Wireless Alarm System User Manual
1.
Power Tone ON/OFF Power : power jack(DC5V) ON/OFF: power switch(turn on/off the wireless alarm receiver) set button(add/delete the sensors of the wireless alarm receiver) Tone: Choose the ring tones(total 35 ring tones optional) Volume:Press and hold the“ON/OFF”button first,and then press the“Tone”button to adjust the alarm volume,total 4 volume levels.
Bubble Level: easy to know the beams be installed horizontally Infrared Beam: used to detect the intruder Calibration Hole: easy to align with another beam sensor if the beams apart far away Solar Panel: charge the battery of the beam sensor even in cloudy or rainy days LCD Display: easy to know how well the beam sensor be aligned with each other ON/OFF: turn on/off the solar beam sensor Charge Jack:pull out the red plug to charge the solar beam sensor by DC5V-12V power adapter if the battery of the beam se
Step2: Turn on the Solar &Wireless Photoelectric Beams: Press the ON/OFF button 3 times(Both the transmitter and receiver) Transmitter Receiver (more than 3 short beeps mean the built-in batteries of the sensor have enough power) Make Step 3sure the beams aligned with each other (bleep prompt and LCD display more than “100” means the beam sensors work properly, Please note: “100” is a reference value, different weather will get different value and bigger value means better alignment ) Step 4 Power on th
Step 5 Trigger the sensor (completely block all the 3 infrared beams by thick materials, such as books,and the wireless alarm receiver will alarm for several seconds) Step 6 Press“Tone” button to choose the ring tone for this sensor, there are 35 tones to choose from; Tone Step 7 Adjust the alarm volume. Press and hold the“ON/OFF”button first,and then press the“Tone”button to adjust the alarm volume, total 4 volume levels adjustment.
Step 8 Installation 1st Installation method T R T R Calibration (1)Place the beam sensor on the same height. (2)Ensure the beam sensor is vertical (the bubble of the horizontal pipe should be in the middle). (3)Adjust the direction of the beam sensor to make them align with each other. Calibration Hole:used to find another device. LCD Display:used to know how well the beam sensor be aligned with each other (the LCD Display will shut down in an hour).
2nd Installation method(with iron brackets) 7
R T T R Calibration (1)Place the beam sensor on the same height. (2)Ensure the beam sensor is vertical (the bubble of the horizontal pipe should be in the middle). (3)Adjust the direction of the beam sensor to make them align with each other. Calibration Hole:used to find another device. LCD Display:used to know how well the beam sensor be aligned with each other (the LCD Display will shut down in an hour).
4.
Step 4 Trigger the sensor again to confirm the sensor has been added to the wireless alarm receiver already.
(3)How to adjust the alarm volume Step 1 Power on the wireless alarm receiver by the power adapter Step 2 Press and hold the“ON/OFF”button first,and then press the“Tone”button to adjust the alarm volume,total 4 volume levels ON/OFF Tone (4)How to change the ring tone for the sensors Step 1 Power on the wireless alarm receiver by the power adapter Step 2 Trigger the sensor first,and then press the "Tone" button to choose the ring tone for this sensor; Same steps for other sensors which have been added to t
Step 2: Press and hold the ON/OFF button for 10 seconds and release the button when you hear bleep prompt,and then press the ON/OFF button 6 times quickly( both the transmitter and receiver ) Note:if adjust the sensitivity of the beams back to factory default ( 200ms ) ,press the ON / OFF button 5 times Step 3: Make sure the solar beams aligned with each other Step 4: Press and hold the ON/OFF button for 10 seconds and release the button when you hear bleep prompt (only the receiver) Step 5: Press the ON/OF
Solar&Wireless Photoelectric Beam Sensor 40mm 39mm 245mm 85mm 40mm 184mm 84mm 45mm Technical parameters Item Infrared Detection Range Wireless Transmission Range Beam Quantity Wireless Frequency Maximum Trigger Number In 24 Hours Working Voltage Battery Type Battery Capacity Static working Current Infrared Wavelength Technical Parameters 100m(300 feet) 1KM(3000 feet) 3 433MHz FSK+FHSS ≤200 times 3.3V Chargeable LiFePO4 Battery Transmitter:500mAh,Receiver:500mAh ≤0.
