OPERATING INSTRUCTIONS PAPER SHREDDER Combination with HSM KP 80 HSM FA 500.2 english Keep this instruction for future use! 1.655.999.
FA 500.2 Contents 1. Proper use, warranty.................................................................................................................3 2. Safety instructions.....................................................................................................................3 3. Overview ...................................................................................................................................4 4. Dimensions ................................................
FA 500.2 1. Proper use, warranty The document shredder is designed for destroying paper and cardboard, as well as store cards, credit cards, CDROMs and floppy discs. Its sturdy drive mechanism is not damaged by paper clips and staples and is even suitable for shredding whole files and folders. Our general business conditions are applicable. We provide a one year warranty for the document shredder. The warranty period is 6 months when used in multiple shifts.
FA 500.2 3.
FA 500.2 820 1925 max. 630 HSM FA 500.2 Stand alone-version 1255 500 HSM FA 500.2 Combination-version 960 1155 880 560 1155 500 880 910 630 500 2500 1590 960 1410 1185 1925 max. 1410 1185 4.
FA 500.2 • 5. Transportation, installation • • • • • • During transport, observe the high centre of gravity of the paper shredder! Place the pallet with the shredder in its packaging on a smooth, level surface. Observe the instructions for unpacking. If you need to move the shredder through narrow doors, you can wait until it is at its final location before fitting the loading tray. Without the tray, the machine is only 880 mm wide.
FA 500.2 • Insert the connecting screw (5) and the clamp (6) on the end of the hose and secure the unit on the oiler. 5 • 6 • • Solo machine: Lock the front castors by pressing down the brake lever. Combination version: The assembly of the shredder with the baling press is described in the operator‘s manual of the Shredder press combination. Pour the oil into the oiler container from the two bottles supplied. 6.
FA 500.2 7. Start-up and inspecting the safety devices Safety flap on the feed belt Check that the safety devices are working properly: • At the start of each shift • After any maintenance or repair work Do not start the machine until you have checked the safety devices and found them to be in perfect working order. If any defect arises during operation stop the machine immediately and make sure it is corrected. Switching on the paper shredder • Pull out the emergency stop button.
FA 500.2 Safety switch on the inspection door (only stand alone-version) Shredding material • Press the green start button. ` The cutting block and feed belt start up. Open the inspection door. The shredder must switch off immediately and the ”Safety circuit interrupted” LED must light up. The machine will only start again once you have closed the inspection door.
FA 500.2 8. Malfunctions 9. Maintenance and care Check the following before calling customer service: • Is the power plug connected? • Is the shredder switched on? • Is there a paper jam in the shredder? • Has the motor been overloaded? Cleaning the cutting unit if the cutting quality deteriorates or the machine becomes noisy • Let the shredder run without feeding in any paper. • Push the lever of the oiler down several times. Paper jam You have fed in too much paper.
FA 500.2 Checking the chain tension (twice yearly) Greasing the drive chains and cogs (twice yearly) • Switch off the shredder. • Switch off the shredder. • Pull out the power plug. • Pull out the power plug. • Remove the left side cover. 1 • Remove the left and right side covers. • Grease the cogs and the drive chains from the motor to the cutting apparatus, the cutting block to the feed belt and the cutting block to the regulating roller.
FA 500.2 Tightening the feed belt Cleaning the shredder: The feed belt should not slip when loaded with material. • • • Switch off the shredder. • Remove the feeding table and the left and right side covers. Switch off the shredder and disconnect the mains plug. When cleaning, only use a soft cloth and a mild soapwater solution. Never use scouring agents, cleaning fluid, petroleum or thinners.
FA 500.2 11. Technical Data Cutting type Cross cut Cut size (mm) 10.5 x 40 - 76 7.5 x 40 - 80 6 x 40 - 53 2 2 3 600 - 650 510 - 550 500 - 550 425 - 470 400 - 450 340 - 350 Safety level DIN 32757 – 1 Cutting capacity (sheets), DIN A4, 2 70 g/m 80 g/m2 Cutting speed 210 mm/s Effective width 500 mm Weight approx. 725 kg Voltage 3 x 400 V, 50 Hz Rated power 9.2 kW Rated current 18.
FA 500.2 12.
Solo 400 V FA 500.
Solo 400 V FA 500.
FA 500.
Kombi 400 V FA 500.
Kombi 400 V FA 500.
Kombi 400 V FA 500.