PDA Phone User Manual www.htc.
Please Read Before Proceeding THE BATTERY IS NOT CHARGED WHEN YOU TAKE IT OUT OF THE BOX. DO NOT REMOVE THE BATTERY PACK WHEN THE DEVICE IS CHARGING. YOUR WARRANTY IS INVALIDATED IF YOU OPEN OR TAMPER WITH THE DEVICE’S OUTER CASING. PRIVACY RESTRICTIONS Some countries require full disclosure of recorded telephone conversations, and stipulate that you must inform the person with whom you are speaking that the conversation is being recorded.
Macromedia, Flash, Macromedia Flash, Macromedia Flash Lite and Reader are trademarks and/or registered trademarks of Macromedia Netherlands, B.V. or Adobe Systems Incorporated. Opera® Browser from Opera Software ASA. Copyright 1995-2007 Opera Software ASA. All Rights Reserved. Sprite Backup is a trademark or service mark of Sprite Software. Copyright © 2007, Dilithium Networks, Inc. All Rights Reserved. Copyright © 2007, Esmertec AG. All Rights Reserved.
Disclaimers THE WEATHER INFORMATION, DATA AND DOCUMENTATION ARE PROVIDED “AS IS” AND WITHOUT WARRANTY OR TECHNICAL SUPPORT OF ANY KIND FROM HTC.
Limitation of Damages TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL HTC OR ITS PROVIDERS BE LIABLE TO USER OR ANY THIRD PARTY FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES OF ANY KIND, IN CONTRACT OR TORT, INCLUDING, BUT NOT LIMITED TO, INJURY, LOSS OF REVENUE, LOSS OF GOODWILL, LOSS OF BUSINESS OPPORTUNITY, LOSS OF DATA, AND/OR LOSS OF PROFITS ARISING OUT OF, OR RELATED TO, IN ANY MANNER, OR THE DELIVERY, PERFORMANCE OR NONPERFORMANCE OF OBLIGATIONS, OR
SAFETY PRECAUTIONS FOR POWER SUPPLY UNIT • Use the correct external power source A product should be operated only from the type of power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult your authorized service provider or local power company. For a product that operates from battery power or other sources, refer to the operating instructions that are included with the product.
• Always keep the battery out of the reach of babies and small children, to avoid swallowing of the battery. Consult the doctor immediately if the battery is swallowed. If the battery leaks: • • Do not allow the leaking fluid to come in contact with skin or clothing. If already in contact, flush the affected area immediately with clean water and seek medical advice. • Do not allow the leaking fluid to come in contact with eyes.
SAFETY IN AIRCRAFT Due to the possible interference caused by this product to an aircraft’s navigation system and its communications network, using this device’s phone function on board an airplane is against the law in most countries. If you want to use this device when on board an aircraft, remember to turn off the phone by switching to Flight Mode.
SAFETY PRECAUTIONS FOR RF EXPOSURE • Avoid using your device near metal structures (for example, the steel frame of a building). • Avoid using your device near strong electromagnetic sources, such as microwave ovens, sound speakers, TV and radio. • Use only original manufacturer-approved accessories, or accessories that do not contain any metal. • Use of non-original manufacturer-approved accessories may violate your local RF exposure guidelines and should be avoided.
Use only the supplied integral antenna. Use of unauthorized or modified antennas may impair call quality and damage the phone, causing loss of performance and SAR levels exceeding the recommended limits as well as result in non-compliance with local regulatory requirements in your country. To assure optimal phone performance and ensure human exposure to RF energy is within the guidelines set forth in the relevant standards, always use your device only in its normal-use position.
General Precautions • Heed service markings Except as explained elsewhere in the Operating or Service documentation, do not service any product yourself. Service needed on components inside these compartments should be done by an authorized service technician or provider.
• Avoid pushing objects into product Never push objects of any kind into cabinet slots or other openings in the product. Slots and openings are provided for ventilation. These openings must not be blocked or covered. • Mounting accessories Do not use the product on an unstable table, cart, stand, tripod, or bracket. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
Contents Chapter 1 Getting Started 17 1.1 Getting to Know Your PDA Phone and Accessories..................... 18 1.2 Installing the USIM/SIM Card and Battery ................................... 22 1.3 Installing a Storage Card ............................................................... 25 1.4 Starting Up ..................................................................................... 26 1.5 The Today Screen ........................................................................... 29 1.
3.6 Smart Dialing ................................................................................. 75 3.7 Additional Dialing Information .................................................... 77 3.8 Setting Up Bluetooth SIM Access for Car Kit Phones .................. 77 Chapter 4 Setting Up Your Device 79 4.1 Basic Settings ................................................................................. 80 4.2 Personalizing the Today Screen .................................................... 83 4.
Chapter 8 Working With Company E-mails and Meeting Appointments 8.1 8.2 8.3 8.4 Chapter 9 Working With Documents and Files 9.1 9.2 9.3 9.4 9.5 129 Synchronizing with the Exchange Server .................................. 130 Working With Company E-mails ................................................. 131 Managing Meeting Requests ...................................................... 135 Finding Contacts in the Company Directory ............................. 137 139 Microsoft® Office Mobile .....
Chapter 12 Experiencing Multimedia 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 Camera ....................................................................................... 190 Camera Album ........................................................................... 202 Pictures & Videos ....................................................................... 206 Windows Media® Player Mobile ................................................ 208 Streaming Media ................................................
Chapter 1 Getting Started 1.1 Getting to Know Your PDA Phone and Accessories 1.2 Installing the USIM/SIM Card and Battery 1.3 Installing a Storage Card 1.4 Starting Up 1.5 The Today Screen 1.6 The Start Menu 1.7 Quick Menu 1.8 HTC Home™ 1.9 TouchFLO™ 1.10 Status Icons 1.11 Programs 1.
Getting Started 1.1 Getting to Know Your PDA Phone and Accessories Top panel POWER Press to turn off the display temporarily. To turn off the power, press and hold for about 5 seconds. For more information, see “Starting Up” in this chapter. Left panel VOICE COMMAND • Press to activate or cancel voice recognition. See Chapter 14 for details. • Press and hold to record a voice note. Volume Control During a call or when playing music, slide up or down to adjust the sound volume.
Getting Started 19 Front panel Notification LEDs * See description below. Earpiece Listen to a phone call from here. Touch Screen TALK Press to answer an incoming call or dial a number. GPS Button Press to launch the GPS software. NAVIGATION WHEEL/ENTER • Use to scroll left, right, up, or down. • Rotate or press the wheel to scroll through items or screens. • Carry out a selection by pressing the center button. • When using the Camera or GPS software, rotate the NAVIGATION WHEEL to zoom in and out.
Getting Started Back panel GPS Antenna Connector Peel off the rubber cap and connect an external GPS antenna for better GPS signal reception. Note Use only the external GPS antenna with model number GA S120. Speaker 3 Megapixel Camera See Chapter 12 for details. Self-portrait Mirror Back Cover Slide the back cover downward to remove it. Bottom Panel RESET Press the RESET button with the stylus to soft-reset your device.
Getting Started 21 Accessories 4 1 7 User Manua l Read Me First 2 Screen Protector 8 5 3 6 No. Accessory 9 Function 1 Battery Insert into the device before turning it on. 2 Screen protector Protects the touch screen from scratches. 3 Stereo headset Provides a volume control slider and a Send/End button. Press the Send/End button to pick up a call or put a call on hold; press and hold the button to end the call. 4 AC adapter Recharges the battery.
Getting Started 1.2 Installing the USIM/SIM Card and Battery Always turn off your device before installing/replacing the USIM/SIM card and battery. The USIM/SIM card contains your phone number, service details, and phonebook/message memory. Your device supports both 1.8V and 3V SIM cards. Some legacy SIM cards will not function with your device. You should consult with your service provider for a replacement USIM/SIM card. There may be fees for this service.
Getting Started 23 To remove the back cover Before installing the USIM/SIM card or battery, remove the back cover. 1. Make sure your device is turned off. 2. Slide the back cover off to remove it. To install the USIM/SIM card 1. Make sure your device is turned off. 2. Push the SIM card holder to the right to unlock it and then flip the card holder up. 3. Insert the USIM/SIM card with its gold contacts facing down and its cut-off corner facing the battery compartment. Cut-off corner SIM card holder 4.
Getting Started To remove the USIM/SIM card 1. Remove the battery if it is installed. 2. Push the USIM/SIM card in to unlock the SIM card holder. 3. Flip the SIM card up, and then remove the SIM card. To install the battery Install the battery by aligning its exposed copper contacts with the battery connectors inside the battery compartment. Insert the contact’s side of the battery first, then gently push the battery into place.
Getting Started 25 1.3 Installing a Storage Card A storage card slot is located on the right side of your device. To have additional storage for your images, videos, music, and files, you can purchase a microSDTM card and insert it into the slot. To insert a microSD card 1. Pry open the storage card slot cover. 2. Insert the microSD card into the slot with the gold contacts facing up. Gold contacts Slot cover 3. Replace the card slot cover.
Getting Started 1.4 Starting Up After inserting your USIM/SIM card and battery and charging the battery, you can now power on and start using your device. Turn your device on and off To turn on the power • Press and hold the POWER button for a few seconds. When you turn on your device for the first time, a Quick Start Wizard guides you through the calibration process and the setup of regional settings, date and time, and password.
Getting Started 27 To automatically configure data connection settings 1. When you see the notification message from the Connection Setup, tap Yes. Note If you do not see the notification message, tap display the message. on the title bar to If your SIM card supports multiple network operator profiles, a message will appear with network profile choices. 2. Select the profile you want to use and tap OK. 3. Connection Setup then starts to configure your device’s data connection settings. 4.
Getting Started Calibrate the device Calibrating the touch screen involves tapping the center of a cross with the stylus as the cross moves around the screen. This process ensures that when you tap the screen with your stylus, the tapped item is activated. If your device does not accurately respond to screen taps, follow these steps to re-calibrate it: 1. Tap Start > Settings > System tab > Screen. 2.
Getting Started 29 You will still be able to receive messages and calls while your device is in Sleep mode. Pressing the POWER button again or incoming calls/messages will wake up your device. 1.5 The Today Screen The Today screen displays important information, such as upcoming appointments and status indicators. Tap items on the screen to open the associated program.
Getting Started 1.6 The Start Menu The Start menu, located at the top left corner of the Today screen, displays a list of programs. You can start a program by scrolling through the programs list and then pressing ENTER, or by tapping a program with the stylus. Open a recently-used program. Switch to the Today screen. Open a program. (The items displayed in the Start menu can be customized by tapping Start > Settings > Personal tab > Menus). Access more programs. View and change settings.
Getting Started 31 1.7 Quick Menu The Quick Menu, located at the top right corner of the Today screen, shows the currently running programs. You can quickly switch between running programs, stop programs, and see how much program memory is being used. Customize Task Manager settings. (See “Using Task Manager” in Chapter 13.) Tap this button to open the Quick Menu. Shows the total percentage of program memory in use. Tap to open Memory settings. Stop all currently running programs.
Getting Started To switch between the different components of HTC Home Do any of the following: • Touch the tabs in the toolbar using your finger. • Tap the tabs in the toolbar using the stylus. • Use the NAVIGATION CONTROL. If the toolbar is not selected, press NAVIGATION up/down first to select the toolbar. Press NAVIGATION left/right to select a tab, then press ENTER. Home Home displays the current date and local time.
Getting Started 33 Weather Weather shows you the current weather as well as weather information for the next four days of the week. The first time you use this feature, you need to select your city first to download weather information. To select your city 3 2 1 1. Select the Weather tab ( 4 ). 2. Tap the area that shows Select your city here. 3. On the Select City screen, type in the city name whose weather information you want to track, then tap .
Getting Started Shows the time that has elapsed since the last download of weather information. Tap this item to download the latest weather data. Tap this area to select another city. Current day’s weather Tap this area to view weather information for the next four days of the week. Tap this area to return to the current day’s weather. Weather for the next 4 days Tip You can also use the Wi-Fi connection of your device to download weather data.
