HP OfficeJet Pro 7730 Wide Format All-inOne series User Guide
Copyright information HP Company notices Acknowledgements © 2020 HP Development Company, L.P. The information contained in this document is subject to change without notice. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All rights reserved. Reproduction, adaptation, or translation of this material is prohibited without prior written permission of HP, except as allowed under copyright laws.
Safety information Always follow basic safety precautions when using this product to reduce risk of injury from fire or electric shock. - Read and understand all instructions in the documentation that comes with the printer. - Observe all warnings and instructions marked on the product. - Unplug this product from wall outlets before cleaning. - Do not install or use this product near water, or when you are wet. - Install the product securely on a stable surface.
Table of contents 1 How do I? ...................................................................................................................................................... 1 2 Get started .................................................................................................................................................... 2 Accessibility ......................................................................................................................................................
Print on special and custom-size paper .............................................................................................................. 35 Print on both sides (duplexing) ........................................................................................................................... 37 Print using the HP Smart app .............................................................................................................................. 38 Print with mobile devices ...............
Block unwanted fax numbers ........................................................................................................... 59 Set up phone book contacts ................................................................................................................................ 60 Create and edit a phone book contact .............................................................................................. 60 Create and edit a group phone book contact .....................................
Shared voice/fax line with computer dial-up modem and answering machine ........................................................................................................ 84 Shared voice/fax line with computer DSL/ADSL modem and answering machine ........................................................................................................ 86 Case K: Shared voice/fax line with computer dial-up modem and voice mail ............... 87 Test fax setup ............................................
Open the embedded web server ..................................................................................................... 108 Embedded web server cannot be opened ...................................................................................... 109 10 Solve a problem ....................................................................................................................................... 110 Jams and paper-feed issues ...............................................................
Wireless test report ......................................................................................................................... 137 Web access test report .................................................................................................................... 137 Solve problems using Web Services .................................................................................................................. 137 Maintain the printer ...............................................
Restriction on hazardous substances statement (Turkey) ............................................................ 154 EPEAT ............................................................................................................................................... 154 SEPA Ecolabel User Information (China) ......................................................................................... 154 China Energy Label for Printer, Fax and Copier ..........................................................
xii ENWW
1 ENWW How do I? ● Get started ● Print ● Copy and scan ● Fax ● Web Services ● Work with cartridges ● Network setup ● Printer management tools ● Solve a problem 1
2 Get started This guide provides details about how to use the printer and how to resolve problems.
HP EcoSolutions (HP and the Environment) HP is committed to helping you optimize your environmental footprint and empowering you to print responsibly—at home or in the office. For more detailed information about environmental guidelines that HP follows during the manufacturing process, see Environmental product stewardship program. For more information about HP's environmental initiatives, visit www.hp.com/ecosolutions.
3. You can touch Schecule On/Off to get to the time settings after setting one of these to ON. 4. Touch the desired option, and follow the onscreen messages to set the day and time to turn the printer off and on. CAUTION: Always turn the printer off properly, using either Schedule Off or (the Power button) located on the front left side of the printer.
To turn Quiet Mode on or off from the printer software (Windows) 1. Open the HP printer software. For more information, see Open the HP printer software (Windows). 2. Click Quiet Mode . 3. Select On or Off . 4. Click Save Setting. To turn Quiet Mode on or off from the printer software (OS X and macOS) 1. Open HP Utility. NOTE: HP Utility is located in the HP folder in the Applications folder. 2. Select the printer. 3. Click Quiet Mode . 4. Select On or Off . 5. Click Apply Now.
Top and front view 1 Document feeder 2 Document feeder paper-width guides 3 Document feeder tray 4 Scanner lid 5 Scanner glass 6 Cartridge access door 7 Output tray 8 Output tray extension 9 Input tray / Tray 1 10 Input tray / Tray2 11 Power button 12 Control panel display Printing supplies area 1 6 Printhead Chapter 2 Get started ENWW
2 Cartridges 3 Cartridge access door NOTE: Cartridges should be kept in the printer to prevent possible print quality issues or printhead damage. Avoid removing supplies for extended periods of time. Do not turn the printer off when a cartridge is missing.
NOTE: Return the control panel to its original position by pushing down the left side until it is back in place. Overview of buttons and lights The following diagram and related table provide a quick reference to the printer control panel features. 8 Label Name and Description 1 Home button: Returns to the home screen from any other screen. 2 Control panel display: Touch the screen to select menu options, or scroll through the menu items.
Control panel display icons Icon Purpose Copy: Opens the Copy menu where you can select a copy type or change the copy settings. Scan: Opens the Scan menu where you can select a destination for your scan. Apps: Access the apps from your printer. Fax: Displays a screen where you can send a fax, or change fax settings. Setup: Displays the setup screen for changing preferences, network setup, Wi-Fi Direct, Web Services setup, fax setup, and other maintenance settings and generating reports.
Icon Purpose HP EcoSolutions: Displays a screen where you can configure some of the printer's environmental features. Help: Opens the Help menu where you can view How To videos, printer feature information, and tips. Change printer settings Use the control panel to change the printer functions and settings, print reports, or get help for the printer. TIP: If the printer is connected to a computer, you can also change the printer settings using the printer management tools in the software.
Paper basics The printer is designed to work well with most types of office paper. It is best to test a variety of print paper types before buying large quantities. Use HP paper for optimum print quality. Visit the HP website at www.hp.com for more information about HP paper. HP recommends plain papers with the ColorLok logo for printing everyday documents.
Business documents ● HP Premium Presentation Paper 120g Matte or HP Professional Paper 120 Matte These paper are heavy two-sided matte paper perfect for presentation, proposals, reports, and newsletters. They are heavyweight for an impressive look and feel. ● HP Brochure Paper Glossy or HP Professional Paper Glossy These papers are glossy-coated on both sides for two-sided use.
● Do not overload the tray or document feeder.
To change tray settings NOTE: You can also change the tray settings from the HP printer software or EWS. To access EWS and the printer software, see Embedded web server and Open the HP printer software (Windows). 1. Make sure the printer is turned on. 2. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, and then touch (Setup). 3. Scroll and touch Tray and Paper Management. 4.
2. ENWW Slide the paper guides towards the edges of the tray as far as possible. ● To slide the paper-width guides, press the button on the left paper-width guide and slide the guide at the same time. ● To slide the paper-length guide, press the button on the paper-length guide and slide the guide at the same time.
3. Insert the paper in portrait orientation and with the side to be printed facing down. Make sure the stack of paper is aligned with the appropriate paper size lines on the front of the tray. Also, make sure the stack of paper does not exceed the stack height marking on the right edge of the tray. NOTE: Tray 2 can only be loaded with plain paper of standard sizes between A4 or Letter and A3 or Tabloid. Do not load paper while the printer is printing.
4. Adjust the paper-width guides and the paper-length guide until they touch the edge of the stack of paper. NOTE: Before inserting the input tray, check the gap in the printer where the input tray was and remove any paper. 5. Reinsert the input tray into the printer. 6. Pull out the output tray extension as shown. To load B-size paper 1. ENWW Pull out the input tray completely with both hands.
NOTE: If there is other paper in the input tray, remove the paper before loading a different paper type or size. 18 2. Press the button near the front right of the tray, and pull out the input tray extension. 3. Slide the paper guides towards the edges of the tray as far as possible. ● To slide the paper-width guides, press the button on the left paper-width guide and slide the guide at the same time.
