt (CtrlP) 141 Firmware Progress Event Support 141 Firmware Verbosity 141 Initiate Intel CIRA 141 Terminal Emulation Mode 141 Unconfigure AMT on next boot 141 USB Key Provisioning Support
power 4 QuickLook 4 QuickWeb 5 TouchPad 2, 5 volume mute 5 wireless 5 C cables 1394 92 modem 28 USB 90 calibrating battery 70 caps lock button, identifying 5 caps lock light, identifying 3 CD copying 50 playing 48 removing 51, 52 CD drive 94 Certificate of Authenticity label 13 changing boot order 145 charging batteries 68, 70 checking audio functions 42 compartments Bluetooth 7 expansion memory module 10 components additional hardware 12 bottom 9 display 10 front 6 left-side 8 rear 7 right-side 7 top 1 com
function keys 33 function keys, identifying 6 H hard drive external 94 HP 3D DriveGuard 79 installing 82 hard drive bay, identifying 10 hard drive recovery 133 hardware, identifying 1 headphone (audio-out) jack 8 Hibernation exiting 62 initiated during critical battery level 69 initiating 62 hotkeys ambient light sensor 35 battery charge information 35 decreasing screen brightness 35 description 33 displaying system information 34 increasing screen brightness 35 initiating Sleep 34 switching screen image 35
modem cable connecting 28 country- or region-specific cable adapter 28 noise suppression circuitry 28 modem software setting/adding location 29 travel connection problems 30 monitor port, external 7 monitor, connecting 44 mouse, external connecting 33 setting preferences 33 Multi Core CPU 140 MultiBoot Express 142, 146 multimedia software, installing 41 MultiMediaCard 96 mute button, identifying 5 mute light, identifying 3 N network key 26 network security codes network key 26 SSID 26 Network Service Boot 1
set up BIOS administrator password 138 System IDs 138 security, wireless 18 serial number, computer 12 service tag 12 set security level 141 setup of WLAN 18 setup utility File menu 137 navigating and selecting 135 restoring factory settings 136 Security menu 137 System Configuration menu 138 setup, computer 1 shut down 74 SIM inserting 21 removing 22 SIM label 13 SIM slot, identifying 9 Sleep exiting 61 initiating 61 Sleep hotkey 34 slots business card 7 memory 101 memory module 10 SIM 9, 21 smart card rea
wireless light 6, 15 wireless light, identifying 2 wireless network (WLAN) connecting 20 corporate WLAN connection 20 equipment needed 18 functional range 20 public WLAN connection 20 security 18 wireless network problems, troubleshooting 25 WLAN device 13, 14, 18 WLAN label 13 WLAN module compartment, identifying 9 writable media 61 WWAN device 14 WWAN module compartment, identifying 9 154 Index
