AP6510DN-AGN-US Outdoor Wireless LAN Access Point Quick Start Guide HUAWEI TECHNOLOGIES CO., LTD.
Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.
Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol CAUTION NOTE Description Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Provides additional information to emphasize or supplement important points of the main text. Change History Changes between document issues are cumulative.
AP6510DN-AGN-US Quick Start Guide Technical Support 技术支持 Before performing Installation, confirm that the installation accessories and tools are available.
Installing an AP ● Select an appropriate installation position and leave space above and around the device for cooling air circulation. ● Outdoors Aps are used for hotspot coverage and often installed against walls or poles. The pole diameter is 48 mm to 114 mm. 306 AP6510DN-AGN-US dimensions (unit: mm) without a backplane Recommended AP6510DN-AGN-US installation space (unit: mm). support. 330 83 ● Installing the AP6510DN-AGN-US against a Wall: 2.
Installing an AP ● Installing the AP6510DN-AGN-US against a vertical pole: 2. Slide the AP that has the connector fastened into the wall1. Determine the AP installation position, slide the hoop mounting bracket. through the hole of the wall-mounting bracket and attach it to the pole, And use the screwdriver to secure screws on the hoop.
Installing Cables ● AP6510DN-AGN-US external cable arrangement drawing Feed line Feed line Feed line Feed line Ground cable Network cable ● Connecting network cables 1. Use a shield straight-through cable. Cut the cable of proper length based on the distance between the AP and the PSE device, peel the insulation on both ends of the network cable, and crimp the wires to RJ45 connectors. 2. Make a network cable onsite according to the following pin assignment.
Installing Cables ● Connecting the feed line 1. The outdoor AP's antenna ports already have 5 KA surge protection capability. Generally, no surge protection devices need to be installed; therefore, the antenna cables are directly connected to the AP's antenna ports. Feed line Waterproof adhesive tape 2. If higher surge protection capability is required, the customer can purchase a surge protection device. When installing the surge protection device, ensure that it is connected to a ground cable.
Installing Cables CAUTION Requirements for laying out ground cables: 1. All ground cables must be connected to a ground bar. 2. The ground cable cannot be led in aerially, but buried in the earth or arranged indoor. 3. Both ends of the external conductor of the coaxial cable and those of the insulation of the shielded cable should have good electric contact with the metal shell of the equipment they connect to. 4. Ground cables must be separated from signal cables to reduce interference between them. 5.
Power-on NOTE 2 连接线缆 Information Type Startup status The AP6510DN-AGN-US supports the PoE function that complies with 802.3at. Power on the AP6510DN-AGN-US and check the indicator status to determine the system running status. SYS Link Description Wireless Steady green NA NA The device is being started. Blinking green NA NA The system is working properly. Steady red NA NA Off Blinking once every 2s Blinking green The system is working properly, but the Ethernet is not connected.
Logging In to the Router After an AP is powered on, you can log in to the AP using the following methods. 1. Logging In to the AP Using Telnet This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using commands. 1. Logging In to the AP Using Telnet This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using Commands.
Declaration on Hazardous Substances in Electronic Information Products Hazardous Substances Part Pb Hg Cd Cr6+ PBB PBDE Mechanical part O O O O O O Board/circuit module O O O O O O Signal cable O O O O O O Cable connector O O O O O O Power adapter O O O O O O Auxiliary equipment O O O O O O O: Indicates that the concentration of the hazardous substance contained in all the homogeneous materials of this part is below the limit requirement of the SJ/T 11363-200
Warranty Card Thank you for choosing HUAWEI Technologies Co., Ltd-a leading telecom solution provider. To get better services, please read this warranty card carefully, fill in the required information and preserve this card in good condition. Your Name Address/Postal Code Telephone Product Type Product Serial Number Purchase Date Invoice Number Dealer Name Dealer´s Address/Telephone Preserve well. No reissue Dealer´s Seal: Limited Warranty Subject to the exclusions contained below, Huawei Technologies CO.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China http://enterprise.huawei.