4. Insert the paper in portrait orientation and with the side to be printed facing down. Make sure the stack of paper is aligned with the appropriate paper size lines on the front of the tray. Also, make sure the stack of paper does not exceed the stack height marking on the left edge of the tray. NOTE: Do not load paper while the printer is printing.
5. Adjust the paper-width guides and the paper-length guide until they touch the edge of the stack of paper. NOTE: Before inserting the input tray, check the gap in the printer where the input tray was and remove any paper. 6. Reinsert the input tray into the printer. NOTE: When you insert the input tray, the input tray extension remains outside of the printer. This is the expected result.
7. Pull out the output tray extension as shown. Pull out the output tray extension further to fully extend the tray. To load an envelope 1. Pull out the input tray completely with both hands. NOTE: If there is other paper in the input tray, remove the paper before loading a different paper type or size. 2. ENWW Slide the paper guides towards the edges of the tray as far as possible.
3. Insert the envelope in portrait orientation and with the side to be printed facing down. Make sure the stack of envelope is aligned with the appropriate paper size lines on the front of the tray. Also, make sure the stack of envelope does not exceed the stack height marking on the right edge of the tray. NOTE: Do not load paper while the printer is printing.
4. Adjust the paper-width guides and the paper-length guide until they touch the edge of the stack of paper. NOTE: Before inserting the input tray, check the gap in the printer where the input tray was and remove any paper. 5. Reinsert the input tray into the printer. 6. Pull out the output tray extension as shown. To load cards and photo paper 1. ENWW Pull out the input tray completely with both hands.
NOTE: If there is other paper in the input tray, remove the paper before loading a different paper type or size. 2. 24 Slide the paper guides towards the edges of the tray as far as possible. ● To slide the paper-width guides, press the button on the left paper-width guide and slide the guide at the same time. ● To slide the paper-length guide, press the button on the paper-length guide and slide the guide at the same time.
3. Insert the cards or photo paper in portrait orientation and with the side to be printed facing down. Make sure the stack of card or photo is aligned with the appropriate paper size lines on the front of the tray. Also, make sure the stack of card or photo does not exceed the stack height marking on the right edge of the tray. NOTE: Do not load paper while the printer is printing.
4. Adjust the paper-width guides and the paper-length guide until they touch the edge of the stack of paper. NOTE: Before inserting the input tray, check the gap in the printer where the input tray was and remove any paper. 26 5. Reinsert the input tray into the printer. 6. Pull out the output tray extension as shown.
Load an original on the scanner glass You can copy, scan, or fax originals by loading them on the scanner glass. NOTE: Many of the special features do not work correctly if the scanner glass and lid backing are not clean. For more information, see Maintain the printer. NOTE: Remove all originals from the document feeder tray before lifting the lid on the printer. To load an original on the scanner glass 1. Lift the scanner lid. 2.
To load an original in the document feeder 1. Load your original print-side up into the document feeder. a. If you are loading an original printed in portrait orientation, place the pages so that the top edge of the document goes in first. If you are loading an original printed in landscape orientation, place the pages so that the left edge of the document goes in first. b.
To update the printer using the embedded web server 1. Open the EWS. For more information, see Embedded web server. 2. Click the Tools tab. 3. In the Printer Updates section, click Firmware Updates, and then follow the onscreen instructions. NOTE: If a printer update is available, the printer downloads and installs the update, and then restarts. NOTE: If prompted for proxy settings and if your network uses proxy settings, follow the onscreen instructions to set up a proxy server.
Get more information about the HP Smart app For basic instructions on how to print, scan, and troubleshoot using HP Smart, see Print using the HP Smart app, Scan using HP Smart and Get help from the HP Smart app . For more information about using HP Smart for printing, scanning, accessing printer features, and troubleshooting issues, go to: ● iOS/Android: www.hp.com/go/hpsmart-help ● Windows: www.hp.com/go/hpsmartwin-help Turn the printer off Press (the Power button) to turn off the printer.
3 Print Most print settings are automatically handled by the software application. Change the settings manually only when you want to change print quality, print on specific types of paper, or use special features. TIP: This printer includes HP ePrint , a free service from HP that allows you to print documents on your HP ePrint-enabled printer anytime, from any location, without any additional software or printer drivers. For more information, see HP ePrint .
7. Click OK to close the Properties dialog box. 8. Click Print or OK to begin printing. To print documents (OS X and macOS) 1. From the File menu in your software, choose Print. 2. Make sure your printer is selected. 3. Set the print options. If you do not see options on the Print dialog, click Show Details. ● Choose the appropriate paper size in the Paper Size pop-up menu. NOTE: If you change the paper size, ensure that you have loaded the correct paper. 4. ● Select the orientation.
a. Choose the appropriate paper size in the Paper Size pop-up menu. NOTE: If you change the paper size, ensure that you have loaded the correct paper. b. 4. From the pop-up menu, choose Paper Type/Quality, and then choose the option that provides the best quality or maximum dpi. Click Print.
NOTE: If you change the paper size, ensure that you have loaded the correct paper. 4. From the pop-up menu, choose Paper Type/Quality, and verify the paper type setting is set to Plain Paper. 5. Click Print. Print photos You can print a photo from a computer. Do not leave unused photo paper in the input tray. The paper might start to curl, which could impair the quality of your printout. Photo paper should be flat before printing.
4. 5. From the pop-up menu, choose Paper Type/Quality, and then choose the following settings: ● Paper Type: The appropriate photo paper type ● Quality: Select the option that provides the best quality or maximum dpi. ● Click the Color Options disclosure triangle, and then choose the appropriate Photo Fix option. – Off: applies no changes to the image. – On: automatically focuses the image; moderately adjusts image sharpness. Select any other print settings you want, and then click Print.
2. ● From the File menu in your software application, click Page Setup, and then make sure the printer you want to use is selected in the Format For pop-up menu. ● From the File menu in your software application, click Print, and then make sure the printer you want to use is selected. Select Manage Custom Sizes in the Paper Size pop-up menu. NOTE: If you do not see these options in the Print dialog, click the disclosure triangle next to the Printer pop-up menu or click Show Details. 3.
3. d. Click +, and then select the new item in the list and type a name for the custom paper size. e. Enter the height and width for your custom paper. f. Click Done or OK, and then click Save. Use the created custom paper size to print. a. From the File menu in your software application, click Print. b. Make sure your printer is selected. c. Choose the custom paper size name you created in the Paper Size pop-up menu. d. Select any other print settings you want, and then click Print.
Print using the HP Smart app This section provides basic instructions for using the HP Smart app to print from your Android, iOS, or Windows 10 device. For more information about using the HP Smart app, go to: ● iOS/Android: www.hp.com/go/hpsmart-help ● Windows: www.hp.com/go/hpsmartwin-help To print from a Windows 10 device 1. Load paper in the input tray. For more information, see Load paper. 2. Open HP Smart.
NOTE: Devices running iOS 4.2 or later have AirPrint preinstalled. ● Android: Download the HP Print Service Plugin (supported by most Android devices) from the Google Play Store and enable it on your device. NOTE: Devices running Android 4.4 or later are supported by the HP Print Service Plugin. Devices running Android 4.3 or earlier can print using the HP ePrint app, available in the Google Play Store. ● Windows Mobile: Tap Print from the Device menu.