Getting Started 35 Clear this check box if you prefer to manually download weather information. Tip • Download when roaming. Select this check box only if you want to allow automatic download of weather data when roaming. This may incur additional costs. • Temperature Scale. Choose whether to display temperature in Celsius or Fahrenheit. To check for more detailed weather information on the AccuWeather Web site, select Menu > About Weather on the Select City screen and then tap the AccuWeather.
Getting Started Touch a shortcut to remove it. Return Note To replace a shortcut, you must delete it first and then add a shortcut to a program or setting. Sound Sound provides a selection of profiles, each preconfigured with a different volume setting. It also lets you quickly change the ring tone of your device. Tap to open the phone sound settings where you can select the ring tone. Tap a button to select a profile (from left to right): Normal, Silent, Vibrate, Automatic.
Getting Started 37 1.9 TouchFLO™ TouchFLO™ is a special feature that gives you a better touch panel experience on your device. With TouchFLO, you can use your thumb or fingers to scroll and pan the screen. TouchFLO also features the Touch Cube where you can launch messaging programs, Internet Explorer® Mobile, and more. You can also add your favorite contacts, play music, and access your pictures and videos. Note Touch Cube is displayed in portrait view only.
Getting Started To navigate the Touch Cube The Touch Cube is a three-dimensional, cubic user interface. To flip the interface from one side to another, slide your thumb left or right on the touch screen. Touch Cube screens There are three sides to the Touch Cube interface: • On the first side of the interface, you can add up to nine favorite contacts. If you make calls to certain people frequently, you can add them as favorite contacts for quicker access.
Getting Started 39 When you have several phone numbers assigned to the same contact, an icon appears on the top left corner of the contact square to tell you which number is assigned to the particular square. Tap to call the number associated with the contact. Tap and hold to display the Contact card. Open the Phone program. (See Chapter 3 for details.) Open Call History. (See Chapter 3 for details.) Select a favorite contact to remove it. Return to your list of favorite contacts.
Getting Started • The second side of the interface provides quick shortcuts to your e-mail messages, text and MMS messages, the Internet, and other applications. Simply touch the icons on the screen to open the corresponding program. • On the third side of the interface, you can play back music and access the images and video files on your device. Touch this icon to open Audio Manager and play back music files. (For more information about using Audio Manager, see Chapter 12.
Getting Started 41 Finger scrolling and finger panning With TouchFLO, you can use finger scrolling and finger panning when viewing content that cannot be fit entirely on the screen, such as Web pages, documents, and messages. Finger scrolling can also be used to scroll up and down lists such as the contacts list, file list, message list, calendar appointments list, and more. Note Finger scrolling and panning works in both portrait and landscape modes.
Getting Started To use finger panning • To pan downward, touch and hold on the touch screen then drag your finger upward. • To pan upward, touch and hold on the touch screen then drag your finger downward. • To pan towards the right, touch and hold on the touch screen then drag your finger to the left. • To pan towards the left, touch and hold on the touch screen then drag your finger to the right. • You can also pan diagonally.
Getting Started 43 To go to the next or previous message While reading a message, slide your finger across the screen to go to the next or previous message. To go to the next message, slide your finger from right to left on the screen; To go to the previous message, slide your finger from left to right on the screen. To go to the next or previous messaging account While on a messaging account screen, you can slide your finger across the screen to go to next or previous messaging account.
Getting Started 1.10 Status Icons The following are some of the status icons that you may see on the device.
Getting Started 45 Icons that appear in this area GPRS connecting GPRS in use EDGE connecting Icons that appear in this area Vibrate mode Sound on Sound off EDGE in use HSDPA connecting HSDPA in use UMTS connecting UMTS in use Maximum signal strength No signal Phone is turned off No phone service Searching for phone service Voice call in progress Call on hold Calls are forwarded Dialing while no USIM/SIM card is inserted No USIM/SIM card inserted Icons that appear in this area Battery charging Battery f
Getting Started 1.11 Programs The following are programs you can find on your device or install from the Applications Disc. Programs in the Start Menu Icon Description Phone Make and receive calls, switch between calls, and set up conference calling. Calendar Keep track of your appointments and create meeting requests. Contacts Keep track of your friends and colleagues. Internet Explorer Mobile Browse Web and WAP sites as well as download new programs and files from the Internet.
Getting Started 47 Icon Description Adobe Reader LE View PDF (Portable Document Format) files on your device. Audio Booster Enhances your music experience by providing you with controls for adjusting equalizer, 3D sound, treble, and bass settings. Audio Manager Browse for music files by organizing music files into categories. Bluetooth Explorer Search for other Bluetooth devices that have file sharing enabled and access their Bluetooth shared folder.
Getting Started Icon Description Pictures & Videos View, organize, and sort pictures, animated GIFs, and video files on your device or a storage card. QuickGPS Downloads satellite data over the Internet via ActiveSync, Wi-Fi or GPRS to speed up the time for determining your current GPS position. SAPSettings Enables Bluetooth Remote SIM access on your phone. See Chapter 3 for more details. Search Search contacts, data, and other information on your device.
Getting Started 49 Icon Description Windows Live Use this mobile version of Windows Live™ to find information on the Web. It also lets you sign into your Windows Live account so that you can access your Live Mail messages and send/receive instant messages in Live Messenger. Windows Media Player Mobile Play back audio and video files. ZIP Save memory and free up storage space on your device by compressing files in the conventional ZIP format. 1.
Getting Started Icon Description Today Customize the appearance and the information to be displayed on the Today screen. Voice Speed Dial Create voice tags for voice dialing contacts and USIM/ SIM contacts as well as for launching programs. System tab Icon Description About This is where you can see basic information such as the Windows Mobile® version and type of processor used on your device. You can also specify a name for your device. Backlight Set the backlight timeout and adjust brightness.
Getting Started 51 Icon Description External GPS Set the appropriate GPS communication ports, if required. You may need to do this when there are programs on your device that access GPS data or you have connected a GPS receiver to your device. See Help for details. Key Lock Lock the buttons on your device except for the POWER button when the device is in Sleep mode. This ensures you will not switch the device on by accident and consume unnecessary power.
Getting Started Connections tab Icon Description Beam Set your device to receive incoming Bluetooth beams. Bluetooth Turn Bluetooth on, set your device to visible mode, and scan for other Bluetooth devices. Comm Manager Manage your device’s connections (including Wi-Fi, GPRS, and Bluetooth), turn the phone on or off, and enable or disable the Direct Push function. Connection Setup Configure your device’s data connections, such as GPRS, WAP, and MMS, based on the detected or selected network operator.
Chapter 2 Entering Text and Searching for Information 2.1 Entering Information 2.2 Using the On-screen Keyboard 2.3 Using the Touch Keyboard 2.4 Using the Touch Keypad 2.5 Using the Symbol Pad 2.6 Using Letter Recognizer 2.7 Using Block Recognizer 2.8 Using Transcriber 2.
Entering Text and Searching for Information 2.1 Entering Information When you start a program or select a field that requires text or numbers, the Input Panel icon becomes available on the menu bar. Tap the Input Selector arrow (that appears next to the Input Panel icon) to open a menu where you can select a text input method and customize input options. After selecting a text input method, the corresponding Input Panel is displayed, which you can use to enter text.
Entering Text and Searching for Information 55 2.2 Using the On-screen Keyboard When using Windows Mobile’s standard on-screen Keyboard, you can enter text by tapping keys on the keyboard that is displayed on the screen. To enter text using the on-screen Keyboard 1. In a program, tap the Input Selector arrow, and tap Keyboard. 2. Enter text by tapping keys on the on-screen Keyboard. To enlarge the on-screen Keyboard 1. Tap the Input Selector arrow, then tap Options. 2.
Entering Text and Searching for Information To enter text using the Touch Keyboard 1. Start a program that accepts text input, such as Word Mobile. 2. Tap the Input Selector arrow, and tap Touch Keyboard. 3. On the last row of the Touch Keyboard, tap the second key from the left to cycle through these input modes: XT9, Multitap or Numeric. See “XT9 mode”, “Multitap mode”, and “Numeric mode” to learn how to enter text with these modes. XT9 mode By default, the Touch Keyboard is set to XT9 mode.
Entering Text and Searching for Information 57 4. On the XT9 Settings screen, select or clear the following options according to your preferences: • Spell Correction. Lets you correct typographical errors by selecting from a list of possible words that reflect the characters of the keys you have tapped as well as characters of nearby keys. • Next Word Prediction. Predicts the next word in your text based on previous phrases you have constructed.
Entering Text and Searching for Information 2.4 Using the Touch Keypad The Touch Keypad is a 12-key on-screen keypad that has a similar layout as mobile phone keypads, plus some additional keys. Touch Keypad has large keys and enhanced input features such as XT9 predictive input, which makes it faster for you to enter text in your messages and documents. Tap to enter letters or symbols. • Tap to enter an uppercase letter. • Tap twice to turn on Caps Lock.
Entering Text and Searching for Information 59 2.5 Using the Symbol Pad Symbol Pad provides a comprehensive list of common symbols such as parentheses, braces, currency signs, and more, as well as punctuation marks and special characters. The Symbol pad is available when using both the Touch Keyboard and Touch Keypad. Tap a symbol to insert it into the message. Tap to close the Symbol Pad without selecting a symbol. Tap to display the previous page of symbols. Tap to display the next page of symbols.
Entering Text and Searching for Information 2.6 Using Letter Recognizer With Letter Recognizer, you can write individual letters, numbers, and punctuation marks, which are then converted into typed text. Note Letter Recognizer is available when text entry is possible. To use Letter Recognizer 1. From a program, tap the Input Selector arrow, and tap Letter Recognizer. 2. Write characters, numbers, and symbols in the designated writing area.
Entering Text and Searching for Information 61 2.8 Using Transcriber Transcriber is a handwriting recognition program that enables you to write in cursive, print, or a combination of both. To write using Transcriber 1. Start a program that accepts user input, such as Word Mobile. 2. Tap the Input Selector arrow, and tap Transcriber. The Transcriber introductory screen appears. Read the introduction and tap OK. 3. Position the cursor where you want text to appear. 4.
Entering Text and Searching for Information 2.9 Searching for Information You can search for files and other items stored in My Documents folder or on an installed storage card of your device. You can search by file name or by words located in the item. For example, you can search in e-mail messages, notes, appointments, contacts, and tasks, as well as in online Help. To search for a file or an item 1. Tap Start > Programs > Search. 2.
Chapter 3 Using Phone Features 3.1 Using the Phone 3.2 Making a Call 3.3 Receiving a Call 3.4 Making a Video Call 3.5 Receiving a Video Call 3.6 Smart Dialing 3.7 Additional Dialing Information 3.
Using Phone Features 3.1 Using the Phone Like a standard mobile phone, you can use your device to make, receive, and keep track of calls and send messages. You can also dial directly from Contacts, and easily copy phonebook entries from your SIM card to Contacts on your device. The Phone screen From the Phone screen, you can access Call History, Speed Dial, and Phone settings. To open the Phone screen, do either of the following: • Tap Start > Phone. • Press the TALK button.
Using Phone Features 65 To enable or disable Airplane Mode Another way to turn off the phone function is to switch your device to Airplane Mode. When you enable Airplane Mode, all wireless radios on your device are turned off, including the phone function, Bluetooth, and Wi-Fi. When you disable Airplane Mode, the phone function is turned back on and the previous states of Bluetooth and Wi-Fi are restored. 1. Tap Start > Programs > Comm Manager. 2.
Using Phone Features 3.2 Making a Call With your device, you can make a call from Phone, Contacts, TouchFLO, Speed Dial, Call History, and SIM Manager. Make a call from Phone 1. Tap Start > Phone. 2. On the Phone keypad, touch the keys with your finger or tap the keys using the stylus to enter the phone number. Tip If you tap a wrong number, tap Delete ( ) to erase each subsequent digit of a number. To erase the entire number, tap and hold Delete. 3.
