INE CADUCEI ON mmm mmm 03 IMPORTANCE TIPS 03 Safety Flight Inst Ructions oo omen ooo 04 Description of each mm mere eee 05 Install instructions: Aircraft unpacking (PNP mere 06 Install instructions: Install the nose cone and eee 07 Install instructions: Install the left and right flat ccc 07 Install instructions: Install the vertical tail ooo 08 Install instructions: Install the Wing Po Weer inner 08 Install instructions: Install the main wing 09 First test and adjustment after 09 First test and adjustment
S-DEF 90mm HEM-262 Introduction Thank you so much for purchasing this plane, What you have now is the test plane product of DUETS. This model has the following features: OL Simulate the shape, reproduce the classic style of the real machine with varietals. thee whole machine is made of 35 times EPO and high-strength engineering plastics, with good crash worthiness.
HEADSETS’ Safety Flight Instructions Strongly suggestion: users while enjoying the flying, please ensure that you are in a safe and reasonable environment. 1. It is better to try to choose an empty airspace, with no obstacles when you fly. 2. Stay away from people, animals, buildings, trees, water and other obstacles during flying. 3. Please keep the radio transmitter in your hand during the flight to control the model at any time to prevent accidents, 4.
HEADSETS’ — Install instructions the manual. 1.
S-DEF 90mm HEM-262 — Install instructions 2. Installation of nose cone and fuselage: take out the nose cone and body from PE bag and place them on the flat and clean table. Apply EPO glue to the contact section of nose cone and fuselage respectively to fix them. 3.
HEADSETS’ — Install instructions 4. Install the ve) 1 tail: First install the vertical tail at the designated position of the fuselage, and ensure that the signal wiring between the vertical tail end and the fuselage end is well connected, after installation in place, fix the bottom with screws. {HM3 X 10mm X 2pcs). {Note: the color of the wire must be inserted well to the color of the wire, and the wire should not be inserted reversely.) 5.
S-DEF 90mm HEM-262 r— First test and adjustment after assembly 6. Install the main wing: Pass the main wing reinforcement red (¢ 16mm X ¢ 12mm X [670mm) through the designated hole position of the fuselage, ensure that the extension length of the main wing reinforcement bar at the left and right ends of the fuselage is equal, and then align the hole position of the left and right main wing with the main wing reinforcement rod, and insert the reinforcing rod.
HEADSETS’ r— First test and adjustment after assembly 5. Check the Super Integrated Control Box S-BUS mode channel settings. The factory default channel is: S-BUS Setting (Note: You can change the default gear switch position according to your own custom channel.) 1.AUX1 CH Aileron {default CH1) TABLEAUX CH Spare(default CHT} 2.AUX2 Ch Elevator {default CH2) ~~ 8.AUX8 CH Spare 3.AUX3 CH Rudder (default CH4) 9.A/B LIGHT CH Spare{default CH3} integrated control box S-BUS | 4.AUX4 CH Flap (default CHE) 10.
S-DEF 90mm HEM-262 r— First test and adjustment after assembly the same plane with the wing; entrance); Suggest the amount of servo: Cr -20mm AIL EXP Right model throttle radio transmitter men 7.Elevator detection: check whether the lifting action is correct Aileron standard action Co 6.Aileron adjustment: After completing the setting, start to adjust the standard position of the rudder surface. The aileron rudder surface should be on the same plane as the wing.
HEADSETS’ r— First test and adjustment after assembly 8.Elevating adjustment: After completing the setting, start to adjust the standard position of the rudder surface. The elevator surface should be on the same plane as the horizontal tail.
S-DEF 90mm HEM-262 r— First test and adjustment after assembly bar. adjustment: wing; a When the rudder action is opposite to the specified action, you can find the servo reverse setting menu in the remote-control menu, and switch forward and reverse in the rudder item Possible rudder reverse action 4 } eal Physical adjustment adjustment: change the length of the rudder surface by adjusting the length of the lever to keep it on the same plane with the 10.
HEADSETS’ r— First test and adjustment after assembly 11.Flap detection: check whether the flaps are correct Right model throttle radio transmitter Flaps standard action 12.
S-DEF 90mm HEM-262 First test and adjustment after assembly 13. Ground test and adjustment: After the above process is gradually completed, power the plane and do straight slide test to check whether the stroke volume of the front steering servo is full. If the steering is yaw or the steering angle is too large, it can be adjusted by physical adjustment or system adjustment: yaw adjustment: ©. physical adjustment: Complete it by adjusting the length of the front wheel steering rod; @.
HEADSETS’ — First test and adjustment after assembly 14.Center of gravity detection before take-off: Before starting the machine, you need to confirm whether the position of the center of gravity of the _ .isusmivm® machine is correct. The center of gravity is located a behind the front edge of the main wing: 145~150mm. ier A general method for measuring the center of gravity 145-150mm Battery assembly diagram 15.
S-DEF 90mm HEM-262 Specification and configuration Specifications: Length Flying time Loading of airfoil surface Body Surface Treatment PNP assembly difficulty Working temperature Configuration: Control system EDF Power battery Servo Brake function Aileron Horizontal tail Reinforced gyro Center of gravity 1626mm /64 in About 5 minutes Matte environmental water-borne paint + decal [Ik (minsters) 0°C ~ 40°C MFC-2085-DR S-DEF 90mm blade X2 PCS /5000~6000mAh / 45C / Li-Po X 2 PCS (Selective configuration) 12gX4
© €) company address thud industry Ark, Gang Industry District, Aided, Hymen Town, Guangdong City, Guangdong Province,China (Post:523926) 9 Production address : Building F6, Standardized Factory Buildings , Xix Industrial Park, Xix District, Anshan City, Guizhou Province, China (Post: 561099) Copyright © HEADSETS, All Rights Reserved, Designed by DUETS, Printed & Made in China 202010