NOTE: Ink level warnings and indicators provide estimates for planning purposes only. When an indicator shows low ink levels, consider having a replacement cartridge available to avoid possible printing delays. You do not need to replace cartridges until you are prompted to. ● Always turn off the printer with (the Power button) to allow the printer to protect the nozzles. Paper loading tips For more information, also see Load paper.
● – Color: Uses ink from all cartridges for full color prints. – Black & White or Black Ink Only: Uses the black ink only for normal or lower quality black and white prints. – High Quality Grayscale: Uses ink from both the color and black cartridges to produce a wider range of black and grey tones for high quality black and white prints. To understand print quality settings: The print quality is measured in print resolution dots per inch (dpi).
4 Copy and scan ● Copy ● Scan ● Tips for copy and scan success Copy To copy document or ID card 1. Make sure you have paper loaded in the input tray. For more information, see Load paper. 2. Place your original print-side down on the scanner glass or print-side up in the document feeder. 3. From the printer control panel display, touch Copy . 4. Select Document or ID Card . 5. Enter the number of copies by using the keypad or make changes to other settings.
● Change scan settings (Windows) Scan to a computer Before scanning to a computer, make sure you have already installed the HP recommended printer software. The printer and computer must be connected and turned on. In addition, on Windows computers, the printer software must be running prior to scanning. You can use the HP printer software to scan documents into editable text. For more information, see Scanning documents as editable text.
● Choose Save as PDF to save the document (or photo) as a PDF file. ● Choose Save as JPEG to save the photo (or document) as an image file. NOTE: The initial screen allows you to review and modify basic settings. Click the More link at the top right corner of the Scan dialog box to review and modify detailed settings. For more information, see Change scan settings (Windows). If Show Viewer After Scan is selected, you can make adjustments to the scanned image in the preview screen.
12. Touch Scan to Email. 13. Touch OK when the scan completes, and then touch Yes to send another email, or No to finish. Scan a document or photo to email You can scan to email from either the control panel or HP printer software. To scan a document or photo to email from the control panel 1. Load your original print-side down on the scanner glass or print-side up in the document feeder. 2. From Home screen, touch Apps, and then touch Scan-to-Email app. 3.
● Auto-login ● Store Email ● Remove from list ● Change PIN ● Delete Account Scan using HP Smart You can use the HP Smart app to scan documents or photos from the printer's scanner, and you can also scan using your device camera. HP Smart includes editing tools that allow you to adjust the scanned image before saving or sharing. You can print, save your scans locally or in cloud storage, and share them via email, SMS, Facebook, Instagram, etc.
To scan a document or photo using the device camera If your device has a camera, you can use the HP Smart app to scan a printed document or photo with the device camera. You can then use HP Smart to edit, save, print or share the image. 1. Open HP Smart. For more information, see Use the HP Smart app to print, scan, and troubleshoot from an iOS, Android, or Windows 10 device. 2. Select Scan, and then select Camera. 3.
Scan using Webscan Webscan is a feature of the embedded web server that lets you scan photos and documents from your printer to your computer using a web browser. This feature is available even if you did not install the printer software on your computer. For more information, see Embedded web server. NOTE: By default, Webscan is off. You can enable this feature from the EWS. If you are unable to open Webscan in the EWS, your network administrator might have turned it off.
1. Load your original print-side down on the scanner glass or print-side up in the document feeder. 2. Open the HP printer software. For more information, see Open the HP printer software (Windows). 3. In the printer software, click Scan a Document or Photo . 4. Select Save as Editable Text (OCR) and click Scan . NOTE: The initial screen allows you to review and modify basic settings. Click the More link at the top right corner of the Scan dialog box to review and modify detailed settings.
● – The text on the original is faint or wrinkled. – The text is too small. – The structure of the document is too complex. – The text is tightly spaced. For example, if the text that the software converts has missing or combined characters, "rn" might appear as "m." – The text is on a colored background. Colored backgrounds can cause images in the foreground to blend too much. Choose the correct profile. Be sure to select a shortcut or preset that allows scanning as editable text.
1. Load your original print-side down on the scanner glass or print-side up in the document feeder. 2. Open the HP printer software. For more information, see Open the HP printer software (Windows). 3. In the printer software, click Scan a Document or Photo . 4. Click the More link in the top right corner of the HP Scan dialog box. The detailed settings pane appears on the right. The left column summarizes the current settings for each section.
5 Fax You can use the printer to send and receive faxes, including color faxes. You can schedule faxes to be sent at a later time within 24 hours and set up phone book contacts to send faxes quickly and easily to frequently used numbers. From the printer control panel, you can also set a number of fax options, such as resolution and the contrast between lightness and darkness on the faxes you send. NOTE: Before you begin faxing, make sure you have set up the printer correctly for faxing.
To send a standard fax from the printer control panel 1. Load your original print-side down on the scanner glass or print-side up in the document feeder. 2. From the printer control panel display, touch Fax . 3. Touch Send Now. 4. Enter the fax number by using the keypad or by selecting from the phone book. TIP: To add a pause in the fax number you are entering, touch * repeatedly, until a dash (-) appears on the display. 5. Touch TIP: Send .
Send a fax from a phone You can send a fax using your telephone extension. This allows you to talk with the intended recipient before sending the fax. To send a fax from an extension phone 1. Load your original print-side down on the scanner glass or print-side up in the document feeder. 2. Dial the number by using the keypad on the phone that is connected to the printer.
TIP: If you are using a calling card to send a fax and you have your calling card PIN stored as a phone book contact, when prompted to enter your PIN, touch ( Phone Book ), and then touch Local Phone Book to select the phone book contact where you have your PIN stored. Your fax is sent when the receiving fax machine answers. Send a fax using printer memory You can scan a black-and-white fax into memory and then send the fax from memory.
6. Touch the name of the group that you want to send. 7. Touch Send Fax . Printer sends the document to all the numbers in the selected group. TIP: If the recipient reports issues with the quality of the fax, try changing the resolution or contrast of your fax. Send a fax in Error Correction Mode Error Correction Mode (ECM) prevents loss of data due to poor phone lines by detecting errors that occur during transmission and automatically requesting retransmission of the erroneous portion.
Receive a fax manually When you are on the phone, the person you are speaking with can send you a fax while you are still connected. You can pick up the handset to talk or listen for fax tones. You can receive faxes manually from a phone that is directly connected to the printer (on the 2-EXT port). To receive a fax manually 1. Make sure the printer is turned on and you have paper loaded in the main tray. 2. Remove any originals from the document feeder tray. 3.
Reprint received faxes from memory The received faxes that are not printed are stored in memory. NOTE: After the memory becomes full, the printer cannot receive the new fax until you print or delete the faxes from memory. You might also want to delete the faxes in memory for security or privacy purposes. You can reprint up to 30 of the most recently printed faxes, if they are still in memory. For example, you might need to reprint your faxes if you lost the copy of your last printout.
Set automatic reduction for incoming faxes The Automatic Reduction setting determines what the printer does if it receives a fax that is too large for the loaded paper size. This setting is turned on by default, so the image of the incoming fax is reduced to fit on one page, if possible. If this feature is turned off, information that does not fit on the first page is printed on a second page.