Using Phone Features 67 To choose one of the numbers of a contact to dial By default, the mobile phone number (m) of a contact is dialed when you make a call from Contacts. However, you can specify that a different phone number is dialed instead. 1. Tap Start > Contacts. 2. Select the contact. 3. Press NAVIGATION left or right. The letters representing the number will change as you scroll through them.
Using Phone Features One-touch Speed Dial Use Speed Dial to call frequently-used numbers with a single tap. For example, if you assign a contact to the location 2 in Speed Dial, you can tap and hold the number 2 key on the Phone screen to dial the contact’s number. Before you can create a Speed Dial entry, the number must already exist in Contacts. To create a Speed Dial entry 1. On the Phone screen, tap Menu > Speed Dial.
Using Phone Features 69 Make a call from SIM Manager SIM Manager allows you to view the contents of your SIM card, transfer SIM phonebook entries to Contacts on your device, and make a call from your SIM card. To call a SIM contact 1. Tap Start > Programs > SIM Manager. Wait for your SIM card contents to load. 2. Tap and hold the name or phone number of the person you want to call, and tap Call. For more information about SIM Manager, see Chapter 6. 3.
Using Phone Features To put a call on hold Your device notifies you when you have another incoming call, and gives you the choice of rejecting or accepting the call. If you are already on a call and accept the new call, you can choose to switch between the two callers, or set up a conference call between all three parties. 1. Tap Answer to take the second call, and put the first one on hold. 2. To end the second call and return to the first call, tap End or press END on the device.
Using Phone Features 71 3.4 Making a Video Call Your device allows you to make video calls when you are within a 3G network coverage area. You need to use a 3G enable SIM card to make video calls. To make a video call Do any of the following: • On the Phone keypad, tap the phone number to call, then tap • On the Phone keypad, tap the phone number to call, then tap Menu > Video Call to start a video call. • From Contacts, tap and hold the desired contact, and tap Video Call.
Using Phone Features 1 Status area. Displays your service provider name, the other party's information, and call timer. 2 Image display area. Displays your image and the other party's image, depending on the selected Swap Image setting. 3 Camera On/Off. Tap to turn the camera on and off. When the camera is turned off, the image displayed depends on the Video Call options you have set. See “Set up video call options” for details. 4 Audio Mute/Unmute. Tap to mute/ unmute audio.
Using Phone Features 73 To adjust the brightness You can adjust the brightness of the display image. When you press NAVIGATION up or down or rotate the NAVIGATION WHEEL during a video call, a brightness bar appears at the bottom the screen. • Press NAVIGATION right or rotate the NAVIGATION WHEEL counterclockwise to increase brightness. • Press NAVIGATION left or rotate the NAVIGATION WHEEL clockwise to decrease brightness.
Using Phone Features General tab • Show still image. Select the image you want to display when you turn off the camera. • Preset (female). Displays a female picture in place of your image. • Preset (male). Displays a male picture in place of your image. • Custom image. Lets you use an image from file as your display picture. When this option is selected, the File Name box and the Browse button will be enabled, allowing you to select an image file. • Last video frame.
Using Phone Features 75 3.5 Receiving a Video Call To answer or reject an incoming video call • To answer the video call, tap Answer, or press TALK on your device. • To reject the video call, tap Ignore, or press END on your device. To end a video call Once an incoming or outgoing video call is in progress, press END on the device to hang up. 3.6 Smart Dialing Smart Dialing makes it easy for you to dial a phone number.
Using Phone Features If the matching list is long and you want to narrow down the search further, enter another letter. Using the same example above, if you continue to tap “3” which is associated with [d, e, f ], the matching list will be narrowed down to the following names: “Ben Miller”, “George Adams”, “Carter, Ellen”, “Dixon, Allan”. Make a call or send a text message using Smart Dialing 1. Press the TALK button on your device to open the Phone screen. 2.
Using Phone Features 77 3.7 Additional Dialing Information Make an emergency call Enter the international emergency number for your locale, and press the TALK button on your device. Tip Additional emergency numbers may be included in your SIM card. Contact your service provider for details. Make an international call 1. Tap and hold the number 0 key on the phone screen until the plus (+) sign appears. The plus (+) sign replaces the international prefix of the country that you are calling. 2.
Using Phone Features 3. On the BT Remote SIM Access screen, select the Remote SIM Access check box then tap Done. 4. Connect the car kit phone to your device via Bluetooth. To learn how to connect, consult your car kit phone’s manual. 5. If this is the first time you are pairing the car kit phone with your device, enter the car kit’s passcode on your device. 6. A pop-up message should appear on your device saying that a connection has been established between your device and car kit phone. Tap OK. 7.
Chapter 4 Setting Up Your Device 4.1 Basic Settings 4.2 Personalizing the Today Screen 4.
Setting Up Your Device 4.1 Basic Settings Time and date To set the time and date 1. Tap Start > Settings > System tab > Clock & Alarms > Time tab. 2. Select the correct time zone and change the date or time. Note During synchronization, the time on your device is updated with the time on your PC. To set the time and date for a different location If you visit or communicate with someone in a particular time zone often, you can select it as your visiting time zone. 1.
Setting Up Your Device 81 To set the backlight to dim after a time delay 1. Tap Start > Settings > System tab > Backlight. 2. Tap the Battery power or External power tab. 3. Select the Turn off backlight if device is not used for check box, and specify the time delay. To increase or decrease the size of text on the screen 1. Tap Start > Settings > System tab > Screen > Text Size tab. 2. Move the slider to increase or decrease the text size.
Setting Up Your Device Tips • You can use *.wav, *.mid, *.mp3, *.wma, or other types of sound files that you downloaded from the Internet or copied from your PC as ring tones. For a complete list of supported audio file formats for ring tones, see "Specifications" in the Appendix. • To use your sound files as ring tones, copy them first to the /My Documents/My Ringtones folder on your device, then select the sound from the Ring tone list of your device.
Setting Up Your Device 83 Phone services Your device can directly link to the mobile phone network, and enable you to access and change the settings of various phone services for your device. Phone services may include Call Forwarding, Call Waiting, Voicemail, and more. Contact your wireless service provider to find out about the availability of phone services for your device. To access and change settings of phone services 1. Tap Start > Settings > Personal tab > Phone > Services tab. 2.
Setting Up Your Device To display owner information Having owner information displayed on the Today screen makes it easier for someone to return your device to you if it is lost. 1. Tap Start > Settings > Personal tab > Owner Information. 2. On the Identification tab, enter your personal information. Tips • If you don’t see owner information on the Today screen, tap Start > Settings > Personal tab > Today. On the Items tab, select the Owner Info check box.
Setting Up Your Device 85 4. Do any of the following: • Under Display number of, select the type of tasks you want to appear on the Today screen. • In the Category list, select whether to display only tasks assigned to a specific category or to display all tasks. For more information about creating tasks on your device, see Chapter 6. Customize the Start menu You can choose which items appear in the Start menu. 1. Tap Start > Settings > Personal tab > Menus. 2.
Setting Up Your Device To set a device password 1. Tap Start > Settings > Personal tab > Lock. 2. Select the Prompt if device unused for check box, and in the box to the right, select how long your device must be idle before a password is required. 3. In the Password type box, select the type of password you would like to use. If your device is configured to connect to a network, use an alphanumeric password for increased security for your device. 4.
Chapter 5 Synchronizing Information With Your Computer 5.1 About Synchronization 5.2 Setting Up Windows Mobile® Device Center on Windows Vista® 5.3 Setting Up ActiveSync® on Windows XP® 5.4 Synchronizing With Your Computer 5.5 Synchronizing via Bluetooth 5.
Synchronizing Information With Your Computer 5.1 About Synchronization You can take information from your computer wherever you go by synchronizing them to your device.
Synchronizing Information With Your Computer 89 5.2 Setting Up Windows Mobile® Device Center on Windows Vista® Microsoft Windows Mobile® Device Center is the replacement for Microsoft® ActiveSync® on Windows Vista®. Note Some versions of Windows Vista come with Windows Mobile Device Center already installed. If Windows Mobile Device Center is not available on your Windows Vista, you can install it from the Getting Started Disc that came with your device.
Synchronizing Information With Your Computer Use Windows Mobile Device Center To open Windows Mobile Device Center, click Start > All Programs > Windows Mobile Device Center on your Windows Vista® computer. On Windows Mobile Device Center, you can do the following: • Click Mobile Device Settings to change synchronization settings.
Synchronizing Information With Your Computer 91 5.3 Setting Up ActiveSync® on Windows XP® The Getting Started Disc that comes with your device contains Microsoft ActiveSync 4.5 or later. Follow the steps in this section to install and set up ActiveSync on Windows XP or other compatible Windows systems. Note For a list of compatible Windows systems, please go to http://www.microsoft.com/windowsmobile/activesync/activesync45.mspx. Install ActiveSync 1.
Synchronizing Information With Your Computer 5.4 Synchronizing With Your Computer Connect and synchronize your device with your PC using the USB cable or Bluetooth connection. Start and stop synchronization You can manually synchronize either from your device or PC. From your device • Tap Start > Programs > ActiveSync, then tap Sync. To end synchronization before it completes, tap Stop. Tip To delete a partnership with one PC completely, disconnect your device from that PC first.
Synchronizing Information With Your Computer 93 3. To change synchronization settings for an information type, for instance, E-mail, select it and tap Settings. You can then set the download size limit, specify the time period of information to download, and more. Notes • Some information types such as Favorites, Files and Media cannot be selected in ActiveSync Options on your device. You can only select or clear these items from your PC’s Windows Mobile Device Center or ActiveSync.
Synchronizing Information With Your Computer 2. On your device, tap Start > Programs > ActiveSync. 3. Make sure that Bluetooth on both your device and the computer are turned on and set to visible mode. For more information, see “Bluetooth” in Chapter 10. If this is the first time you have connected to this computer via Bluetooth, you must first complete the Bluetooth wizard on your device and set up a Bluetooth partnership between your device and the computer.
Chapter 6 Organizing Contacts, Appointments, Tasks, and Other Information 6.1 Contacts 6.2 SIM Manager 6.3 Calendar 6.4 Tasks 6.5 Notes 6.
Organizing Contacts, Appointments, Tasks, and Other Information 6.1 Contacts Contacts is your address book and information storage for people and businesses you communicate with. You can create the following types of contacts on your device: • Outlook contacts. Contacts that are stored on your device, which can be created on your device or synchronized with your PC or the Exchange Server. • SIM contacts. Contacts that are stored on the SIM card.
Organizing Contacts, Appointments, Tasks, and Other Information 97 This photo appears on the Phone screen when you receive a call from the contact. 5. To assign a ring tone to the contact, tap the Ring tone field, scroll through the list of tones, then select a desired tone. 6. When finished, tap OK. Tips • If someone who is not in your list of contacts calls you, create a contact from Call History by tapping and holding a phone number and then tapping Save to Contacts from the shortcut menu.
Organizing Contacts, Appointments, Tasks, and Other Information 3. Touch the name of a contact to open his or her contact card. On the contact card, you will see the last outgoing or incoming call as well as detailed information such as phone numbers of the contact, e-mail address, and more. To find a contact on your device There are several ways to find a contact when your contact list is long. 1. Tap Start > Contacts. 2.
Organizing Contacts, Appointments, Tasks, and Other Information 99 To group similar contacts You can group similar contacts for easier management by assigning them to categories. 1. Create a new Outlook contact or edit an existing Outlook contact. 2. Tap Categories. 3. Select a preset category such as Business or Personal, or tap New to create your own category. 4. When finished, tap OK. To view contacts by category • Tap Menu > Filter then select the desired category.
Organizing Contacts, Appointments, Tasks, and Other Information 1. Tap Start > Contacts, then select a contact. 2. Tap Menu > Send as vCard. 3. A new MMS message is created with the vCard file attached. Enter the mobile phone number or e-mail address of the recipient then tap Send. For more information, see “MMS” in Chapter 7. 6.2 SIM Manager SIM Manager allows you to view the contents of your SIM card, transfer contacts from your SIM card to your device or vice versa, and make a call to a SIM contact.
