User's Manual

ManualsBrandsHTZSAFE ManualsElectronicsSolar Wireless Motion Sensor

Table Of Contents

Solar Wireless Motion Sensor

Sensor Eye

Sensor Eye: detect the objects

Solar Panel:charge the built-in battery of the sensor

Solar Wireless Motion Sensor

User Manual

1. System Components And Usage

contact@saferhomee.com)

After-sale Service:

E-mail:

Solar Panel

ON/OFF

Charge Jack

Charge Jack:used to connect the additional solar panel

or DC 5V power adapter

ON/OFF:turn on/off the sensor

Summary of content (10 pages)

PAGE 1
Solar Wireless Motion Sensor User Manual After-sale Service: E-mail:contact@saferhomee.com) 1.
PAGE 2
. Operation Instructions (1)How to add sensors to the wireless alarm receiver (up to 32 sensors can be added to the receiver) Step 1 Turn on the Wireless Motion Sensor: Press the ON/OFF button 4 times ON/OFF (press 4 times) (bleep prompt means work normally) Step 2 Power on the wireless alarm receiver by the power adapter Power 2
PAGE 3
Step 3 Press and hold the “ON/OFF” button of the receiver for 5 seconds and release the button when the indicator light flashing; light up ON/OFF flashing ON/OFF release the button press and hold the ON/OFF button for 5 seconds Step 4 Activate The Wireless Motion Sensor (wait about 30 seconds after you turned on the sensor) 1st method:press the ON/OFF button twice ON/OFF (press twice) (the light of the ON/OFF button will flash once means the motion sensor was activated and sent the alarm signal) 3
PAGE 4
2nd method: Ensure the sensor is turned away from you.
PAGE 5
Step 7 Installations Wireless Motion Sensor long screws 1 short screws 2 3 5
PAGE 6
Installation Notes: 1. Please fix the motion sensor tightly to ensure the position and the direction will not be moved easily by wind. 2.Please point the sensor towards a open field(not towards the trees or bushes) 3.
PAGE 7
(3)How to adjust the alarm volume Step 1 Power on the wireless alarm receiver by the power adapter Step 2 Press and hold the“ON/OFF”button first,and then press the“Tone”button to adjust the alarm volume, total 4 volume levels ON/OFF Tone (4)How to change the ring tone for the sensors Step 1 Power on the wireless alarm receiver by the power adapter Step 2 Activate the sensor first,and then press the "Tone" button to choose the ring tone for this sensor; Same steps for other sensors which have been added to
PAGE 8
Step 2 If select Low sensitivity---turn on the sensor by pressing the ON/OFF button 3 times If select Middle sensitivity---turn on the sensor by pressing the ON/OFF button 4 times If select High sensitivity---turn on the sensor by pressing the ON/OFF button 5 times 3.
PAGE 9
ATTENTION PLEASE The KIT inclues a charge cable which is used to charge the solar wireless motion sensor before use or if long-term continuously rainy days caused low battery. Please charge the sensor for 4 hours as below: Charge Jack After-sale Service contact@saferhomee.
PAGE 10
& tĂƌŶŝŶŐ ^ƚĂƚĞŵĞŶƚ ŚĂŶŐĞƐ Žƌ ŵŽĚŝĨŝĐĂƚŝŽŶƐ ŶŽƚ ĞǆƉƌĞƐƐůǇ ĂƉƉƌŽǀĞĚ ďǇ ƚŚĞ ƉĂƌƚǇ ƌĞƐƉŽŶƐŝďůĞ ĨŽƌ ĐŽŵƉůŝĂŶĐĞ ĐŽƵůĚ ǀŽŝĚ ƚŚĞ ƵƐĞƌ͛Ɛ ĂƵƚŚŽƌŝƚǇ ƚŽ ŽƉĞƌĂƚĞ ƚŚĞ ĞƋƵŝƉŵĞŶƚ͘ dŚŝƐ ĞƋƵŝƉŵĞŶƚ ŚĂƐ ďĞĞŶ ƚĞƐƚĞĚ ĂŶĚ ĨŽƵŶĚ ƚŽ ĐŽŵƉůǇ ǁŝƚŚ ƚŚĞ ůŝŵŝƚƐ ĨŽƌ Ă ůĂƐƐ ĚŝŐŝƚĂů ĚĞǀŝĐĞ͕ ƉƵƌƐƵĂŶƚ ƚŽ WĂƌƚ ϭϱ ŽĨ ƚŚĞ & ZƵůĞƐ͘ dŚĞƐĞ ůŝŵŝƚƐ ĂƌĞ ĚĞƐŝŐŶĞĚ ƚŽ ƉƌŽǀŝĚĞ ƌĞĂƐŽŶĂďůĞ ƉƌŽƚĞĐƚŝŽŶ ĂŐĂŝŶƐƚ ŚĂƌŵĨƵů ŝŶƚĞƌĨĞƌĞŶĐĞ ŝŶ Ă ƌĞƐŝĚĞŶƚŝĂů ŝŶƐƚĂůůĂƚŝŽŶ͘ dŚŝƐ ĞƋƵŝƉŵĞŶƚ ŐĞŶĞƌĂƚĞƐ ƵƐĞƐ ĂŶĚ ĐĂŶ ƌĂĚŝĂƚĞ ƌĂĚŝŽ ĨƌĞƋƵĞŶĐǇ ĞŶĞƌŐǇ ĂŶĚ͕ ŝĨ ŶŽƚ ŝ