3. Touch Preferences . 4. Touch Junk Fax Blocking . 5. Touch the number you want to remove, and then touch Remove. To print a junk fax list 1. From the printer control panel display, touch Fax . 2. Touch Setup , and then touch Reports . 3. Touch Print Fax Reports . 4. Touch Junk Fax Report. 5. Touch Print to begin printing. Set up phone book contacts You can set up frequently used fax numbers as phone book contacts. This lets you quickly dial those numbers using the printer control panel.
4. Touch Name and then edit the name of the Phone Book contact, and then touch Done . 5. Touch Fax Number and edit the fax number for the phone book contact, and then touch Done . NOTE: Be sure to include any pauses or other required numbers, such as an area code, an access code for numbers outside a PBX system (usually a 9 or 0), or a long-distance prefix. 6. Touch Done . Create and edit a group phone book contact You can store groups of fax numbers as group phone book contacts.
4. Touch Delete. 5. Touch Yes to confirm. To delete group phone book contacts 1. From the printer control panel display, touch Fax . 2. Touch Phone Book , then touch 3. Touch the name of the phone book contact you want to delete. 4. Touch Delete. 5. Touch Yes to confirm. and select ( Group ) to switch to the group phone book.
● Turn on the Auto Answer setting if you want the printer to answer faxes automatically. The printer answers all incoming calls and faxes. ● Turn off the Auto Answer setting if you want to receive faxes manually. You must be available to respond in person to the incoming fax call or else the printer does not receive faxes. To set the answer mode 1. From the printer control panel display, touch Fax . 2. Touch Setup , and then touch Preferences . 3. Touch Auto Answer to turn it on or off.
To change the answer ring pattern for distinctive ring 1. Ensure that the printer is set to answer fax calls automatically. For more information, see Set the answer mode (Auto answer). 2. From the printer control panel display, touch Fax . 3. Touch Setup , and then select Preferences . 4. Touch Distinctive Ring . 5. Touch one ring pattern and then follow the on-screen instruction.
Set the fax speed You can set the fax speed used to communicate between your printer and other fax machines when sending and receiving faxes. If you use one of the following, setting the fax speed to a slower speed might be required: ● An Internet phone service ● A PBX (private branch exchange) system ● Fax on Voice over Internet Protocol (VoIP) ● An integrated services digital network (ISDN) service If you experience problems sending and receiving faxes, try using a slower Speed .
● ISDN: An integrated services digital network (ISDN) system. ● VoIP: A low-cost phone service that allows you to send and receive faxes with your printer by using the Internet. This method is called Fax on Voice over Internet Protocol (VoIP). For more information, see Fax on Voice over Internet Protocol. HP printers are designed specifically for use with traditional analog phone services.
● Print fax confirmation reports ● Print fax error reports ● Print and view the fax log ● Clear the fax log ● Print the details of the last fax transaction ● Print a Caller ID Report ● View the Call History Print fax confirmation reports You can print a confirmation report either when a fax is sent, or when any fax is sent or received. The default setting is On (Fax Send). When turned off, a confirmation message appears briefly on the control panel after each fax is sent or received.
3. Touch Reports and touch Fax Error Reports. 4. Touch to select one of the following. On (Fax Send) Prints whenever a transmission error occurs. This is the default setting. On (Fax Receive) Prints whenever a receiving error occurs. On (Fax Send and Fax Receive) Prints whenever a fax error occurs. Off Does not print any fax error reports. Print and view the fax log You can print a log of faxes that have been received and sent by the printer. To print the fax log from the printer control panel 1.
To print a Caller ID History Report 1. From the printer control panel display, touch Fax . 2. Touch Setup , and then touch Reports . 3. Touch Print Fax Reports . 4. Touch Caller ID Report. 5. Touch Print to begin printing. View the Call History You can view a list of all the calls placed from the printer. NOTE: You cannot print the call history. To view the call history 1. From the printer control panel display, touch Fax . 2. Touch Send Now. 3. Touch ( Phone Book ). 4.
NOTE: You might need to connect the phone cord to your country/region adapter. ● If your country/region is listed in the table, you probably have a parallel-type telephone system. In a parallel-type phone system, you are able to connect shared telephone equipment to the phone line by using the "2-EXT" port on the back of the printer. NOTE: If you have a parallel-type phone system, HP recommends you connect a 2-wire phone cord to the telephone wall jack.
equipment directly to the printer, and you might also need to change some fax settings before you can fax successfully. 1. Determine if your telephone system is serial or parallel. For more information, see Set up faxing (parallel phone systems). 2. 3. a. Serial-type telephone system. b. Parallel-type telephone system—Go to step 2. Select the combination of equipment and services sharing your fax line. ● DSL: A Digital subscriber line (DSL) service through your telephone company.
Other equipment or services sharing your fax line DSL PBX Distinctive ring service Voice calls Computer dialup modem Recommended fax setup Answering machine Voice mail service Case C: Set up the printer with a PBX phone system or an ISDN line Case D: Fax with a distinctive ring service on the same line Case E: Shared voice/fax line Case F: Shared voice/fax line with voice mail Case G: Fax line shared with computer modem (no voice calls received) Case H: Shared voice/fax line with computer modem Case I
To set up the printer with a separate fax line 1. Connect one end of the phone cord to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the printer. NOTE: You might need to connect the phone cord to your country/region adapter. 2. Turn on the Auto Answer setting. 3. (Optional) Change the Rings to Answer setting to the lowest setting (two rings). 4. Run a fax test.
To set up the printer with DSL 1. Obtain a DSL filter from your DSL provider. 2. Connect one end of the phone cord to the DSL filter, and then connect the other end to the port labeled 1-LINE on the back of the printer. NOTE: You might need to connect the phone cord to your country/region adapter. If you do not use the supplied cord to connect from the DSL filter to the printer, you might not be able to fax successfully.
Figure 5-3 Back view of the printer 1 Telephone wall jack. 2 Connect the phone cord to the port labelled 1-LINE on the back of the printer. You might need to connect the phone cord to your country/region adapter. To set up the printer with a distinctive ring service 1. Connect one end of the phone cord to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the printer. NOTE: You might need to connect the phone cord to your country/region adapter. 2.
Figure 5-4 Back view of the printer 1 Telephone wall jack. 2 Connect the phone cord to the port labelled 1-LINE on the back of the printer. You might need to connect the phone cord to your country/region adapter. 3 Telephone (optional). To set up the printer with a shared voice/fax line 1. Connect one end of the phone cord to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the printer.
Case F: Shared voice/fax line with voice mail If you receive both voice calls and fax calls at the same phone number, and you also subscribe to a voice mail service through your telephone company, set up the printer as described in this section. NOTE: You cannot receive faxes automatically if you have a voice mail service at the same phone number you use for fax calls. You must receive faxes manually; this means you must be available to respond in person to incoming fax calls.
● Set up the printer with a computer DSL/ADSL modem Set up the printer with a computer dial-up modem If you are using the same phone line for sending faxes and for a computer dial-up modem, follow these directions for setting up the printer. Figure 5-6 Back view of the printer 1 Telephone wall jack. 2 Connect the phone cord to the port labelled 1-LINE on the back of the printer. You might need to connect the phone cord to your country/region adapter. 3 Computer with modem.
If you encounter problems setting up the printer with optional equipment, contact your local service provider or vendor for further assistance. Set up the printer with a computer DSL/ADSL modem If you have a DSL line and use that phone line to send faxes, follow these instructions to set up your fax. 1 Telephone wall jack. 2 Parallel splitter. 3 DSL/ADSL filter. Connect one end of the phone cord to the 1-LINE port on the back of the printer. Connect the other end of the cord to the DSL/ADSL filter.