Organizing Contacts, Appointments, Tasks, and Other Information 101 By default, /M, /W and /H are appended to indicate mobile, work and home phone numbers respectively. You can edit this indicator first before you start copying contacts to your SIM card. Indicators of the other types of phone numbers are left empty for you to define them. 1. Tap Start > Programs > SIM Manager, then tap Menu > Tools > Options. 2. Select the check boxes of the types of phone numbers that you want to be added to the SIM card.
Organizing Contacts, Appointments, Tasks, and Other Information 6.3 Calendar Use Calendar to create appointments, including meetings and other events. You can also synchronize Calendar appointments between your device and PC. Create appointments To schedule an appointment 1. Tap Start > Calendar. 2. Tap Menu > New Appointment. 3. Enter a name for the appointment. 4. Do one of the following: • If it is a special occasion such as a birthday or a whole-day event, set the All Day option to Yes.
Organizing Contacts, Appointments, Tasks, and Other Information 103 4. Set the time when you want the reminder to alert you. 5. Tap OK to return to the calendar. View appointments By default, Calendar displays appointments in Agenda view. You can also look at your appointments in Day, Week, Month, and Year views. The highlighted hours here indicate the time of your appointments. Indicates that there is a conflict with another appointment. Tap to view appointment details. Tap to switch views.
Organizing Contacts, Appointments, Tasks, and Other Information Send appointments To send a meeting request Use Calendar to schedule meetings via e-mail with contacts who use Outlook or Outlook Mobile. 1. Tap Start > Calendar. 2. Schedule a new appointment, or open an existing one and tap Menu > Edit. 3. Tap Attendees, then tap Add Required Attendee or Add Optional Attendee and add the contacts whom you want to invite.
Organizing Contacts, Appointments, Tasks, and Other Information 105 6.4 Tasks Use Tasks to keep track of things you need to do. A task can occur once or repeatedly (recurring). You can set reminders for your tasks and you can organize them using categories. Your tasks are displayed in a task list. Overdue tasks are displayed in red. To create a task 1. Tap Start > Programs > Tasks. 2.
Organizing Contacts, Appointments, Tasks, and Other Information To set the default reminder for all new tasks 1. Tap Start > Programs > Tasks. 2. Tap Menu > Options. 3. Select the Set reminders for new items check box. 4. Tap OK to return to the task list. Note The new tasks must have due dates set in order for the reminder to take effect. To show start and due dates in the task list 1. Tap Start > Programs > Tasks. 2. Tap Menu > Options. 3. Select the Show start and due dates check box. 4. Tap OK.
Organizing Contacts, Appointments, Tasks, and Other Information 107 6.5 Notes Using Notes, you can create handwritten and typed notes, record voice notes, convert handwritten notes to text for easy readability, and more. To create a note 1. Tap Start > Programs > Notes. In the note list, tap New. 2. Tap the Input Selector arrow next to the Input Method icon on the menu bar, tap the input method you want, and enter your text. 3. If the Input Selector arrow is not displayed, tap the Input Method icon. 4.
Organizing Contacts, Appointments, Tasks, and Other Information To record a voice note You can create a stand-alone recording (voice note) or you can add a recording to a note. 1. Tap Start > Programs > Notes. 2. If you do not see the Recording toolbar, tap Menu > View Recording Toolbar. 3. Do one of the following: • To create a stand-alone recording, record from the note list. • To add a recording to a note, create or open a note. 4. Tap the Record icon ( ) to begin recording your voice.
Organizing Contacts, Appointments, Tasks, and Other Information 109 6.6 Voice Recorder Voice Recorder lets you record your voice and then quickly send it in an MMS or e-mail, beam it, or set the recorded voice as your ring tone. Note Voice Recorder saves voice recordings in AMR-NB (Adaptive Multi-Rate Narrowband) format only. This is a common speech audio format used in mobile devices. To record your voice 1. Tap Start > Programs > Voice Recorder. 2. Hold the device’s microphone close to your mouth. 3.
Organizing Contacts, Appointments, Tasks, and Other Information To beam the voice recording 1. Select the voice recording(s) you want to beam then tap Menu > Beam File. Tip To select multiple recordings, tap and drag over the desired recordings or tap Menu > Select All. 2. Tap the device you want to send the voice recording(s) to. 3. On the other device, accept the file transfer to receive the file.
Chapter 7 Exchanging Messages 7.1 Messaging 7.2 Text Messages 7.3 MMS 7.4 Types of E-mail Accounts 7.5 E-mail Setup Wizard 7.
Exchanging Messages 7.1 Messaging Messaging is where your text messages (SMS), multimedia messages (MMS), and e-mails are located. When you receive new messages, you can open them from the Today screen by tapping the type of message that you want to open. New e-mail messages New SMS and MMS messages To select a messaging account Do one of the following: • Tap Start > Messaging. The Account Picker screen then appears where you can select an account.
Exchanging Messages 113 To automatically add a signature in outgoing messages You can automatically add your name and other information as your signature in outgoing SMS, MMS and e-mail messages by following these steps: Tip You need to specify your signature for each type of messaging account. 1. Tap Start > Messaging, then tap Menu > Options. 2. Tap Signatures. 3. Select a type of messaging account in which to add a signature. 4. Select the Use signature with this account check box. 5.
Exchanging Messages 5. A new text message is then created. To add more recipients, enter their mobile phone numbers in the To field, separating them with a semicolon. You can also tap To if you want to add mobile phone numbers from Contacts. 6. Enter your message. • To quickly add common messages, tap Menu > My Text and tap a desired message. • To check the spelling, tap Menu > Spell Check. 7. Tap Send. Tips • To enter symbols, tap 123 on the on-screen keyboard and then tap a symbol.
Exchanging Messages 115 7.3 MMS Sending multimedia messages (MMS) to your friends and family is fun and easy. You can include pictures, videos, and audio clips in a multimedia message. Notes • Multimedia messaging is a charged service and has to be provisioned on your mobile account. Please contact your wireless service provider to have MMS provisioned as part of your calling plan. • Make sure the size of MMS messages that you send is within the limits allowed by your wireless service provider.
Exchanging Messages • Server address. URL address of the server where MMS messages are stored. • Connect via. Select the connection that your device uses for MMS messages. • Send limit. Select the maximum MMS message size allowed by your wireless service provider. • WAP version. Select either WAP 1.2 or WAP 2.0, depending on which one is being used by your wireless service provider. 5. Tap Done.
Exchanging Messages 117 5. Tap the Insert icon ( )to select and insert a photo or video clip. When selecting a photo or video clip, you can: • Tap Select to insert the selected photo or video clip into the MMS message you are composing. • Tap to take a photo and insert it into the MMS message. • Tap to record MMS video and insert it into the MMS message. • Tap Exit ( ) to quit selection and return to the MMS message. 6. Enter text and insert audio clips by tapping the respective areas.
Exchanging Messages To add an audio clip to an MMS message You can add one audio clip per slide in your MMS message. 1. Tap Insert audio on your MMS message. By default, My Documents will be shown. Tap My Music or another folder that contains audio files. When navigating folders, tap the Down arrow ( ) to return to the upper folder. 2. Select an audio file. When selected, you can: • Tap • Tap Select to insert it into your MMS message.
Exchanging Messages 119 To block a phone number from sending you MMS messages If you do not want to receive MMS messages from a particular sender, you can add the sender’s phone number to the MMS Blacklist. 1. When you receive a new MMS message, open and view the message. 2. To avoid receiving MMS messages from this sender next time, tap Menu > Show > Message Detail. 3. On the MMS Detail screen, tap Menu > Show Contact Details. 4. Tap Menu > Save to Blacklist. 5. Tap Done.
Exchanging Messages 7.5 E-mail Setup Wizard Windows Mobile’s E-mail Setup Wizard lets you easily set up your personal and work e-mail accounts. You can add an e-mail account from an Internet Service Provider (ISP) or other e-mail provider as well as web-based accounts such as Gmail®, Yahoo!® Mail Plus, AOL®, etc. Note For more information about setting up your company Outlook e-mail account, see Chapter 8.
Exchanging Messages 121 Note If Auto Setup is unsuccessful, select Internet e-mail from the Your e-mail provider list on the next screen. You will also be asked to enter e-mail server settings during the setup process. See “To specify e-mail server settings” for details. 4. Enter your name. You can also edit the Account display name field to specify the name of your ISP or e-mail provider. Tap Next. 5. Enter your login name if it does not show automatically in the User name field.
Exchanging Messages To customize download and format settings Before you tap Finish when setting up your POP3 or IMAP4 e-mail account, you can tap Review all download settings to choose download options, message format, and other settings.
Exchanging Messages 123 7.6 Using E-mail After setting up e-mail accounts on your device, you can start sending and receiving e-mail messages. Create and send messages To compose and send a message 1. Tap Start > Contacts. 2. Slide your finger upward on the touch screen to scroll down the contact list. See “Finger scrolling and finger panning” in Chapter 1 for more details on finger scrolling. 3. Touch the contact’s name to open his or her contact card. 4.
Exchanging Messages Filter the Inbox message list When the Inbox on your device is full of messages, it may be difficult to browse and locate a desired message. You can filter your Inbox to display only the messages that contain a particular sender or subject you are searching for. To filter your Inbox • Enter the sender name or e-mail subject you want to look for using the on-screen keyboard. As you tap keys, the message list narrows down to the conditions you have set.
Exchanging Messages 125 To download an attachment An attachment appears below the subject of the message. Tapping the attachment opens the attachment if it has been fully downloaded or marks it for download the next time you send and receive e-mail. Notes • If there are multiple attachments in the message, all attachments are downloaded. • For information about setting your device to automatically download file attachments, see "Customize e-mail settings".
Exchanging Messages 5. If the e-mail does not download immediately, tap Menu > Send/ Receive. 6. If images do not immediately appear on the message, tap Internet pictures blocked then tap Download Internet pictures. 7. Tap Menu and choose whether to reply or forward the message. 8. Enter your response then tap Send. Tip E-mail can contain hyperlinks to web pages. Download messages The manner in which you download messages depends on the type of e-mail account you have.
Exchanging Messages 127 Customize e-mail settings To change the download size and format for Outlook e-mail 1. Disconnect your device from the computer. 2. Tap Start > Programs > ActiveSync. 3. Tap Menu > Options, select E-mail, then tap Settings. 4. On the E-mail Sync Options screen: • Under Message format, select HTML or Plain text. • Under Download size limit, select the desired e-mail size. 5. Close ActiveSync and reconnect your device to the computer.
Exchanging Messages 5. Select a download size from the Download attachments smaller than list box. 6. Tap Finish. To store attachments on a storage card 1. Tap Start > Messaging. 2. Tap Menu > Options > Storage tab. 3. Select the When available, use this storage card to store attachments checkbox.
Chapter 8 Working With Company E-mails and Meeting Appointments 8.1 Synchronizing with the Exchange Server 8.2 Working With Company E-mails 8.3 Managing Meeting Requests 8.
Working With Company E-mails and Meeting Appointments 8.1 Synchronizing with the Exchange Server To keep up-to-date with your company e-mails and meeting schedules while you’re out of the office, you can connect your device to the Internet wirelessly and synchronize with your company’s Exchange Server. Set up an Exchange Server connection Before you can synchronize or access information on the Exchange Server, you need to set up an Exchange Server connection on your device.
Working With Company E-mails and Meeting Appointments 131 Tip To change Exchange Server settings, open ActiveSync then tap Menu > Configure Server. Start synchronization Before you start synchronizing with the Exchange Server, make sure your device has been set up with a data connection to the Internet so that you can synchronize wirelessly. For more information about connections, see Chapter 10. After you finish setting up an Exchange Server connection, your device automatically starts synchronization.