5. Connect the parallel splitter to the wall jack. 6. Run a fax test. When the phone rings, the printer automatically answers after the number of rings you set in the Rings to Answer setting. The printer begins emitting fax reception tones to the sending fax machine and receives the fax. If you encounter problems setting up the printer with optional equipment, contact your local service provider or vendor for further assistance.
4 Computer with modem. 5 Telephone. To set up the printer on the same phone line as a computer with two phone ports 1. Remove the white plug from the port labeled 2-EXT on the back of the printer. 2. Find the phone cord that connects from the back of your computer (your computer dial-up modem) to a telephone wall jack. Disconnect the cord from the telephone wall jack and plug it into the port labeled 2EXT on the back of the printer. 3.
1 Telephone wall jack. 2 Parallel splitter. 3 DSL/ADSL filter. 4 Connect the phone cord to the port labelled 1-LINE on the back of the printer. You might need to connect the phone cord to your country/region adapter. 5 DSL/ADSL modem. 6 Computer. 7 Telephone. NOTE: You need to purchase a parallel splitter. A parallel splitter has one RJ-11 port on the front and two RJ-11 ports on the back.
4. Connect the DSL filter to the parallel splitter. 5. Connect the DSL modem to the parallel splitter. 6. Connect the parallel splitter to the wall jack. 7. Run a fax test. When the phone rings, the printer automatically answers after the number of rings you set in the Rings to Answer setting. The printer begins emitting fax reception tones to the sending fax machine and receives the fax.
4. (Optional) If your answering machine does not have a built-in phone, for convenience you might want to connect a phone to the back of your answering machine at the "OUT" port. NOTE: If your answering machine does not let you connect an external phone, you can purchase and use a parallel splitter (also known as a coupler) to connect both the answering machine and telephone to the printer. You can use standard phone cords for these connections. 5. Turn on the Auto Answer setting. 6.
Figure 5-13 Back view of the printer 1 Telephone wall jack. 2 "IN" phone port on your computer. 3 "OUT" phone port on your computer. 4 Telephone (optional). 5 Answering machine. 6 Computer with modem. 7 Connect the phone cord to the port labelled 1-LINE on the back of the printer. You might need to connect the phone cord to your country/region adapter. To set up the printer on the same phone line as a computer with two phone ports 1.
7. Turn on the Auto Answer setting. 8. Set your answering machine to answer after a low number of rings. 9. Change the Rings to Answer setting on the printer to the maximum number of rings supported by the product. (The maximum number of rings varies by country/region.) 10. Run a fax test. When the phone rings, your answering machine answers after the number of rings you have set, and then plays your recorded greeting. The printer monitors the call during this time, "listening" for fax tones.
Figure 5-14 Example of a parallel splitter To set up the printer with a computer DSL/ADSL modem 1. Obtain a DSL/ADSL filter from your DSL/ADSL provider. NOTE: Phones in other parts of the home/office sharing the same phone number with DSL/ADSL service need to be connected to additional DSL/ADSL filters, to avoid noise when making voice calls. 2. Connect one end of the phone cord to the DSL/ADSL filter, and then connect the other end to the port labeled 1-LINE on the back of the printer.
Since your computer dial-up modem shares the phone line with the printer, you cannot use both your modem and the printer simultaneously. For example, you cannot use the printer for faxing if you are using your computer dial-up modem to send an email or access the Internet. There are two different ways to set up the printer with your computer based on the number of phone ports on your computer. Before you begin, check your computer to see if it has one or two phone ports.
5. If your modem software is set to receive faxes to your computer automatically, turn off that setting. NOTE: If you do not turn off the automatic fax reception setting in your modem software, the printer cannot receive faxes. 6. Turn off the Auto Answer setting. 7. Run a fax test. You must be available to respond in person to incoming fax calls, or the printer cannot receive faxes.
6 Web Services This section contains the following topics: ● What are Web Services? ● Set up Web Services ● Use Web Services ● Remove Web Services What are Web Services? The printer offers innovative, web-enabled solutions that can help you quickly access the Internet, obtain documents, and print them faster and with less hassle—and all without using a computer. NOTE: To use these web features, the printer must be connected to the Internet (either using an Ethernet cable or wireless connection).
3. Touch Accept to accept the Web Services terms of use and enable Web Services. 4. On the screen that appears, touch OK to allow the printer to automatically check for product updates. NOTE: If prompted for proxy settings and if your network uses proxy settings, follow the onscreen instructions to set up a proxy server. If you do not have the proxy details, contact your network administrator or the person who set up the network. 5.
● HP ePrint ● Print apps HP ePrint To use HP ePrint , do the following: ● Be sure you have an Internet- and email-capable computer or mobile device. ● Enable Web Services on the printer. For more information, see Set up Web Services. TIP: For more information about managing and configuring HP ePrint settings and to learn about the latest features, visit HP Connected (this site might not be available in all countries/regions). To print documents using HP ePrint 1.
TIP: ● To learn more about individual print apps and to add, configure, or remove print apps, visit HP Connected (www.hpconnected.com). This site might not be available in all countries/regions. ● You can also turn off print apps from EWS. To do so, open EWS (see Embedded web server), click the Web Services tab and turn off the setting; or click the Settings tab, and select the desired option on the Administrator Settings page. Remove Web Services Use the following instructions to remove Web Services.
7 Work with cartridges To ensure the best print quality from the printer, you need to perform some simple maintenance procedures. TIP: If you have problems copying documents, see Printing issues.
NOTE: This printer is designed for ink cartridges to be used until they are empty. Refilling cartridges prior to depletion might cause your printer to fail. If this happens, insert a new cartridge (either genuine HP or compatible) to continue printing. Related topics ● Check the estimated ink levels Check the estimated ink levels You can check the estimated ink levels from the printer software or from the printer control panel.
2. Open the cartridge access door. NOTE: Wait until the print carriage stops moving before proceeding. 3. Press the front of the cartridge to release it, and then remove it from the slot. 4. Remove the new cartridge from its packaging. 5. Using the color-coded letters for help, slide the cartridge into the empty slot until it is securely installed in the slot. Make sure that the color-coded letter on the cartridge matches that on the slot. 96 6.
Order cartridges To order cartridges, go to www.hp.com . (At this time, some portions of the HP website are available in English only.) Ordering cartridges online is not supported in all countries/regions. However, many countries have information on ordering by telephone, locating a local store and printing a shopping list. In addition, you can visit the www.hp.com/buy/supplies page to obtain information about purchasing HP products in your country.
NOTE: To turn the usage information function on, restore the factory defaults. For more information about how to restore the defaults, see Restore original factory defaults and settings. NOTE: You can continue to use the cartridge in the HP printer if you turn off the memory chip's ability to collect the printer's usage information. Cartridge warranty information The HP cartridge warranty is applicable when the cartridge is used in its designated HP printing device.
8 Network setup Additional advanced settings are available from the printer's home page (embedded web server or EWS). For more information, see Embedded web server.
If you cannot find the network name or the security password or cannot remember this information, see the documentation provided with your computer or with the wireless router. If you still cannot find this information, contact your network administrator or the person who set up the wireless network. Set up the printer on your wireless network Use the Wireless Setup Wizard or Wi-Fi Protected Setup from the printer control panel display to set up wireless communication.
To change from a USB connection to a wireless network (Windows) Before you proceed, go through the list at Before you begin. 1. Open the HP printer software. For more information, see Open the HP printer software (Windows). 2. Click Tools. 3. Click Device Setup & Software. 4. Select Convert a USB connected printer to wireless. Follow the onscreen instructions. To change from a USB or Ethernet connection to a wireless connection (OS X and macOS) 1.
6. Select the new USB printer from the list. 7. Choose your printer model name from the Use pop-up menu. 8. Click Add. Test the wireless connection Print the wireless test report for information about the printer wireless connection. The wireless test report provides information about the printer status, hardware (MAC) address, and IP address. If there is a problem with the wireless connection or if a wireless connection attempt failed, the wireless test report also provides diagnostic information.
To print network settings Do one of the following: ● From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard. Touch (Wireless) or (Ethernet) to display the network status screen. Touch Print Details to print the network configuration page. ● From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, touch ( Setup ), touch Reports , and then touch Network Configuration Page.
7. Enter your changes, and then touch Done . 8. Touch OK . Use Wi-Fi Direct With Wi-Fi Direct, you can print wirelessly from a computer, smart phone, tablet, or other wireless-capable device—without connecting to an existing wireless network. Guidelines for using Wi-Fi Direct ● Make sure your computer or mobile device has the necessary software. – If you are using a computer, make sure you have installed the HP printer software.
To print from a wireless-capable mobile device that supports Wi-Fi Direct Make sure you have installed the latest version of HP Print Service Plugin on your mobile device. NOTE: If your mobile device does not support Wi-Fi, you are not able to use Wi-Fi Direct. 1. Make sure you have turned on Wi-Fi Direct on the printer. 2. Turn on Wi-Fi Direct on your mobile device. For more information, see the documentation provided with the mobile device. 3.
a. Open the HP printer software. For more information, see Open the HP printer software (Windows). b. Click Tools. c. Click Device Setup & Software, and then select Connect a new device. NOTE: If you have previously installed the printer over USB and want to convert to Wi-Fi Direct, do not select the Convert a USB connected printer to wireless option. 6. d. When the Connection Options screen appears, select Wireless. e. Select your HP printer from the detected printer list. f.
9 Printer management tools This section contains the following topics: ● Toolbox (Windows) ● HP Utility (OS X and macOS) ● Embedded web server Toolbox (Windows) The Toolbox provides maintenance information about the printer. To open the Toolbox 1. Open the HP printer software. For more information, see Open the HP printer software (Windows). 2. Click Print, Scan & Fax . 3. Click Maintain Your Printer.
About cookies The embedded Web server (EWS) places very small text files (cookies) on your hard drive when you are browsing. These files let the EWS recognize your computer the next time you visit. For example, if you have configured the EWS language, a cookie helps remember which language you have selected so that the next time you access the EWS, the pages are displayed in that language.
Embedded web server cannot be opened Check your network setup ● Make sure you are not using a phone cord or a crossover cable to connect the printer to the network. ● Make sure the network cable is securely connected to the printer. ● Make sure the network hub, switch, or router is turned on and working correctly. Check the computer ● Make sure the computer that you are using is connected to the same network as the printer.
10 Solve a problem The information in this section suggests solutions to common problems. If your printer is not operating correctly and these suggestions did not solve your problem, try using one of the support services listed in HP support to obtain assistance.
Read general instructions in the Help for clearing paper jams Paper jams can occur in several locations inside the printer. CAUTION: To prevent possible damage to the printhead, clear paper jams as soon as possible. To clear a paper jam from Tray 1 1. Pull Tray 1 out of the printer completely. 2. Check the gap in the printer where the input tray was. Reach into the gap and remove the jammed paper. 3. Insert Tray 1 back into the printer. To clear a paper jam from Tray 2 1.
2. Check the gap in the printer where the input tray was. Reach into the gap and remove the jammed paper. 3. Insert Tray2 back into the printer. To clear a paper jam from the front of the printer NOTE: Do not turn off the printer when there is a paper jam in the front of the printer. 1. Open the cartridge access door. 2. If the print carriage is not obstructed, move the print carriage to the far right of the printer and remove the jammed paper.
3. Close the cartridge access door. To clear a paper jam from the rear of the printer ENWW 1. Turn to the rear of the printer. 2. Press the two tabs on the rear access door and open the door. 3. Remove any jammed paper. 4. Press the two buttons on the paper path cover, and pull the cover out of the printer completely. 5. Remove any jammed paper.
6. Insert the paper path cover back into the printer. 7. Close the rear access door. To clear a paper jam from the document feeder 1. Lift the cover of the document feeder. 2. Pull any jammed paper out of the rollers.
3. Close the cover of the document feeder until it snaps into space. 4. Lift up the document feeder tray. 5. Remove any jammed paper under the tray. 6. Put down the document feeder tray. 7. Lift the scanner lid to check, if there is jammed paper, remove it. Clear a print carriage jam Resolve a print carriage jam Use an HP online troubleshooting wizard. If something is blocking the print carriage or it does not move easily, get step-by-step instructions.
NOTE: The HP online troubleshooting wizards may not be available in all languages. Read general instructions in the Help for clearing a print carriage jams Remove any objects, such as paper, that are blocking the print carriage. NOTE: Do not use any tools or other devices to remove jammed paper. Always use caution when removing jammed paper from inside the printer. Learn how to avoid paper jams To help avoid paper jams, follow these guidelines. ● Remove printed papers from the output tray frequently.
● ● – Ensure that the stack of paper is aligned with the appropriate paper size lines on the bottom of the input tray, and does not exceed the stack height indicated by one or more label on the side or paper-width guide of the input tray. – Make sure paper in the tray is not curled. Uncurl paper by bending it in the opposite direction of the curl. Pages are skewing – Make sure the paper loaded in the input tray is aligned to the paper-width guides.
Read general instructions in the Help for unable to print issues To resolve print issues (Windows) Make sure that the printer is turned on and that there is paper in the tray. If you are still unable to print, try the following in order: 1. Check for error messages from the printer display and resolve them by following the onscreen instructions. 2. If your computer is connected to the printer with a USB cable, disconnect and reconnect the USB cable.
b. ● Windows Vista: From the Windows Start menu, click Control Panel, and then click Printers. ● Windows XP: From the Windows Start menu, click Control Panel, and then click Printers and Faxes. Make sure the correct printer is set as the default printer. The default printer has a check mark in a black or green circle next to it. 5. c. If the wrong printer is set as the default printer, right-click the correct printer and select Set as Default Printer. d. Try using your printer again.
Windows Vista i. From the Windows Start menu, click Control Panel, System and Maintenance, Administrative Tools. ii. Double-click Services. iii. Right-click the Print Spooler service, and then click Properties. iv. On the General tab, next to Startup type, make sure that Automatic is selected. v. If the service is not already running, under Service status, click Start, and then click OK. Windows XP b. i. From the Windows Start menu, right click My Computer. ii.
To check the power connection and reset the printer 1. Make sure the power cord is firmly connected to the printer. 1 Power connection to the printer 2 Connection to a power outlet 2. Look at the Power button located on the printer. If it is not lit, the printer is turned off. Press the Power button to turn on the printer. NOTE: If the printer is not receiving electrical power, connect it to another power outlet. 3. With the printer turned on, disconnect the power cord from the side of the printer.
d. 4. ● Resume: Continue a paused print job. ● Pause Printer: Pause all print jobs in the print queue. If you made any changes, try to print again. Restart the computer.