Working With Company E-mails and Meeting Appointments You need to perform a full synchronization between your device and the Exchange Server first before Direct Push can be enabled. Requirement The Direct Push feature works for your device only if your company is using Microsoft Exchange Server 2003 Service Pack 2 (SP2) with Exchange ActiveSync or higher version. To enable Direct Push via Comm Manager 1. Tap Start > Programs > Comm Manager. 2.
Working With Company E-mails and Meeting Appointments 133 Instant download through Fetch Mail The Fetch Mail feature downloads an entire e-mail immediately without the need for you to perform a full Send/Receive action. This limits the download to just the e-mail message that you want and helps save data cost. Requirement Fetch Mail works for your device only if your company is using Microsoft Exchange Server 2007 or higher. 1. Tap Start > Messaging > Outlook E-mail. 2. Tap an e-mail message to open it.
Working With Company E-mails and Meeting Appointments 5. From the Look in list, choose whether to search from your inbox or outbox only or to search all folders. 6. Tap Search. Flag your messages Flags serve as a reminder for you to follow-up on important issues or requests contained in e-mail messages. Flagging messages, which has been a useful feature on desktop Outlook E-mail, can also be done in Outlook Mobile on your device. You can flag received e-mail messages on your device.
Working With Company E-mails and Meeting Appointments 135 Out-of-office auto-reply Outlook Mobile allows you to retrieve and change your out-of-office status. Just like desktop Outlook E-mail, Outlook Mobile automatically sends an auto-reply message when you’re not available. To send out-of-office auto-reply messages 1. Tap Start > Messaging > Outlook E-mail. 2. Tap Menu > Tools > Out of Office. 3. From the I am currently list, select Out of the Office. 4. Enter your auto-reply message then tap Done. 8.
Working With Company E-mails and Meeting Appointments 3. Choose whether or not to edit your response e-mail before sending then tap OK: 4. If you accepted the meeting request, it will automatically be added as an appointment in Calendar on your device. To view the list of meeting participants 1. Tap Start > Calendar. 2. Tap a meeting request that you previously sent, then tap Attendees. The list of required and optional attendees will be listed.
Working With Company E-mails and Meeting Appointments 137 8.4 Finding Contacts in the Company Directory In addition to having contacts on your device, you can access contact information from your organization’s Company Directory. By having over-the-air access to the Company Directory, you can easily send e-mail messages and meeting requests to anyone in your company.
Working With Company E-mails and Meeting Appointments 3. Enter a partial or full contact name and tap Search. In the search results list, tap a contact to select it. Notes • You can save a contact from the Company Directory to your device by selecting the contact then tapping Menu > Save to Contacts. • You can search on the following information as long as that information is included in the Company Directory: First name, Last name, E-mail name, Display name, E-mail address, or Office location.
Chapter 9 Working With Documents and Files 9.1 Microsoft® Office Mobile 9.2 Adobe® Reader® LE 9.3 Copying and Managing Files 9.4 ZIP 9.
Working With Documents and Files 9.1 Microsoft® Office Mobile Microsoft® Office Mobile consists of the following applications: • Microsoft® Office Word Mobile lets you create and edit documents and templates in Word Mobile and save them as *.doc, *.rtf, *.txt, and *.dot files. • Microsoft® Office Excel® Mobile lets you create and edit Excel workbooks and templates on your device. • Microsoft® Office PowerPoint® Mobile allows you to view (not create) slide show presentations in *.ppt and *.
Working With Documents and Files 141 9.2 Adobe® Reader® LE Adobe® Reader® LE is an application for viewing PDF (Portable Document Format) documents on your device. It supports a subset of the features found in the PC versions of Adobe Reader. To open Adobe Reader LE • Tap Start > Programs > Adobe Reader LE. To open a PDF file on your device Do one of the following: • • Open a PDF file in Adobe Reader LE. Open File Explorer and find the desired PDF file, then tap the file to open it.
Working With Documents and Files 9.3 Copying and Managing Files You can copy files between your device and PC, or copy files to a storage card that is inserted on your device. You can also efficiently manage your files and folders using File Explorer. To copy files using Windows Mobile Device Center or ActiveSync 1. Connect your device to the PC. 2. Click File Management > Browse the contents of your device in Windows Mobile Device Center or click Explore in ActiveSync on your PC.
Working With Documents and Files 143 To copy files to a storage card 1. Make sure the storage card is properly inserted into your device. 2. Tap Start > Programs > File Explorer and navigate to the appropriate folder. 3. Tap and hold the file you want to copy, and tap Copy. 4. Tap the Down arrow ( ) then tap Storage Card from the list. 5. Tap Menu > Edit > Paste. Tip You can configure programs such as Word Mobile and Excel Mobile to directly save edited files on your storage card.
Working With Documents and Files 3. Tap Menu > Action > Extract. 4. Choose a folder in which files will be extracted to, then tap Extract. To create a zip archive 1. Tap File > New Archive. 2. On the Save As screen, enter a zip file name and choose a folder in which to save the zip file. You can also choose whether the zip file will be saved on the device’s main memory or storage card. 3. Tap Save. 4. Tap Menu > Action > Add. 5. Double-tap the folder that contains the files you want to archive. 6.
Working With Documents and Files 145 To open Sprite Backup • On your device, tap Start > Programs > Sprite Backup. Sprite Backup operates in two different modes: Basic mode and Advanced mode. Basic mode Advanced mode To back up data in Basic mode Basic mode is the default mode, and allows you to easily back up your entire device with the tap of a button. Note To change backup options or location, you will need to do it in Advanced mode. 1. On the Basic mode screen, tap Backup Now. 2.
Working With Documents and Files To back up data in Advanced mode Advanced mode is designed for users with more advanced backup requirements. 1. Tap Options > Switch to Advanced Mode. 2. In the Backup tab, you will see a tree view of the data and files on your device. Tap the ‘+’ symbol at the left of an item to view its subitems. Use the check boxes to select or exclude items for backup. 3. Tap the Backup button and follow the on-screen instructions to complete the backup.
Chapter 10 Getting Connected 10.1 Comm Manager 10.2 Connection Setup 10.3 Ways of Connecting to the Internet 10.4 Wi-Fi 10.5 GPRS/3G 10.6 Dial-up 10.7 Starting a Data Connection 10.8 Internet Explorer® Mobile 10.9 Windows Live™ 10.10 Using Your Device as a Modem (Internet Sharing) 10.
Getting Connected 10.1 Comm Manager Comm Manager acts like a central switch that lets you enable or disable phone features as well as manage your data connections easily. To open Comm Manager • Tap Start > Settings > Connections tab > Comm Manager. • Tap Start > Programs > Comm Manager. 1 2 Off/disabled On/enabled 3 4 5 Unavailable 6 1 Tap to switch Airplane mode on or off. Turning on Airplane mode turns off the phone, Bluetooth and Wi-Fi functions.
Getting Connected 149 10.2 Connection Setup Connection Setup configures your device’s data connections, such as GPRS, WAP, and MMS, for you so that you do not need to enter the settings manually onto your device. All you need to do is to select your network operator, then Connection Setup does all the configuration for you.
Getting Connected 4. Tap Yes. Connection Setup configures the data connection settings. 5. After the Connection Setup completes the configuration, tap Restart. 10.3 Ways of Connecting to the Internet Your device’s networking capabilities allow you to access the Internet or your corporate network at work through wireless and conventional connections.
Getting Connected 151 Connect to wireless networks After Wi-Fi is turned on in Comm Manager, your device scans for available wireless networks in your area. To connect to a wireless network 1. The network names of the detected wireless networks are displayed on a pop-up message window. Tap the desired wireless network, then tap OK. 2. On the next pop-up message window, do one of the following: • Tap The Internet if the wireless network connects your device to the Internet.
Getting Connected • Title bar. When you enable Wi-Fi on your device, the Wi-Fi ON icon appears on the title bar. After Wi-Fi is turned on, your device scans for available wireless networks and the wireless signal icon appears on the title bar. The arrows in this icon move back and forth while your device is scanning for a wireless network signal. Once your device successfully connects to a wireless network, the arrows stop moving. • Wi-Fi Status screen.
Getting Connected 153 To save battery power while connected to a wireless network Using Wi-Fi quickly consumes battery power. Turn off Wi-Fi when not in use. You can also enable power saving settings. 1. Tap Start > Settings > Connections tab > Wireless LAN. 2. On the Power Mode tab, move the Power Save Mode slider to a position that optimizes performance with the least power consumption.
Getting Connected 4. In the Select a modem list, select Cellular Line (GPRS, 3G), then tap Next. 5. Enter the Access point name, then tap Next. 6. Enter the user name and password, only if required. 7. Tap Finish. Notes • To view help information for any screen, tap the help icon ( ). • To modify your connection settings, tap Manage existing connections on the Connections screen, and complete the connection wizard. 10.
Getting Connected 155 6. Enter your user name, password, and any other information required by your ISP. 7. Tap Finish. 10.7 Starting a Data Connection After setting up a data connection such as GPRS or ISP dial-up on your device, you can now connect your device to the Internet. The connection is started automatically when you begin using a program that accesses the Internet such as Internet Explorer® Mobile.
Getting Connected To view a Web page using finger scrolling and panning • Slide your finger upward to scroll down the Web page, or slide your finger downward to scroll up the Web page. • To pan downward, touch and hold on the touch screen then drag your finger upward. To pan upward, touch and hold on the touch screen then drag your finger downward. • To pan towards the right, touch and hold on the touch screen then drag your finger to the left.
Getting Connected 157 Tap Menu > Tools and choose to send the current Web page link, view the page’s properties, or set preferences. Note: To save an image from a Web page to your device, tap and hold the image then tap Save Image. For more information about using Internet Explorer® Mobile, please go to: http://www.microsoft.com/windowsmobile/help/pocketpc/browseinternet.mspx 10.9 Windows Live™ Windows Live™ gives you a full Internet experience on your device.
Getting Connected Set up Windows Live™ The first time you use Windows Live™, sign in by using your Windows Live ID, which is your Windows Live Mail or Hotmail address, and password. To set up Windows Live for the first time 1. Tap Start > Programs > Windows Live. 2. Tap Sign in to Windows Live. 3. On the next screen, tap the links to read the Windows Live™ Term of Use and the Microsoft Privacy Statement. After reviewing them, tap Accept. 4.
Getting Connected 159 The Windows Live™ interface On the main interface of Windows Live™, you will see a search bar, navigation bar, and an area where you can customize to show your picture. 1 1 Live Search Bar 2 Tap the Left or Right arrow to switch between Windows Live Messenger, Live Mail, and Sync status. 3 Tap to change the display name, picture, or personal message. 4 Tap Menu to access and change settings.
Getting Connected Windows Live Messenger With this mobile version of Windows Live Messenger, you enjoy many of the same cool features that you get from the desktop version, which include the following: • • • • • • • • Note Instant messaging via text and voice Multiple conversations Add emoticons Contact list with presence Send and receive files including photos Change status/display name View contacts by online status, groups, and more Send messages even when a contact is offline Before you can use W
Getting Connected 161 To start and end conversations 1. In the contact list, select a contact then tap Send IM to open a message screen. 2. Enter your text message in the text entry area of the message screen. 3. To add an emoticon, tap Menu > Add emoticon then tap an icon from the list of emoticons. 4. Tap Send. 5. To end a conversation with the current contact, tap Menu > End conversation. Tips • To send a file, tap Menu > Send. You can choose to send a picture, voice clip or any file.
Getting Connected 10.10 Using Your Device as a Modem (Internet Sharing) Internet Sharing connects your PC or notebook computer to the Internet by using your device’s data connection (GPRS or EDGE, for instance). You can choose to connect via USB or Bluetooth. Notes • Make sure your device has a SIM card installed, and your device has a GPRS or phone dial-up modem connection. If your device has not been set up with a data connection yet, tap Menu > Connection Settings on the Internet Sharing screen.
Getting Connected 163 To use your device as a Bluetooth modem For the computer to use the Internet connection of your device, activate Internet Sharing on your device, then set up a Bluetooth Personal Area Network (PAN) between the computer and your device. 1. On your device, turn on Bluetooth and set it to visible mode by following the steps in “To turn Bluetooth on and make your device visible”. 2.
Getting Connected Note If the Bluetooth adapter or dongle on your computer was installed using a third-party provided driver, open the Bluetooth software that came with the Bluetooth adapter/dongle to connect your computer and device via Bluetooth. Refer to the Bluetooth adapter/dongle documentation for more information. 8.
Getting Connected 165 To turn Bluetooth on and make your device visible 1. On your device, tap Start > Settings > Connections tab > Bluetooth > Mode tab. 2. Select the Turn on Bluetooth and Make this device visible to other devices check boxes. 3. Tap OK. Bluetooth partnerships A Bluetooth partnership is a relationship that you create between your device and another Bluetooth-enabled device in order to exchange information in a secure manner. To create a Bluetooth partnership 1.
Getting Connected To accept a Bluetooth partnership 1. Ensure that Bluetooth is turned on and in visible mode. 2. Tap Yes when prompted to establish a partnership with the other device. 3. Enter a passcode (the same passcode that is entered on the device requesting the partnership) to establish a secure connection. The passcode must be between 1 and 16 characters. 4. Tap Next. 5. Tap Finish. You can now exchange information with the paired device.
Getting Connected 167 4. Tap the name of the Bluetooth headset, then tap Next. 5. Enter the passcode of the Bluetooth headset, then tap Next. 6. Make sure the Hands Free check box is selected. If you have a Bluetooth stereo headset, also make sure Wireless Stereo is selected. 7. Tap Finish. While the Bluetooth stereo headset is connected, the Headset icon ( ) will appear on the title bar. Note If the Bluetooth stereo headset becomes disconnected, turn the headset on and repeat steps 1 to 3 above.
Getting Connected If your computer has Windows Vista® or Windows XP SP2 and your computer’s Bluetooth adapter is supported by your Windows version, do the following steps: a. On your computer, open Bluetooth Devices from the Control Panel then click the Options tab on the Bluetooth Devices window. b. For Windows Vista, select Allow Bluetooth devices to find this computer. For Windows XP, select Turn discovery on and Allow Bluetooth devices to connect to this computer. c.
Getting Connected 169 • For your device to receive Bluetooth beams, tap Start > Settings > Connections tab > Beam and make sure the Receive all incoming beams check box is selected. Bluetooth Explorer and Bluetooth file sharing Bluetooth Explorer searches for other Bluetooth devices that have file sharing enabled and lets you access their Bluetooth shared folder. You can copy files from and to their shared folder, and create subfolders in it.
Getting Connected 3. Select one or more files, then tap Menu > Edit and choose to cut or copy the files. 4. Tap Up twice. 5. Navigate to the folder where you want to paste the files on your device, then tap Menu > Edit > Paste. Print files via Bluetooth Connect your device to a Bluetooth printer to print contact information, appointment details, messages, and other file types. Note You can print files in the .txt, .jpg, .xhtml, .vcf, .vcs file formats.
Getting Connected 171 To print a JPEG file 1. Do one of the following: • In Pictures & Videos, select the JPEG file and then tap Menu > Print via Bluetooth. • In File Explorer, tap and hold the JPEG file and then on the menu, tap Print via Bluetooth. 2.
Getting Connected
Chapter 11 Using GPS 11.1 Guidelines and Preparation for Using GPS 11.2 Downloading Satellite Data via QuickGPS 11.3 Using TomTom NAVIGATOR 11.
Using GPS 11.1 Guidelines and Preparation for Using GPS • Do not operate the GPS system while driving. The plotted GPS route is only for driving reference. It should not interfere with actual driving behavior. • Please use the GPS system cautiously. Users shall be liable for any damages resulting from negligent operation of the system. • The GPS signal cannot pass through solid non-transparent objects.
Using GPS 175 • When using the device inside a vehicle, use the car holder to mount the device securely in place. Avoid placing the device in the areas shown in the following diagram: 1 Do not place where it will block the driver’s vision. 2 Do not place where air bags could deploy. 3 Do not place anywhere in the vehicle without securing the device in the holder.
Using GPS 11.2 Downloading Satellite Data via QuickGPS Before you start to use your device for GPS navigation, open the QuickGPS program first to download ephemeris data (current satellite position and timing information) onto your device. This data is needed to determine the GPS position of your current location. QuickGPS downloads ephemeris data from a Web server, instead of from the satellites, using the Internet connection on your device, which can be via ActiveSync or 3G/GPRS.
Using GPS 177 Download options To configure download times, tap Menu > Options and choose from the available options: • Remind me when data expires. Enables your device to display a reminder message when the validity of the ephemeris data has expired. When you see the reminder message, tap Menu to dismiss the reminder or to set the snooze time so that you will be reminded again. Tap OK to open the QuickGPS program and download the latest data. • • Autodownload when data expires.
Using GPS 11.3 Using TomTom NAVIGATOR TomTom NAVIGATOR is a GPS navigation software that provides clear routing directions and vocal instructions to guide you in your journey, based on the destination address you specified, a contact you selected, a point of interest, etc. TomTom NAVIGATOR gives you several routes to select from when you plan your journey in advance. Places that you frequently go to can be added as favorites.
Using GPS 179 If it takes longer than 5 minutes, make sure that you are in an open place without tall buildings or trees around you. In the future, your position will be found much faster, normally within a few seconds. Tip For your GPS receiver to determine your current position faster, use QuickGPS first to download the latest ephemeris data to your device. For more information about QuickGPS, see “Downloading Satellite Data via QuickGPS“ earlier in this chapter.
Using GPS Main Menu Tap anywhere on the map in the Driving View screen to open the Main Menu. The Main Menu has three screens of icons. Tap the Next icon ( ) to switch between the menu screens. • Navigate to. Lets you select a destination. • Find alternative. Calculates an alternative route if you want to avoid traffic or other nuisances. • TomTom Traffic. Enables and disables reception of traffic information. (This is a subscription service). • Add Favorite.
Using GPS 181 Select a destination When you tap Navigate to on the Main Menu, you are given several options to set your destination. Tap the Next icon ( ) to browse through the various types of destinations. Some of the common destinations you may want to go to include the following: • Home. Your Home location. You need to specify your Home location first under Preferences. • Favorite. A frequently visited place that you assign as a favorite. For more information, see “Favorites”. • Address.
Using GPS After you have set your destination, NAVIGATOR asks you whether you need to arrive at a particular time. After you tap YES and enter an arrival time, NAVIGATOR shows you whether you will arrive on time or not. NAVIGATOR then calculates the route and displays the Route Summary: Tap Done. NAVIGATOR then displays again the Driving View screen, and starts guiding you to your destination with spoken instructions and visual instructions.
Using GPS 183 To navigate to a favorite 1. Tap the Driving View screen to open the Main Menu. 2. Tap Navigate to, then tap Favorite. 3. Select a favorite from the list. NAVIGATOR then calculates the route for you. 4. After the route is calculated, tap Done. NAVIGATOR will immediately start guiding you to your destination with spoken instructions and visual instructions on the screen. To rename or delete a favorite 1. Tap the Driving View screen to open the Main Menu. 2. Tap Change preferences. 3.
Using GPS POI locations POI categories To add a point of interest 1. Tap the Driving View screen to open the Main Menu. 2. Tap Change preferences > Manage POIs. Before you can add a POI, you have to create a category first. You can only add your POIs to a POI category you have created yourself. 3. To add a category, tap Add POI category. 4. Enter a name for your POI category, for example, ‘Favorite restaurants’, then select a marker for your POI category.
Using GPS 185 Advanced planning It is recommended to plan in advance before you start on the journey. You can use the Advanced planning function to find out which is the fastest or shortest route between your starting point and destination. To plan a route in advance 1. Tap the Driving View screen to open the Main Menu. 2. Tap the Next icon ( ), then tap Advanced planning. 3. Select the starting point for your journey in the same way as you would normally select your destination. 4.
Using GPS 1 3 2 4 1 This Scale Bar shows the distance range shown on the map based on the current zoom scale. 2 This is your current position on the map. Tap another location to move to a different part of the map. 3 Tap to centre the map on your current position. 4 This is the Zoom Bar. Change the scale of the map by moving the Zoom Bar up or down. 5 6 7 5 Tap to choose what items to show on the map, such as points of interest, favorites, street names, and more.
Using GPS 187 Setting Enable/ disable POIs Turn off sound Volume preferences Manage Favorites Change Home location Manage maps Manage POIs Planning preferences Toll road preferences Compass preferences Change map colors Show GPS status Keyboard preferences Name preferences Status bar preferences Set units Operate lefthanded Description Allows you to choose which categories of points of interest to display on the map. Turns the spoken instructions off. To turn the voice back on, tap Turn on sound.
Using GPS Setting Description Hide tips Tap to prevent TomTom Navigator from displaying tips. Change voice Allows you to choose another voice for the spoken instructions. (Available only when you’ve installed several voices into NAVIGATOR). Change Lets you select the language used for the TomTom NAVIGATOR language interface. Reset factory Tap to reset TomTom NAVIGATOR settings to the factory defaults. All settings settings, including Favorites, Home location, etc, will be deleted.
Chapter 12 Experiencing Multimedia 12.1 Camera 12.2 Camera Album 12.3 Pictures & Videos 12.4 Windows Media® Player Mobile 12.5 Streaming Media 12.6 Audio Manager 12.7 Using Audio Booster 12.
Experiencing Multimedia 12.1 Camera Taking photos and recording video clips along with audio are easy with your device’s two built-in cameras: Main camera: Rear 2 megapixel CMOS camera for capturing high resolution pictures and video clips with audio 2nd camera: Front camera for video calls and taking self-portrait shots To open the Camera screen • Press the CAMERA button on your device. • Tap Start > Programs > Camera.
Experiencing Multimedia 191 You can select from the following capture modes: Icon Capture Mode Photo: Captures standard still images. Video: Captures video clips, with or without accompanying audio. MMS Video: Captures video clips suitable for sending with MMS messages. Contacts Picture: Captures a still image and gives you the option to immediately assign it as a Photo ID for a contact. Picture Theme: Captures still images and places them within frames.
Experiencing Multimedia Camera controls • Press CAMERA or ENTER to take a photo or contacts picture. • Press CAMERA or ENTER to start recording video; press it again to stop recording. • Press CAMERA or ENTER each time when taking photos for a picture theme or panorama. • To take consecutive shots in Sports mode, press CAMERA or ENTER, then move your device to follow the movement of your subject.
Experiencing Multimedia 193 In Video and MMS Video modes, this shows the remaining duration that can be recorded. While recording video, this shows the recorded duration. 3 Zoom control. Tapping zoom out. / on the screen allows you to zoom in or Note This control only appears when zooming is supported by the Resolution you have selected. Tip You can also press NAVIGATION up/down or rotate the NAVIGATION WHEEL to zoom in an out. 4 Album. Tap to open Camera Album. See “Camera Album” for details.
Experiencing Multimedia Quick Settings Panel The Quick Settings Panel provides a quick way of adjusting the most common camera settings. Tap the screen to open the Quick Settings Panel. Keep tapping a button on the panel, for instance, Resolution, to cycle through the available settings. Note The available settings on the menu depend on the Capture mode selected. 6 1 5 2 4 3 1 Resolution. Tap to change the resolution. See the table in the previous page for the detailed capture sizes. 2 Storage.
Experiencing Multimedia 195 4 Self-timer. Tap to set the self-timer to 2 seconds, 10 seconds, or Off when in the Photo or Contacts Picture mode. When you press the CAMERA or ENTER button to capture a still image, it starts to count down, and then captures a still image after the assigned time. 5 Brightness. Tapping the minus/plus icon ( / ) decreases or increases the brightness level. 6 White Balance. White balance enables the camera to capture colors more accurately in different lighting conditions.