6. Review the blue, magenta, yellow, and black boxes on the diagnostics page. If you are seeing streaks in the color and black boxes, or no ink in portions of the boxes, then automatically clean the printhead. To clean the printhead from the printer software 7. a. Load Letter, A4, or Legal unused plain white paper into the input tray. b. Open the HP printer software. For more information, see Open the HP printer software (Windows). c.
To print a test page a. Load Letter or A4 plain, white paper in the input tray. b. Open HP Utility. NOTE: 7. HP Utility is located in the HP folder in the Applications folder. c. Select your printer from the list of devices at the left of the window. d. Click Test Page. e. Click the Print Test Page button, and follow the onscreen instructions. If the diagnostic page shows steaks or missing portions of the text or colored boxes, clean the printhead automatically.
To print a diagnostics page from the printer display 6. a. Load Letter, A4, or Legal unused plain white paper into the input tray. b. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, and then touch ( Setup ). c. Touch Reports . d. Touch Print Quality Report. Review the blue, magenta, yellow, and black boxes on the diagnostics page.
Fax issues Run the fax test report first to see if there is a problem with your fax setup. If the test passes and you are still having problems faxing, check the fax settings listed in the report to verify that the settings are correct. Run the fax test You can test your fax setup to check the status of the printer and to make sure it is set up correctly for faxing. Perform this test only after you have completed fax setup on the printer.
● If you are using a phone splitter, this can cause faxing problems. (A splitter is a two-cord connector that plugs into a telephone wall jack.) Try removing the splitter and connecting the printer directly to the telephone wall jack. After you resolve any problems found, run the fax test again to make sure it passes and the printer is ready for faxing. If the Fax Hardware Test continues to fail and you experience problems faxing, contact HP support. Go to www.support.hp.com .
Figure 10-1 Back view of the printer 1 Telephone wall jack. 2 Connect the phone cord to the port labelled 1-LINE on the back of the printer. 2. After you have connected the phone cord to the port labeled 1-LINE, run the fax test again to make sure it passes and the printer is ready for faxing. 3. Try to send or receive a test fax.
The "Dial Tone Detection" test failed ● Other equipment, which uses the same phone line as the printer, might be causing the test to fail. To find out if other equipment is causing a problem, disconnect everything from the phone line, and then run the test again.
● If you are using a phone splitter, this can cause faxing problems. (A splitter is a two-cord connector that plugs into a telephone wall jack.) Try removing the splitter and connecting the printer directly to the telephone wall jack. After you resolve any problems found, run the fax test again to make sure it passes and the printer is ready for faxing. If the Fax Line Condition test continues to fail and you experience problems faxing, contact your telephone company and have them check the phone line.
● Make sure you used the phone cord supplied in the box with the printer to connect to the telephone wall jack. One end of the phone cord should be connected to the port labeled 1-LINE on the back of the printer and the other end to your telephone wall jack, as shown in the illustration. 1 Telephone wall jack. 2 Connect the phone cord to the port labelled 1-LINE on the back of the printer.
If the phone line is still noisy, contact your telephone company. For information on turning your DSL modem off, contact your DSL provider for support. ● If you are using a phone splitter, this can cause faxing problems. (A splitter is a two-cord connector that plugs into a telephone wall jack.) Try removing the splitter and connecting the printer directly to the telephone wall jack.
To find out if other equipment is causing a problem, disconnect everything except the printer from the phone line, and then try to receive a fax. If you can receive faxes successfully without the other equipment, one or more pieces of the other equipment is causing problems; try adding them back one at a time and receiving a fax each time, until you identify which equipment is causing the problem.
Fix wireless connection Choose one of the following troubleshooting options. HP Print and Scan Doctor The HP Print and Scan Doctor is a utility that will try to diagnose and fix the issue automatically. NOTE: Use an HP online troubleshooting wizard This utility is only available for Windows operating system. ● Troubleshoot your wireless problem, whether your printer has never been connected or it was connected and is no longer working.
▲ From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, and then touch (Wi-Fi Direct). 2. From your wireless computer or mobile device, turn on the Wi-Fi connection, and then search for and connect to the Wi-Fi Direct name of your printer. 3. Enter the Wi-Fi Direct password when prompted. 4. If you are using a mobile device, make sure you have installed a compatible printing app. For more information about mobile printing, visit www.hp.
Resolve printer failure Complete the following steps to resolve printer failure problems: 1. Press (the Power button) to turn off the printer. 2. Unplug the power cord, and then plug in the power cord again. 3. Press (the Power button) to turn on the printer. If this problem persists, write down the error code provided in the message, and then contact HP support. For more information about contacting HP support, see HP support.
Network configuration page If the printer is connected to a network, you can print a network configuration page to view the network settings for the printer and a list of networks detected by your printer. The last page of the report includes a list of all detectable wireless networks in the area, along with signal strength and the channels being used. This might help you select a channel for your network which is not heavily used by other networks (which will improve network performance).
● – Make sure the printer's email address is correct. – Make sure that the printer's email address is the only address listed in the “To” line of the email message. If other email addresses are listed in the “To” line, the attachments you are sending might not print. – Make sure you are sending documents that meet the HP ePrint requirements. For more information, visit HP Connected (this site might not be available in all countries/regions).
2. Clean the scanner glass and lid backing by using a soft, lint-free cloth that has been sprayed with a mild glass cleaner. CAUTION: Use only glass cleaner to clean the scanner glass. Avoid cleaners that contain abrasives, acetone, benzene, and carbon tetrachloride, all of which can damage the scanner glass. Avoid isopropyl alcohol because it can leave streaks on the scanner glass. CAUTION: Do not spray the glass cleaner directly on the scanner glass.
2. Lift the document feeder cover. This provides easy access to the rollers (1) and separator pad (2). 1 Rollers 2 Separator pad 3. Lightly dampen a clean lint-free cloth with distilled water, then squeeze any excess liquid from the cloth. 4. Use the damp cloth to wipe any residue off the rollers or separator pad. NOTE: 5. If the residue does not come off using distilled water, try using isopropyl (rubbing) alcohol. Close the cover of the document feeder.
The printer automatically aligns the printhead during the initial setup. NOTE: Cleaning uses ink, so clean the printhead only when necessary. The cleaning process takes a few minutes. Some noise might be generated in the process. Always use the Power button to turn off the printer. Turning the printer off improperly can cause print quality problems. To clean or align the printhead 1. Load Letter or A4 unused plain white paper into the input tray. For more information, see Load paper. 2.
4. Touch Restore Factory Defaults. A message appears stating that the factory defaults will be restored. 5. Touch Continue. To restore the printer to the original network settings 1. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, and then touch ( Setup ). 2. Touch Network Setup. 3. Touch Restore Network Settings. A message appears stating that the network defaults will be restored. 4. Touch Yes. 5.
Chat with an HP support agent online. Call an HP support agent. When contacting HP support, be prepared to provide the following information: ● Product name (Located on the printer, such as HP OfficeJet Pro XXXX) ● Product number (located near the cartridge access area) ● Serial number (located on the back or bottom of the printer) Register printer By taking just a few quick minutes to register, you can enjoy quicker service, more efficient support, and product support alerts.