Experiencing Multimedia Capture mode Photo Video MMS Video Contacts Picture Picture Theme Panorama Sports Burst Capture size setting Zoom range 3M (2048 x 1536) No zooming available 2M (1600 x 1200) No zooming available 1M (1280 x 960) 1.0x to 2.0x Large (640 x 480) 1.0x to 2.0x Medium (320 x 240) 1.0x to 4.0x Small (160 x 120) 1.0x to 8.
Experiencing Multimedia 197 The Review screen After taking a still image or recording a video clip, you can view, send, or delete the image or video clip on the Review screen. You can also tap the following icons at the bottom of the Review screen: Icon Function Back Return to the live Camera screen. Delete Remove the captured image or video. Send Send via e-mail or MMS. View View the image in the Camera Album program, or play the captured video in Windows Media® Player.
Experiencing Multimedia Camera settings Tap the Menu icon ( ) to open the Camera Settings screen. The Camera Settings screen allows you to configure capture and camera settings. The Camera settings consist of two tabs: Capture Settings and Advanced. Use the Capture Settings tab to adjust options for your selected capture mode; Use the Advanced tab to set the Camera program preferences. You can either tap on-screen or press the Navigation Control buttons to navigate the Camera Settings screen.
Experiencing Multimedia 199 • Quality. Select the JPEG image quality level for all captured still images. Choose from Basic, Normal, Fine, and Super Fine. • Metering Mode. Select a metering mode to allow the camera to measure the amount of light and calculate the best-fit exposure value before capturing. Choose either Center Area to measure light using the center area of the image or Average to measure light using the area all around the image. • Storage. Select where you want to save your files.
Experiencing Multimedia • Keep Backlight. Turn the backlight on or off. This overrides your device backlight settings while you are using the camera. • Review Duration. Set a time length for displaying the captured image/video on the Review screen. Select No Limit if you do not want to impose a time limit. Select No Review to immediately return to the live Camera screen after capturing and saving. • Flicker Adjustment.
Experiencing Multimedia 201 • Image Properties. This option lets you adjust the camera display properties, such as Contrast, Saturation, Hue, and Sharpness. 2 1 Tap a property to adjust. 2 Tap the left/right arrow icon or press NAVIGATION left/right (in landscape orientation) to increase/decrease the value. 3 Tap to close the submenu without applying and saving the changes. 4 Tap to reset all properties to their default values. 5 Tap to save the settings.
Experiencing Multimedia 12.2 Camera Album Use the Camera Album to view images and videos that you captured using the Camera program. Camera Album offers a host of features that let you rotate images, view your images as a slide show, use images as contact pictures, and more. Note Only files supported by the Camera program are displayed in Camera Album. To know which file formats are supported, see “File formats supported" in the Camera section.
Experiencing Multimedia 203 To view an image On the main Camera Album screen, touch the thumbnail of the image you want to view. While viewing the image, you can zoom in or rotate the image. To learn how to zoom and rotate the image, see the succeeding procedures. While viewing an image, touch the screen or press ENTER to open the onscreen menu. Icon Function Icon Function Touch to send the image via one of your Messaging accounts. Touch to start the slide show.
Experiencing Multimedia To rotate the image 1. View the image you want to rotate. 2. With your finger, make a semicircle motion on the screen. Slide your finger clockwise to rotate the image 90 degrees clockwise. Slide your finger counter-clockwise to rotate the image 90 degrees counterclockwise. To zoom in or out of an image While viewing an image, make a full circle motion on the screen with your finger. Slide your finger clockwise on an area to zoom in on that area.
Experiencing Multimedia 205 To view the images as a slide show On the Camera Album screen, touch Slide Show. While viewing the slide show, touch the screen to show playback controls. Touch to open the slide show options where you can set the transition effect to use, time per slide, and orientation of the images. Touch to go back to the previous image. Touch to return to the main Camera Album screen. Touch to play or pause slideshow playback. Touch to go to the next image.
Experiencing Multimedia 12.3 Pictures & Videos Pictures & Videos allows you to manage the following types of media files on your device: File Type File Extensions Image *.bmp, *.jpg, *.gif, *.png GIF animation *.gif Video *.avi, *.wmv, *.mp4, *.3gp, *.3g2 Audio *.wma To open Pictures & Videos • Tap Start > Programs > Pictures & Videos. To copy media files to your device • Copy pictures and GIF animation files from your PC or a storage card to the My Pictures folder on your device.
Experiencing Multimedia 207 To play GIF animation files 1. Select a GIF animation file (marked with a icon) and tap View. 2. The GIF Animation program then opens and plays the animation. To play videos 1. By default, the contents of the My Pictures folder will be shown. 2. To find the video clips that you captured, tap the down arrow ( ) next to the My Pictures folder and tap My Documents > My Videos. Video clips are displayed as thumbnails by default, which appear with a media icon ( ). 3.
Experiencing Multimedia • • To crop a picture, tap Menu > Crop. Next, tap and drag to select the area to crop. Tap inside the box to crop, or tap outside the box to cancel cropping. To adjust the brightness and contrast levels of a picture, tap Menu > Auto Correct. Note To undo an edit, tap Menu > Undo. To cancel all unsaved edits you made to the picture, tap Revert to Saved. 12.
Experiencing Multimedia 209 About the controls The following are available controls on the Windows Media® Player Mobile. Tap and drag to jump to any part of the video or audio Mute/Unmute Full screen Increase Volume Visit WindowsMedia.com Decrease Volume Skip to the beginning of Skip to the next file the current file or to the Play/Pause previous file About the screens and menus Windows Media® Player Mobile has three primary screens: • Playback screen.
Experiencing Multimedia Synchronize video and audio files Use the latest version of Windows Media® Player on your PC to synchronize digital media files from your PC to your device. This ensures that protected files and album art (for skins) are copied to your device correctly. To synchronize content to your device automatically 1. On your PC, start Windows Media® Player and then connect your device to your PC. 2. In the Device Setup Wizard, select Yes, search my computer now.
Experiencing Multimedia 211 Playlists and Library List Content List Sync List 4. Click Start Sync to start synchronizing the selected files to your device. Notes • Use Windows Media® Player 11 or higher on your PC to synchronize media files to your device. • Audio files copy faster if Windows Media® Player is configured to automatically set the quality level for audio files copied to your device. For more information, see the Windows Media® Player Help.
Experiencing Multimedia To play video and audio files on your device 1. Select a category (for example, My Music or My Playlists). 2. Tap and hold the item that you want to play (such as a song, album, or artist name), then tap Play. Tips • To play a media file that is stored on your device but is not in a library, on the Library screen, tap Menu > Open File. Tap and hold the item that you want to play (such as a file or a folder), then tap Play.
Experiencing Multimedia 213 12.5 Streaming Media Streaming Media lets you stream live broadcasts or on-demand media content from the Web. The media is sent in a continuous stream to your device and is played as it arrives, along with the audio. The Streaming Media program allows you to play 3GP and MPEG-4 files. It also supports playback of SDP (Session Description Protocol) files.
Experiencing Multimedia To stream media files directly on the Streaming Media Player Streaming Media only supports RTSP links when you stream *.3gp and *.mp4 files directly on the program. Note Before you launch the Streaming Media program, make sure that you are connected to the Internet. 1. Tap Start > Programs > Streaming Media. 2. From the program, tap Connect. 3. Enter the URL for the Web site (rtsp://) and the file name. 4. Tap Connect. 5. Streaming Media then starts playing the file.
Experiencing Multimedia 215 12.6 Audio Manager Audio Manager is a music browser and player in one. It gives you access to all the music files on your device, and allows you to easily browse for the music that you want to play by organizing music into categories such as title, artist, album, etc. You can also create playlists of your favorite songs and use the integrated Music Player to play them back. To launch Audio Manager • Tap Start > Programs > Audio Manager.
Experiencing Multimedia When you tap a category on the Library’s Main screen, you will see more submenus which may have deeper levels of menus. For example, when you tap Artists, another level of submenus will be listed showing artist names. When you tap an artist name, more submenus showing album names will be displayed. Keep opening the submenus until you reach the level where song titles can be selected for playback.
Experiencing Multimedia 217 Playlists The Playlists screen shows the current playlists that are found on the device memory and memory card. There are two types of playlists that will be shown on the Playlist screen: • Windows Media® Player playlists. These are playlists that are in Windows Media® Player Mobile’s Library (which is synchronized with Windows Media® Player on your computer), and they are indicated by the Windows Media® Player icon ( ).
Experiencing Multimedia To play back a playlist 1. On the Playlists screen, tap to select a playlist. 2. Tap the first song in the selected playlist. Music Player automatically opens and starts playing the first song. After each song, the next one in the playlist will be played. Note The content of playlists is not automatically updated when music files have been deleted from the device memory or memory card.
Experiencing Multimedia 219 12.7 Using Audio Booster Audio Booster enhances your music experience by providing you with controls for adjusting sound settings while you are listening to music. It adds 3D sound, treble and bass effects, and provides controls for adjusting them. It even has an equalizer with presets as well as a control panel for fine tuning sound. To access Audio Booster • Tap Start > Programs > Audio Booster.
Experiencing Multimedia This control Does this 6 • Tap Menu > Cancel to exit Audio Booster without applying Menu the modified settings: • Tap Menu > Reset to change back to the default settings. Equalizer The Equalizer optimizes sound for a better listening experience. It provides preset moods, such as hip hop, jazz, rock, etc., and several enhancement presets that suit different types of music. It also has a 10-band graphic equalizer that lets you adjust the loudness of sound by frequency.
Experiencing Multimedia 221 To apply a preset 1. Select the Equalizer check box to enable the equalizer. 2. Tap the list box then select a desired preset. 12.8 Using FM Radio FM Radio allows you to listen to FM radio stations on your device. Since FM Radio uses the provided stereo wired headset as an antenna, you must plug in the headset first onto the earphone jack of your device before you open the program. You can switch between the wired headset and speaker when listening to FM.
Experiencing Multimedia FM Radio controls 1 2 7 8 3 4 5 9 10 11 6 Tip Tap Menu to choose more options for FM Radio, such as Scan & Save to perform a rescan of the FM band for available FM stations and save them as presets, and more. This control Does this 1 Turns off the FM radio. 2 See “Radio Display” for details. 3 Decreases the radio frequency by 0.1MHz. 4 Stereo/Mono Allows you to switch between Mono and Stereo modes.
Experiencing Multimedia 223 This control Does this 10 Turns the sound on or off. 11 Adjusts the volume. Tap to increase the volume. Tap to decrease the volume. The volume level is displayed below the icon. Radio Display 1 Shows the station name when the RDS (Radio Data System) or RDBS (Radio Data Broadcast System) signal is available. 2 Shows the preset number when you select a preset FM station. 3 Shows the received signal strength. 4 Shows the radio frequency.
Experiencing Multimedia Saving presets Presets are favorite FM stations that you can save for easy access. You can save up to six FM stations to the preset buttons on the main FM Radio screen, or save up to 20 presets on the Presets screen. To save FM stations to the preset buttons 1. Tune to the desired FM frequency. Tap here 2. Tap the number on a preset button. The frequency number of your favorite FM station will be displayed on the preset button.
Experiencing Multimedia 225 FM Radio Main Menu Tap Menu on the FM Radio screen to access options for the FM Radio program. Scan & Save Automatically scan radio stations that can be picked up by the device and save them as presets. Existing presets will be cleared and replaced with the newly scanned radio stations. You can have a maximum of 20 preset radio stations. Stereo Toggles between using Stereo or Mono mode when listening to an FM radio station. Mute Toggles between muting and restoring the volume.
Experiencing Multimedia
Chapter 13 Managing Your Device 13.1 Adding and Removing Programs 13.2 Using Task Manager 13.3 Resetting Your Device 13.4 Managing Memory 13.5 Windows Update 13.
Managing Your Device 13.1 Adding and Removing Programs Before you purchase additional programs for your device, make sure that they are compatible with your device. To add programs 1. Download the program to your PC (or insert the CD or disk that contains the program into your PC). You may see a single *.exe file, a *.zip file, a Setup.exe file, or several versions of files for different device types and processors. Be sure to only select programs designed for your device and processor type. 2.
Managing Your Device 229 To configure the Exit ( ) button You can configure the Exit button to shut down running programs when the button is tapped, or to just temporarily close the program screen but keep the program running. 1. On the Task Manager screen, tap the Button tab. 2. Select the Enable the “X” button to end running programs check box. Note When the Enable the “X” button to end running programs check box is not selected, tapping the Exit button will only close a program screen.
Managing Your Device To set the sorting preference for running programs in the Quick Menu 1. On the Task Manager screen, tap the Advanced tab. 2. Choose whether to sort according to Program name or Memory usage. The list will be sorted in ascending order. 13.3 Resetting Your Device Soft reset Occasionally, you may need to reset your device. A soft (or normal) reset of your device clears all active program memory and shuts down all active programs.
Managing Your Device 231 Important If Encrypt files placed on storage cards is or was enabled before, then backup all files from the storage card before using Clear Storage, performing a hard reset, or updating the ROM system software. Otherwise you will no longer be able to access the encrypted files on the storage card. Use ActiveSync or Windows Mobile Device Center to transfer files between your storage card and computer. After the procedure, copy your files back to the storage card.
Managing Your Device 13.4 Managing Memory To see how much memory is available for use, tap Start > Settings > System tab > Memory. On the Main tab, the amount of memory allocated to data storage versus program storage is displayed, as well as the amount of memory in use versus the available memory. To see available storage card memory, tap Start > Settings > System tab > Memory > Storage Card tab.
Managing Your Device 233 13.5 Windows Update You can update Windows Mobile® on your device with the latest updates, security patches or fixes, if they are available. To set up Windows Update The first time you run Windows Update, you need to set up how you want Windows Update to check for patches on the Microsoft Web site. 1. Tap Start > Settings > Systems tab > Windows Update. 2. On the Update Setup screen, tap Next. 3. Select how you want to check for updates, Manual or Automatic, then tap Next.
Managing Your Device 13.6 Battery Saving Tips How long your battery power lasts depends on battery type and how you use your device. Try the following to help preserve battery life: • When the device is not in use, press POWER to switch off the display. • Tap Start > Settings > System tab > Power to open the Power settings screen. On the Advanced tab of the Power settings screen, you can specify when your device automatically turns off the display to conserve battery power.
Chapter 14 Using Other Applications 14.1 Voice Speed Dial 14.2 Java 14.
Using Other Applications 14.1 Voice Speed Dial You can record voice tags so that you can dial a phone number or launch programs simply by speaking a word. Create a voice tag for a phone number 1. Tap Start > Contacts to open the Contacts list. 2. Do one of the following: • Tap and hold the desired contact, then tap Add Voice Tag. • Select the desired contact, then tap Menu > Add Voice Tag. • Tap the desired contact to open the contact’s detailed screen, then tap Menu > Add Voice Tag. 3.
Using Other Applications 237 5. When you create a voice tag for the item, you can do one of the following: • • • Tap the Record button to rebuild the voice tag. Tap the Play button to play the voice tag. Tap the Delete button to delete the voice tag. Create a voice tag for a program 1. Tap Start > Settings > Personal tab > Voice Speed Dial > Application tab. 2. The Application tab displays a list of all installed programs on your device.
Using Other Applications 14.2 Java MIDlets are Java applications such as games and tools that can run on mobile devices, while a MIDlet suite is a collection of one or more MIDlets. The Java program lets you download, install and manage MIDlets or MIDlet suites on your device. Your device supports Java 2 Micro Edition, J2ME. To open the Java program • Tap Start > Programs > Java. Install and launch MIDlets/MIDlet suites There are several ways to install a MIDlet/MIDlet suite.
Using Other Applications 239 To run a MIDlet/MIDlet suite Do one of the following: • After installation of the MIDlet/MIDlet suite is complete, tap Yes. • On the Java screen, open the folder that contains the MIDlet/MIDlet suite. Select the MIDlet/MIDlet suite then tap Launch. To stop running a MIDlet/MIDlet suite • Tap Exit or Quit if presented on the MIDlet/MIDlet suite’s screen or menu.
Using Other Applications 14.3 Spb GPRS Monitor Using Spb GPRS Monitor, you can monitor how much data you have sent and received on your device, and check the network usage costs by taking into account your service plan details. You can also view connection cost and traffic charts, generate reports of network connection usage, and export reports to CSV files for use with Microsoft® Office Excel® and Access. Install GPRS Monitor The GPRS Monitor program is included on the Application CD.
Using Other Applications 241 The GPRS Monitor icon and pop-up window Another way of displaying status information visually is by enabling the GPRS Monitor icon to be shown on the title bar. This icon shows the GPRS/ dial-up connection speed, data traffic, and battery status. To show the GPRS Monitor icon on the title bar 1. Tap Start > Programs > Spb GPRS Monitor. 2. Tap Tools > Options > Icon tab. 3. Select the Show taskbar icon check box.
Using Other Applications To enter your service plan details Service plan details, or tariffs, determine the price that you pay for your data transfers. The tariff may either be flat rate or time-based, depending on whether you’re using GPRS or a phone dial-up connection for data transfers. Contact your service provider to find out about your tariff, and enter the information in the Tariff tab or the Tariff Details tab on the Options screen.
Appendix A.1 Regulatory Notices A.
Appendix A.1 Regulatory Notices Regulatory Agency Identifications For regulatory identification purposes, your product is assigned a model number of POLA100. To ensure continued reliable and safe operation of your device, use only the accessories listed below with your POLA100. The Battery Pack has been assigned a model number of POLA160. Note This product is intended for use with a certified Class 2 or Class 3 Limited Power Source, rated 5 Volts DC, maximum 1 Amp power supply unit.
Appendix 245 • • • • • • ETSI EN 301 489-17 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment.
Appendix This equipment may be operated in: AT BG CH CY CZ DE DK EE ES BE FI FR GB GR HU IE IT IS LI LT LU LV MT NL NO PL PT RO SE SI SK TR Safety precautions for RF exposure • • Use only original manufacturer-approved accessories, or accessories that do not contain any metal. Use of non-original manufacturer-approved accessories may violate your local RF exposure guidelines and should be avoided.
Appendix 247 it is recommended that no part of the human body be allowed to come too close to the antenna during operation of the equipment. Your device has an internal antenna. Use only the supplied integral antenna. Use of unauthorized or modified antennas may impair call quality and damage the phone, causing loss of performance and SAR levels exceeding the recommended limits as well as result in non-compliance with local regulatory requirements in your country.
Appendix Hearing Aids Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may want to consult your service provider, or call the customer service line to discuss alternatives. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if they are adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information.
Appendix 249 RoHS Compliance This product is in compliance with Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003, on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) and its amendments. A.2 Specifications System Information Processor Qualcomm® MSM7200TM 400MHz Memory – ROM : 256 MB – RAM : 128 MB DDR SDRAM Note: Figures are the total ROM and RAM memory available for use and storage.
Appendix HSDPA / UMTS / GSM / GPRS / EDGE Module Functionality HSDPA/UMTS: 2100MHz for Europe, 850/1900MHz for USA HSDPA: Up to 384kbps for upload and 3.6Mbps for download UMTS: Up to 384kbps for upload and download GSM/GPRS/EDGE: Quad-band (850, 900, 1800, and 1900) Internal Antenna Yes Physical Dimensions 110 mm (L) x 58 mm (W) x 15.5 mm (T) Weight 130 g (with battery) Camera Module Type Main camera: 3.
Appendix 251 FM Radio/RDS Chipset TI BRF6350 Tuning Range 76 - 108 MHz Frequency Response 20~15 kHz Auto Channel Search Yes RDS/RBDS • Radio Data Service (RDS)/Radio Broadcast Data Service (RBDS) decoder • Integrated RDS/RBDS demodulator in accordance with EN50067 Controls and Lights Device Control • • • • • • LEDs The right bi-color LED shows green and amber lights for HSDPA/UMTS/EDGE/GSM/GPRS standby, message, and network status as well as for notification and battery charging status.
Appendix
Index Symbols 3D sound 219 3G 153 A A2DP 166 ActiveSync - set up 91 - synchronize 92, 131 Add and remove programs 228 Adobe Reader LE 47, 141 Alarm 82 Answer/end a call 69 Appointment search 62 Attachment - add to e-mail 123 - download 125 Audio Booster 47, 219 Audio Manager 47, 215 B Backlight 80, 81 Back up data 144 Basic settings 80 Bass effects 219 Battery - battery information 22 - charge battery 27 - save battery power 153, 234 Beam - via Bluetooth 167 Block Recognizer 60 Bluetooth - Bluetooth E
Index Car kit phones 77 Clear Storage 231 Clock & Alarms 50, 80 Comm Manager 47, 52, 148 Company Directory 137 Conference call 70 Configure data connection settings 26 Connection Setup 149 Connect device to Internet - Dial-up 154 - GPRS/3G 153 - start a connection 155 - ways of connecting 150 Contacts 46, 96 Contacts Picture capture mode 191 Contacts search 62 Copy - contacts to SIM card 100 - copy and manage files 142 - media files from PC to device 210 - SIM contacts to device 100 Customize - Start menu
Index 255 I IMAP4 120 Input methods - Block Recognizer 60 - Keyboard 55 - Letter Recognizer 60 - Symbol Pad 59 - Transcriber 61 Input Panel 54 International call 77 Internet 150 Internet Explorer Mobile 46, 155 Internet Sharing 47, 162 J Java - create folders 239 - install MIDlets/MIDlet suites from device 238 - install MIDlets/MIDlet suites from Internet 238 - manage MIDlets/MIDlet suites 239 - overview 47 - rename MIDlet or folder 239 - uninstall MIDlets 239 - update a MIDlet/MIDlet suite 239 K Keyb
Index N Network Wizard 26, 44 Notes 47, 107 Notes search 62 Now Playing screen (Windows Media Player Mobile) 209 O Office Mobile 46, 140 Open PDF file 141 Owner information 84 P Panning - finger panning 41 Panorama capture mode 191 Password 85 Phone 46, 64, 66 Phone services 83 Photo capture mode 191 Pictures & Videos - edit picture 207 - file formats 206 - overview 48 - play GIF animation 207 - play videos 207 - view pictures 206 Picture Theme capture mode 191 PIN 64, 85 Playback screen (Windows Me
Index 257 Scrolling - finger scrolling 41 Search 48, 62 Send - e-mail 123 - MMS message 116 - text message (SMS) 113 Settings 80 - camera 194 Settings (Connections tab) - Beam 52 - Bluetooth 52, 164 - Comm Manager 148 - Connections 52, 153, 154 - CSD Line Type 52 - GPRS Setting 52 - HSDPA 52 - Network Wizard 52, 149 - SMS Service 52 - USB to PC 52, 93 - Wi-Fi 52 - Wireless LAN 52 Settings (Personal tab) - Buttons 49 - Input 49 - Large Start Menu 49 - Lock 49, 85 - Menus 49, 85 - Owner Information 49, 84 - Ph
Index - copy files 143 - encrypt 86 Streaming Media 48, 213 Swap/switch calls 70 Synchronize - ActiveSync 92 - change information types 92 - via Bluetooth 93 - Windows Media Player 94, 210 - with computer 92 - with Exchange Server 130 System information 249 T Tasks 48, 105 Tasks search 62 Task Manager 228 Text messages - copy from and to SIM card 114 - send 113 Text size (screen) 81 Today screen 29, 83 TomTom NAVIGATOR 48, 178 TouchFLO 37, 51, 67 Touch Cube (TouchFLO) 37 Touch Keyboard 55 Touch Keypad
Index 259 Z ZIP - create archive 144 - open zip file and extract files 143 - overview 49, 143 Zoom (Camera) 195
Index