A Technical information This section contains the following topics: ● Specifications ● Regulatory notices ● Environmental product stewardship program Specifications The information here is subject to change without notice. For more product specifications, see the Product Data Sheet at www.support.hp.com . System requirements ● For information about software and system requirements or future operating system releases and support, visit the HP online support website at www.support.hp.com .
Output tray capacity ● Plain paper sheets (60 to 105 g/m2 [16 to 28 lb]): – A size plain paper: Up to 75 – B size plain paper: Up to 50 ● Envelopes: Up to 30 ● Index cards: Up to 35 ● Photo paper sheets: Up to 25 Document feeder capacity ● Plain paper sheets (60 to 90 g/m2 [16 to 24 lb]): Up to 35 Paper size and weights For the list of supported paper sizes, see the HP printer software.
– ● 216 x 356 mm (8.5 inches x 14 inches) Maximum scan size from document feeder: – One-sided: 216 x 356 mm (8.5 x 14 inches) Fax specifications ● Walk-up black-and-white and color fax capability. ● Manual fax send and receive. ● Automatic busy redial up to five times (varies by model). ● Automatic no-answer redial up to one time (varies by model). ● Confirmation and activity reports. ● CCITT/ITU Group 3 fax with Error Correction Mode. ● Up to 33.6 Kbps transmission.
● Regulatory information for wireless products Regulatory model identification number For regulatory identification purposes, your product is assigned a Regulatory Model Number. The Regulatory Model Number for your product is SNPRC-1500-02. This regulatory number should not be confused with the marketing name (HP OfficeJet Pro 7730 Wide Format All-in-One series, etc.) or product numbers (Y0S19A, etc.).
– CAUTION: IEEE 802.11x wireless LAN with 5.15-5.35 GHz frequency band is restricted for indoor use only for all countries reflected in the matrix. Using this WLAN application outdoor might lead to interference issues with existing radio services. Declaration of conformity Declaration of conformity can be found at www.hp.eu/certificates.
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率 或變更設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改 善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及 醫藥用電波輻射性電機設備之干擾。 Environmental product stewardship program HP is committed to providing quality products in an environmentally sound manner. Design for recycling has been incorporated into this product. The number of materials has been kept to a minimum while ensuring proper functionality and reliability.
● California Perchlorate Material Notice Eco-Tips HP is committed to helping customers reduce their environmental footprint. Please visit the HP Eco Solutions website for more information on HP’s environmental initiatives. www.hp.
Additional ENERGY STAR certified imaging product model information is listed at: www.hp.com/go/energystar Disposal of waste equipment by users This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment.
Declaration of the Presence Condition of the Restricted Substances Marking (Taiwan) 限用物質含有情況標示聲明書 Declaration of the Presence Condition of the Restricted Substances Marking 限用物質及其化學符號 Restricted substances and its chemical symbols 單元 Unit 鉛 汞 鎘 六價鉻 多溴聯苯 多溴二苯醚 Lead Mercury Cadmium (Pb) (Hg) (Cd) Hexavalent chromium Polybrominated biphenyls (Cr+6) (PBB) Polybrominate d diphenyl ethers (PBDE) 0 0 0 0 0 0 電線 (Cables) 0 0 0 0 0 0 印刷電路板 － 0 0 0 0 0 列印引擎(Print Engine) － 0 0
The Table of Hazardous Substances/Elements and their Content (China) 产品中有害物质或元素的名称及含量 根据中国《电器电子产品有害物质限制使用管理办法》 有害物质 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 外壳和托盘 ◯ ◯ ◯ ◯ ◯ ◯ 电线 ◯ ◯ ◯ ◯ ◯ ◯ 印刷电路板 X ◯ ◯ ◯ ◯ ◯ 打印系统 X ◯ ◯ ◯ ◯ ◯ 显示器 X ◯ ◯ ◯ ◯ ◯ 喷墨打印机墨盒 ◯ ◯ ◯ ◯ ◯ ◯ 驱动光盘 X ◯ ◯ ◯ ◯ ◯ 扫描仪 X ◯ ◯ ◯ ◯ ◯ 网络配件 X ◯ ◯ ◯ ◯ ◯ 电池板 X ◯ ◯ ◯ ◯ ◯ 自动双面打印系统 ◯ ◯ ◯ ◯ ◯ ◯ 外部电源 X ◯ ◯ ◯ ◯ ◯ 部件名称 本表格依据 SJ/T 11364 的规定编制。 ◯：表
concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for where allowed pursuant to the exemptions set in Schedule 2 of the Rule. Restriction on hazardous substances statement (Turkey) Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur EPEAT Most HP products are designed to meet EPEAT. EPEAT is a comprehensive environmental rating that helps identify greener electronics equipment. For more information on EPEAT go to www.epeat.net.
标识上显示的能耗数据是根据典型配置测量得出的数据，此类配置包含登记备案的打印机依据复印 机、打印机和传真机能源效率标识实施规则所选的所有配置。因此，该特定产品型号的实际能耗可能 与标识上显示的数据有所不同。 要了解规范的更多详情，请参考最新版的 GB 21521 标准。 Battery disposal in Taiwan European Union Battery Directive This product contains a battery that is used to maintain data integrity of real time clock or product settings and is designed to last the life of the product. Any attempt to service or replace this battery should be performed by a qualified service technician.
Index A accessibility 2 accessories setup 13 ADSL, fax setup with parallel phone systems 73 align printhead 140 answer ring pattern change 63 parallel phone systems 74 answering machine fax tones recorded 133 set up with fax (parallel phone systems) 83 set up with fax and modem 84 automatic fax reduction 59 B backup fax 57 baud rate 65 black and white pages fax 52 blocked fax numbers set up 59 both sides, print on 37 broadcast faxing send 55 buttons, control panel 7, 8 C carriage clear carriage jams 115 car
DSL, set up (parallel phone systems) 73 error correction mode 56 error reports 67 forwarding 58 header 62 Internet Protocol, over 66 ISDN line, set up (parallel phone systems) 74 line condition test, failed 129 log, clear 68 log, print 68 manual receive 57 modem and answering machine, shared with (parallel phone systems) 84 modem and voice line, shared with (parallel phone systems) 80 modem and voice mail, shared with (parallel phone systems) 87 modem, shared with (parallel phone systems) 77 monitor dialing
OS X HP Utility 107 output tray locating 6 P paper clear jams 110 HP, order 12 load tray 14 selecting 12 skewed pages 117 specifications 145 troubleshoot feeding 116 paper-feed problems, troubleshoot 116 parallel phone systems answering machine setup 83 countries/regions with 69 distinctive ringing setup 74 DSL setup 73 ISDN setup 74 modem and answering machine setup 84 modem and voice mail setup 87 modem setup 77 modem shared with voice line setup 80 PBX setup 74 separate line setup 72 setup types 70 share
computer modem and answering machine (parallel phone systems) 84 computer modem and voice line (parallel phone systems) 80 computer modem and voice mail (parallel phone systems) 87 distinctive ringing 63 distinctive ringing (parallel phone systems) 74 DSL (parallel phone systems) 73 fax scenarios 70 fax, with parallel phone systems 69 ISDN line (parallel phone systems) 74 PBX system (parallel phone systems) 74 separate fax line (parallel phone systems) 72 shared phone line (parallel phone systems) 75 test f
